Surface segregation of aluminum atoms on Cu-9 at.% Al(1 1 1) studied by Auger electron spectroscopy and low energy electron diffraction

Auger electron spectroscopy (AES) and low energy electron diffraction (LEED) were applied to investigate the segregation of aluminum atoms on a Cu-9 at.% Al(1 1 1) surface. We observed that the Al concentration in the top layer ranged between about 9 and 36 at.% after the sample we used was annealed at different temperatures. The phenomenon of Al atoms segregating on the surfaces was explained well by considering the diffusion length of Al atoms in bulk Cu. LEED measurements showed that R30° structures grew as the concentration of Al atoms increased. The segregation phenomena on surfaces resulted in a stable two-dimensional Cu₆₇Al₃₃ alloy phase in the top layer.     

Photoelectron spectroscopy study of Pb/Ag(1 1 1) in the submonolayer range

The vacuum deposition of Pb onto Ag(1 1 1) gives rise to two different surface structures depending on coverage and deposition temperature. At room temperature (RT), low energy electron diffraction (LEED) reveals a sharp reconstruction completed at 1/3 Pb monolayer (ML). Beyond, a close-packed Pb(1 1 1) incommensurate overlayer develops. At low temperature (LT, ∼100 K) the incommensurate structure is directly observed whatever the coverage, corresponding to the growth of close-packed two-dimensional Pb(1 1 1) islands. Synchrotron radiation Pb 5d core-level spectra clearly demonstrate that in each surface structure all Pb atoms have essentially a unique, but different, environment. This reflects the surface alloy formation between the two immiscible metals in the reconstruction and a clear signature of the de-alloying process at RT beyond 1/3 ML coverage.     

Coadsorption of CO and C6H6 on Co(0 0 0 1)

We have studied the influence of CO on the adsorption of benzene on the Co(0 0 0 1) surface using LEED, XPS, TDS and work function measurements. CO was found to reduce the benzene adsorption, but even at saturation CO exposure no complete blocking was observed. Thermal desorption of the coadsorbed layer featured CO and H₂ peaks indicating partial dehydrogenation of benzene and retaining of the CO bond. Ordered LEED structures were found with all coverages: Pre-adsorption of CO led to patterns already seen for pure carbon monoxide adsorption. Pre-adsorption of benzene showed the known structure of pure benzene also with small CO exposures, but higher CO exposures yielded a mixture of and patterns.     

Stable surface termination on vicinal 6H-SiC(0 0 0 1) surfaces

Ordered nanofacet structures on vicinal 6H-SiC(0 0 0 1) surfaces, consisting of pairs of a (0 0 0 1) basal plane and a facet, are investigated in terms of stable surface stacking of the (0 0 0 1) basal planes. The surface termination of S3 (or S3*), i.e., ABC (or A*C*B*), was suggested by a structural model based on quantized step-bunching, which typically gives a one-unit-cell bunched step configuration at the facet. Here, we evaluate the surface termination at basal planes covered with a layer of silicon oxynitride by means of quantitative low-energy electron diffraction (LEED) analysis combined with scanning tunneling microscopy (STM), and show the validity of the structural model proposed.     

Anomalous adsorption of Cs on Pt(1 1 1)

The adsorption of Cs on Pt(1 1 1) surfaces and its reactivity toward oxygen and iodine for coverages θ_Cs?0.15 is reported. These surfaces show unusual “anomalous” behavior compared to higher coverage surfaces. Similar behavior of K on Pt(1 1 1) was previously suggested to involve incorporation of K into the Pt lattice. Despite the larger size of Cs, similar behavior is reported here. Anomalous adsorption is found for coverages lower than 0.15 ML, at which point there is a change in the slope of the work function. Thermal Desorption Spectroscopy (TDS) shows a high-temperature Cs peak at 1135 K, which involves desorption of Cs⁺ from the surface.The anomalous Cs surfaces and their coadsorption with oxygen and iodine are characterized by Auger Electron Spectroscopy (AES), TDS and Low Electron Energy Diffraction (LEED). Iodine adsorption to saturation on Pt(1 1 1)(anom)-Cs give rise to a sharp LEED pattern and a distinctive work function increase. Adsorbed iodine interacts strongly with the Cs and weakens the Cs-Pt bond, leading to desorption of Cs_xI_y clusters at 560 K. Anomalous Cs increases the oxygen coverage over the coverage of 0.25 ML found on clean Pt. However, the Cs-Pt bond is not significantly affected by coadsorbed oxygen, and when oxygen is desorbed the anomalous cesium remains on the surface.     

