Piezoelectric properties of PbHfO3–PbTiO3–Pb(Mg1/3Nb2/3)O3 ternary ceramics

(1 – x)Pb(Hf_1–yTi_y)O₃–x Pb(Mg_1/3Nb_2/3)O₃ (x = 0.1 ～ 0.25, y = 0.555) ternary piezoelectric ceramics were prepared using the two‐step precursor method. Morphotropic phase boundary (MPB) compositions, located at x = 0.18 ～ 0.22, were confirmed using X‐ray diffraction and by their dielectric, piezoelectric and ferroelectric properties. The optimum dielectric and piezoelectric properties were achieved for the MPB composition 0.8Pb(Hf_0.445Ti_0.555)O₃–0.2Pb(Mg_1/3Nb_2/3)O₃, with dielectric permittivity ε_r, piezoelectric coefficient d₃₃, planar electromechanical coupling k_p and Curie temperature T_C being on the order of 2800, 680 pC/N, 70% and 276 °C, respectively. Of particular significance is that the new ternary ceramics exhibit comparable piezoelectric and electromechanical properties to commercial PZT5H ceramics, but with much improved T_C, showing a potential for applications at elevated temperature. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth of high performance piezoelectric crystal Pb(Zn1/3Nb2/3)O3-PbTiO3 using PbO flux

Novel piezoelectric crystal (1 − x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃ (PZNT) has attracted much attention due to its high piezoelectric properties and potential applications in medical ultrasonic devices, sonar transducers, solid state actuators. However, the applications of PZNT crystals are limited by the lack of a simple and reproducible growth technique. In this work, large size PZNT crystals were grown by the vertical Bridgman method using 50 mol% PbO as a flux. The growth conditions were optimized as mole ratio of raw materials and flux = 1:1, soaking temperature 1150-1200 °C, soaking time 10 h, the lowering rate of the crucible 0.5 mm/h and the temperature gradient near solid-liquid interface about 50 °C/mm. The maximum size of as-grown PZNT crystal was about 60 mm in length. The crystal was oriented and its piezoelectric constant d₃₃ and coupling coefficient k₃₃ were measured over 2000 pC/N and 0.92, respectively.     

Low-temperature property investigation of the lead indium-niobate-lead nickel-niobate solid solution

The complex perovskite solid solution (1−x) Pb(In_1/2Nb_1/2)O₃-(x) Pb(Ni_1/3Nb_2/3)O₃ has been successfully prepared by the Columbite precursor method. The temperature dependencies of the dielectric constant and pyroelectric coefficient were measured between −261 and 200 °C. Relaxor ferroelectric behavior has been noticed in all compositions across the solid solution. The room-temperature electrostrictive coefficient, Q₃₃, was 1.83×10⁻² C²/m⁴ for x=0.10. No room-temperature piezoelectric activity was detected; however, upon cooling to −261 °C the maximum coupling coefficients k_p=29%, k_t=11%, and k₃₃=31% were observed for the composition x=1.00.     

Dielectric and optical behaviors in relaxor ferroelectric Pb(In1/2Nb1/2)1−xTixO3 crystal

Dielectric permittivities (ε′,ε″) have been measured as functions of temperature (140-535 K) and frequency (500 Hz-2.0 MHz) in a (001)-cut Pb(In_1/2Nb_1/2)_0.7Ti_0.3O₃ (PINT30%) single crystal grown by the modified Bridgman method with Pb(Mg_1/3Nb_2/3)_0.71Ti_0.29O₃ (PMNT29%) seed crystal. A diffused phase transition was observed in the temperature region of ∼430-460 K with strong frequency dispersion. Above the Burns temperature T_B≅510 K, the dielectric permittivity was found to follow the Curie-Weiss behavior, ε′=C/(T−T_C), with parameters C=3.9×10⁵ and T_C=472 K. Below T_B≅510 K, polar nanoclusters are considered to appear and are responsible for the diffused dielectric anomaly. Optical transmission, refractive indices, and the Cauchy equations were obtained as a function of wavelength at room temperature. The unpoled crystal shows almost no birefringence, indicating that the average structural symmetry is optically isotropic. The crystal exhibits a broad transparency in the wavelength range of ∼0.4-6.0 μm.     

