Influence of Nb substitution for Fe on the magnetic and magneto-impedance properties of amorphous and annealed Fe76.5−xSi13.5B9Cu1Nbx (x=0–7) ribbons

We report a systematic study of the influence of Nb substitution for Fe on the magnetic properties and magneto-impedance (MI) effect in amorphous and annealed Fe_76.5−xSi_13.5B₉Cu₁Nb_x (x=0, 1, 2, 3, 4, 5, 6, and 7) ribbons. The amorphous ribbons were annealed at different temperatures ranging from 530 to 560 °C in vacuum for different annealing times between 5 and 20 min. We have found that for the as-quenched amorphous ribbons, the substitution of Nb for Fe first increases the saturation magnetization (M_s) and decreases the coercivity (H_c) until x=3, for which the largest M_s∼152 emu/g and the smallest H_c∼1.3 Oe are obtained, then an opposite trend is found for x>3. The largest MI ratio (ΔZ/Z∼38% at f=6 MHz) is achieved in the amorphous ribbon with x=3. A similar trend has been observed for the annealed ribbons. The most desirable magnetic properties (M_s∼156 emu/g and H_c∼1.8 Oe) and the largest MI ratio (ΔZ/Z∼221% at f=6 MHz) are achieved for the x=3 sample annealed at 540 °C for 15 min. A correlation between the microstructure, magnetic properties, and MI effect in the annealed ribbons has been established.     

Magnetic, structural and micro-structural properties of mechanically alloyed nano-structured Fe48Co48V4 powder containing inter-metallic Co3V

The Fe₄₈Co₄₈V₄ alloy was synthesized in a planetary high-energy ball-mill under an argon atmosphere. The structure, microstructure and magnetic properties of the mechanically alloyed powders were investigated by X-ray diffraction, Scanning Electron Microscopy and a Vibration Sample Magnetometer, respectively. During the mechanical alloying of Fe₄₈Co₄₈V₄, inter-metallic Co₃V appears. The lattice parameter decreases up to 55 h of milling time with an oscillation and then increases from 55 to 125 h of milling time. The coercivity increases during the milling treatment from 49 to 58 Oe. The saturation magnetization has some fluctuations during the milling treatment and finally reaches ∼190 emu/g at 125 h.     

Simultaneous variations of microstructure and magnetic properties of Ni58Fe12Zr20B10 nanostructure/amorphous alloy prepared by mechanical alloying

This study aims to evaluate magnetic and micro-structural properties of amorphous/nanocrystalline mechanically alloyed Ni₅₈Fe₁₂Zr₂₀B₁₀ powders with ball-milling time up to 190 h. Structural, micro-structural and thermal evaluations of the milled powders were carried out by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and differential scanning calorimetry (DSC) methods. Magnetic properties were also measured by a vibrating sample magnetometer (VSM) instrument. Results showed that the amorphous phase reached maximum value of 95% and the crystallite size was about 3 nm at the end of the milling. Magnetization saturation (M_s) decreased slightly and coercivity (H_c) reached to the highest value at 72 h of the milling time. At the 190 h of milling, the coercivity and saturation magnetization reached 18 Oe and 20 emu/g, respectively. While, after an appropriate amount of heat treatment, these two variables became approximately 2 Oe and 32 emu/g.     

Influence of milling time on the structural, microstructural and magnetic properties of mechanically alloyed Ni58Fe12Zr10Hf10B10 nanostructured/amorphous powders

This paper investigates structural, microstructural and magnetic properties of amorphous/nanocrystalline Ni₅₈Fe₁₂Zr₁₀Hf₁₀B₁₀ powders prepared by high energy milling. Ball milling of Ni, Fe, Zr, Hf and B leads to alloying of the element powders at 120 h. The results show that at 190 h the amorphous content is at the highest level and the grain size is about 2 nm. The magnetic measurements reveal that the coercivity and the saturation magnetization reach about 20 Oe and 30 emu/g at 190 h and become approximately 5 Oe and 40 emu/g after a suitable heat treatment, respectively.     

