Relationship between the density of supercritical CO_2 + ethanol binary system and its critical properties

The solvent strength and selectivity of supercritical fluids (SCF) can be greatly enhanced by addition of one or two entrainers into the system. The amount of entrainer added is usually less than 5% (mole fraction). However, even with such slight amount, solubility of organic solutes has been observed to increase by several orders magnitude[1]. Therefore, critical pressure and tem-perature data of these supercritical fluid + cosolvent systems are imperative for the reasonable design of effici…     

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

Diffusion of Quinine with Ethanol as a Co-Solvent in Supercritical CO2

This study aims at contributing to quinine extraction using supercritical CO₂ and ethanol as a co-solvent. The diffusion coefficients of quinine in supercritical CO₂ are measured using the Taylor dispersion technique when quinine is pre-dissolved in ethanol. First, the diffusion coefficients of pure ethanol in the supercritical state of CO₂ were investigated in order to get a basis for seeing a relative change in the diffusion coefficient with the addition of quinine. We report measurements of the diffusion coefficients of ethanol in scCO₂ in the temperature range from 304.3 to 343 K and pressures of 9.5, 10 and 12 MPa. Next, the diffusion coefficients of different amounts of quinine dissolved in ethanol and injected into supercritical CO₂ were measured in the same range of temperatures at p = 12 Mpa. At the pressure p = 9.5 MPa, which is close to the critical pressure, the diffusion coefficients were measured at the temperature, T = 343 K, far from the critical value. It was found that the diffusion coefficients are significantly dependent on the amount of quinine in a small range of its content, less than 0.1%. It is quite likely that this behavior is associated with a change in the spatial structure, that is, the formation of clusters or compounds, and a subsequent increase in the molecular weight of the diffusive substance.     

The influence of film thickness and process temperature on <Emphasis Type="Italic">c</Emphasis>-axis orientation of Bi<Subscript>3</Subscript>TiTaO<Subscript>9</Subscript> thin films

Bi-layered ferroelectric Bi₃TiTaO₉ (BTT) thin films with different thickness (ranging from 100 to 400 nm) were successfully fabricated on Pt(111)/TiO₂/SiO₂/(100)Si substrates using chemical solution deposition (CSD) technique at different annealing temperatures. The c-axis orientation of the films was affected by film thickness and process temperature. The thinner the film and the higher the process temperature, the higher the c-axis orientation. With the increase of film thickness, the stress decreased but the film roughness increased, which led to the decrease of c-axis orientation of films. BTT films annealed at 800°C were found to have much improved remament polarization (P _r ) than that of films annealed at 650 and 750°C. The P _r and coercive field (E _c ) values were measured to be 2 μC/cm² and 100 kV/cm, respectively. BTT films showed well-defined ferroelectric properties with grain size larger than 100 nm.     

Sol-gel processing of lead-free (Na,K)NbO<Subscript>3</Subscript> ferroelectric films

The sol-gel processing of lead-free (Na,K) NbO₃ ferroelectric films was studied. Sodium ethoxide (NaOC₂H₅) and potassium ethoxide (KOC₂H₅) were prepared by reacting solid Na and K with ethanol (99.7%) in a solvent of 2-methoxyethanol. 0.5-μm-thick (Na,K)NbO₃ thin films with orthorhombic perovskite structure were obtained by pyrolyzing at 400°C and annealing at 800–900°C. The films had relatively dense and uniform microstructure with grain size of about 50 nm, whose ferroelectricity was proved by the P-E hysteresis loop measurement. It was found that excess K was effective to reduce the annealing temperature for the crystallization of sol-gel-derived (Na,K)NbO₃ thin films.     

