Polarized neutron reflectometry of the influence of Fe/Si,Fe/FeSi2 and Au/Fe interfaces on the magnetic properties of epitaxial Fe films

The magnetic and structural properties of epitaxial Fe films grown on Si(1 1 1) are investigated by polarized neutron reflectometry (PNR) at room temperature. The influence of different types of interfaces, Fe/Si, Fe/FeSi₂ and Au/Fe on the magnetic properties of Fe films deposited by molecular beam epitaxy onto Si(1 1 1) are characterized. We observe a drastic reduction of the magnetic moment in the entire Fe film deposited directly on the silicon substrate essentially due to strong Si interdiffusion throughout the whole Fe layer thickness. The use of a silicide FeSi₂ template layer stops the interdiffusion and the value of the magnetic moment of the deposited Fe layer is close to its bulk value. We also evidence the asymmetric nature of the interfaces, Si/Fe and Fe/Si interfaces are magnetically very different. Finally, we show that the use of Au leads to an enhancement of the magnetization at the interface.     

Influence of heat treatment on the structure and magnetic properties of the Co/Zr and Co/Hf multilayer amorphous films

The influence of annealing on the structure and magnetic properties of amorphous Co/Zr and Co/Hf multilayer films was studied with particular attention to the dependence of the magnetic properties, thermal stability and crystallization process on layer composition and thickness. The temperature at which crystallization commences increases from 400 to 460 °C as the layer thickness d_Zr or d_Hf increases from 6 to 18 Å, and decreases from 450 to 400 °C as d_Co increases from 12 to 18 Å. Multilayers containing 19–60 at% Zr were studied. The specific magnetization was found to increase even below the temperature at which crystallization commences. Our data are compared with non-multilayer Co–Zr amorphous films and rapidly quenched metallic glasses.     

Study of thickness-dependent magnetic and transport properties of Fe/Al nanostructures

The paper presents magnetic and transport properties of compositionally modulated Fe/Al multilayer structures (MLS), with an overall atomic concentration ratio of Fe:Al = 3:1, 2:1 and 1:1. All MLS show soft ferromagnetic behaviour at room temperature (RT) with an in-plane easy axis of magnetization. In each case, coercivity increases continuously and magnetization decreases with an increase in temperature due to enhancement in the anisotropy as a result of non-uniform and disordered formation of thin intermixed (dead) FeAl layer at the interfaces. The Curie temperature obtained for the MLS is much less than that of bcc Fe but is well above RT. The observed magnetic behaviour is mainly attributed to the formation of different FeAl phases and increase in anti-ferromagnetic interlayer coupling with addition of Al. The formation of these phases is also supported by resistivity results. The results of this research enabled us to understand that by controlling of layers thickness and temperature in multilayer systems, the nanogranular thin films with good resistive and soft magnetic properties can be obtained.     

Investigation of Fe/Al interface as a function of annealing temperature using XPS

This article describes the systemic investigation of the interface chemical and electronic properties of ultrathin Fe/Al multilayer structure (MLS) as a function of annealing temperature. For this purpose electron beam evaporated [Fe/Al]_×15 ML samples have been prepared under ultrahigh vacuum conditions. The chemical and electronic information of the interfaces at different depth has been obtained from XPS technique.The core level study show a gradual change in the nature of the electronic bonding at the interface as a result of annealing. In particular, the MLS annealed at 200 °C and 400 °C clearly show shifts in the binding energy position of Fe-2p_3/2 core line towards higher energy and Al-2p_3/2 core line towards lower energy side as compared to as-deposited sample, suggesting the formation of FeAl alloy phase at the interface. Another important finding with annealing is that the intensity of peak corresponding to pure Al-2p increases and that of Fe-2p decreases as compared to as-deposited case. The increase in intensity of Al-2p core line suggests the migration of Al atoms towards the surface owing to annealing induced inter-diffusion. The corresponding valence band spectra show appreciable changes in the Fe-3d as well as Al-3s density of states due to strong hybridization of sp-d states at the Fermi level as a result of charge transfer and also provide strong evidence for FeAl alloy formation.     