Electrical properties of high Curie temperature (1−x)Pb(In1/2Nb1/2)O3-xPbTiO3 single crystals grown by the solution Bridgman technique

0.65Pb(In_1/2Nb_1/2)O₃-0.35PbTiO₃ (PINT65/35) (starting composition) single crystals were grown successfully through the solution Bridgman technique using PbO flux and PMNT67/33 seed crystals. Because of the composition variation, the final composition of achievable crystals is in a range of 0.32-0.34 with the corresponding T_c range of 265-269 °C. The (001) plates of as-grown PINT66/34 single crystals show high Curie temperature (T_c=269 °C) and rhombohedral-tetragonal phase transition temperature (T_rt=134 °C). Besides, good electrical properties with high dielectric constant (ε>3000), low dielectric loss (tan δ∼1.2%), high piezoelectric constant (d₃₃∼2000 pC/N) and large electromechanical coupling factor (k_t≈59%) at room temperature have been obtained on the (001) plates. The sound velocity, acoustic impedance and other piezoelectric parameters were also measured on the (001) plates in this study, which provide us more detailed information about PINT66/34 single crystals.     

Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Optical properties of Nb doped SrTiO3 from first principles study

The electronic and optical properties of Nb doped SrTiO₃ are studied by ab initio linear muffin-tin orbital method in the atomic sphere approximation. The equilibrium lattice constants of SrTi_1−xNb_xO₃ with x=0.0, 0.25 and 0.5 are found by minimization of the total energy curves. The computated lattice constants are in good agreement with experimental data. Our electronic band calculation shows that the Fermi level of SrTi_1−xNb_xO₃ with x≥0.125 moves into the conduction bands and the system shows metallic behavior. The numerical results indicate that the Nb impurity atoms would lead to the distortion of the band edges. The complex dielectric function of SrTiO₃ and Nb doped SrTiO₃ are calculated using the random-phase approximation. The doping effect on the optical properties of SrTi_1−xNb_xO₃ is discussed.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Dielectric, piezoelectric and elastic properties of tetragonal BiScO3-PbTiO3 single crystal with single domain

Modified BiScO₃-PbTiO₃ (BSPT) tetragonal single crystals were grown using high temperature solution method. The dielectric, piezoelectric and elastic properties of single domain BSPT crystals, after poling along [001] crystallographic direction, have been determined experimentally using the resonance method. The results showed that the BSPT tetragonal crystals possess good piezoelectric properties, with electromechanical coupling factor about 88% and piezoelectric coefficient over 400 pC/N at room temperature. BSPT tetragonal crystals have high Curie temperature around 436 °C and high coercive field ∼28 kV/cm, also, the crystal exhibited a very good temperature stability of the properties till 380 °C. For comparison, the material constants of tetragonal Pb(Zn_1/3Nb_2/3)O₃-PbTiO₃ (PZNT) single crystals were measured and listed in this paper.     

Electro-optic characterization of tetragonal (1−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals by a modified Sénarmont setup

The refractive indices of tetragonal (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN-xPT) single crystals were measured with a prism coupler and their linear electro-optic (EO) properties were investigated from 20 to 80 °C by the automated scanning Sénarmont system with an ac field. The composition and temperature effect on the EO coefficients were also discussed. It has been found that their EO coefficients are much larger than that of widely used LiNbO₃ single crystal and the calculated half-wave voltages are also much lower, which enable the operation at lower voltages and the smaller device dimensions. Since the excellent EO properties are very stable and such high quality single crystals with large-size have been obtained, the PMN-xPT single crystals are a very promising candidate for EO modulation applications. By linking to the polarization-related quadratic EO coefficients, we find that the linear EO properties are related with the spontaneous polarization and dielectric constants.     

