Evaluation of multiaxial stress in textured cubic films by x-ray diffraction

X-ray diffraction is used extensively to determine the residual stress in bulk or thin film materials on the as- sumptions that the material is composed of fine crystals with random orientation and the stress state is biaxial and homogeneous through the x-ray penetrating region. The stress is calculated from the gradient of ε ～ sin^2 φ linear relation. But the method cannot be used in textured films due to nonlinear relation. In this paper, a novel method is proposed for measuring the multiaxial stresses in cubic films with any [hkl] fibre texture. As an example, a detailed analysis is given for measuring three-dimensional stresses in FCC films with [111] fibre texture.     

室外高光谱BRDF自动测量系统的设计

室外BRDF(Bidirectional reflectance distribution function)测量随着遥感的发展越来越重要。室外测量要求测量周期短、测量点多、光谱分辨率高。为了满足这一要求,设计了室外高光谱BRDF自动测量系统。系统主要由自动测量架和光谱仪器组成。测量架半径为2m,主要由天顶弧轨道、方位圆轨道、伺服电机、PLC组成。光谱仪器包括一台亮度计和一台照度计,亮度计测量反射亮度,被固定在测量架小车平台上,照度计测量入射照度。两台光谱仪器采用相同的平场凹面光栅分光、线阵列探测器探测。光谱测量范围为400~2500nm,光谱分辨率为3.5nm(400~1000nm)、12nm(1000~2500nm)。系统在工控机的控制下完成自动测量。在自动默认状态下测量周期大约为10min。     

Influence of laser irradiation on the optical and structural properties of poly(ethylene terephthalate) fibres

Laser irradiation has been previously investigated for achieving uniform heating of polyethylene terephthalate (PET) fibres in the hot-drawing stage of the production process, so as to obtain better fibre mechanical properties. The optical properties and dye uptake of PET fibres also depend on the polymer chain orientation and crystallinity within the fibre structure. This paper reports an investigation of a concept whereby laser irradiation and interferometry could be used to modify and trace a small change in the optical properties of a PET monofilament fibre, but the corresponding change in the dye uptake would not be detected visually. A copper vapour laser (550-580 nm wavelengths) was used to expose consecutive 4 mm lengths along a running length of monofilament to 39.8 W cm⁻², at a pulse rate of 9.89 kHz in order to modify, in a controlled way, the polymer crystallinity and orientation. A 3D finite element simulation, based on uncoupled heat-transfer analysis, indicated that rapid heating and cooling could be obtained with the laser to give the small changes required. Irradiated and untreated samples were analysed by interferometry and a 0.16% change was detected in the birefringence profiles, corresponding to a small reduction in the degree of orientation and crystallinity of the irradiated samples. Density measurements and wide-angle X-ray scattering (WAXS) analysis confirmed the change in crystallinity. Tests conducted for dye adsorption and tensile strength showed a small increase in the former and only a very small decrease in the latter. It was concluded that these changes in property provide the opportunity for a laser-irradiated PET monofilament fibre to be used as a subtle tracer element in brand labels for textile garments as an anti-counterfeit measure.     

UV photodetector behavior of 2D ZnO plates prepared by electrochemical deposition

Zinc oxide (ZnO) with 2D hexagonal structure was successfully prepared using electrochemical deposition (ECD) method on a quartz substrate pre-coated with indium-doped ZnO layer. The X-ray diffraction of the prepared sample confirmed that the hexagonal structure had a dominant c-axis orientation. The scanning electron microscopy revealed the 2D hexagonal structure of the prepared ZnO.     

Optical path automatic compensation low-coherence interferometric fibre-optic temperature sensor

An interferometric fibre-optic temperature sensing system employing a light emitting diode (LED) as the broadband optical source and a single mode fibre coil which was fabricated in a definite length as the sensor head is described. A reference fibre line transmitting back and forth along the same path as the sensing transmitting fibre is used, so the change caused by the environmental temperature fluctuation of the fibre path can automatically be compensated. The sensitivity of the sensing system can be easily improved by using the long length of the sensing fibre. The experiment results of the sensing gauge length versus the sensitivity are given. Two typical wavelengths (1300 and 1550 nm). LED sources are used, it is shown that the sensitivity of the system between the two wavelengths is different. The experimental curve of the resolution characteristic of the system related to the length of sensing fibre coil is also discussed.     

