FINEMET type alloy without Si: Structural and magnetic properties

Magnetic and structural properties of a Finemet type alloy (Fe_73.5Ge_15.5Nb₃B₇Cu₁) without Si and high Ge content were studied. Amorphous material was obtained by the melt spinning technique and was heat treated at different temperatures for 1 h under high vacuum to induce the nanocrystallization of the sample. The softest magnetic properties were obtained between 673 and 873 K. The role of Ge on the ferromagnetic paramagnetic transition of the as-quenched alloys and its influence on the crystallization process were studied using a calorimetric technique. Mössbauer spectroscopy was employed in the nanocrystallized alloy annealed at 823 K to obtain the composition of the nanocrystals and the amorphous phase fraction. Using this data and magnetic measurements of the as-quenched alloy, the magnetic contribution of nanocrystals to the alloy annealed at 823 K was estimated via a linear model.     

Structural transformations of Fe81B13Si4C2 amorphous alloy induced by heating

Thermal stability and crystallization of the Fe₈₁B₁₂Si₄C₂ alloy were investigated in the temperature range 25-700 °C by the XRD and Mössbauer analysis. It was shown that on heating the as-prepared amorphous Fe₈₁B₁₂Si₄C₂ alloy undergoes thermal stabilization through a series of structural transformations involving the process of stress-relieving (temperature range 200-400 °C), followed by a loss of ferromagnetic properties (Curie temperature at 420 °C) and finally crystallization (temperature range 450-530 °C). The process of crystallization begins by formation of two crystal phases: Fe₃B and subsequently Fe₂B, as well as a solid solution α-Fe(Si). With increase in annealing temperature, the completely crystallized alloy involved only two phases, Fe₂B and solid solution α-Fe(Si).XRD patterns established a difference in phase composition and size of the formed crystallites during crystallization depending on the side (fishy or shiny) of the ribbon. The first nuclei of the phase α-Fe₃Si were found on the shiny side by XRD after heat treatment even at 200 °C but the same phase on the fishy side of ribbon was noticed after heat treatment at 450 °C. The largest difference between the contact and free surface was found for the Fe₂B phase crystallized by heating at 700 °C, showing the largest size of crystallites of about 130 nm at 700 °C on the free (shiny) surface.     

Annealing effect on soft magnetic properties and magnetoimpedance of Finemet Fe73.5Si13.5B9Nb3Au1 alloy

Effect of annealing on the soft magnetic properties of Fe_73.5Si_13.5B₉Nb₃Au₁ amorphous ribbon has been investigated by means of structure examination, magnetoimpedance ratio (MIR) and incremental permeability ratio (PR) spectra measured in the frequency range of 1–10 MHz at a fixed current of 10 mA X-ray diffraction analysis showed that the as-cast sample was amorphous and it became nanocrystalline under a proper heat treatment. When annealing amorphous alloy at 530 °C for 30, 60, 90 min, soft magnetic properties have been improved drastically. Among the samples investigated, the sample annealed at 530 °C for 90 min showed the softest magnetic behavior. The MIR and PR curves revealed the desirable changes in anisotropy field depending upon annealing.     

Mössbauer study of isothermally annealed amorphous Fe-Nb-Cu-Si-B alloys

Amorphous ribbons of Fe_73.5Nb₃Cu₁Si_13.5B₉ have been annealed above the crystallization temperature. Annealed samples consisted of crystalline and amorphous phases in a wide temperature range. Two samples of different thicknesses of 33 µm and 27 µm were isothermally annealed at a temperature of 545°C from 0.5 to 5 h in a vacuum furnace. The amount of crystalline phase increases rapidly in the ticker sample. The crystalline part of the Mössbauer spectrum consists of four sharp sextets which can be assigned to a DO₃-structure FeSi alloy. After 700°C annealing the amorphous phase was not observed and the crystalline phase consisted of the DO₃-structure FeSi alloy, paramagnetic FeNbB and presumably Fe₂₃B₆ and Fe₃SiB₂.     

Effects of annealing temperature on structure and magnetic properties of CoAl0.2Fe1.8O4/SiO2 nanocomposites

CoAl_0.2Fe_1.8O₄/SiO₂ nanocomposites were prepared by sol–gel method. The effects of annealing temperature on the structure and magnetic properties of the samples were studied by X-ray diffraction, transmission electron microscopy, vibrating sample magnetometer and Mössbauer spectroscopy. The results show that the CoAl_0.2Fe_1.8O₄ in the samples exhibits a spinel structure after being annealed. As annealing temperature increases from 800 to 1200 °C, the average grain size of CoAl_0.2Fe_1.8O₄ in the nanocomposites increases from 5 to 41 nm while the lattice constant decreases from 0.8397 to 0.8391 nm, the saturation magnetization increases from 21.96 to 41.53 emu/g. Coercivity reaches a maximum of 1082 Oe for the sample annealed at 1100 °C, and thereafter decreases with further increasing annealing temperature. Mössbauer spectra show that the isomer shift decreases, hyperfine field increases and the samples transfer from mixed state of superparamagnetic and magnetic order to the completely magnetic order with annealing temperature increasing from 800 to 1200 °C.     

