Determination of tin and titanium in soils, sediments and sludges using electrothermal atomic absorption spectrometry with slurry sample introduction

Fast-heating programmes for determining titanium and tin in soils, sediments and sludges using electrothermal atomic absorption spectrometry (ETAAS) with slurry sampling are developed. For titanium determination, suspensions are prepared by weighing 5-40 mg of sample and adding 25 ml of a solution containing 50% (v/v) concentrated hydrofluoric acid. For tin determination, suspensions are prepared by weighing up to 300 mg of sample and then adding 1 ml of a solution containing 25% (v/v) concentrated hydrofluoric acid. Palladium (30 μg) and ammonium dihydrogen phosphate (7% w/v) are used as matrix modifiers for titanium and tin, respectively. Prior mild heating in a microwave oven is recommended for titanium determination. Calibration is carried out using aqueous standards. The tin and titanium contents of a number of samples obtained by using the slurry approach agree with those obtained by means of a procedure based on the total dissolution of the samples using microwave oven digestion. The reliability of the procedures is also confirmed by analysing several certified reference materials.     

Microwave-assisted digestion procedures for biological samples with diluted nitric acid: Identification of reaction products

Microwave-assisted sample preparation using diluted nitric acid solutions is an alternative procedure for digesting organic samples. The efficiency of this procedure depends on the chemical properties of the samples and in this work it was evaluated by the determination of crude protein amount, fat and original carbon. Soybeans grains, bovine blood, bovine muscle and bovine viscera were digested in a cavity-microwave oven using oxidant mixtures in different acid concentrations. The digestion efficiency was evaluated based on the determination of residual carbon content and element recoveries using inductively coupled plasma optical emission spectrometry (ICP OES). In order to determine the main residual organic compounds, the digests were characterized by nuclear magnetic resonance (¹H NMR). Subsequently, studies concerning separation of nitrobenzoic acid isomers were performed by ion pair reversed phase liquid chromatography using a C18 stationary phase, water:acetonitrile:methanol (75:20:5, v/v/v) + 0.05% (v/v) TFA as mobile phase and ultraviolet detection at 254 nm. Sample preparation based on diluted acids proved to be feasible and a recommendable alternative for organic sample digestion, reducing both the reagent volumes and the variability of the residues as a result of the process of decomposition. It was shown that biological matrices containing amino acids, proteins and lipids in their composition produced nitrobenzoic acid isomers and other organic compounds after cleavage of chemical bonds.     

Ultrasound assisted pseudo-digestion of street dust samples prior to determination by atomic absorption spectrometry

A sample preparation method based on ultrasound assisted pseudo-digestion of Pb, Cu, Zn and Ni from street dust samples under ultrasonic effect has been described. Parameters influencing pseudo-digestion, such as sonication time, sample mass, particle size and solvent system were fully optimized. Final solutions obtained upon sonication were analyzed by atomic absorption spectrometry. The best conditions for metal pseudo-digestion were as follows: a 25 min sonication time, a 0.3 g sample mass (in 25 ml solvent), a particle size <63 μm and a mixture of concentrated HNO₃-HClO₄-HF (2:1:1, v/v/v). Analytical results for the four metals by ultrasound assisted pseudo-digestion, acid bomb and conventional wet digestion methods showed a good agreement, thus indicating the possibility of using mild conditions for sample preparation instead of intensive treatments inherent with the digestion methods. In addition, this method reduces the time required for all treatments (pseudo-digestion or digestion, heating to dryness, cooling and separation) with acid bomb and conventional wet digestion methods approximately from 9 to 1 h. The accuracy of the method was tested either by comparing obtained results with those of acid bomb and conventional wet digestion methods or by application on two standard reference materials. The average relative standard deviation of ultrasound assisted pseudo-digestion method varied between 0.9 and 1.8% for N = 12, depending on the analyte.     

LC determination of biopterin reduced forms by UV-photogeneration of biopterin and fluorimetric detection

An off-line photoirradiation LC fluorimetric method to determine tetrahydrobiopterin (BH₄), by photogeneration of biopterin (BIO), is described, as an alternative way to the chemical oxidation procedure. To minimize the uncontrolled BH₄ oxidation, due to environmental oxygen, an antioxidant, dithiothreitol (DTT), was used. The acidity of the medium, as well as the presence of hydrogen peroxide, affects the rate of the photoreaction and the nature of the obtained fluorescent photoproducts. The best conditions were achieved by irradiation in hydrochloric acid (0.2 M) medium, in presence of 100 mM hydrogen peroxide, and using an irradiation time of 20 min. The method was tested in the analysis of serum samples containing BH₄, and recoveries between 89 and 105% were found. Also, the proposed method allows the resolution of BH₄ and BIO, in the same sample, by injection of non-irradiated and irradiated sample aliquots in the chromatographic system.     