Orientation distribution of fibres in a channel flow of fibre suspension

The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.     

Electron density modeling and reconstruction of infinite periodic minimal surfaces (IPMS) based phases in lipid-water systems. II. Reconstruction of D surface based phases

This is the second of two papers dealing with the structure of lipid-water phases based on Infinite Periodic Minimal Surfaces (IPMS). The first paper describes mathematical modeling of such phases. In this paper, a new reconstruction method, called the methyl trough search, is described and used to solve the structures based on powder pattern X-ray diffraction data. Structures are derived for both a single chain lipid-water system (mono-olein) and a diacyl phospholipid-water system (2-2 methyl butyl 16:0 phosphatidylcholine). The methyl trough search uses the low electron density of the lipid methyl tails to determine the correct phasing for the electron density reconstruction. The data are consistent with a structure based on the IPMS D surface. The results are compared to other methods used to solve the mono-olein structure; the structure of the diacyl lipid has never before been solved. We discuss the subtleties involved in reconstruction of D surface based phases and the substantial artifacts that arise in low-resolution reconstructions of hydrocarbon lipids lacking heavy-atom sites. Received 15 January 1999 and Received in final form 20 October 1999     

Growth of sputter-deposited Ni-Ti thin films: Effect of a SiO2 buffer layer

In-situ X-ray diffraction (XRD) during the growth of Ni-Ti thin films was chosen in order to investigate their texture development using a deposition chamber installed at a synchrotron radiation beamline. Near-equiatomic films were co-sputtered from Ni-Ti and Ti targets. The texture evolution during deposition is clearly affected by the substrate type and the ion bombardment of the growing film. On naturally oxidized Si(100) substrates, the Ni-Ti B2 phase starts by stacking onto (h00) planes, and as the thickness increases evolves into a (110) fibre texture. For the deposition on thermally oxidized Si(100) substrates, this pronounced cross-over is only observed when a substrate bias voltage (-45 V) is applied. The oxide layer plays an important role on the development of the (100) orientation of the B2 phase during deposition on heated substrates (≈470 °C). If this layer is not thick enough (naturally oxidized Si substrate) or if a bias voltage is applied, a cross-over and further development of the (110) fibre texture is observed, which is considered as an orientation that minimizes surface energies. Electrical resistivity measurements showed different behaviour during phase transformation for the Ni-Ti film deposited on thermally oxidized Si without bias and those on thermally oxidized Si(100) with bias and on naturally oxidized Si(100) without bias. This is related to stresses resultant from the fact that the Ni-Ti films are attached to the substrates as well as with the existence of distinct textures. PACS 81.15.Cd; 61.10.Nz; 68.55.Jk     

Dislocation-based plasticity model and micro-beam Laue diffraction analysis of polycrystalline Ni foil: A forward prediction

A physically-based, rate and length-scale dependent strain gradient crystal plasticity framework was employed to simulate the polycrystalline plastic deformation at the microscopic level in a large-grained, commercially pure Ni sample. The latter was characterised in terms of the grain morphology and orientation (in the bulk) by micro-beam Laue diffraction experiments carried out on beamline B16 at Diamond Light Source. The corresponding finite element model was developed using a grain-based mesh with the specific grain orientation assignment appropriate for the sample considered. Sample stretching to 2% plastic strain was simulated, and a post-processor was developed to extract the information about the local lattice misorientation (curvature), enabling forward-prediction of the Laue diffraction patterns. The ‘streaking’ phenomenon of the Laue spots (anisotropic broadening of two-dimensional (2D) diffraction peaks observed on the 2D detector) was correctly captured by the simulation, as constructed by direct superposition of reflections from different integration points within the diffraction gauge volume. Good agreement was found between the images collected from experiments and simulation patterns at various positions in the sample.     

Diffusive diffraction observed with volume-selective STEAM MRS in 100microm water-filled capillaries

Diffusive diffraction patterns may be useful for probing the local environment of diffusing molecules in materials with geometrically ordered microstructure. A model system consisting in a bundle of water-filled 100microm glass capillaries was probed with volume-selective stimulated echo (STEAM) MRS on a 7T Bruker PharmaScan tomograph with variable diffusion times for both, parallel and perpendicular diffusion-weighting with respect to the capillaries' axes. The precise orientation of the capillaries was determined with image processing methods. Echo attenuation curves were numerically evaluated with respect to the inner radius of the capillaries R and the diffusion coefficient D using equations given in the literature. Good agreement was found between simulation and experiment. For perpendicular diffusion-weighting and diffusion times in the order of R(2)/D two diffraction minima were observed which were not present for shorter diffusion times and for parallel diffusion-weighting. In conclusion, volume-selective diffusive diffraction was observed with a standard small-animal tomograph.     

