The Crystallization and Melting Behaviors of PDLA-b-PBS-b-PDLA Tri-block Copolymers

In this study,the poly(D-lactide)-block-poly(butylene succinate)-block-poly(D-lactide)(PDLA-b-PBS-b-PDLA)triblock copolymers with a fixed length of PBS and various lengths of PDLA are synthesized,and the crystallization behaviors of the PDLA and PBS blocks are investigated.Although both the crystallization behaviors of PBS and PDLA blocks depend on composition,they exhibit different variations.For the PDLA block,its crystallization behaviors are mainly influenced by temperature and block length.The crystallization signals of PDLA block appear in the B-D 2-2 specimen,and these signals get enhanced with PDLA block length.The crystallization rates tend to decrease with increasing PDLA block lendth during crystallizing at 90 and 100°C.Crystallizing at higher temperature,the crystallization rates increase at first and then decrease with block length.The crystallization rates decrease as elevating the crystallization temperature.The melting temperatures of PDLA blocks increase with block lengths and crystallization temperatures.For the PBS block,its crystallization behaviors are mainly controlled by the nucleation and confinement from PDLA block.The crystallization and melting enthalpies as well as the crystallization and melting temperatures of PBS block reduce as a longer PDLA block has been copolymerized,while the crystallization rates of the PBS block exhibit unique component dependence,and the highest rate is observed in the B-D 2-2 specimen.The Avrami exponent of PBS crystallites is reduced as a longer PDLA block is incorporated or the sample is crystallized at higher temperature.This investigation provides a convenient route to tune the crystallization behavior of PBS and PLA.     

Linear and four‐armed poly(l‐lactide)‐block‐poly(d‐lactide) copolymers and their stereocomplexation with poly(lactide)s

Linear and four‐armed poly(l ‐lactide)‐block‐poly(d ‐lactide) (PLLA‐b‐PDLA) block copolymers are synthesized by ring‐opening polymerization of d ‐lactide on the end hydroxyl of linear and four‐armed PLLA prepolymers. DSC results indicate that the melting temperature and melting enthalpies of poly (lactide) stereocomplex in the copolymers are obviously lower than corresponding linear and four‐armed PLLA/PDLA blends. Compared with the four‐armed PLLA‐b‐PDLA copolymer, the similar linear PLLA‐b‐PDLA shows higher melting temperature (212.3 °C) and larger melting enthalpy (70.6 J g^?1). After these copolymers blend with additional neat PLAs, DSC, and WAXD results show that the stereocomplex formation between free PLA molecular chain and enantiomeric PLA block is the major stereocomplex formation. In the linear copolymer/linear PLA blends, the stereocomplex crystallites (sc) as well as homochiral crystallites (hc) form in the copolymer/PLA cast films. However, in the four‐armed copolymer/linear PLA blends, both sc and hc develop in the four‐armed PLLA‐b‐PDLA/PDLA specimen, which means that the stereocomplexation mainly forms between free PDLA molecule and the inside PLLA block, and the outside PDLA block could form some microcrystallites. Although the melting enthalpies of stereocomplexes in the blends are smaller than that of neat copolymers, only two‐thirds of the molecular chains participate in the stereocomplex formation, and the crystallization efficiency strengthens. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1560–1567     

Novel Thermo‐Responsive Formation of a Hydrogel by Stereo‐Complexation between PLLA‐PEG‐PLLA and PDLA‐PEG‐PDLA Block Copolymers

Gel formation was discovered in an aqueous mixture of enantiomeric triblock copolymers, PLLA‐PEG‐PLLA and PDLA‐PEG‐PDLA. This system is characteristic in that an interesting sol–gel transition was induced by the stereo‐complexation of the PLLA and PDLA segments of the block copolymers around 37°C. The process of gel formation was clearly monitored by the rheological change, and the responsibility of the stereo‐complex formation for the gelation was confirmed by wide‐angle X‐ray scattering. The mechanism of this gel formation is discussed in relation to its potential applications.     

