Effects of Mg,Al Co-doping into Mn site on electrochemical performance of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript>

In order to study the influence of multiple ions doping into single-site on the structure and electrochemical properties of Ni-rich layered-structure cathode material LiNi_0.5Co_0.2Mn_0.3O₂, the coprecipitation of hydroxides was applied to synthesize Mg, Al co-doped cathode material LiNi_0.5Co_0.2Mn_0.3–x Mg_1/2x Al_1/2x O₂ (x = 0.00, 0.01, 0.02, 0.04) in this paper. Morphology and structure, kinetic parameter, impedance and electrochemical performance of the material were respectively characterized by SEM, XRD, CV, EIS and galvanostatic charge/discharge test. The results of comprehensive analysis showed that the properties of material were improved obviously when the amount of doping was 0.02. At this amount of doping, the corresponding material has smaller cation mixing, higher hexagonal ordering of layered-structure, larger Li⁺ ion diffusion coefficients which are 2.444 × 10^–10 and 4.186 × 10^–10 cm² s^–1 for Li+ intercalation and deintercalation respectively, smaller impedance which is 33.93 Ω, higher specific capacity of first-discharge which is 168.01 mA h g^–1 and higher capacity retention rate which is up to 95.06% after 20 cycles at 0.5 C (100 mA g^–1).     

Synthesis and electrochemical performance of the Li-rich cathode material Li<Subscript>1.17</Subscript>Ni<Subscript>0.12</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.58</Subscript>O<Subscript>2</Subscript> for lithium-ion batteries

Lithium-riched cathode material for lithium-ion batteries, Li_1.17Ni_0.12Co_0.13Mn_0.58O₂, was synthesized via crystallization from a solution of metal acetates, followed by a thermal treatment of the material obtained as a powder. The phase, elemental, and granulometric compositions of the material were examined, as well as the morphology of the powder particles obtained. The discharge capacity of the material in relation to the charging voltage was found from the results of electrochemical tests, and endurance tests were performed. The discharge capacity upon 85 charge/discharge cycles at voltages in the range 2.8–4.8 and a current of 0.1C was about 180 mA h g^–1.     

Structural analysis of La-Mg-Ni-based new hydrogen storage alloy

The structural analysis of new hydrogen storage alloys, La₅Mg₂Ni₂₃ and La₃MgNi₁₄, was performed using HRTEM. As a result, these ternary system alloys were found to be mainly composed of stacked RNi₅ (CaCu₅ type) and R₂Ni₄ (Laves type) structure subunits in a superstructure arrangement. La₅Mg₂Ni₂₃ alloy is composed of the primitive cell of three LaNi₅ units and the primitive cell of two La₂Mg₂Ni₄ units. La₃MgNi₁₄ alloy is composed of four LaNi₅ and two La₂Mg₂Ni₄ unit cells.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Structures and hydrogen storage performances of rare earth-Mg-Ni-Mn-based AB<Subscript>2</Subscript>-type alloys applied to Ni-MH battery

The La_1-x Ce _x MgNi_3.5Mn_0.5 (x = 0, 0.1, 0.2, 0.3, 0.4) alloys were fabricated by melt spinning technology. The effects of Ce content and spinning rate on the structures and electrochemical performances of the alloys were investigated systematically. The identification of X-ray diffraction (XRD) and SEM revealed that the experimental alloys consisted of a major phase LaMgNi₄ and a secondary phase LaNi₅. The variations of Ce content and spinning rate obviously changed the phase abundance of the alloys, namely LaMgNi₄ phase increasing and LaNi₅ phase decreasing with the increase of Ce content and spinning rate. The electrochemical test showed that the as-cast and as-spun alloys achieved the maximum discharge capacities just at the first cycling without any activation. With the increase of Ce content and spinning rate, the discharge capacity of the alloys first increased and then decreased, and the electrochemical kinetics of the alloys, involving the high rate discharge ability (HRD), hydrogen diffusion coefficient (D), limiting current density (I _L), and charge transfer rate, had a similar variation trend, whereas their cycle stabilities have shown increasing trend.     