Discrete rearranging disordered patterns, part II: 2D plasticity, elasticity and flow of a foam

The plastic flow of a foam results from bubble rearrangements. We study their occurrence in experiments where a foam is forced to flow in 2D: around an obstacle; through a narrow hole; or sheared between rotating disks. We describe their orientation and frequency using a topological matrix defined in the companion paper (F. Graner, B. Dollet, C. Raufaste, and P. Marmottant, this issue, 25 (2008) DOI 10.1140/epje/i2007-10298-8), which links them with continuous plasticity at large scale. We then suggest a phenomenological equation to predict the plastic strain rate: its orientation is determined from the foam's local elastic strain; and its rate is determined from the foam's local elongation rate. We obtain a good agreement with statistical measurements. This enables us to describe the foam as a continuous medium with fluid, elastic and plastic properties. We derive its constitutive equation, then test several of its terms and predictions.     

NaY(MoO_4)_2∶Er~(3+)纳米晶体荧光粉的发光与光学温度传感特性(英文)

采用熔盐法制备了不同煅烧温度的NaY(MoO_4)_2∶Er~(3+)荧光粉材料,样品的晶体结构与微观形貌由X射线衍射仪和场发射扫描电镜测得。Er~(3+)掺杂的Na Y(MoO_4)_2纳米晶体的斯托克斯荧光发射光谱是在不同煅烧温度下测得的。NaY(MoO_4)_2∶Er~(3+)荧光粉材料的两个能级~2H_(11/2)-~4I_(15/2)和~4S_(3/2)-~4I_(15/2)跃迁的发射强度比随煅烧温度的增加而减小。NaY(MoO_4)_2∶Er~(3+)荧光粉材料的温度传感特性依赖于Er~3的两个热耦合能级~2H_(11/2)-~4I_(15/2)和~4S_(3/2)-~4I_(15/2)的发射强度。研究表明,在一个相对大的传感温度范围(303~573 K),600℃煅烧的样品的温度传感灵敏度比900℃煅烧的样品高,样品的温度传感灵敏度随煅烧温度的增加而减小,600℃煅烧的样品的温度传感灵敏度为1.36×10~(-2)K~(-1),比900℃煅烧的样品高76.6%。最后,解释了基于不同煅烧温度的温度传感灵敏度的物理机制。     

Quasi-distributed temperature sensor combining Fibre Bragg Gratings and temporal reflectometry technique interrogation

Quasi-distributed sensors based on Fibre Bragg Gratings (FBG) usually deal with the concatenation of FBGs of different Bragg wavelengths analyzed through wavelength-sensitive devices. In these sensors, a given wavelengths range is dedicated to one particular FBG. The number of sensing points is directly limited by the source and detector spectral ranges, and by the wavelength spacing between two gratings. This spacing is linked to the maximum possible excursion of the physical parameter to be measured-before superimposition of the reflection spectra of the FBGs.In this paper, an original interrogating device is presented, that allows a very large number of concatenated gratings to be addressed. In this scheme, identical FBGs (same Bragg wavelength and same low reflectivity) are interrogated by the Optical Time Domain Reflectometry technique, for which a commercial device has been extended to a wavelength-tunable system, within an automated experimental set-up. Detection and localization of an important amount of sensing points along a unique optical fibre is demonstrated. Repeatability measurements did exhibit the very good accuracy of the presented sensor.     

Interface roughness of GaAs/AlAs superlattices MBE-grown on vicinal surfaces

The interface morphology of GaAs/AlAs superlattices grown by molecular beam epitaxy on misoriented (001) GaAs substrates has been investigated using X-ray diffraction techniques in addition to high-resolution transmission electron microscopy (HRTEM). We observe that the width and intensity of the satellite peaks are very sensitive to the step-edge orientation. Among the investigated ones ([ 110], [100], [110]), it is the [ 10] step-edge direction which is the most favourable to a regular growth of superlattice structures. Structural models based on HRTEM observations (step distribution at interfaces and local fluctuation of layer thickness) have been constructed, allowing an explanation of the X-ray diagrams.     