Effect of Star-shaped chain architectures on the polylactide stereocomplex crystallization behaviors

Linear and star-shaped polylactides (PLA) with similar molecular weights of each arm are synthesized via ring-opening polymerization of LA with 3-butyn-l-ol and pentaerythritol as initiators,respectively.By solution blending of equivalent mass of poly(L-lactic acid)s (PLLAs) and poly(D-lactic acid)s (PDLAs),perfect PLA stereocomplexes (scPLAs) are prepared and confirmed by WAXD and FTIR analysis.Effect of chain architectures on stereocomplex crystallization is investigated by studying the non-isothermal and isothermal crystallization of linear and star-shaped polylactide stereocomplexes.In dynamic DSC and POM test,star-shaped PLLA (4sPLLA)/PDLA and PLLA/star-shaped PDLA (4sPDLA) stereocomplexes reach rapid crystallization and higher crystallinity due to larger spherulite density of star-shaped chain and excellent chain mobility of linear chain.In isothermal crystallization test,much faster crystallization and less crystallization half-time is obtained with the increase of star-shaped chain.Meanwhile,4sPLLA/PDLA and PLLA/4sPDLA are found to have the highest crystallinity,suggesting limitation of too much star-shaped chain for 4sPLLA/4sPDLA and restriction of linear chain in nucleation capacity for PLLA/PDLA.The results reveal that star-shaped chain has an important influence on the crystallization of scPLAs.     

Synthesis and properties of high‐molecular‐weight stereo di‐block polylactides with nonequivalent D/L ratios

Di‐stereoblock polylactides (di‐sb‐PLA: PLLA‐b‐PDLA) having high molecular weight (M_n > 100 kDa) were successfully synthesized by two‐step ring‐opening polymerization (ROP) of L ‐ and D ‐lactides using tin(2‐ethylhexanoate) as a catalyst. By optimizing the polymerization conditions, the block sequences were well regulated at non‐equivalent feed ratios of PLLA and PDLA. This synthetic method consisted of three stages: (1) polymerization of either L ‐ or D ‐lactide to obtain a PLLA or PDLA prepolymer with a molecular weight less than 50 kDa, (2) purification of the obtained prepolymer to remove residual lactide, and (3) polymerization of the enantiomeric lactide in the presence of the purified prepolymer. Their ¹³C and ³¹P NMR spectra of the resultant di‐sb‐PLAs strongly supported their di‐stereo block structure. These di‐sb‐PLAs, having weight‐average molecular weights higher than 150 kDa, were fabricated into polymer films by solution casting and showed exclusive stereocomplexation. The thermomechanical analysis of the films revealed that their heat deformation temperature was limited probably because of their low crystallinity owing to the non‐equivalent PLLA/PDLA ratio. The blend systems of the di‐sb‐PLAs having complementary stereo‐sequences (the one with a long PLLA block and the other with long PDLA block) were also prepared and characterized to enhance the sc crystallinity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 794–801, 2010     

Hydrogel formation between enantiomeric B-A-B-type block copolymers of polylactides (PLLA or PDLA: A) and polyoxyethylene (PEG: B); PEG-PLLA-PEG and PEG-PDLA-PEG

A mixed suspension of the enantiomeric B-A-B triblock copolymers, polyoxyethylene-block-poly(L-lactide)-block-polyoxyethylene (PEG-PLLA-PEG) and polyoxyethylene-block-poly(D-lactide)-block-polyoxyethylene (PEG-PDLA-PEG), was found to induce reversible gel-to-sol transition depending on the polymer concentration and temperature. The storage and loss moduli of the gel formed at lower temperature were much higher than those of the gel prepared from the corresponding ABA-type triblock copolymers because of the higher polymer concentration in the former. Although the stereo-complexation of the PLLA and PDLA blocks occurred at higher temperature also in the B-A-B copolymers, it was not responsible for the gelation of the mixed suspension. The PEG chains, involved in the helix formation of the PLLA and PDLA, should form helices with opposite helical senses to aggregate and lead the gelation of the system.     

Enhancing crystallization behavior for optimized performances of poly(TMC‐b‐(LLA‐ran‐GA)) by PDLA/PLLA stereocomplex crystallization

The blends of poly(1,3‐trimethylene carbonate‐b‐(l ‐lactide‐ran‐glycolide)) (PTLG) with poly(d ‐lactide) (PDLA) were prepared via solution‐casting method using CH₂Cl₂ as solvent. The poly(l ‐lactide) (PLLA) segments of PTLG with PDLA chain constructed as stereocomplex structures and growth stereocomplex crystals of PLA (sc‐PLA). The effects of sc‐PLA crystals on thermal behavior, mechanical properties, thermal decomposition of the PTLG/PDLA blends were investigated, respectively. The differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results showed that the total crystallinity of the PTLG/PDLA blends was increased with the PDLA content increasing. Heterogeneous nucleation of sc‐PLA crystals induced crystallization of the PLLA segments in PTLG. The crystallization temperature of samples shifted to 107.5°C for the PTLG/PDLA‐20 blends compared with that of the PTLG matrix, and decreased the half‐time of crystallization. The mechanical measurement results indicated that the tensile strength of the PTLG/PDLA blends was improved from 21.1 MPa of the PTLG matrix to 39.5 MPa of PTLG/PDLA‐20 blends. The results of kinetics of thermal decomposition of the PTLG/PDLA blends by TGA showed that the apparent activation energy of the PTLG/PDLA blends was increased from 59.1 to 72.1 kJ/mol with the increasing of the PDLA content from 3 wt% to 20 wt%, which indicated the enhancement of thermal stability of the PTLG/PDLA blends by addition of PDLA. Furthermore, the biocompatibility of the PTLG/PDLA blends cultured with human adipose‐derived stem cells was evaluated by CCK‐8 and live/dead staining. The experiment results proved the PTLG/PDLA blends were a kind of biomaterial with excellent physical performances with very low cytotoxicity.     