Voltammetric determination of the trace amounts of bromate in drinking water after pre-concentration on hydrous γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

A differential pulse voltammetric (DPV) method for the determination of bromate in drinking water, after pre-concentration on γ-Al₂O₃, is proposed. The reduction peak of bromate has been observed at the potential E _p -−1.6 V in an ammonia buffer as a supporting electrolyte. The method has been successfully applied to determine a bromate concentration of 2.5 μg·l⁻¹ in drinking water (RSD=6.1%, n=7). A sample pre-treatment with a column filled with mixed cation-exchange resin in Ag, Ba and H forms was needed before pre-concentration of bromate on alumina.     

Formation and properties of the Fe<Subscript>8</Subscript>V<Subscript>10</Subscript>W<Subscript>16–x</Subscript>Mo<Subscript>x</Subscript>O<Subscript>85</Subscript> type solid solution

Solid solution phases of a formula Fe₈V₁₀W_16–xMo_xO₈₅ where 0≤x≤4, have been obtained, possessing a structure of the compound Fe₈V₁₀W₁₆O₈₅. It was found on the base of XRD and DTA investigations that these solution phases melted incongruently, with increasing the value of x, in the temperature range from 1108 (x=0) to 1083 K (x=4) depositing Fe₂WO₆ and WO₃. The increase of the Mo⁶⁺ ions content in the crystal lattice of Fe₈V₁₀W₁₆O₈₅ causes the lattice parameters a=b contraction with cbeing almost constant. IR spectra of the Fe₈V₁₀W_16–xMo_xO₈₅ solid solution phases have been recorded.     

Convenient synthesis of microspheres by self-assembly of random copolymers in supercritical carbon dioxide

A novel and convenient synthesis of microspheres was attained by molecular self-assembly of random copolymers in supercritical carbon dioxide. Poly{2-(perfluorooctyl)ethyl acrylate-ran-2-(dimethylamino)ethyl acrylate} random copolymers (P[POA-r-DAA]), with 7:3, 8:2, and 9:1 as the molar ratios of 2-(perfluorooctyl)ethyl acrylate (POA)/2-(dimethylamino)ethyl acrylate (DAA), were soluble in supercritical CO₂ and had their cloud points at about 75 bar higher than the critical pressure of CO₂. The CO₂ density at the cloud points decreased with an increase in temperature. Although the copolymers made a slight difference in the cloud point in the absence of perfluoroazelaic acid (PA), they made a marked difference in the presence of PA. The copolymer with a lower DAA content had a cloud point at lower CO₂ density. The scanning electron microscopy observation demonstrated that the copolymers produced microspheres in the presence of PA at 0.5 as PA/DAA in the heterogeneous state below the cloud points. The microspheres were unstable to pressure and changed to unspecific forms as a result of increasing the CO₂ pressure, although the microspheres were stable to temperature. The POA/DAA ratio in the copolymer had effect not only on the cloud point but also on the size of the microspheres. The copolymer with a lower DAA content formed smaller microspheres.     

Dry Potassium-Based Sorbents for CO<Subscript>2</Subscript> Capture

Dry potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, CaO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property of various sorbents were measured in the presence of H₂O in a fixed bed reactor, during multiple cycles at various temperature conditions (CO₂ absorption at 50–100 °C and regeneration at 130–400 °C). The KAlI30, KCaI30, and KMgI30 sorbents formed new structures such as KAl(CO₃)₂(OH)₂, K₂Ca(CO₃)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely convert to the original K₂CO₃ phase at temperatures below 200 °C, during the CO₂ absorption process in the presence of 9 vol.% H₂O. In the case of KACI30, KTiI30, and KZrI30, only a KHCO₃ crystal structure was formed during CO₂ absorption. The formation of active species, K₂CO₃·1.5H₂O, by the pretreatment with water vapor and the formation of the KHCO₃ crystal structure after CO₂ absorption are important factors for absorption and regeneration, respectively, even at low temperatures (130–150 °C). In particular, the KTiI30 sorbent showed excellent characteristics with respect to CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (87 mg CO₂/g sorbent) without the pretreatment with water vapor, unlike KACI30, and a fast and complete regeneration at a low temperature condition (1 atm, 150 °C). In addition, the higher total CO₂ capture capacity of KMgI30 (178.6 mg CO₂/g sorbent) than that of the theoretical value (95 mg CO₂/g sorbent) was explained through the contribution of the absorption ability of MgO support. In this review, we introduce the CO₂ capture capacities and regeneration properties of several potassium-based sorbents, the changes in the physical properties of the sorbents before/after CO₂ absorption, and the role of water vapor and its effects on CO₂ absorption.     