Reversible electromigration of thallium adatoms on the Si(1 1 1) surface

By means of low-energy electron diffraction (LEED), we found a reversible structural change of on thallium (Tl) adsorbed Si(1 1 1) surfaces by switching the polarity of applied DC voltage for heating the sample. It was shown in the literature that Tl adatoms are located on the T₄ sites of the bulk-terminated surface both in the (1 × 1) and . It is clarified that the structural change is caused by the electromigration of the Tl adatoms. Tl atoms migrate towards the cathode, being induced by the electric field (10-20 V/cm). We discussed an atomic process of the electromigration.     

Co-induced nano-structures on Si(1 1 1) surface

The interaction of cobalt atoms with silicon (1 1 1) surface has been investigated by means of scanning tunneling microscopy (STM) and low-energy electron diffraction (LEED). Besides the Co silicide islands, we have successfully distinguished two inequivalent Co-induced reconstructions on Si(1 1 1) surface. Our high-resolution STM images provide some structural properties of the two different derived phases. Both of the two phases seem to form islands with single domain. The new findings will help us to understand the early stage of Co silicide formations.     

Theoretical study of CO and Pb adsorption on the Ni(1 1 1) and Ni3Al(1 1 1) surfaces

Adsorption of CO molecules and Pb atoms on the Ni(1 1 1) and Ni₃Al(1 1 1) substrates is studied theoretically within an ab initio density-functional-theory approach. Stable adsorption sites and the corresponding adsorption energies are first determined for stoichiometric surfaces. The three-fold hollow sites (fcc for Pb and hcp for CO) are found most favourable on both substrates. Next, the effect of surface alloying by a substitution of selected topmost substrate atoms by Pb or Ni atoms on the adsorption characteristics is investigated. When the surface Al atoms of the Ni₃Al(1 1 1) substrate are replaced by Ni atoms, the Pb and CO adsorption energies approach those for a pure Ni(1 1 1) substrate. The Pb alloying has a more substantial effect. On the Ni₃Al(1 1 1) substrate, it reduces considerably adsorption energy of CO. On the Ni(1 1 1) substrate, CO binding strengthens slightly upon the formation of the Ni(1 1 1)p(2×2)-Pb surface alloy, whereas it weakens drastically when the Ni(1 1 1)-Pb surface alloy is formed.     

Epitaxial growth of ultra-thin NiO films on Cu(1 1 1)

The very first stages of the growth of NiO on Cu(1 1 1) is examined on a microscopic scale. The paper focuses on the morphological and structural characterization of nanostructures formed in the 0-1 Å thickness range. Ultra-thin NiO films, obtained through evaporation of a Ni rod under an oxygen atmosphere were grown at 550 K. In the early stages of the growth the oxide film morphology shows 10-30 nm large, monolayer high, islands with a partial incorporation of metallic Ni in the first Cu(1 1 1) surface plane. The first layer is formed by an epitaxial atomic layer exhibiting a STM contrast similar to the one observed on adsorbed oxygen on Cu(1 1 0). A NiO cluster nucleation and coalescence mechanism is proposed in order to explain the formation of the second NiO layer. A α-Ni₂O₃ hexagonal phase, or a structural distortion of the NiO(1 1 1)()R30° structure could both explain the complex LEED patterns.     