Influence of Cr content on structure and magnetic properties of Fe-Si-Al-Cr powders

As a kind of soft magnetic metallic material, flaky FeSiAl powders have been studied and used widely. Transition metal chromium can improve the magnetic properties of FeSiAl. This article prepared Fe₈₅Si_9.5-xAl_5.5Cr_x (x=0, 2, 4, 6 wt%) alloys powders by adding chromium to replace silicon in alloys. The morphology and microstructure of alloys powders were studied, electromagnetic parameters were measured and microwave absorption properties in the frequency range from 0.5 to 18 GHz were analyzed. With the increase of Cr content, α-Fe (Al, Si) superlattice phases appeared in alloys powders, and then disappeared. Excessive Cr precipitated from the alloys when its content reaches 6 wt%. The minimum reflection loss (-20 dB) among the four powders was 2 wt% Cr content at the frequency of 11.5 GHz. The peaks of reflection loss shifted to the low frequency range with increase in Cr content.     

Magnetic and structural studies of mechanically alloyed nanostructured Fe49Co49V2 powders

Nanostructured Fe₄₉Co₄₉V₂ powders were produced by high energy milling at different milling times and then examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The saturation magnetization and coercivity of samples were measured at room temperature by a vibration sample magnetometer (VSM). Structural studies show that as the milling time increases from 0 to 125 h, the average grain size reduces from 130 to about 8-10 nm, while the microstrain increases up to 1.7%. The lattice parameter decreases from 0 to 36 h and then increases up to 125 h. According to the XRD patterns, the formation of intermetallic compound of (Fe, Co)V after about 16 h affects the magnetic properties. The coercivity totally increases up to 61 Oe due to the introduction of microstrain during the milling process. Magnetic measurements reveal that the saturation magnetization has some fluctuations during the milling treatment and finally at 125 h reaches about 180 emu/g     

Heat treatment effects on microstructure and magnetic properties of Mn-Zn ferrite powders

Mn-Zn ferrite powders (Mn_0.5Zn_0.5Fe₂O₄) were prepared by the nitrate-citrate auto-combustion method and subsequently annealed in air or argon. The effects of heat treatment temperature on crystalline phases formation, microstructure and magnetic properties of Mn-Zn ferrite were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning electron microscopy and vibrating sample magnetometer. Ferrites decomposed to Fe₂O₃ and Mn₂O₃ after annealing above 550 °C in air, and had poor magnetic properties. However, Fe₂O₃ and Mn₂O₃ were dissolved after ferrites annealing above 1100 °C. Moreover, the 1200 °C annealed sample showed pure ferrite phase, larger saturation magnetization (M_s=48.15 emu g⁻¹) and lower coercivity (H_c=51 Oe) compared with the auto-combusted ferrite powder (M_s=44.32 emu g⁻¹, H_c=70 Oe). The 600 °C air annealed sample had the largest saturation magnetization (M_s=56.37 emu g⁻¹) and the lowest coercivity (H_c=32 Oe) due to the presence of pure ferrite spinel phase, its microstructure and crystalline size.     

Influence of manganese substitution and annealing temperature on the formation,microstructure and magnetic properties of Mn–Zn ferrites

The effects of annealing temperature and manganese substitution on the formation, microstructure and magnetic properties of Mn_xZn_1−xFe₂O₄ (with x varying from 0.3 to 0.9) through a solid-state method have been investigated. The correlation of the microstructure and the grain size with the magnetic properties of Mn–Zn ferrite powders was also reported. X-ray diffraction (XRD), a scanning electron microscope (SEM) and a vibrating sample magnetometer (VSM) were utilized in order to study the effect of variation of manganese substitution and its impact on crystal structure, crystalline size, microstructure and magnetic properties of the ferrite powders formed. The XRD analysis showed that pure single phases of Mn–Zn ferrites were obtained by increasing the annealing temperature to 1200–1300 °C. Increasing the annealing temperature to ?1300 °C led to abnormal grain growth with inter-granular pores and this led to a decrease in the saturation magnetization. Moreover, an increase in the Mn²⁺ ion substitution up to x=0.8 increased the lattice parameter of the formed powders due to the high ionic radii of the Mn²⁺ ion. Mn–Zn ferrites phases were formed and the positions of peaks were shifted by substituting manganese. The average crystalline size was increased by increasing the annealing temperature and decreased by increasing the substitution by manganese up to 0.8. The average crystalline size was in the range 95–137.3 nm. The saturation magnetization of the Mn–Zn-substituted ferrite powders increased continuously with an increase in the Mn concentration up to 0.8 at annealing temperatures of 1200–1300 °C. Further increase of Mn substitution up to 0.9 led to a decrease of saturation magnetization. The saturation magnetization increased from 17.3 emu/g for the Mn_0.3Zn_0.7Fe₂O₄ phase particles produced to 59.08 emu/g for Mn_0.8Mn_0.2Fe₂O₄ particles.     