Effects of annealing temperature on structure and magnetic properties of amorphous Fe61Co27P12 nanowire arrays

Arrays of Fe₆₁Co₂₇P₁₂ nanowire with an aspect ratio about 70 were prepared in anodic aluminum oxide templates by electrodeposition. The influences of annealing temperature on structure and magnetic properties of Fe₆₁Co₂₇P₁₂ nanowires were studied. When the specimens were annealed below 400 °C, there are no obvious changes in structure except relaxation. With the annealing temperature increasing from 400 to 600 °C, the Fe-Co phase is detected by X-ray diffraction and Mössbauer spectra. The crystalline fraction and hyperfine field can be derived from Mössbauer spectra. The room temperature magnetic hysteresis loops show that the coercivity and squareness of the nanowire arrays in parallel to the wire axis increase with the increasing of annealing temperature, which mainly attributes to the strengthening of anisotropy.     

XRD, HRTEM, magnetic and Mössbauer studies on chemically prepared Fe-doped nanoparticles of cerium oxide

Nanocrystalline samples of Fe-doped cerium oxide (Ce_0.90Fe_0.1O₂) are prepared by sol-gel method. The precursor materials used for the synthesis are ferric nitrate and cerium nitrate. The as-prepared samples is annealed at different temperatures to obtain the sample with different particle sizes. The crystallographic phases of the nanocrystalline materials have been confirmed by X-ray diffractograms (XRD). The sizes of the nanoparticles estimated from the peaks of the XRD patterns using Debye-Scherrer equation are in the range 6-58 nm. Results extracted from the high-resolution transmission electron microscopy (HRTEM) are in agreement with the findings obtained from XRD. The average magnetic susceptibilities of all the samples with different particle sizes are measured in the temperature range 300-14 K. The average susceptibilities of the samples annealed below ∼740 °C show paramagnetic behaviour. The susceptibilities of the samples annealed at and above ∼740 °C sharply decrease at ∼240 K and this sharp transition is quite likely due to the anti-parallel alignment of Fe³⁺ spins and is attributed to Morin transition of α-Fe₂O₃. Mössbauer spectra of the samples annealed at and above ∼740 °C give sextet patterns indicating the presence of exchange interaction among the Fe³⁺ ions of these samples and these sextets are also of typical nature of the α-Fe₂O₃ phase. The Mössbauer spectra of the samples annealed below ∼740 °C are doublets which may be attributed to either superparamagnetic and/or paramagnetic type nanoparticles.     

Structural characterization and magnetoimpedance effect in amorphous and nanocrystalline AlGe-substituted FeSiBNbCu ribbons

Two series of rapidly solidified FINEMET (Fe_73.5Si_13.5B₉Nb₃Cu₁) alloys with and without partial substitution of Al (1.5 at%)/Ge (1 at%) were prepared by melt-spinning technique. The nanocrystallization process was carried out by the heat treatment of the as-spun ribbons at 560 °C for 1 h in a vacuum furnace. X-ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimeter (DSC), Mössbauer spectroscopy, and magnetoimpedance (MI) measurements were conducted on the as-quenched and heat-treated alloys to investigate their structural and magnetic properties. The average crystallite sizes obtained for the heat-treated samples were in the range of 10–12 nm as confirmed by our XRD and TEM data. The ultrasoft magnetic behavior observed for the Al/Ge-substituted nanocrystalline alloys was confirmed both by our magnetic data and magnetoimpedance ratio (MIR%) results. A twofold increase in the magnitude of the MIR% (99%) was observed for the Al/Ge-substituted nanocrystalline alloy against that of the pure FINEMET alloy (∼48%) measured at 5.5 MHz. This is believed to be related to the decrease of the magnetocrystalline anisotropy as well as magnetostriction decline due to the Al substitution for Fe atoms in this nanostructured alloy.     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.     