Room temperature acid sonication ICP-MS multielemental analysis of milk

Room temperature acid sonication of milk samples is proposed as a fast alternative methodology for the determination of the total content of 45 elements (Li, Al, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Y, Mo, Ag, Cd, In, Sn, U, Sb, Te, Cs, Ba, Hg, Pb, Bi, Th, La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm, Yb, Lu, Hf and Ta) in milk by inductively coupled plasma mass spectrometry (ICP-MS). The aforementioned procedure involves a 10 min sample pre-treatment. Measurements were made in quantitative and semiquantitative (Totalquant^®) modes of analysis using Rh as internal standard and Be, Ge, Tb and Re for internal calibration of the equipment in the semiquantitative mode. The selected isotopes were in general the most abundant ones of each element, except in cases where polyatomic or isobaric interferences were detected. Results of total concentrations in 10 liquid and 11 powdered commercially available milk samples were presented. Method validation was performed by measuring a SRM NIST-1549 non-fat milk powder and through the use of recovery experiments. Additionally, the proposed methodology was compared with a method based on a previous microwave-assisted digestion of samples and a direct analysis of 1:4 diluted samples.     

Cold vapour atomic fluorescence determination of mercury in milk by slurry sampling using multicommutation

A highly sensitive mechanized method has been developed for the determination of mercury in milk by atomic fluorescence spectrometry (AFS). Samples were sonicated for 10 min in an ultrasound water bath in the presence of 8% (v/v) aqua regia, 2% (v/v) antifoam A and 1% (m/v) hydroxilamine hydrochloride, and after that, they were treated with 8 mmol l⁻¹ KBr and 1.6 mmol l⁻¹ KBrO₃ in an hydrochloric medium. Atomic fluorescence measurements were made by multicommutation, which provides a fast alternative in quality control analysis, due to the easy treatment of a large number of samples (approximately 70 h⁻¹), and is an environmentally friendly procedure, which involves a waste generation of only 94.5 ml h⁻¹ as compared with the 605 ml h⁻¹ obtained by using continuous AFS measurements. The limit of detection found was 0.011 ng g⁻¹ Hg in the original sample. The method provided a relative standard deviation of 3.4% for five independent analysis of a sample containing 0.30 ng g⁻¹ Hg. To validate the accuracy of the method, a certified reference material NIST-1459 (non-fat milk powder) containing 0.3±0.2 ng g⁻¹ Hg was analysed and a value of 0.27±0.06 ng g⁻¹ Hg was found. A comparison made between data found by the developed procedure and those obtained by microwave-assisted digestion and continuous AFS measurements evidenced a good comparability between these two strategies. Results obtained for commercially available milk samples varied between 0.09 and 0.61 ng g⁻¹ Hg depending on the type of sample and its origin. The confluence of the analytical waste with a 6 mol l⁻¹ NaOH allowed us to reduce the waste generation in a working session from 1 l to 5 g solid residue with a matrix of Fe(OH)₃ which contributes to the deactivation of traces of heavy metals presents in the samples that does not form volatile hydrides.     

Improved determination of selenium in plant and peat samples using hydride generation-atomic fluorescence spectrometry (HG-AFS)

A robust, accurate and sensitive analytical procedure for the determination of Se in plant and peat samples by hydride generation-atomic fluorescence spectrometry (HG-AFS) was developed. Aliquots (200 mg) of dried samples were digested with 3 mL nitric acid and 0.5 mL hydrogen peroxide in closed, pressurized PTFE vessels in a microwave oven at 220 °C. Addition of HBF₄ or HF to the digestion mixture was not required because experiments demonstrated that Se was not hosted in the silicate fraction of the investigated sample matrices. Selenium(VI) was directly reduced to Se(IV) in the undiluted digestion solutions after addition of 3.8 mL of 4 M HCl in a microwave oven at 103 °C for 3 min. Other reduction reagents, such as hydroxylamine hydrochloride or urea, were not necessary to cope with potential interferences from nitrogen oxides that could hamper the reliable determination of Se by HG-AFS. Optimum hydride generation of Se was achieved by using 0.9% NaBH₄ and 4.5 M HCl. A solution detection limit of 11 ng L⁻¹ was obtained under the optimized experimental conditions which corresponds to a method detection limit of 2.8 ng g⁻¹ in solid peat and plant materials. The precision of replicate measurements was better than 3% at Se concentrations of 50 ng L⁻¹. The analytical procedure was critically evaluated by analysing two certified plant reference materials (SRM 1515 Apple Leaves and SRM 1547 Peach Leaves) as well as three peat reference materials. Excellent agreement between the experimental values ranging from 50 ng g⁻¹ to ∼2 μg g⁻¹ and the certified concentrations was obtained.     