Exchange interaction effect of TbCo/FePt bilayers

Interlayer exchange coupling in dc-magnetron sputtered Tb_29.6Co_70.4/FePt bilayers with different annealing temperatures of the FePt film have been investigated. The dependence of ordering degree on perpendicular magnetic properties of the FePt film was studied. The Tb_29.6Co_70.4/FePt film has high perpendicular coercivity and high saturated magnetization about 7.5 kOe, and 302 emu/cm³, respectively as the substrate temperature is 500 °C and annealing at 500 °C for 30 min. It also shows a strong exchange coupling between this FePt layer and Tb_29.6Co_70.4 layer. We also examined the interface wall energy in the exchange coupled Tb_29.6Co_70.4/FePt double layers.     

Magnetic property and magnetoresistance in Fe/ITO multilayers

Giant magnetoresistance was found in DC magnetron sputtering Fe/ITO multilayers. The magnetic properties, electrical properties and magnetoresistance were investigated. A critical temperature is found around 50 K where the temperature dependence of resistivity and magnetoresistance ratio exhibit an abruptly change. The temperature dependence of resistance is found to obey Mott's 1/4 law for low temperature. The max magnetoresistance ratio of 2.0% and 6.7% is found at room temperature and 12.5 K, respectively. The increase of magnetoresistance ratio at low temperature is due to the decrease of spin-mixing effect.     

Influence of alloying additions and annealing time on magnetic properties in amorphous alloys based on iron

The present paper focuses on the influence of alloying additions on magnetostriction coefficient, concentration of free volume and magnetization in Fe–X–Si–B, and Fe–X–Cu–Si–B amorphous alloys. It was shown that in one group of alloys, the enhancement of soft magnetic properties effect can be attributed to formation of nanocrystalline phase αFe(Si), a decrease of the magnetostriction coefficient and annealing out of free volume. In the second group of alloys, this effect is due to a decrease of the magnetostriction coefficient and annealing out of free volume i.e. takes place in the relaxed amorphous phase.     

Effect of Cr on the magnetic properties of evaporated CoxCr1−x/Si(1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si(1 0 0) and glass substrates. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Alternating gradient field magnetometer (AGFM) measurements provided saturation magnetization values ranging from 220 to 1200 emu/cm³. Values of squareness exceeding 0.8 have been measured. Coercive field may reach values up to 700 Oe, depending on the percentage of chromium, as well as the substrate nature and the direction of the applied magnetic field. The saturation magnetization value decreases as the Cr content increases. In order to study their dynamical magnetic properties, Brillouin Light Scattering (BLS) measurements have been performed on these samples. Stiffness constant value and anisotropy magnetic field were adjusted to fit the experimental BLS spectra. These results are analyzed and correlated.     

Co-sheathed SiOx nanowires

We fabricated Co-coated SiO_x nanowires and investigated the effects of thermal annealing on their properties. The sputtering process resulted in the formation of a relatively smooth Co shell layer, whereas subsequent thermal annealing generated the Co₃O₄ phase. The photoluminescence (PL) spectrum was not changed by the Co-coating, whereas the thermal annealing induced new peaks in the yellow and ultraviolet regions. Possible emission mechanisms were discussed. Based on the magnetization measurements of the SiO_x-core/Co-shell nanowires, we obtained small and negligible hysteresis loops for the as-fabricated and thermal annealed samples, respectively.     

Structural and magnetic properties of evaporated Fe thin films on Si(1 1 1), Si(1 0 0) and glass substrates

We present experimental results on the structural and magnetic properties of series of Fe thin films evaporated onto Si(1 1 1), Si(1 0 0) and glass substrates. The Fe thickness, t, ranges from 6 to110 nm. X-ray diffraction (XRD) and atomic force microscopy (AFM) have been used to study the structure and surface morphology of these films. The magnetic properties were investigated by means of the Brillouin light scattering (BLS) and magnetic force microscopy (MFM) techniques. The Fe films grow with (1 1 0) texture; as t increases, this (1 1 0) texture becomes weaker for Fe/Si, while for Fe/glass, the texture changes from (1 1 0) to (2 1 1). Grains are larger in Fe/Si than in Fe/glass. The effective magnetization, 4πM_eff, inferred from BLS was found to be lower than the 4πM_S bulk value. Stress induced anisotropy might be in part responsible for this difference. MFM images reveal stripe domain structure for the 110 nm thick Fe/Si(1 0 0) only.     