三臂支化PLLA-PDLA嵌段共聚物的合成及立构复合结晶行为

以三羟甲基乙烷为起始剂, 开环聚合L-丙交酯(LLA), 合成三臂支化左旋聚乳酸(PLLA)预聚物. 采用端基活化技术对预聚物进行端羟基活化, 再与D-丙交酯(DLA)进行开环聚合, 合成了不同分子量的三臂支化左旋聚乳酸-右旋聚乳酸(PLLA-PDLA)嵌段共聚物. 采用核磁共振谱和凝胶渗透色谱等对样品的结构和分子量进行测试, 结果表明,合成的嵌段共聚物链结构具有链段立构规整度和高分子量的特点; 通过调节DLA单体与PLLA预聚物的投料比, 可实现对PLLA-PDLA嵌段共聚物的序列结构调控. 差示扫描量热仪和广角X 射线衍射结果表明, 三臂支化PLLA-PDLA嵌段共聚物的异构体分子间生成立构复合晶体, 其熔点高于200℃; 共聚物的嵌段序列结构对材料的凝聚态转变行为有很大的影响.     

Novel poly(l‐lactide)/poly(d‐lactide)/poly(tetrahydrofuran) multiblock copolymers with a controlled architecture: Synthesis and characterization

Novel poly(l ‐lactide) (PLLA)/poly(d ‐lactide) (PDLA)/poly(tetrahydrofuran) (PTHF) multiblock copolymers with designed molecular structure were synthesized by a two‐stage procedure. Well‐defined PDLA‐PLLA‐PTHF‐PLLA‐PDLA pentablock copolymers were prepared by sequential ring opening polymerization of l ‐ and d ‐lactides starting from PTHF glycol, with the length of the (equimolar) PLLA and PDLA blocks being varied. Then, these dihydroxyl‐terminated pentamers were transformed into multiblock copolymers by melt chain‐extension with hexamethylene diisocyanate–being the first time that the coupling of pentablock units is reported. The successful formation of macromolecular chains with a multiblock and well‐defined architecture was demonstrated by ¹H NMR spectroscopy. The thermal properties and structuring of the resulting materials were investigated by means of DSC and WAXD measurements and DMA analysis. Stereocomplexation was found to be promoted during solution and melt crystallization. This approach affords materials combining the high rigidity and strength (other than improved thermal resistance) of the hard stereocomplex crystallites with the flexibility imparted by the soft block, whereby their properties can be finely tailored through the composition of the basic pentablock units without limitations on the final molecular weight. The adopted reaction conditions make this process highly appealing in view of the possibility to perform it in extruder. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3269–3282     

Biodegradable stereocomplex materials of polylactide‐grafted dextran exhibiting soft and tough properties in dry and wet states

Water‐swellable biodegradable materials exhibiting mechanically tenacious and tough characters in the wet state were prepared by a simple blend of two enantiomeric polylactide‐grafted dextran copolymers (Dex‐g‐PLLA and Dex‐g‐PDLA). DSC and WAXD analyses demonstrated the formation of SC crystals in the copolymer blend films. SC blend films showed lamellar‐type microphase‐separated structures. When swollen with water, these blend films showed the same level of tensile strengths and Young's modulus as the films in the dry state. SC blend films degraded gradually over a month under physiological conditions with a degradation rate faster than the corresponding Dex‐g‐PLLA films. The SC‐forming enantiomeric mixture of polylactide‐grafted polysaccharides should be a good candidate for an implantable biocompatible material exhibiting favorable mechanical properties and degradation behavior. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Tailoring the LCST of PNIPAAM‐b‐PLA‐b‐PNIPAAM Triblock Copolymers via Stereocomplexation