Electochemical characteristics of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>/Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> battery with conducting polymeric binder

Lithium-ion battery based on LiMn₂O₄/Li₄Ti₅O₁₂ materials was assembled for the first time. The cathode and anode of this battery are prepared with the aqueous combined binder poly-3,4-ethylenedioxythiophene: polystyrene sulfonate/carboxymethylcellulose (without polyvinylidene fluoride). The capacity of the LiMn₂O₄/Li₄Ti₅O₁₂ battery was found to be 75 mA h g^–1 at 0.1 C and 55 mA h g^–1 at 1 C. A 95% capacity was retained after 100 charge-discharge cycles. The batteries demonstrated a high Coulombic efficiency close to 100%. Scanning electron microscopy demonstrated that using the conducting binder poly-3,4-ethylenedioxythiophene: polystyrene sulfonate/carboxymethylcellulose provides formation of dense compact layers of electrode materials with good adhesion to the substrate. The electrode structure remains maintained after 100 charge-discharge cycles.     

Electrochemical Hydrogen Storage in Ti1.6V0.4Ni1−xCox Icosahedral Quasicrystalline Alloys

The discovery of the icosahedral phase (i‐phase) in rapidly quenched Ti_1.6V_0.4Ni_1?xCo_x (x=0.02–0.1) alloys is described herein. The i‐phase occurs in a similar amount relative to the coexisting β‐Ti phase. The electron diffraction patterns show the distinct spot anisotropy, indicating that the i‐phase is metastable. The electrochemical hydrogen storage performances of these five alloy electrodes are also reported herein. The hydrogen desorption of nonelectrochemical recombination in the cyclic voltammetric (CV) response exhibits the demand for electrocatalytic activity improvement. A discharge capacity of 261.5 mA h g^?1 was measured in a Ti_1.6V_0.4Ni_0.96Co_0.04 alloy electrode at 30 mA g^?1 and 303 K and it is shown that an appropriate amount of Co element addition would enhance the cycling stability at the expense of high‐rate discharging ability.     

Mg0.9Ti0.1Ni1－xCox (x＝0.05, 0.1, 0.15, 0.2)合金的合成及电化学性能研究

采用机械合金化法合成了Mg_0.9Ti_0.1Ni_1－xCo_x (x＝0.05, 0.1, 0.15, 0.2)系列四元合金, 并对该系列合金的结构和电化学性能等方面进行了研究. 球磨100 h的该系列合金, XRD结果表明, X射线衍射峰均呈现宽化趋势, 基本呈非晶态. 充放电结果表明, 该系列合金具有较好的活化性能, 它们的循环稳定性明显好于MgNi合金, 其中Mg_0.9Ti_0.1Ni_0.8Co_0.2最大放电容量最高, 为427.5 mAh•g^－1. 在充放电循环过程中, Mg在合金表面形成了Mg(OH)₂是合金电极衰减的主要原因. 腐蚀曲线的测试结果表明, Co的添加可以提高合金电极在碱液中的抗腐蚀能力, 从而提高了电极的循环稳定性.     

Nanocrystallization of hydrogen-charged Mg<Subscript>76</Subscript>Ni<Subscript>19</Subscript>Y<Subscript>5</Subscript> amorphous alloy

The crystallization of a hydrogen-charged melt-spun Mg₇₆Ni₁₉Y₅ amorphous alloy was studied in order to understand the influence of hydrogen absorbed on the crystallization kinetics and mechanism. Hydrogenation does not affect the thermal stability, but decreases significantly the enthalpy of crystallization. The glass transition, which is well manifested in the hydrogen-free alloy, is not observed after hydrogen charging. The main crystalline phases in the H-free and H-charged alloys are the same after complete transformation, but with finer microstructure for the hydrogenated samples.Analysis of the crystallization kinetics reveals that during annealing of hydrogen charged Mg₇₆Ni₁₉Y₅ growth of nanocrystals surrounded by amorphous phase takes place just in the beginning of the transformation, followed by grain growth in fully crystallized material, which is the main process.This revised version was published online in November 2005 with corrections to the Cover Date.     