Reactivity to sulphur of clean and pre-oxidised Cu(1 1 1) surfaces

The reactivity of clean and pre-oxidised Cu(1 1 1) surfaces exposed to sulphur (H₂S) has been studied at room temperature by Auger electron spectroscopy, low energy electron diffraction and scanning tunneling microscopy. On the clean surface, the sulphur-saturated surface structure is dominated by the or so-called “zigzag” superstructure. It is shown that a single orientation domain is favoured by the slight misorientation (∼2°) of the surface with respect to the (1 1 1) plane. Scanning tunneling microscopy measurements also revealed two minority structures. Pre-oxidation was performed by exposure to 1.5 × 10⁴ L of O₂ at 300 °C. Under exposure to H₂S (1 × 10⁻⁷ mbar) at room temperature, the oxygen is totally substituted by sulphur. Once initiated, sulphur adsorption seems to propagate to cover the whole surface on the O-covered surface faster than on the clean Cu(1 1 1). At saturation by adsorbed sulphur, the surface is completely covered by the superstructure of highest coverage. This enhanced uptake of sulphur is assigned to the surface reconstruction of the copper surface induced by the pre-oxidation, causing a stronger reactivity of the Cu atoms released by the decomposition of the oxide.     

Adsorption structure of germanium on the Ru(0 0 0 1) surface

Coverage-dependent adsorption energy of the Ge/Ru(0 0 0 1) growth system and the geometrical distortions of the most stable adsorption structure are investigated through first-principles calculations within density functional theory. A local minimum in adsorption energy is found to be at a Ge coverage of 1/7 monolayer with a Ru(0 0 0 1)- symmetry. Based on this stale superstructure, the scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) images are simulated by means of surface local-density of states (LDOS). The results are consistent well with the STM measurements on the phase for Ge overlayer on Ru(0 0 0 1). From this stimulation, the relations between the STM images and the lattice distortion are also clarified.     

Nanoscopic nickel aluminate spinel (NiAl2O4) formation during NiAl(1 1 1) oxidation

Oxidation of a NiAl(1 1 1) single crystal surface was investigated using high resolution soft X-ray photoelectron spectroscopy (HRSXPS), high resolution scanning electron microscopy (HRSEM), energy dispersive X-ray spectroscopy (EDS), X-ray mapping, and atomic force microscopy (AFM). After repeated oxygen exposure, annealing, and cleaning cycles under ultrahigh vacuum conditions, a new oxide phase in the form of tiny 3-dimensional surface structures was detected. These features are several micrometers long and ∼300 nm high and oriented along low index directions in the plane of the substrate; they have nickel aluminate spinel (NiAl₂O₄) stoichiometry. We propose that repeated cycles of oxygen dosing and annealing of the NiAl(1 1 1) surface leads to oxygen diffusion into the bulk and nucleation of spinel below the surface.     

Ge adsorption on SiC(0 0 0 1): An ab initio study

In this work we have performed an ab initio total energy investigation of the Ge adsorption process on the Si-terminated SiC(0 0 0 1)- and (3 × 3) surfaces. We find that Ge adatoms lying on the topmost sites of the and (3 × 3) surfaces represent the energetically more stable configurations at the initial stage of the Ge adsorption on the SiC(0 0 0 1) surface. The Si → Ge substitutional adsorption processes have been examined as a function of the Si and Ge chemical potentials. Increasing the Ge coverage, we verify that the formation of Ge wetting layer on the surface, and Ge nanocluster on the (3 × 3) surface are the energetically more stable configurations, in accordance with recent experimental findings.     

Surface reconstruction of clean bcc-Fe{1 1 0}: A quasi-hexagonal top-layer with periodic height modulation

Hexagonal-pillar shaped pure Fe single crystal whiskers with six {1 1 0} side planes were obtained by means of chemical vapor deposition. Atomically resolved scanning tunneling microscopy images obtained on the {1 1 0} surface showed a quasi-hexagonal atomic array with mesoscopic-range periodic height modulation of about 1/3 of an atomic step. This height modulation was found to be a result of an interference between the quasi-hexagonal top-layer and the sub-surface bcc-Fe{1 1 0} layer. Unit vectors of the mesoscopic-range modulation turned out to be expressed as , where and are the primitive vectors of the two-dimensional atomic array in the top-layer and those in the sub-surface layer, respectively. The two-dimensional density of atoms in the top-layer is slightly higher by 0.46% than that in the sub-surface layer.     