Comparison of ultrasound-assisted leaching with conventional and acid bomb digestion for determination of metals in sediment samples

In this paper, a sample preparation method based on ultrasound assisted leaching of Pb, Cu, Zn, Ni and Mn from river and pond sediment samples under ultrasonic effect has been described. Parameters influencing leaching such as sonication time, sample amount, particle size and extractant were fully optimized. Leachatants obtained upon sonication were directly nebulised into an air-acetylene flame for fast metal determination by atomic absorption spectrometry. The best conditions for metal leaching were as follows: a 25 min sonication time, a 0.5 g sample amount (in 25 mL solvent), a particle size < 63 μm and a mixture of concentrated HNO₃-HCIO₄-HF (2:1:1, v/v/v). Analytical results for the five metals by ultrasound-assisted leaching, acid bomb and conventional digestion methods showed a good agreement, thus indicating the possibility of using mild conditions for sample preparation instead of intensive treatments inherent with the digestion methods. In addition, this method reduces the time required for all treatments (leaching or digestion, heating to dryness, cooling and separation) with acid bomb digestion method (from ∼ 8 h to ∼ 1.5 h) and conventional acid digestion method (from ∼ 14 h to ∼ 1.5 h). The accuracy of the method was tested either by comparing obtained results with those of acid bomb and conventional digestion methods or by application on a standard reference materials. The average relative standard deviation of ultrasound assisted leaching method varied between 0.7-1.9% for N = 6, depending on the analyte.     

Improvement of microwave-assisted digestion of milk powder with diluted nitric acid using oxygen as auxiliary reagent

The feasibility of using diluted HNO₃ solutions under oxygen pressure for decomposition of whole and non-fat milk powders and whey powder samples has been evaluated. Digestion efficiency was evaluated by determining the carbon content in solution (digests) and the determination of Ca, Cd, Cu, Fe, K, Mg, Mn, Mo, Na, Pb and Zn was performed by inductively coupled plasma optical emission spectrometry and Hg by chemical vapor generation coupled to inductively coupled plasma mass spectrometry. Samples (up to 500 mg) were digested using HNO₃ solutions (1 to 14 mol L^− 1) and the effect of oxygen pressure was evaluated between 2.5 and 20 bar. It was possible to perform the digestion of 500 mg of milk powder using 2 mol L^− 1 HNO₃ with oxygen pressure ranging from 7.5 to 20 bar with resultant carbon content in digests lower than 1700 mg L^− 1. Using optimized conditions, less than 0.86 mL of concentrated nitric acid (14 mol L^− 1) was enough to digest 500 mg of sample. The accuracy was evaluated by determination of metal concentrations in certified reference materials, which presented an agreement better than 95% (Student's t test, P < 0.05) for all the analytes.     

Determination of manganese in brain samples by slurry sampling graphite furnace atomic absorption spectrometry

A simple procedure for the determination of manganese in different sections of human brain samples by graphite furnace atomic absorption spectrometry has been developed. Brain sections included cerebellum, hypothalamus, frontal cortex, vermix and encephalic trunk. Two sample preparation procedures were evaluated, namely, slurry sampling and microwave-assisted acid digestion. Brain slurries (2% w/v) could be prepared in distilled, de-ionized water, with good stability for up to 30 min. Brain samples were also digested in a domestic microwave oven using 5 ml of concentrated HNO₃. A mixed palladium+magnesium nitrate chemical modifier was used for thermal stabilization of the analyte in the electrothermal atomizer up to pyrolysis temperatures of 1300 °C, irrespective of the matrix. Quantitation of manganese was conducted in both cases by means of aqueous standards calibration. The detection limits were 0.3 and 0.4 ng ml⁻¹ for the slurry and the digested samples, respectively. The accuracy of the procedure was checked by comparing the results obtained in the analysis of slurries and digested brain samples, and by analysis of the NIST Bovine Liver standard reference material (SRM 1577a). The ease of slurry preparation, together with the conventional set of analytical and instrumental conditions selected for the determination of manganese make such methodology suitable for routine clinical applications.     