Magnetic and magnetoelastic properties of Zn-doped cobalt-ferrites—CoFe2−xZnxO4 (x=0, 0.1, 0.2, and 0.3)

Cobalt-ferrite (CoFe₂O₄) based materials are suitable candidates for magnetomechanical sensor applications owing to a strong sensitivity of their magnetostriction to an applied magnetic field. Zn-doped cobalt-ferrites, with nominal compositions CoFe_2−xZn_xO₄ (x=0–0.3), were synthesized by auto-combustion technique using Co- , Fe- , and Zn-nitrate as precursors. X-ray spectra analysis and Transmission electron microscopy studies revealed that the as-prepared powders were comprised of nano-crystalline (∼25–30 nm) cubic-spinel phase with irregularly-shaped grains morphology along with minor impurity phases. Calcination (800 °C for 3 h) of the precursor followed by sintering (1300 °C for 12 h) resulted in a single phase cubic-spinel structure with average grain size ∼2–4 μm, as revealed from scanning electron micrographs. The magnitude of coercive field decreases from ∼540 Oe for x=0 to 105 Oe for x=0.30. Saturation magnetization initially increases and peaks to ∼87 emu/g for x=0.2 and then decreases. The peak value of magnetostriction monotonically decreases with increasing Zn content in the range 0.0–0.3; however the piezomagnetic coefficient (dλ/dH) reaches a maximum value of 105×10⁻⁹ Oe⁻¹ for x=0.1. The observed variation in piezomagnetic coefficient in the Zn substituted cobalt ferrite is related to the reduced anisotropy of the system. The Zn-doped cobalt-ferrite (x=0.1) having high strain derivative could be a potential material for stress sensor application.     

Influence of Ge on magnetic and structural properties of Joule-heated Co-based ribbons: Giant magnetoimpedance response

Studies of magnetic and structural properties of Fe_3.5Co_66.5Si_12−xGe_xB₁₈ (x=0, 3, and 6) soft magnetic ribbons obtained by melt-spinning were performed. The samples were submitted to Joule-heating treatments with different maximum current values (0.01, 0.05, 0.1, 0.2, and 0.8 A, respectively) with steps of 0.01 A and times by step of 1, 2, and 10 s). X-ray diffraction, temperature dependence of magnetization (for the as-quenched samples), coercivity and giant magnetoimpedance (GMI), measured at different frequencies (100, 500, and 900 kHz, respectively) were performed. All the samples crystallized at annealing currents higher than 0.4 A, which was consistent with the magnetic hardening of the material. Coercivities less than 1 A/m were obtained for the three samples between 0.1 and 0.2 A. Maximum value of GMI response was observed for the sample without Ge in the as-quenched state.     

Stress-MI and domain studies in Co-based nanocrystalline ribbons

A systematic investigation of the influence of different types of annealing on the magnetoimpedance (MI) effect in melt-spun (Co_1−xFe_x)₈₉Zr₇B₄ [x=0, 0.025, 0.05] and (Co_0.88Fe_0.12)_78.4Nb_2.6Si₉B₉Al ribbons has been carried out in the frequency range 500 kHz-13 MHz and under dc magnetic fields (H_dc) up to 80 Oe. In the stress annealed ribbons, the strain-induced transverse anisotropy is seen to result in large MI. Magnetic domains were investigated in the ribbons through magnetic force microscopy.     

Crystal structure and magnetic properties of MnxBi100−x (x=48, 50, 55 and 60) compounds

Mn_xBi_100−x (x=48, 50, 55 and 60) alloys were prepared by the induction melting technique, and subjected to melt spinning and subsequent ball milling. XRD shows that the as-milled powders were mainly composed of LTP MnBi. Increasing melt spinning speed and reducing annealing treatment time can restrain the segregation of Mn from MnBi liquid during the peritectic reaction, which increases the LTP MnBi content. High energy ball milling results in the coercivity increase of MnBi powders. With increasing milling time, the coercivity increases initially and then decreases gradually. After ball milling for 4 h, the coercivity of the Mn_xBi_100−x powders is 11.4 kOe for x=48 and 14.8 kOe for x=55. The optimal composition of Mn₄₈Bi₅₂ with more LTP has an M_2.2 T of 49.98 emu/g and an M_r of 33.57 emu/g.     