Adsorption of glycine on a NiAl(1 1 0) alloy surface

The adsorption and desorption of glycine (NH₂CH₂COOH), vacuum deposited on a NiAl(1 1 0) surface, were investigated by means of Auger electron spectroscopy (AES), low energy electron diffraction (LEED), temperature-programmed desorption, work function (Δφ) measurements, and ultraviolet photoelectron spectroscopy (UPS). At 120 K, glycine adsorbs molecularly forming mono- and multilayers predominantly in the zwitterionic state, as evidenced by the UPS results. In contrast, the adsorption at room temperature (310 K) is mainly dissociative in the early stages of exposure, while molecular adsorption occurs only near saturation coverage. There is evidence that this molecularly adsorbed species is in the anionic form (NH₂CH₂COO⁻). Analysis of AES data reveals that upon adsorption glycine attacks the aluminium sites on the surface. On heating part of the monolayer adsorbed at 120 K is converted to the anionic form and at higher temperatures dissociates further before desorption. The temperature-induced dissociation of glycine (<400 K) leads to a series of similar reaction products irrespective of the initial adsorption step at 120 K or at 310 K, leaving finally oxygen, carbon and nitrogen at the surface. AES and LEED measurements indicate that oxygen interacts strongly with the Al component of the surface forming an “oxide”-like Al-O layer.     

Segregation of Sn and Sb in a ternary Cu(1 0 0)SnSb alloy

Surface segregation studies of Sn and Sb in Cu(1 0 0)-0.14 at.% Sn-0.12 at.% Sb ternary alloy, have been done by making use of Auger Electron Spectroscopy. The method of Linear Temperature Ramp (LTR) was employed, whereby the sample was heated and cooled linearly at a constant rate. The positive heating rate showed both a kinetic segregation profile, as well as a narrow equilibrium segregation region, at higher temperatures. The equilibrium segregation profile was extended by cooling the sample. Sn was first to segregate to the surface due to its higher diffusion coefficient, mainly from a smaller activation energy E_Sn. Sb, due to its higher segregation energy, eventually replaced Sn from the surface. The modified Darken model was used to simulate the profile yielding the following segregation parameters: D_o(Sn) = 6.3 × 10⁻⁶ m²/s, D_o(Sb) = 2.8 × 10⁻⁵ m²/s; E_Sn = 175.4 kJ/mol, E_Sb = 186.3 kJ/mol; , ; Ω_Cu-Sn = 3.4 kJ/mol, Ω_Cu-Sb = 15.9 kJ/mol and Ω_Sn-Sb = −5.4 kJ/mol.     

GaN/LiNbO3 (0 0 0 1) interface formation calculated from first-principles

The stable adsorption sites for both Ga and N ions on the ideal and on the reconstructed LiNbO₃ (0 0 0 1) surface are determined by means of first-principle total energy calculations. A single N layer is found to be more strongly bound to the substrate than a single Ga layer. The adsorption of a GaN monolayer on the polar substrate within different orientations is then modeled. On the basis of our results, we propose a microscopic model for the GaN/LiNbO₃ interface. The GaN and LiNbO₃ (0 0 0 1) planes are parallel, but rotated by 30° each other, with in-plane epitaxial relationship [1 0 0]_GaN‖ [1 1  0]_LiNbO3. In this way the (0 0 0 1) plane lattice mismatch between GaN and LiNbO₃ is minimal and equal to 6.9% of the GaN lattice constant. The adsorbed GaN and the underlying LiNbO₃ substrate have parallel c-axes.