Microstructure and magnetic properties of bulk amorphous and nanocrystalline Fe61Co10Zr2.5Hf2.5Nb2W2B20 alloy

The microstructure and magnetic properties, i.e. the initial magnetic susceptibility, its disaccommodation, core losses and approach to ferromagnetic saturation of the bulk amorphous and partially crystallized Fe₆₁Co₁₀Zr_2.5Hf_2.5Nb₂W₂B₂₀ alloy are studied. From X-ray, Mössbauer spectroscopy and electron microscopy studies we have stated that all samples in the as-quenched state are fully amorphous. However, after annealing the samples at 850 K for 30 min the crystalline α-FeCo grains embedded in the amorphous matrix are found. Moreover, from Mössbauer spectra analysis we have stated that the crystalline phase in those samples exhibits the long-range order. The alloy in the as-quenched state shows good thermal stability of the initial magnetic susceptibility. Furthermore, the intensity of the magnetic susceptibility disaccommodation in the rod is lower than in the ribbon. It is due to low quenching rate during the rod preparation which involves the reduction of free volumes. From the analysis of the isochronal disaccommodation curves, assuming the Gaussian distribution of relaxation times, we have found that activation energies of the elementary processes responsible for this phenomenon range from 1.2 to 1.4 eV. After the annealing of the samples the initial susceptibility slightly enhances and disaccommodation drastically decreases. From high-field magnetization studies we have learned that the size of structural defects depends on the quenching rate (the shape of the samples) and changes after annealing.     

Radio-frequency induced effects in amorphous and nanocrystalline Fe73.5Cu1Nb3Si13.5B9

The rf collapse and sideband effects are used to study the microstructure of the Fe_73.5Cu₁Nb₃Si_13.5B₉ alloy in the amorphous and nanocrystalline state. Nanocrystalline grains of -Fe(Si) are formed as a result of annealing of the amorphous alloy at 520–570 °C. The results show that the complete rf collapse of magnetic hfs in the Mössbauer spectra occurs only in the amorphous phase. The rf collapse is strongly affected by the onset of the nanocrystalline phase and is suppressed when the Fe₃B and Fe₂B phases are formed. Partial collapse allows us to follow the remaining crystalline fractions during the crystalline process. The rf sidebands disappear due to the formation of nanocrystals because of the vanishing magnetostriction.     

Structural transformations and magnetic properties of Fe60Pt15B25 and Fe60Pt25B15 nanocomposite alloys

Structural and magnetic properties of two rapidly solidified and post-annealed Fe₆₀Pt₁₅B₂₅ and Fe₆₀Pt₂₅B₁₅ alloys are compared. The as-quenched Fe₆₀Pt₁₅B₂₅ ribbon was fully amorphous whereas in the Fe₆₀Pt₂₅B₁₅ alloy the amorphous phase coexists with an fcc FePt disordered solid solution. Differential scanning calorimetry curves of both alloys reveal a single exothermal peak with onset temperatures of 873 and 847 K for Fe₆₀Pt₁₅B₂₅ and Fe₆₀Pt₂₅B₁₅, respectively. Magnetically hard, tetragonal ordered L1₀ FePt and magnetically soft Fe₂B nanocrystalline phases were formed due to the annealing of the alloys, as indicated by X-ray diffraction and Mössbauer spectroscopy measurements. Two-phase behavior was detected in the temperature dependence of magnetization of the annealed samples. A magnetic hardening was observed for all annealed ribbons. Magnetic properties of the annealed alloys, studied by hysteresis loop measurements, were related to the differences in the relative fractions of the hard and soft magnetic phases calculated from Mössbauer spectra. The alloy with 25 at% Pt exhibits better hard magnetic properties (H_c=437 kA/m, M_r/M_s=0.74) than the alloy with smaller Pt content (H_c=270 kA/m, M_r/M_s=0.73) mainly due to the larger abundance of the ordered tetragonal FePt phase.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Influence of temperature annealing on optical properties of SrTiO3/BaTiO3 multilayered films on indium tin oxide

We have prepared SrTiO₃/BaTiO₃ thin films with multilayered structures deposited on indium tin oxide (ITO) coated glass by a sol-gel deposition and heating at 300-650 °C. The optical properties were obtained by UV-vis spectroscopy. The films show a high transmittance (approximately 85%) in the visible region. The optical band gap of the films is tunable in the 3.64-4.19 eV range by varying the annealing temperature. An abrupt decrease towards the bulk band gap value is observed at annealing temperatures above 600 °C. The multilayered film annealed at 650 ° C exhibited the maximum refractive index of 2.09-1.91 in the 450-750 nm wavelength range. The XRD and AFM results indicate that the films annealed above 600 ° C are substantially more crystalline than the films prepared at lower temperatures which were used to change their optical band gap and complex refractive index to an extent that depended on the annealing temperature.     