Electromechanical properties and dielectric behavior of (Bi1/2Na1/2)(1−1.5x)BixTiO3 lead-free piezoelectric ceramics

Bismuth doped bismuth sodium titanate ceramics [(Bi_1/2Na_1/2)_(1−1.5x)Bi_xTiO₃, x=0 to 0.06] were prepared, and the resulting effects on the microstructure and dielectric properties were examined. All of the Bi-doped ceramics exhibited a single phase of perovskite structure with rhombohedral symmetry. The poling leakage current was significantly reduced by the doping of Bi, facilitating the poling process of the ceramics. The doping with Bi enhances the piezoelectric properties and increases the dielectric constant and the dielectric loss of the ceramics. At 2 mol% Bi-doping level, the ceramics exhibit a large remanent polarization of 47 μC/cm² and a relatively low coercive field of 71 kV/cm, while their d₃₃ and k_p reach a maximum value of 95 pC/N and 21%, respectively.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

Evolution from relaxor-like dielectric to ferroelectric in Ba[(Fe0.5Nb0.5)1−xTix]O3 solid solutions

Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ (x=0.2,0.4,0.6,0.8,0.85,0.9 and 0.95) solid solutions were synthesized by a standard solid-state reaction technique. X-ray diffraction at room temperature and dielectric characteristics over a broad temperature and frequency range were evaluated systematically. The structure of Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ solid solutions changed from cubic to tetragonal with increasing x. A Debye-like dielectric relaxation following the Arrhenius law similar to that in Ba(Fe_0.5Nb_0.5)O₃ was observed at lower temperature in the composition range 0.2≤x≤0.8, while the relaxor ferroelectric, diffused ferroelectric and normal ferroelectric behavior were observed for x=0.85,0.9 and 0.95, respectively. The process of the evolution of relaxor-like dielectric to ferroelectric suggested the changing from dilute polar micro-domains to polar micro-domains, polar micro/macro-domains and then polar macro-domains in the present ceramics.     

Phase diagram of the relaxor (1−x)Pb(Zn1/3Nb2/3)O3-xPbTiO3 investigated by dielectric and Raman spectroscopies

Lead zinc niobate-lead titanate[(1−x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃] (PZN-PT) crystals with x=4.5% and x=12% have been investigated using dielectric and Raman measurements over a range of temperatures. Above room temperature, dielectric measurements show that both compositions exhibit structural phase transitions according to the phase diagram proposed by Kuwata et al. [Ferroelectrics 387 (1981) 579]. Below room temperature, an anomaly at around 180 K for the x=12% sample is observed, suggesting another phase transition. Raman measurements are used to study all phase transitions.     

Piezoelectric properties of new ternary Bi1/2(Na, Li)1/2TiO3–(Bi1/2K1/2)TiO3–Ba0.85Ca0.15Ti0.90Zr0.10O3 ceramics

0.852[Bi_1/2(Na_1?x Li _x )_1/2]TiO₃?C0.110(Bi_1/2K_1/2)TiO₃?C0.038Ba_0.85Ca_0.15Ti_0.90Zr_0.10O₃ (BNLT?CBKT?CBCTZ-x) new ternary piezoelectric ceramics were fabricated by the conventional solid-state method, and their piezoelectric properties as a function of the Li content were mainly investigated. A?stable solid solution with a single perovskite structure has been formed, and the depolarization temperature (T _d) of these ceramics was identified by using the temperature dependence of the dielectric loss. The T _d value of these ceramics gradually decreases, while the T _m value increases with increasing the Li content. The dielectric constant increases and the dielectric loss decreases with increasing the Li content, and an enhanced piezoelectric behavior of d ₃₃??223 pC/N and k _p??35.2?% has been demonstrated in these ceramics with x=0.06.     