Development of a simultaneous extraction and cleanup method for pyrethroid pesticides from indoor house dust samples

An efficient and reliable analytical method was developed for the sensitive and selective quantification of pyrethroid pesticides (PYRs) in house dust samples. The method is based on selective pressurized liquid extraction (SPLE) of the dust-bound PYRs into dichloromethane (DCM) with analysis by gas chromatography/mass spectrometry. Various adsorbents and combinations of extraction solvents and temperatures were evaluated to achieve a high-throughput sample preparation that eliminates the post-extraction cleanup step. The final method used sulfuric acid-impregnated silica (acid silica) and neutral silica together in the extraction cell with the dust sample to provide both extraction and cleanup simultaneously. The optimal ratio of dust/acid silica/silica was 1:0.8:8. The extraction was performed at 2000 psi, at 100 °C with DCM for 5 min in three cycles. Method precision and accuracy were evaluated by the analysis of triplicate aliquots of the dust samples and the samples fortified with the target PYRs. The accuracy measured as the recoveries of the PYRs in the fortified samples ranged from 85% to 120%. The precision measured as the relative standard deviation of replicate samples was within ±25%. The SPLE method was applied to 20 house dust samples collected from households that participated in two field studies regarding exposures to pesticides and other pollutants. Similar concentrations of target PYRs were obtained for the SPLE and a stepwise extraction/cleanup procedure. The SPLE procedure reduces organic solvent consumption and increases the sample throughput when compared with a traditional stepwise extraction and cleanup procedure. This study demonstrates that the SPLE procedure can be applied to complex dust matrices for analysis of PYRs for large scale exposure or environmental monitoring studies.     

Low volume microwave digestion and direct determination of selenium in biological samples by hydride generation-atomic fluorescence spectrometry

A low volume microwave digestion (LVMWD) procedure has been developed to have all forms of selenium (Se) compounds in biological samples decomposed to Se (IV) and allow total Se be directly determined by hydride generation-atomic fluorescence spectrometry (HG-AFS), or voltammetrically. Between 0.3 and 0.4 mL of mixed digestion reagents consisting of concentrated (15.4 M) HNO₃-(18.5 M) H₂SO₄ (v:v = 10:1) and >5 to <40 mg sample were found ideal systems with an optimized MW digestion program. Total Se in five certified reference materials was accurately determined. The results obtained by the conventional and LVMWD techniques agreed well. By avoiding pre-reduction step, this method, suitable for a wide range of biological samples, fully takes the advantages of HG-AFS or voltammetric techniques for their high sensitivity, high tolerance to matrix-related interference and accessibility in instrumentation. LVMWD not only enhances the sample output by 3 times and reduces the operational cost and acid wastes, but also makes the small sample analysis possible for many environmental and medical related research objectives. The digestion pathways of Se containing organic samples are also discussed based on the experimental results.     

Electrothermal atomic absorption spectrometric determination of germanium in soils using ultrasound-assisted leaching

A procedure for determining germanium in soil samples using electrothermal atomic absorption spectrometry is discussed. The analyte is leached from the solid sample by the addition of 1 ml of concentrated hydrofluoric acid to 10-300 mg of sample, and the mixture is then submitted to a 10 min ultrasonic treatment. After adding 0.4 g boric acid and 3 ml concentrated hydrochloric acid, germanium is extracted into 1 ml chloroform and back-extracted into an aqueous phase containing (0.05%, w/v) nickel nitrate. Ten micro liter of aqueous phase are introduced into the atomizer and the analytical signal from germanium is obtained using a fast-heating cycle. The detection limit, calculated using three times the standard error of estimate (s_y/x) of the calibration graph, is 0.015 μg g⁻¹. The reliability of the procedure is verified by analyzing several certified reference materials.     