Photocatalytic reduction of CO<Subscript>2</Subscript> over TiO<Subscript>2</Subscript> based catalysts

At present, carbon dioxide is considered the largest contributor among greenhouse gases. This review covers the current state of problem of carbon dioxide emissions from industrial and combustion processes, the principle of photocatalysis, existing literature related to photocatalytic CO₂ reduction over TiO₂ based catalysts and the effects of important parameters on the process performance including light wavelength and intensity, type of reductant, metal-modified surface, temperature and pressure. Presented at the 34th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 21–25 May 2007.     

Investigation of miniature CO<Subscript>2</Subscript> gas sensor based on NASICON

A miniature CO₂ gas sensor based on NASICON (sodium super ionic conductor) thick film was fabricated. The solid-electrolyte NASICON material was synthesized through an inorganic-reagent-based sol-gel method. The resulting materials were characterized by means of X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). NASICON paste was coated on a piece of alumina substrate attached to a platinum heater. Li₂CO₃-BaCO₃ binary carbonate in molar ratio 1 : 1.5 was utilized as the sensing electrode. Within a wide range of CO₂ volume ratio concentration from 500 to 5000 ppm, the output electromotive force (EMF) of the sensor followed Nernst equation well at high working temperature. The response and recovery times were 20 and 58 s, respectively. This miniature CO₂ gas sensor possessed extra merits such as low power consumption, miniaturized framework, and easy fabrication.     

Experimental determination and calculation of the critical curves for the binary systems of CO2 containing ketone, alkane, ester and alcohol, respectively

A set of variable-volume autoclave with a quartz window was used for the experimental determination of the high-pressure phase equilibria and critical curves. The critical temperatures, pressures, densities and mole volumes in the region near the critical point of CO₂ were examined for eleven binary systems of supercritical CO₂ (SC CO₂) with different kinds of substances (ketone, alkane, ester and alcohol), respectively. The critical curves of the above binary systems were also calculated using an equation of state. The equation consists of a hard body repulsion term and an additive perturbation term, which takes care of the attractive molecular interaction. The calculated data were compared with the experimental data, and yielded good agreements. At the same time, the values of the adjustable parameters, λ, k_σ and k_? were obtained. The critical curves of the above eleven binary systems at higher temperatures and pressures all belong to type I.     

Low-temperature processing of sol-gel derived Pb(Zr,Ti)O<Subscript>3</Subscript> thick films using CO<Subscript>2</Subscript> laser annealing

Fabrication of ferroelectric Pb(Zr_0.52Ti_0.48)O₃ (PZT) thick films on a Pt/Ti/SiO₂/Si substrate using powder-mixing sol-gel spin coating and continuous wave CO₂ laser annealing technique to treat the specimens with at a relatively low temperature was investigated in the present work. PZT fine powders were prepared by drying and pyrolysis of sol-gel solutions and calcined at temperatures from 400 to 750°C. After fine powder-containing sol-gel solutions were spin-coated on a substrate and pyrolyzed, CO₂ laser annealing was carried out to heat treat the specimens. The results show that laser annealing provides an extremely efficient way to crystallize the materials, but an amorphous phase may also form in the case of overheating. Thicker films absorb laser energy more effectively and therefore melt at shorter periods, implying a significant volume effect. A film with thickness of 1 μm shows cracks and rough surface morphology and it was difficult to obtain acceptable electrical properties, indicating importance of controlling interfacial stress and choosing appropriate size of the mixing powders. On the other hand, a thick film of 5 μm annealed at 100 W/cm² for 15 s exhibits excellent properties (P _r = 36.1 μC/cm², E _c = 19.66 kV/cm). Films of 10 μm form a melting zone at the surface and a non-crystallized bottom layer easily at an energy density of 100 W/cm², showing poor electrical properties. Besides, porosity and electrical properties of thick films can be controlled using appropriate processing parameters, suggesting that CO₂ laser annealing of modified sol-gel films is suitable for fabricating films of low dielectric constants and high crystallinity.     