Poly(N‐isopropylacrylamide)‐block‐poly(l ‐lactic acid)‐block‐poly(N‐isopropylacrylamide) (PNIPAAM‐b‐PLLA‐b‐PNIPAAM) and PNIPAAM‐b‐PDLA‐b‐PNIPAAM triblock copolymers with varying polylactic acid (PLA) lengths are synthesized using a combination of ring‐opening polymerization and atom‐transfer radical polymerization. Results of ¹H NMR and gel permeation chromatography analyses show that the copolymers have a well‐defined triblock structure and the PLA segment lengths can be readily controlled with monomer feed ratio. Stereocomplexation between the enantiomeric PLA segments is confirmed with differential scanning calorimetry and wide‐angle X‐ray scattering. Dynamic light scattering experiments show that (1) the LCST of PNIPAAM in water could be tailored from 32 °C up to 38.5 °C by increasing the length of PLA segments and mixing copolymers of similar molecular weight with enantiomeric PLA segments to induce stereocomplexation, and (2) the LCST of each mixed copolymer system could be tailored within a 2–3 °C range of body temperature by manipulating the ratio of the enantiomeric copolymers in solution.

     

Rheology and crystallization behavior of asymmetric PLLA/PDLA blends based on linear PLLA and PDLA with different structures

In this study, several asymmetric poly(L‐lactide)/poly(D‐lactide) (PLLA/PDLA) blends were prepared by adding small amounts of PDLA with different structures into linear PLLA matrix. The effect of PDLA on rheological behavior, crystallization behavior, nucleation efficiency and spherulite growth of PLLA was investigated. Rheological results indicated that PLLA/PDLA blends showed solid‐like viscoelastic behavior at low temperature (<200°C), and the cross‐linking density of PLLA/PDLA melt at 180°C followed the order: PLLA/6PDLA > PLLA/L‐PDLA > PLLA/3PDLA > PLLA/4PDLA. No‐isotherm and isotherm crystallization results indicated that the crystallization capacity of PLLA/PDLA blends was strongly related to the PDLA structure, crystallization temperature and thermal treatment temperature. Furthermore, the dimension of crystal growth during isotherm crystallization presented the obvious dependent on the PDLA structure. The nucleation efficiency of sc‐crystallites in the blends and spherulite density during isothermal crystallization were also studied. Nucleation efficiency of sc‐crystallites in the PLLA/S‐PDLA blends showed the obvious dependent on thermal treatment temperature with respect to PLLA/L‐PDLA, and nucleation efficiency sc‐crystallites in the PLLA/S‐PDLA blends first decreased and then increased as the thermal treatment temperature increased. Spherulite density of PLLA/PDLA blends was also related to thermal treatment temperature and the PDLA structure. This study has discussed the temperature dependence of the stereocomplex networks between PLLA and PDLA with different structure, and then its consequential influence on rheology and crystallization capacity of PLLA, which would provide the theoretical direction for PLA processing. Copyright © 2016 John Wiley & Sons, Ltd.     

Different enantioselectivity of two types of poly(lactic acid) depolymerases toward poly(l-lactic acid) and poly(d-lactic acid)

Poly(lactic acid) (PLA) depolymerases are categorized into protease-type and lipase-type. Protease-types can hydrolyze poly(l-lactic acid) (PLLA) but not poly(d-lactic acid) (PDLA). Lipase-types, including cutinase-like enzyme (CLE) from Cryptococcus sp. strain S-2 preferentially hydrolyze PDLA. Both enzymes degraded not only PLA emulsion but also PLA film, in which amorphous region is preferentially attacked, but crystalline region can be also attacked. Stereocomplex PLA (sc-PLA) formed by 50:50 blending of PLLA and PDLA included no homo crystals, but a tiny homo crystallization peak appeared and crystallinity increased by 5% when attacked by CLE, although no significant change of molecular weight and crystalline size was found. Enantioselective degradation must occur in amorphous region of PLLA/PDLA film and preferentially hydrolyzed PDLA, resulting in a slightly excess amount of PLLA remained, which must be crystallized.     