显微镜工作台定位系统的设计与实现

设计了一套基于AT89C52单片机的显微镜工作台定位系统。机械传动部分采用小模数齿轮实现机械运动和动力的传递,单片机电路控制部分实现计数脉冲的获取和电机的控制,上位机控制环节完成用户命令的发布。该系统可以按照预先设定的方式控制电机,实现显微镜工作台的二维运动,两方向重复定位精度±50μm,满足了多波长光存储实验的要求,同时为医疗检验提供了自动化手段。     

Estimation of curl in paper using a combination of shape measurement and least-squares modelling

Curl is a quality problem that makes paper less suitable for printing. A paper sheet that has structural variations in its thickness such as gradients of fibre orientation, density and filler content, will curl and hence assume a cylindrical shape when its humidity content is changed. We propose a method to measure curl that can be used for automated analysis of the paper quality. The shape of the curled paper is measured using a stereoscopic camera system, which is capable of viewing a random pattern that is projected onto the specimen. The shape of the object is found by calculating the perspective difference in the camera set-up using digital image correlation. The quality parameters that are searched for are the magnitude of curl, which is defined as the inverse of the radius of curvature and the orientation of the curled paper. These parameters are estimated by performing a least-squares fit of a cylindrical shape to the three-dimensional measurement data. The least-squares model is non-linear and an iterative technique based on the Gauss–Newton algorithm is used.     

A numerical algorithm for the solution of a phase-field model of polycrystalline materials

We describe an algorithm for the numerical solution of a phase-field model (PFM) of microstructure evolution in polycrystalline materials. The PFM system of equations includes a local order parameter, a quaternion representation of local orientation and a species composition parameter. The algorithm is based on the implicit integration of a semidiscretization of the PFM system using a backward difference formula (BDF) temporal discretization combined with a Newton–Krylov algorithm to solve the nonlinear system at each time step. The BDF algorithm is combined with a coordinate-projection method to maintain quaternion unit length, which is related to an important solution invariant. A key element of the Newton–Krylov algorithm is the selection of a preconditioner to accelerate the convergence of the Generalized Minimum Residual algorithm used to solve the Jacobian linear system in each Newton step. Results are presented for the application of the algorithm to 2D and 3D examples.     

Measuring Electrospun Nanofibre Diameter: a Novel Approach

A new method based on image analysis for electrospun nanofibre diameter measurement is presented. First, the SEM micrograph of the nanofibre web obtained by electrospinning process is converted to binary image using local thresholding method. In the next step, skeleton and distance transformed image are generated. Then, the intersection points which bring about untrue measurements are identified and removed from the skeleton. Finally, the resulting skeleton and distance transformed image are used to determine fibre diameter. The method is evaluated by a simulated image with known characteristics generated by ？-randomness procedure. The results indicate that this approach is successful in making fast, accurate automated measurements of electrospun fibre diameters.     

Novel Fine Structures in Poly-p-phenylenebenzobisoxazole Fibers Induced by Water Vapor,Hot Water,and Non-Aqueous Coagulation II Random and Radial Preferential Orientations of the Crystal a-Axis

The preferential orientation of the a-axes of poly-p-phenylenebenzobisoxazole (PBO) crystals in PBO fibers made with differential coagulation processes is characterized. Electron diffraction and micro-focus X-ray diffraction were carried out for this purpose. To estimate the alignment quantitatively a two-phase model is proposed and the calculated X-ray diffraction profiles fit well with the measured profiles. Water vapor coagulation at high temperature gave mostly almost random preferential orientation while a non-aqueous coagulation produced radial orientation. The fibers made with hot liquid water coagulation were characterized as a middle form between the limits of radial and random orientations.     

Molecular dynamics computation of clusters in liquid Fe–Al alloy

By means of constant pressure molecular dynamics (MD) simulation technique, a series of simulations of the Fe₅₀Al₅₀ alloy have been carried out. The atoms interact via semi-empirical n-body noncentral potential. The pair correlation functions and the pair analysis technique is applied to reveal the cluster evolution in the process of quick solidification. By using the bond orientation order parameters, we have measured both local and extended orientation symmetries for computer-generated models of dense liquid and glass. A lot of polyhedra in liquid system, for example, icosahedra, are also obtained. In order to test the reliance of the computation results, corresponding X-ray diffraction experiments have been performed on the material.