Neutral persulfate digestion at sub-boiling temperature in an oven for total dissolved phosphorus determination in natural waters

A simplified, easily performed persulfate digestion method has been developed to process a large number of water samples for routine determination of total dissolved phosphorus. A neutral potassium persulfate solution (5%, w/v, pH ∼6.5) is added to the samples (at 10 mg potassium persulfate per mL of sample), which are then digested at 90 °C in an oven for 16 h. This method does not require pH adjustment after digestion because neither an acid nor a base is added to the samples prior to digestion. The full color of phosphoantimonylmolybdenum blue from the digested samples develops within 8 min. Compared with the autoclave method, digestion at sub-boiling temperatures in an oven is safer, and a large number of samples can be heated overnight requiring no constant monitoring. The apparent molar absorptivity (?) of nine organic phosphorus compounds and two condensed inorganic phosphates ranged from 1.17 × 10⁴ to 1.82 × 10⁴ L mol⁻¹ cm⁻¹ in both distilled water and artificial seawater matrixes. The average recovery of these phosphorus compounds was 94 ± 11% for the DIW matrix and 90 ± 12% for the ASW matrix. No significant difference in molar absorptivity was observed between the undigested and digested phosphate, especially in the seawater matrix. It is, therefore, suggested that a phosphate solution be directly employed without digestion as the calibration standard for routine determination of total dissolved phosphorus. This method was used to study the spatial distribution of total dissolved phosphorus in the surface waters of Florida Bay.     

Understanding the process of microwave-assisted digestion combining diluted nitric acid and oxygen as auxiliary reagent

Sample preparation has a long history when thinking about the conversion of solid samples to representative solutions using concentrated acid solutions and high temperature. However, chemical sciences are evolving to cleaner procedures and surely, sample preparation must follow these steps. The advent of microwave-assisted digestion led to new devices that have allowed the development of new procedures based on diluted solutions of nitric acid and more recently the use of oxygen as a reagent. No doubts oxygen has played a major role in most dry and wet digestion procedures for digestion of organic samples, but its role was improved by using it to regenerate nitric acid and consequently decreasing the volumes of acids needed to promote efficient digestions. These aspects were clearly demonstrated by comparing the efficiency of whole milk powder digestions under different pressures of oxygen, atmospheric air or inert argon atmosphere. The pressure profiles in these conditions were also evaluated and indicate the regeneration process. The efficiency of the digestion process using oxygen was demonstrated by measuring residual carbon contents and residual acidity in digests and it was shown that both parameters were fully compatible with requirements of modern instrumental analysis without any further extensive dilution of the digestates.     

Determination of toxic elements in coal by ICP-MS after digestion using microwave-induced combustion

A microwave-induced combustion (MIC) procedure was applied for coal digestion for subsequent determination of As, Cd and Pb by inductively coupled plasma mass spectrometry (ICP-MS) and Hg using cold vapor (CV) generation coupled to ICP-MS. Pellets of coal (500 mg) were combusted using 20 bar of oxygen and ammonium nitrate as aid for ignition. The use of nitric acid as absorbing solution (1.7, 3.5, 5.0, 7.0 and 14 mol L⁻¹) was evaluated. For coal samples with higher ash content, better results were found using 7.0 mol L⁻¹ HNO₃ and an additional reflux step of 5 min after combustion step. For coal samples with ash content lower than 8%, 5.0 mol L⁻¹ nitric acid was suitable to the absorption of all analytes. Accuracy was evaluated using certified reference material (CRM) of coal and spikes. Agreement with certified values and recoveries was better than 95 and 97%, respectively, for all the analytes. For comparison of results, a procedure recommended by the American Society of Testing and Materials (ASTM) was used. Additionally, a conventional microwave-assisted digestion (MAD) in pressurized vessels was also performed. Using ASTM procedure, analyte losses were observed and a relatively long time was necessary for digestion (>6 h). By comparison with MAD procedure, higher sample mass can be digested using MIC allowing better limits of detection. Additionally, the use of concentrated acids was not necessary that is an important aspect in order to obtain low blank levels and lower limits of detection, respectively. The residual carbon content in digests obtained by MAD and MIC was about 15% and <1%, respectively, showing the better digestion efficiency of MIC procedure. Using MIC it was possible to digest completely and simultaneously up to eight samples in only 25 min with relatively lower generation of laboratory effluents.     