The reactions and composition of the surface intermediate species in the selective catalytic reduction of NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> with ethylene over Co-ZSM-5

A pretreatment-transient reaction product analysis method was applied to study the reactions and average composition of the possible surface intermediate species in selective catalytic reduction with ethylene of NO _x over Co-ZSM-5. The reactions of the surface species, formed by the pretreatment of Co-ZSM-5 in a NO/C₂H₄/O₂ mixture at 275°C, with the NO/O₂ flow produced much more N₂ than that with the individual NO or O₂ flow. The similarity of N₂/CO _x /H₂O product distribution generated from the above surface species-NO/O₂ reactions and that from the normal NO/C₂H₄/O₂ flow reactions implies that the surface species NC _a O _b H _c formed in the three-component pretreatment process is very likely the primary intermediate surface species generated during the real flow reactions. The in situ FT-IR (DRIFT) spectroscopy measurements of the surface species support the above conclusion.     

Application of thermogravimetric analysis to the evaluation of aminated solid sorbents for CO<Subscript>2</Subscript> capture

In this work a series of solid sorbents were synthesized by immobilizing liquid amines on the surface of a mesoporous alumina. The samples were chemically characterized and BET surface areas calculated from the N₂ adsorption isotherms at 77 K. The CO₂ capture performance of the sorbents and their thermal stability was studied by thermogravimetric methods. The effect of amine loading on the CO₂ capture performance of the prepared sorbents was also evaluated. Analysis of TG-DTG curves showed that thermal stabilization of the amines is significantly improved by immobilizing them on an inorganic support. Temperature-programmed CO₂ adsorption tests from 298 K up to 373 K at atmospheric pressure, proved to be a useful technique for assessing the capacity of sorbents for CO₂ capture. Alumina impregnated with diethylenetriamine presented the highest CO₂ adsorption capacities throughout the tested temperature range.     

Construction and characterization of alkoxy-derived (Y,Yb)MnO<Subscript>3</Subscript>/HfO<Subscript>2</Subscript>/Si structures for FeRAM application

(Y,Yb)MnO₃ and HfO₂ films were prepared using alkoxy-derived precursor solutions, and (Y,Yb)MnO₃/HfO₂/Si structures were fabricated. The thickness, surface uniformity and crystallinity of the HfO₂ film affect the crystallization of Y_0.5Yb_0.5MnO₃ films. The degree of c-axis orientation and crystallinity of the Y_0.5Yb_0.5MnO₃ films were changed with preparation conditions of HfO₂ films. It was difficult to obtain Y_0.5Yb_0.5MnO₃ films with high crystallinity and high degree of c-axis orientation on the HfO₂ films thinner than 10 nm. The degree of c-axis orientation and crystallinity of the Y_0.5Yb_0.5MnO₃ films on HfO₂ films were improved by using diluted HfO₂ precursor solution in the case of 10 nm-thick HfO₂ film. Following this, the capacitance-voltage (C-V) characteristics were improved.     