Synthesis and magnetic properties of a new layered oxide La<Subscript>1.5</Subscript>Sr<Subscript>1.5</Subscript>Mn<Subscript>1.25</Subscript>Ni<Subscript>0.75</Subscript>O<Subscript>6.67</Subscript>

A new oxide phase La_1.5Sr_1.5 Mn_1.25Ni_0.75O_{6.67 ± 0.05}, a member of the A_{n + 1} BnO_3n+1(n=2) Rad-dlesden—Popper homologue series, was synthesized, and its structure and magnetic properties characterized. Magnetic anomalies associated with the competition between antiferromagnetic and ferromagnetic orders are observed in the range of the temperatures studied (2-400 K). The ESR spectra of the compound feature the constriction of a magnetic signal and a shift toward g(Mn⁴⁺).     

Electrochemical oxidation and reduction of La<Subscript>4</Subscript>Ni<Subscript>3</Subscript>O<Subscript>10</Subscript> in alkaline media

In this work we used electrochemical polarization for oxidizing and reducing, in a controlled way, the Ruddlesden-Popper phase La₄Ni₃O₁₀. With a careful choice of electrochemical parameters, we were able to obtain samples of La₄Ni₃O_10± never obtained before. The oxygen stoichiometry can range between 9.78 (=–0.22) and 10.12 (=0.12). The oxidized phase, La₄Ni₃O_10.12, was obtained using a galvanostatic mode (I=20 A) and the reduced phase, La₄Ni₃O_9.78, using potentiostatic conditions (E=0.46 V). The evolution of the electrical conductivity has been studied as a function of .     

The structure and electrochemical characteristics of La0.67Mg0.33 (Ni0.8Co0.1Mn0.1) x (x=2.5–5.0) multiphase alloys for nickel-metal hydride batteries

This paper presents results concerning structure and electrochemical characteristics of the La_0.67Mg_0.33 (Ni_0.8Co_0.1Mn_0.1) _x (x=2.5–5.0) alloy. It can be found from the result of the Rietveld analyses that the structures of the alloys change obviously with increasing x from 2.5 to 5.0. The main phase of the alloys with x=2.5–3.5 is LaMg₂Ni₉ phase with a PuNi₃-type rhombohedral structure, but the main phase of the alloys with x=4.0–5.0 is LaNi₅phase with a CaCu₅-type hexagonal structure. Furthermore, the phase ratio, lattice parameter and cell volume of the LaMg₂Ni₉phase and the LaNi₅ phase change with increasing x. The electrochemical studies show that the maximum discharge capacity increases from 214.7 mAh/g (x=2.5) to 391.1 mAh/g (x=3.5) and then decreases to 238.5 mAh/g (x=5.0). As the discharge current density is 1,200 mA/g, the high rate dischargeability (HRD) increases from 51.1% (x=2.5) to 83.7% (x=3.5) and then decreases to 71.6% (x=5.0). Moreover, the exchange current density (I ₀) of the alloy electrodes first increases and then decrease with increasing x from 2.5 to 5.0, which is consistent with the variation of the HRD. The cell volume reduces with increasing x in the alloys, which is detrimental to hydrogen diffusion and accordingly decreases the low-temperature dischargeability of the alloy electrodes.     

The Pr1-xLaxMgNi4-yCoy alloys: Synthesis,structure and hydrogenation properties

The influence of substitution Pr for La and Ni for Co on hydrogen storage properties of Pr_1-xLa_xMgNi_4-yCo_y (х = 0; 0.5, у = 0–3) alloys were studied. The existences of solid solutions have been found. It is shown that the synthesized alloys absorb hydrogen at room temperature and hydrogen pressure 0.1–10 bar. For some of the studied compounds, the formation of hydrides with cubic and orthorhombic structures was found. Hydrogen capacity for Pr_1-xLa_xMgNi_4-yCo_y alloys increases with Co content increasing and reaches 6.6 H/f.u. for PrMgNi₂Co₂. For electrochemical hydrogenation different trend was observed. With increasing of Co content discharge capacity slightly increases only to y = 0.5, and after y > 0.5, decreases. Highest discharge capacity is equal to 305 mА∙h/g for Pr_0.5La_0.5MgNi_3.5Co_0.5, and 268 mА∙h/g for PrMgNi_3.5Co_0.5 at current densities 50 mА/g and 200 mA/g, respectively. Influence of Co and number of activation cycles on HRD value of PrMgNi_4-yCo_y alloys was investigated. Additionally, obtained results of the electrochemical properties were compared with related compounds.     