Magnetic transition in Co/(Gd–Co) multilayers

[Co/Gd_0.36Co_0.64]₄/Co multilayers with Co termination layer have been prepared by rf sputtering. They form macroscopic ferrimagnets with a compensation temperature (T_comp) determined by the thickness ratio of the layers. In low fields the magnetization of Co and Gd–Co layers are along the axis of the applied field. Increasing field makes the moments of both the Co and Gd–Co layers deviate from the axis of the field giving rise to a transition into a twisted state. These magnetic transitions were studied by vibrating sample magnetometer (VSM), magneto-optic Kerr effect and magnetoresistance measurements at various temperatures. The nucleation and evolution of surface- and bulk-twisted magnetic states were also observed in these multilayers.     

Magnetic properties of amorphous Ge–Fe thin films

Thin films of Ge_100−xFe_x (x in at%) alloys, fabricated by thermal co-evaporation, have an amorphous structure at compositions x<∼40, although an unidentified crystalline phase with an FCC symmetry also exists at low Fe content. Magnetization versus temperature curves show that saturation magnetization is non-zero (1 to 2.5 emu/cm³) and remains nearly unchanged up to the highest measured temperature of 350 K. Magnetic hysteresis loops at room temperature show a typical ferromagnetic shape, complete saturation occurring by 1–2 kOe. These results may indicate ferromagnetic ordering at room temperature. No definite tendency is observed in the compositional dependence of saturation magnetization.     

Structural,magnetic and Mössbauer spectral studies of nanosize aluminum substituted nickel zinc ferrites

Nanosize aluminum substituted nickel zinc ferrites were prepared through aerosol route and characterized using TEM, XRD, magnetic measurements and Mössbauer spectroscopy. The particle size of as obtained samples was found to be ∼10 nm which increases up to ∼85 nm upon annealing at 1200 °C. The unit cell parameter ‘a’ decreases linearly with concentration of aluminum due to the small ionic radius of aluminum. The saturation magnetization for all the samples after annealing at 1200 °C lies in the range 12.9–72.6 emu/g and decreases linearly with concentration of aluminum. Room temperature Mössbauer spectra of all as obtained samples of ferrite compositions exhibited a broad doublet suggesting super paramagnetic nature. This doublet is further resolved into two doublets and assigned to the surface region and internal region atoms of the particles. The samples annealed at 1200 °C show broad sextets, which were fitted with five sextets, indicating different local environment of both tetrahedrally and octahedrally coordinated Fe cation.     

Half Ca-doped LaMnO3 films on (0 0 1) SLAO and STO substrate studied by magnetization and transport measurements

In this study, La_0.5Ca_0.5MnO₃ (LCMO) films, at the boundary between ferromagnetic metallic and charge-ordered antiferromagnetic insulator according to the bulk phase diagram, were epitaxially grown on (0 0 1) SrTiO₃ (STO) and SrLaAlO₄ (SLAO) substrates by pulsed laser deposition technique. The films were analyzed by X-ray diffraction, magnetization and magnetoresistance measurements. A considerably higher magnetization was measured for 290-nm-thick film on SLAO substrate compared to the film on STO substrate, although both films have the same chemical composition, thickness and epitaxial orientation. The film on SLAO shows a metal-insulator (MI) transition, which occurs at higher temperatures with increasing applied magnetic field, whereas only insulating behavior was observed for the 290-nm-thick film on STO except for the highest applied magnetic field (7 T). In addition, transport measurements were performed and analyzed by Mott's variable range hopping (VRH) model to correlate the resistivity of the films with the Jahn-Teller strain (ε_J−T) in the structure.     

Study of electronic structures for Fe thin films deposited on Si- and C-faces of 4H-SiC substrates by soft X-ray emission spectroscopy

Silicon carbide (SiC) is a candidate material for electronic devices to operate upon crucial environment. Electronic states of silicides and/or carbide/graphite formed in metal/SiC contact system are fundamentally important from the viewpoint of device performance.We study interface electronic structure of iron thin film deposited on silicon (Si)- and carbon (C)-face of 4H-SiC(0 0 0 1) by using a soft X-ray emission spectroscopy (SXES). For specimens of Fe (50 nm)/4H-SiC (substrate) contact systems annealed at 700 and 900 °C, the Si L_2,3 emission spectra indicate different shapes and peak energies from the substrate depending on thermal-treated temperature. The product of materials such as silicides is suggested. Further, from comparison of Si L_2,3 emission spectra between Si- and C-face for the same annealing temperature at 700 °C, it is concluded that the similar silicides and/or ternary materials are formed on the two surfaces. However for those of 900 °C, the film on substrate is composed of the different silicide and/or ternary materials.     