Crystal structure,dielectric and piezoelectric properties of Ta/W codoped Bi3TiNbO9 Aurivillius phase ceramics

Aurivillius phase Bi₃Ti_1−xTa_xNb_1−xW_xO₁₂ high temperature piezoceramics were prepared by a conventional solid state reaction method. The crystal structure, dielectric, electrical conduction and piezoelectric properties were systematically studied. Pure or modified Bi₃TiNbO₉ ceramics revealed the presence of only two-layered Aurivillius phase, indicating that Ta/W doping entered into the B-site of pseudo-perovskite structure and formed solid solutions. The Curie temperature had a strong reliance on the structural distortion. Furthermore, Ta/W dopants act as a donor doping, decrease the number of oxygen vacancies and facilitate the domain wall motion. As a result, Ta/W modifications significantly increase the DC resistivity and piezoelectric properties. Bi₃Ti_0.98Ta_0.02Nb_0.98W_0.02O₁₂ ceramics possess the optimum d₃₃ value (∼12.5 pC/N) together with a high T_C point (∼893 °C). Moreover, the resonance–antiresonance spectra demonstrate that the Ta/W-BTN ceramics are indeed piezoelectric in nature at 600 °C. The d₃₃ value of BTTNW-2 ceramic remains ∼12.2 pC/N after annealing at 700 °C. These factors suggest that the BTTNW-based ceramic is a promising candidate for ultra-high temperature sensor applications.     

Observation of magnetoelectric behavior at room temperature in Pb(FexTi1−x)O3

The co-existence of ferroelectric and ferromagnetic properties at room temperature is very rarely observed. We have been successful in converting ferroelectric PbTiO₃ into a magnetoelectric material by partly substituting Fe at the Ti site. The Pb(Fe_xTi_1−x)O₃ system exhibits ferroelectric and ferromagnetic ordering at room temperature. Even more remarkably, our results demonstrate a coupling between the two order parameters. Hence it could be a futuristic material to provide cost effective and simple path for designing novel electromagnetic devices.     

Electrical properties of neodymium doped CaBi4Ti4O15 ceramics

Neodymium doped bismuth layer structure ferroelectrics (BLSFs) ceramics CaBi_4−xNd_xTi₄O₁₅ (x=0, 0.25, 0.50, 0.75) were prepared by solid-state reaction method. X-ray diffraction pattern showed that single phase was formed when x=0-0.75. The refined lattice parameters showed that a (b) axes decrease at x=0.25 and increase with more Nd³⁺ dopant. The effects of Nd³⁺ doping on the dielectric and ferroelectric properties of CaBi₄Ti₄O₁₅ ceramics are studied. Nd³⁺ dopant decreased the Curie temperature linearly, and the dielectric loss, tan δ, as well. The remnant polarization of Nd³⁺ doped CaBi₄Ti₄O₁₅ ceramics was increased by 80% at x=0.25, while more Nd³⁺ dopant decreased the remnant polarization. CaBi_3.75Nd_0.25Ti₄O₁₅ ceramics had the largest piezoelectric constant d₃₃. The structure and properties of CaBi_4−xNd_xTi₄O₁₅ ceramics showed that Nd³⁺ may occupy different crystal locations when Nd³⁺ content x is less than 0.25 and more than 0.50.     

The effect of Fe and Ru substitution on the superconductivity in MgCNi3

We report the effects of partial substitutions of the VIIIa elements: Fe (3d) and Ru (4d) in the intermetallic perovskite superconductor MgCNi₃. In both the MgCNi_3−xRu_x and MgCNi_3−xFe_x systems, the superconducting critical temperature (T_C) decreases monotonically as x is increased. T_C decreases more slowly in the case of Ru, suggesting that the 3d electrons in Fe are magnetically pair breaking. This is supported by the normal state magnetic susceptibility measurements (χ), which shows that χ increases with Fe and decreases with Ru doping. No ferromagnetism is observed in either system.