Al-doped La<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>MnO<Subscript>3</Subscript> as oxide anode for solid oxide fuel cells using dry C<Subscript>3</Subscript>H<Subscript>8</Subscript> fuel

Direct hydrocarbon type solid oxide fuel cells are attractive from simple gas feed process and also high energy conversion efficiency. In this study, La_0.5Sr_0.5MnO₃ (LSM55) perovskite oxide was studied as oxide anode for direct hydrocarbon type solid oxide fuel cell (SOFC). Although reasonable power density like 1 W/cm² and open circuit voltage (OCV) (1.1 V) at 1273 K was exhibited when H₂ was used as fuel, the power density as well as OCV of the cell using LSM55 for anode was significantly decreased when dry C₃H₈ was used for fuel. After power generation measurement, LSM55 phase was decomposed to MnO and La₂MnO₄. Effects of various dopants to Mn site in LSM55 were studied and it was found that partial substitution of Mn in LSM55 with other cation, especially transition metal, is effective for increasing maximum power density. In particular, reasonable high power density can be achieved on the cell using Ni-doped LSM55 for anode. On the other hand, Al substitution is effective for increasing stability against reduction and so, dopant effects of Al were studied in more details for dry C₃H₈ fuel. The power density as well as OCV increased with increasing Al content and the highest power density was achieved at x = 0.4 in La_0.5Sr_0.5Mn_1 ? x Al _x O₃. Among the examined composition, it was found that the cell using La_0.5Sr_0.5Mn_0.6Al_0.4O₃ anode shows the largest power density (0.2 W/cm²) at 1173 K and high OCV (1.01 V) against dry C₃H₈ fuel.     

La<Subscript>1.8</Subscript>Sr<Subscript>0.2</Subscript>Ni<Subscript>0.8</Subscript>M<Subscript>0.2</Subscript>O<Subscript>4</Subscript> (M = Fe,Co, or Cu) Complex Oxides: Synthesis,Structural Characterization,and Dielectric Properties

New solid solutions La_1.8Sr_0.2Ni_0.8M_0.2O₄ (M = Fe, Co, or Cu) have been prepared, and their crystal- chemical characteristics and electric properties studied. The studied materials have been shown to have activation-time conductivity. Structural distortions have been found to affect the dielectric properties of ceramic samples. La_1.8Sr_0.2Ni_0.8M_0.2O₄ is observed to have the greatest distortion of АО₉ coordination polyhedra and a higher dielectric constant.     

Kinetics of phase formation upon the treatment of La<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)<Subscript>3</Subscript> and La<Subscript>2</Subscript>O<Subscript>2</Subscript>SO<Subscript>4</Subscript> in a hydrogen flow

The sequence of phases occurring during treatment of lanthanum sulfate, La₂(SO₄)₃ and lanthanum oxysulfate, La₂O₂SO₄ in a hydrogen flow is established. The temperature ranges in which homogeneous La₂O₂S is produced are revealed: when La₂(SO₄)₃ is a precursor, the range is 770–1220 K; in the case of La₂O₂SO₄, the interval is 950–1220 K. The kinetic curves showing the time dependence of the yield of La₂O₂S is constructed and treated using the Avrami-Erofeev and contracting volume equations. The activation energies of the reactions are determined.     

Microwave-assisted combustion synthesis of nanocrystalline La<Subscript>2</Subscript>Mo<Subscript>2</Subscript>O<Subscript>9</Subscript> oxide-ion conductor and its characterization

Nanocrystalline La₂Mo₂O₉ oxide-ion conductor has been successfully synthesized by microwave-assisted combustion method within a very short time duration using aspartic acid as the newer fuel in a domestic microwave oven. The synthesized nanocrystalline powder showed good sinterability and reached more than 97% of theoretical density even at low temperature of 800 °C for 5 h. The sintered La₂Mo₂O₉ sample exhibited a conductivity of 0.159 S/cm in air at 750 °C.     