Synthesis and characterization of Sr(ZnZr)x Fe12−2xO19-PANI composites

Strontium zinc zirconium hexaferrites/polyaniline (Sr(ZnZr)_xFe_12−2xO₁₉-PANI, x=0, 0.5, 1.0) composites were synthesized by oxidative chemical polymerization of aniline in the presence of ammonium peroxydisulfate (APS). The structure and morphology of the product was characterized by FTIR, TGA and SEM. The particle size of the core material was found to be about 250-500 nm. After coating with polyaniline, the particle size of Sr(ZnZr)_0.5Fe₁₁O₁₉-PANI composites grew upto 0.5-1.0 μm. XRD of the ferrites indicated that the structure of the core materials is hexagonal, with lattice constants around 5.886-5.885 Å. It was found that the saturation magnetization (M_S) and coercivity (H_C) for Sr(ZnZr)_xFe_12−2xO₁₉-PANI composites decreased after polyaniline coating. The composite under applied magnetic field, exhibited ferromagnetic hysteretic loops with high saturation magnetization (M_S=18.9-3.8 emu/g) and coercivity (H_C=3850.0-583.91 Oe).     

Tailoring the exchange bias of Ni/NiO nanogranular samples by the structure control

The exchange bias (EB) effect has been studied in Ni/NiO nanogranular samples obtained by annealing in H₂, at selected temperatures (200≤T_ann≤300 °C), NiO powder previously milled for 5, 10, 20 and 30 h. Both the as-milled NiO powders and the Ni/NiO samples have been analyzed by X-ray diffraction and the exchange bias properties have been investigated in the 5-200 K temperature range. The structure and the composition of the Ni/NiO samples can be satisfactorily controlled during the synthesis procedure by varying both T_ann and the milling time of the precursor NiO powders. In particular, by increasing this last parameter, the mean grain size of the NiO phase reduces down to the final value of 16 nm and the microstrain increases, which is consistent with an enhancement of the structural disorder. The structure of the milled NiO matrix strongly affects the process of nucleation and growth of the Ni nanocrystallites induced by the H₂ treatments, so that, T_ann being equal, the amount and the mean grain size D_Ni of the Ni phase vary substantially in samples having different milling times. Such features of the Ni phase determine the extent of the Ni/NiO interface and consequently the magnitude of the exchange field H_ex: the highest value (∼940 Oe) has been measured at T=5 K in a sample containing ∼7 wt% Ni and with D_Ni=19 nm. However, in Ni/NiO samples with very different structural characteristics and different values of H_ex at T=5 K, the EB effect vanishes at the same temperature (∼200 K) and the same thermal dependence of H_ex is observed. We consider that the evolution of the EB effect with temperature is ultimately determined by the microstructure of the Ni/NiO interface, which cannot be substantially modified by changing the synthesis parameters, milling time and T_ann.     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.     

Synthesis and magnetic properties of Au-coated amorphous Fe20Ni80 nanoparticles

Gold-coated nanoparticles of Fe₂₀Ni₈₀ (permalloy) have been synthesized by a microemulsion process. The as-prepared samples consist of ∼5 nm diameter particles of amorphous Fe₂₀Ni₈₀ that are likely encapsulated in B₂O₃. One or more Fe₂₀Ni₈₀@B₂O₃ particles are subsequently encapsulated in 8-20 nm gold nanospheres, as determined by TEM and X-ray powder diffraction (XRD) line broadening. The gold shells were found to be under expansive strain. Magnetic data confirm the existence of a superparamagnetic phase with a blocking temperature, T_B, of ∼33 K. The saturation magnetization, M_S, of the as-prepared, Au-coated sample is ∼65 emu g⁻¹ at 5 K and ∼16 emu g⁻¹ at 300 K. The coercivity, H_C, is ∼280 Oe at 5 K.     

Effect of Co underlayer on soft magnetic properties and microstructure of FeCo thin films

High saturation magnetization soft magnetic FeCo (=Fe₆₅Co₃₅) films were prepared using a thin Co underlayer. The FeCo/Co films exhibited a well-defined in-plane uniaxial anisotropy with easy axis coercivity (H_ce) of 10 Oe and hard axis coercivity (H_ch) of 3 Oe, and a half reduction of H_c with H_ce=4.8 Oe and H_ch=1.0 Oe was obtained when the composition was adjusted to 25 at% Co. The effective permeability of the films remains flat around 250 to 800 MHz. The saturation magnetostriction was 5.2×10⁻⁵ and the intrinsic stress was 0.8 GPa in FeCo single layer, both were slightly reduced by Co underlayer. The Co underlayer changed the preferred orientation of the FeCo films from (2 0 0) to (1 1 0) but more significantly, reduced the average grain size from ∼74 to ∼8.2 nm. It also reduced the surface roughness from 2.351 to 0.751 nm. The initial stage and interface diffusion properties were examined by TEM and XPS.     