Determination of trace impurities in high-purity zirconium dioxide by inductively coupled plasma atomic emission spectrometry using microwave-assisted digestion and wavelet transform-based correction procedure

This paper describes a rapid, accurate and precise method for the determination of trace Fe, Hf, Mn, Na, Si and Ti in high-purity zirconium dioxide (ZrO₂) powders by inductively coupled plasma atomic emission spectrometry (ICP-AES). The samples were dissolved by a microwave-assisted digestion system. Four different digestion programs with various reagents were tested. It was found that using a mixture of sulfuric acid (H₂SO₄) and ammonium sulfate ((NH₄)₂SO₄), the total sample dissolution time was 30 min, much shorter than that required for conventional digestion in an opening system. The determination of almost all of the target analytes suffered from spectral interferences, since Zr shows a line-rich atomic emission spectrometry. The wavelet transform (WT), a recently developed mathematical technique was applied to the correction of spectral interference, and more accurate and precise results were obtained, compared with traditional off-peak background correction procedure. Experimental work revealed that a high Zr concentration would result in a significant decrease in peak height of the analyte lines, which was corrected by standard addition method. The performance of the developed method was evaluated by using synthetic samples. The recoveries were in the range of 87-112% and relative standard deviation was within 1.1-3.4%. The detection limits (3σ) for Fe, Hf, Mn, Na, Si and Ti were found to be 1.2, 13.3, 1.0, 4.5, 5.8 and 2.0 μg g⁻¹, respectively. The results showed that with the microwave-assisted digestion and the WT correction, the detection limits have improved by a factor of about 5 for Fe, 4 for Mn and Ti, 3 for Si, and 2 for Hf and Na, respectively, in comparison with conventional open-system digestion and off-peak correction. The proposed technique was applied to the analysis of trace elements above-mentioned in three types of ZrO₂ powders.     

Rapid on-line sample dissolution assisted by focused microwave radiation for silicate analysis employing flame atomic absorption spectrometry: iron determination

An on-line automated flow injection system with microwave-assisted sample digestion was used to perform silicate rock dissolution in acid medium for iron determination. For this purpose, a continuous flow system was built up by using an automatic flow injection analysis (FIA) system coupled to a flame atomic absorption spectrometer (FAAS), including a focused microwave oven unit. Inside the microwave cavity was inserted a polytetrafluoroethylene (PTFE) reactor coil (300 cm length and 0.8 mm i.d.) where the dissolution takes place. Chemical and flow variables as well as iron determination parameters were studied. In the flow system, a slurry of the rock sample (50 mg in 200 ml of acid mixture HF+HCl+HNO₃) is pumped through the reaction coil and the microwaves are turned on. After elapsed the time required to complete the sample dissolution, the mixture is pumped again in order to fill the sampling loop (500 μl). Then, by changing the valve position, a water carrier stream pushes the sample solution through the flame atomic absorption spectrometer nebulizer. To achieve an accurate determination of the rock certified materials, the slurry sample was irradiated during 210 s at 90 W power. Working in that condition, a detection limit of 0.80 μg ml⁻¹ (which corresponds to an Fe₂O₃ content of 0.46%) and an analytical throughput of 10 h⁻¹ were achieved. The relative standard deviation (R.S.D.) of the method varied between 1 and 11% when applied to the rock certified materials.     

Determination of Trace Iron(II) in the Presence of Iron(III)

The determination of trace iron(II) is usually interfered by the presence of iron(III) when ortho-phenanthroline colorimetric method is used. In this report a chromogenic reagent which contains ortho-phenanthroline-EDTA mixture has been developed to decrease the interference of ferric ion after adjusting the acidity of sample at 0.1 N by adding the sulfuric acid. The procedure is also simplified by introducing sulfamate buffer solution (pH= 1.5) without adjusting the acidity of sample with sulfuric acid. If iron(III) is not present in the sample, this method is also applicable. The comparative results are exhibited for the present method and the conventional o-phenanthroline method.     

Single vessel procedure for acid vapor partial digestion of bovine liver in a focused microwave: multielement determination by ICP-OES

An acid vapor partial digestion procedure for bovine liver is proposed using a focused microwave oven and a laboratory-made PTFE support. The support is equipped with three cups of approximately 4 ml volume each one and the cups were adapted to the glass reaction vessel of the microwave oven. A mixture containing HNO₃ plus H₂SO₄ is heated to 120 °C to generate acid vapor. Bovine liver (50-90 mg) were directly weighed into the cups followed by addition of a mixture containing NaClO+H₂O₂. Samples were exposed to acid vapor during 15-25 min and then diluted with distilled and deionized water to final masses of 3.0 g. Recoveries of Al, Ca, Cu, Fe, Mg, Mn, and Zn were evaluated using an ICP-OES with axially-viewed configuration. The effects of both particle sizes and acid vapor exposure time were evaluated and recoveries of most elements were quantitative when using 25 min of heating and 50 mg of samples. Slightly better recoveries were reached using particles smaller than 44 μm, but this effect was mainly observed for hardly extracted elements such as Al and Fe.