In situ FT-IR spectroscopic study on the conformational changes of isotactic polypropylene in the presence of supercritical CO2

The conformational changes of isotactic polypropylene (iPP) under supercritical CO₂ condition with different pressure and temperature have been carefully studied by in situ Fourier-transform infrared spectroscopy (FT-IR). Analysis of the corresponding spectra shows that the conformational ordering by supercritical CO₂ results in the intensity enhancement of the regularity bands of iPP. Due to the high CO₂ concentration and strong intermolecular interaction, iPP can reach an equilibrium state in a short time at high CO₂ pressure. The equilibrium time increases with soaking temperature. After supercritical CO₂ treatment, two mechanisms, the formation of short helix from amorphous phase and the extension of short helix into long one, happen simultaneously. The latter mechanism undergoes quickly at the beginning of induced conformational changes and then slows down, resulting in the slight increase of crystallinity. At the same time, the conformational ordering in amorphous phase happens continuously until a thermodynamic equilibrium. In summary, in the presence of supercritical CO₂, the conformational ordering of iPP chains occurs exclusively in the amorphous region, with no impact on the crystal part.     

Fast CO<Subscript>2</Subscript> sequestration by aerogel composites

The increasingly evident impact of anthropogenic CO₂ emissions on climate change and associated environmental effects is stimulating the search for viable methods to remove this gas. One of the most promising strategies is the long-term storage of CO₂ in inert, insoluble and thermodynamically-stable materials. This strategy mimics the natural reactions that transform silicates into carbonates regulating the cycle of CO₂ on the surface of the Earth, operating on a geological time-scale. Consequently, the aim is to accelerate these reactions to be applicable on the timescale of human lives. We present the various technologies developed or proposed to date, based on this particular approach. The principal limiting factor is that high pressures and temperatures are required to produce appropriate materials capable of CO₂ sequestration and storage. Nevertheless, the synthetic materials known as aerogels can be modified in shape, size and chemical functionality so as to catalyse the process of CO₂ elimination through silicates (of Ca or Mg), considerably reducing the reaction time and working at atmospheric pressure and temperature.     

Sodium and silver phosphate glasses doped with chlorides of Fe,Mn and Zn

A number of samples of sodium and silver phosphate glasses doped with various compositions of some transition metals viz. iron, manganese and zinc chlorides alongwith undoped samples of sodium and silver phosphate glasses were synthesized and characterized by X-ray diffraction, IR spectral, electrical conductivity and differential scanning calorimetry (DSC). The glass transition temperature (T _g) and crystallization temperature (T _c) values obtained from DSC curves were found to increase with increasing concentration of the dopant Fe/Mn/Zn chlorides in both sodium and silver phosphate glasses and the following sequence is observed: T _g(–FeCl₃)>T _g(–MnCl₂)>T _g(–ZnCl₂) T _c(–FeCl₃)>T _c(–MnCl₂)>T _c(–ZnCl₂) The increase in T _g and T _c values indicate enhanced chemical durability of the doped glasses. The electrical conductivity values and the results of FTIR spectral studies have been correlated with the structural changes in the glass matrix by the addition of different transition metal cations as dopants.     

Preparation and Characterization of PVDF‐HFP Membrane

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) microporous membrane was prepared by supercritical CO₂ extraction of dibutyl phthalate (DBP) template from PVDF‐HFP/DBP film. The effects of extraction conditions such as pressure, temperature, and extraction time on extraction efficiency and the porosity of membrane were studied. The extraction efficiency of DBP and size stability of polymer membrane during extraction was compared with those of solvent extraction process. The structure of the resulting membrane was characterized by scanning electron microphotograph (SEM), X‐ray diffraction (XRD) and differential scanning calorimeter (DSC). With increasing the extraction temperature, pressure and time, the extraction efficiency and the porosity increased. Maximum extraction efficiency is obtained at extraction pressure and temperature higher than 18 MPa and 75°C, respectively. The porosity of membranes depended on the extraction efficiency and shrinkage ratio of membranes. Compared with solvent extraction, supercritical CO₂ extraction of the film generated the membrane with more uniform structure and higher porosity.