Effects of thermal annealing on the interband transitions of single and vertically stacked InAs/GaAs self-assembled quantum dots

Photoluminescence (PL) measurements have been carried out to investigate the annealing effects in one-period and three-periods of InAs/GaAs self-assembled quantum dots (QDs) grown on GaAs substrates by using molecular beam epitaxy. After annealing, the PL spectra for the annealed InAs/GaAs QDs showed dramatic blue shifts and significant linewidth narrowing of the PL peaks compared with the as-grown samples. The variations in the PL peak position and the full width at half-maximum of the PL peak are attributed to changes in the composition of the InAs QDs resulting from the interdiffusion between the InAs QDs and the GaAs barrier and to the size homogeneity of the QDs. These results indicate that the optical properties and the crystal qualities of InAs/GaAs QDs are dramatically changed by thermal treatment.     

The influence of substrate temperature and annealing on the properties of pulsed laser-deposited YIG films on fused quartz substrate

Yttrium iron garnet (YIG) thin films were deposited on fused quartz substrate at different substrate temperatures (T_s) varying from room temperature (RT) to 850 °C using pulsed laser deposition (PLD) technique. All the films in the as-deposited state were X-ray amorphous and non-magnetic at RT. The film deposited at RT after annealing at temperatures T_a?700 °C showed both X-ray peaks and the magnetic order. The films deposited at higher T_s (500–850 °C) and then annealed at 700 °C resulted in better-quality films with higher 4πM_s value. The highest value of magnetization was for the sample deposited at 850 °C and annealed at 700 °C, which is 68% of the bulk 4πM_s value.     

Metal contacts to n-GaN

Al, Au, Ti/Al and Ti/Au contacts were prepared on n-GaN and annealed up to 900 °C. The structure, phase and morphology were studied by cross-sectional transmission and scanning electron microscopy as well as by X-ray diffraction (XRD), the electrical behaviour by current-voltage measurements. It was obtained that annealing resulted in interdiffusion, lateral diffusion along the surface, alloying and bowling up of the metal layers. The current-voltage characteristics of as-deposited Al and Ti/Al contacts were linear, while the Au and Ti/Au contacts exhibited rectifying behaviour. Except the Ti/Au contact which became linear, the contacts degraded during heat treatment at 900 °C. The surface of Au and Ti/Au contacts annealed at 900 °C have shown fractal-like structures revealed by scanning electron microscopy. Transmission electron microscopy and XRD investigations of the Ti/Au contact revealed that Au diffused into the n-GaN layer at 900 °C. X-ray diffraction examinations showed, that new Ti₂N, Au₂Ga and Ga₃Ti₂ interface phases formed in Ti/Au contact at 900 °C, new Ti₂N phase formed in Ti/Al contact at 700 and 900 °C, as well as new AlN interface phase developed in Ti/Al contact at 900 °C.     

Optical properties of high-Al-content crack free AlxGa1−xN (x<0.67) films grown on Si(111) by molecular-beam epitaxy

We report on the optical properties of high-Al-content crack free Al_xGa_1−xN (x<0.67) films grown by molecular-beam epitaxy on Si(111) substrates using ammonia as nitrogen source. The energetic position of the A free exciton as a function of the Al content is determined from photoluminescence and reflectivity measurements at low temperature. A bowing parameter of b=1 eV is deduced from these measurements. The excitonic linewidth increases as a function of Al concentration. The observed variation agrees very well with the one calculated using a model in which the broadening effect is assumed to be due to alloy compositional disordering.     

XPS and thermomagnetic characterization of the CeNi4Cr compound

The magnetic, thermodynamic and electronic structure properties are discussed for the CeNi₄Cr compound. The X-ray photoemission spectra (XPS) provide an evidence of a mixed valence behavior with the occupancy of the f states n_f=0.89 and their hybridization with the conduction electrons Δ=30 meV. These values reproduce well the magnetic susceptibility χ(T=0), which is enhanced compared to similar CeNi₄M (M=Al, B, Cu) compounds. In combination with a slightly increased electronic specific heat coefficient (up to 100 mJ mol⁻¹ K⁻²), this compound can be classified as being on the border of the heavy fermion and mixed valence behavior. Using a small magnetic field in the χ(T) measurements reveals a presence of magnetically ordered impurity phase, which is easily damped by higher fields and it is shown that the contribution of this phase is minor. The question of the dependence of the electronic specific heat coefficient on the magnetic field is also addressed and the observations agree well with theoretical predictions based on the Anderson model.