Nanostructured Fe50Ni50 alloy formed by chemical reduction

A high purity Fe₅₀Ni₅₀ nanometric alloy was synthesized by ultra rapid autocatalytic chemical reduction of the corresponding transition metal ions in an aqueous solution. The ratio of metal concentration in solution is preserved in the precipitated powder alloy and no metal segregation has been detected. The alloy was characterized as a nanostructured chemically disordered taenite phase by X-ray diffraction (XRD) and Mössbauer spectroscopy (MS). Transmission electron microscopy (TEM) showed that the as prepared alloy contained spherical particles with 96 nm mean diameter size. The particles are composed of crystallites (of ∼15 nm size) and a predominant disordered interfacial region. A thermal treatment of 673 K/2 h produced a structural relaxation with a significant narrowing in the XRD and Mössbauer lines with a exothermic flow in the DSC signal and an increase in the crystallite size to 30 nm.     

Structural,magnetic and Mössbauer spectral studies of nanosize aluminum substituted nickel zinc ferrites

Nanosize aluminum substituted nickel zinc ferrites were prepared through aerosol route and characterized using TEM, XRD, magnetic measurements and Mössbauer spectroscopy. The particle size of as obtained samples was found to be ∼10 nm which increases up to ∼85 nm upon annealing at 1200 °C. The unit cell parameter ‘a’ decreases linearly with concentration of aluminum due to the small ionic radius of aluminum. The saturation magnetization for all the samples after annealing at 1200 °C lies in the range 12.9–72.6 emu/g and decreases linearly with concentration of aluminum. Room temperature Mössbauer spectra of all as obtained samples of ferrite compositions exhibited a broad doublet suggesting super paramagnetic nature. This doublet is further resolved into two doublets and assigned to the surface region and internal region atoms of the particles. The samples annealed at 1200 °C show broad sextets, which were fitted with five sextets, indicating different local environment of both tetrahedrally and octahedrally coordinated Fe cation.     

Synthesis, structural, magnetic and optical properties of nanocrystalline ZnFe2O4

Nanocrystalline zinc ferrite (ZnFe₂O₄) is synthesized by high-energy ball-milling after 12 h from a powders mixture of zinc oxide (ZnO) and hematite (α-Fe₂O₃) with balls to powders mass ratio of 20:1. X-ray diffraction, vibrating sample magnetometer (VSM), the Mössbauer spectrometry and photoluminescence (PL) are used to characterize the samples. Rietveld analysis and VSM measurements show that the powder has an average crystallites size of 10 nm and a ferrimagnetic behavior with a saturation magnetization of 30 emu/g. After annealing at 700 °C, the lattice parameter reduces from 8.448 to 8.427 Å and the sample transforms into a superparamagnetic behavior, which was confirmed as well by the room temperature Mössbauer spectrometry. Different mechanisms to explain the obtained results and the correlation between magnetism and structure are discussed. Finally, the broadband visible emission band is observed in the entire PL spectrum and the estimated energy band gap is about 2.13 eV.     

The existence of giant magnetocaloric effect and laminar structure in Fe73.5−xCrxSi13.5B9Nb3Cu1

Amorphous soft magnetic ribbons Fe_73.5−xCr_xSi_13.5B₉Nb₃Cu₁ (x=1–5) have been fabricated by rapid quenching on a single copper wheel. The differential scanning calorimetry (DSC) patterns showed that the crystallization temperature of α-Fe(Si) phase is ranging from 542 to 569 °C, a little higher than that of pure Finemet (x=0). With the same annealing regime, the crystallization volume fraction as well as the particle size of α-Fe(Si) crystallites decreased with increasing Cr amount substituted for Fe in studied samples. Especially, the interesting fact is that the laminar structure of heat-treated ribbons on the surface contacted to copper wheel in the fabricating process has been firstly discovered and explained to be related to the existence of Cr in studied samples. The hysteresis loop measurement indicated that there is the pinning of displacement of domain walls. The giant magnetocaloric effect (GMCE) has been found in amorphous state of the samples. After annealing, the soft magnetic properties of investigated nanocomposite materials are desirably improved.     

Effect of annealing temperature for Si0.8Ge0.2 epitaxial thin films

This study investigates the effect of annealing temperature on the Si_0.8Ge_0.2 epitaxial layers. The Si_0.8Ge_0.2 epitaxial layers were deposited by using ultrahigh vacuum chemical vapor deposition (UHVCVD) with different annealing temperatures (400-1000 °C). Various measurement technologies, including high-resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM) and interfacial adhesion tester, were used to characterize the materials properties of the SiGe epilayers. The experimental results showed that the SiGe epilayers gradually reduced lattice-mismatch to the underlying substrate as annealing temperature increased (from 400 to 800 °C), which resulted from a high temperature enhancing interdiffusion between the epilayers and the underlying substrate. In addition, the average grain size of the SiGe films increased from 53.3 to 58 nm with increasing annealing temperature. The surface roughness in thin film annealed at 800 °C was 0.46 nm. Moreover, the interfacial adhesion strength increased from 476 ± 9 to 578 ± 12 kg/cm² with increasing the annealing temperature.