Influence of environment and grain size on magnetic properties of nanocrystalline Mn–Zn ferrite

Nanocrystalline Mn_1−xZn_xFe₂O₄ (0.2?x?0.9) was prepared by mechanical alloying of the concerned oxide precursors and subsequent annealing in air and Ar atmosphere, respectively. Milling and annealing in air produces Zn-ferrites (ZnFe₂O₄) instead of Mn–Zn ferrites as MnO converts to higher oxides at higher oxygen partial pressure and fails to dissolve in the spinel phase. This is confirmed by careful quantitative X-ray diffraction analysis using Rietvelt profile matching and also by the non-saturating paramagnetic nature of the magnetization response with very low saturation level of these spinels milled and annealed in air. On the other hand, single-phase Mn–Zn ferrite results from the identical precursor oxide blend when milling and annealing are carried out under controlled (Ar) atmosphere. The average grain size of the as-milled and annealed powders, measured by Rietvelt refinement, varies between 6–8 and 14–18 nm, respectively. Further investigations performed with Mn_0.6Zn_0.4Fe₂O₄ reveal that a careful selection of annealing parameters may lead to an early superparamagnetic relaxation. Therefore, the blocking temperature can be significantly reduced through proper heat treatment schedule to ensure superparamagnetism and negligible hysteresis at low temperature.     

Physical and magnetic properties of highly aluminum doped strontium ferrite nanoparticles prepared by auto-combustion route

Highly Al³⁺ ion doped nanocrystalline SrFe_12−xAl_xO₁₉ (0≤x≤12), were prepared by the auto-combustion method and heat treated in air at 1100 °C for 12 h. The phase identification of the powders performed using x-ray diffraction show presence of high-purity hexaferrite phase and absence of any secondary phases. With Al³⁺ doping, the lattice parameters decrease due to smaller Al³⁺ ion replacing Fe³⁺ ions. Morphological analysis performed using transmission electron microscope show growth of needle shaped ferrites with high aspect ratio at Al³⁺ ion content exceeding x≥2. Al³⁺ substitution modifies saturation magnetization (M_S) and coercivity (H_C). The room temperature M_S values continuously reduced while H_C value increased to a maximum value of 18,100 Oe at x=4, which is an unprecedented increase (∼321%) in the coercivity as compared to pure Sr-Ferrite. However, at higher Al³⁺ content x>4, a decline in magnetization and coercivity has been observed. The magnetic results indicate that the best results for applications of this ferrite will be obtained with an iron deficiency in the stoichiometric formulation.     

Growth temperature dependence of the hysteretic behavior of Ni0.5Zn0.5Fe2O4 thin films

Herein, a discussion of the effect of deposition temperature on the magnetic behavior of Ni_0.5Zn_0.5Fe₂O₄ thin films. The thin films were grown by r.f. sputtering technique on (1 0 0) MgO single-crystal substrates at deposition temperatures ranging between 400 and 800 °C. The grain boundary microstructure was analyzed via atomic force microscopy (AFM). AFM images show that grain size (φ∼70-112 nm) increases with increasing deposition temperature, according to a diffusion growth model. From magneto-optical Kerr effect (MOKE) measurements at room temperature, coercive fields, H_c, between 37and 131 Oe were measured. The coercive field, H_c, as a function of grain size, reaches a maximum value of 131 Oe for φ ∼93 nm, while the relative saturation magnetization exhibits a minimum value at this grain size. The behaviors observed were interpreted as the existence of a critical size for the transition from single- to multi-domain regime. The saturation magnetization (21 emu/g<M_s<60 emu/g) was employed to quantify the critical magnetic intergranular correlation length (L_c≈166 nm), where a single-grain to coupled-grain behavior transition occurs. Experimental hysteresis loops were fitted by the Jiles-Atherton model (JAM). The value of the k-parameter of the JAM fitted by means of this model (k/μ_o∼50 A m²) was correlated to the domain size from the behavior of k, we observed a maximum in the density of defects for the sample with φ∼93 nm.