La<Subscript>0.1</Subscript>Ca<Subscript>0.9</Subscript>MnO<Subscript>3</Subscript>/Co<Subscript>3</Subscript>O<Subscript>4</Subscript> for oxygen reduction and evolution reactions (ORER) in alkaline electrolyte

Non-precious metal bifunctional catalysts are of great interest for metal–air batteries, electrolysis, and regenerative fuel cell systems due to their performance and cost benefits compared to the Pt group metals (PGM). In this work, metal oxides of La_0.1Ca_0.9MnO₃ and nano Co₃O₄₇ catalyst as bifunctional catalysts were used in oxygen reduction and evolution reactions (ORER). The catalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and N₂ adsorption isotherms. The electrocatalytic activity of the perovskite-type La_0.1Ca_0.9MnO₃ and Co₃O₄ catalysts both as single and mixtures of both were assessed in alkaline solutions at room temperature. Electrocatalyst activity, stability, and electrode kinetics were studied using cyclic voltammetry (CV) and rotating disk electrode (RDE). This study shows that the bifunctional performance of the mixed La_0.1Ca_0.9MnO₃ and nano Co₃O₄ was superior in comparison to either La_0.1Ca_0.9MnO₃ or nano Co₃O₄ alone for ORER_. The improved activity is due to the synergistic effect between the La_0.1Ca_0.9MnO₃ and nano Co₃O₄ structural and surface properties. This work illustrates that hybridization between these two metal oxides results in the excellent bifunctional oxygen redox activity, stability, and cyclability, leading to a cost-effective application in energy conversion and storage, albeit to the cost of higher catalyst loadings.     

Electrochemical behavior of composite cathodes in contact with solid electrolyte La<Subscript>10</Subscript>Ge<Subscript>6</Subscript>O<Subscript>27</Subscript>

The cathodic overvoltage of composite cathodes 50 wt % La_0.8Sr_0.2MnO₃ (LSM) + 50 wt % La₁₀Ge₆O₂₇ (LGO) (further on, LSM-LGO), LSM-SSZ (Zr_0.835Sc_0.165O_2?δ), Ag-Pd-LGO, and Ag-Pd-SSZ in contact with the LGO electrolyte is measured. The temperature dependences of the polarization conductivity and the working-current densities of the same composite cathodes are investigated. The study is performed at 700–900°C. A comparison with the SSZ electrolyte is conducted. The chemical interaction in the LSM-LGO composition is studied. It is demonstrated that the interaction of lanthanum-strontium manganite with lanthanum germanate occurs with the dissolution of the initial phases in one another and with the formation of fresh phases at elevated temperatures. Coefficients of linear thermal expansion of the LGO and SSZ electrolytes and the LSM, LSM-LGO, and LSM-SSZ electrode materials are compared at 40–900°C. Most of the studied electrodes in contact with the LGO electrolyte demonstrate thermomechanical stability and high electrochemical activity.     

Synthesis and characterization of La<Subscript>0.8</Subscript>Sr<Subscript>0.2</Subscript>Co<Subscript>0.5</Subscript>Fe<Subscript>0.5</Subscript>O<Subscript>3±δ</Subscript> nanopowders by microwave assisted sol–gel route

Nano-crystalline La_0.8Sr_0.2Co_0.5Fe_0.5O_3±δ powder has been successfully synthesized by microwave assisted sol–gel (MWSG) method. The decomposition and crystallization behavior of the gel-precursor was studied by Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) analysis. From the result of FT-IR and X-ray diffraction patterns, it is found that a perovskite La_0.8Sr_0.2Co_0.5Fe_0.5O_3±δ was formed by irradiating the precursor at 700 W for 3 min, but the well-crystalline perovskite La_0.8Sr_0.2Co_0.5Fe_0.5O_3±δ was obtained at 700 W for 35 min. Morphological and specific area analysis of the powder were done by transmission electron microscopy (TEM), scanning electron microscope (SEM) and Brunauer–Emmett–Teller (BET). The surface areas measured was 38.9 m²/g and the grain size was ∼23 nm. Electrochemical properties of pure LSCF cathode on YSZ electrolyte at intermediate temperatures were investigated by using AC impedance analyzer, which shows a low area specific resistance (0.077 Ω cm² at 1073 K and 0.672 Ω cm² at 953 K). Moreover, the synthesis period of 20 h usually observed for conventional heating mode is reduced to a few minutes. Thus, the MWSG method is proved to be a novel, extremely facile, time-saving and energy-efficient route to synthesize LSCF powders.