Synthesis and mechanochemical properties of biobased ABCBA-type pentablock copolymers comprising poly-d-lactide (A), poly-l-lactide (B) and poly(1,2-propylene succinate) (C)

The ABCBA pentablock copolymers (p-d -l -PPS) comprising poly(d -lactide) (PDLA: A), poly(l -lactide) (PLLA: B) and poly(propylene succinate) (PPS: C) were successfully synthesized by two-step ring-opening polymerization (ROP) of d - and l -lactide using a dihydroxy-terminated PPS as a macro-initiator. The pentablock copolymers revealed the high stereocomplex (sc) crystallinity, thermal stability and elastomeric property in their solution-cast films. It was found that the T_g was found to be proportional to the PPS content, whereas the T_m was proportional to their average block length. The thermal resistivity of the copolymer films was found to be as high as 202°C owing to their sc formation. The copolymers also showed improved stereocomplexibility compared to the enantiomeric mixtures of triblock copolymers (PLLA-PPS-PLLA and PDLA-PPS-PDLA) having similar PLLA and PDLA chain lengths. These pentablock copolymers can afford thermoplastic elastomers or flexible plastic materials having a 100% bio-based content, showing high heat-resistive property.     

Greatly accelerated crystallization of poly(lactic acid): cooperative effect of stereocomplex crystallites and polyethylene glycol

Stereocomplex crystallite (SC) between enantiomeric poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA), with largely improved thermal resistance and mechanical properties compared with PLLA and PDLA, is a good nucleating agent for poly(lactic acid) (PLA). The effects of SC and/or polyethylene glycol (PEG) on the crystallization behaviors of PLA were investigated. The non-isothermal and isothermal crystallization kinetics revealed that SC and PEG can separately promote the crystallization rate of PLA by heterogeneous nucleation and increasing crystal growth rate, respectively. However, their promoting effect is limited when used alone, and the modified PLA cannot crystallize completely under a cooling rate of 20 °C/min. When SC and PEG are both present, the crystallization rate of PLA is greatly accelerated, and even under a cooling rate of 40 °C/min, PLA can crystallize completely and get a high crystallinity owing to the excellent balance between simultaneously improved nucleation and crystal growth rate.     

Synthesis of biodegradable thermoplastic elastomers from ε‐caprolactone and lactide

This article reports the synthesis and the properties of novel thermoplastic elastomers of A‐B‐A type triblock copolymer structure, where the hard segment A is poly(l ‐lactide) (PLLA) and the soft segment B is poly(ε‐caprolactone‐stat‐d ,l ‐lactide) (P(CL‐stat‐DLLA)). The P(CL‐stat‐DLLA) block with DLLA content of 30 mol % was applied because of its amorphous nature and low glass transition temperature (T_g = approximately ?40 °C). Successive polymerization of l ‐lactide afforded PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLAs, which exhibited melting temperature (T_m = approximately 150 °C) for the crystalline PLLA segments and still low T_g (approximately ?30 °C) of the soft segments. The triblock copolymers showed very high elongation at break up to approximately 2800% and elastic properties. The corresponding d ‐triblock copolymers, PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLAs (PDLA = poly(d ‐lactide)) were also prepared with the same procedure using d ‐lactide in place of l ‐lactide. When the PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLA was blended with PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLA, stereocomplex crystals were formed to enhance their T_m as well as tensile properties. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 489–495     

三臂PPO-PDLA-PLLA 嵌段共聚物的制备与结构及其立构复合体的结晶行为

以环氧丙烷聚醚三元醇(PPO)为起始剂, 开环聚合D 型丙交酯(DLA), 合成三臂环氧丙烷聚醚三元醇-聚右旋乳酸(PPO-PDLA)嵌段预聚体. 采用端基活化技术对预聚体进行端羟基活化, 再与L 型丙交酯(LLA)进行逐步开环聚合,合成了不同分子量的三臂环氧丙烷聚醚三元醇-聚右旋乳酸-聚左旋乳酸(PPO-PDLA-PLLA)嵌段共聚物. 采用红外(FTIR)、核磁(NMR)和凝胶渗透色谱(GPC)等对三臂PPO-PDLA-PLLA 嵌段共聚物的测试表明, 合成的嵌段共聚物分子链具有很高的立构规整度; 通过调节LLA 单体与PPO-PDLA 预聚体的投料比, 不仅可控制产物的分子序列结构, 而且样品的数均分子量可大于100 kDa. 差示扫描量热仪(DSC)和广角X 射线衍射(WAXD)结果显示, 三臂PPO-PDLAPLLA嵌段共聚物的异构体链段分子间生成立构复合晶体, 其熔点约为200 ℃, 且没有PLLA 均聚物链段结晶现象. 实验结果表明, 这是一类具有实际应用价值的新型耐热聚乳酸(PLA)材料.     

Compatibilized poly(ϵ‐caprolactone)/poly(L‐lactide) blends for biomedical uses

A binary poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) (70/30 w/w) blend and a ternary PLLA/PCL/PLLA‐PCL‐PLLA blend of the same composition which contains 4 wt.‐% of a triblock PLLA‐PCL‐PLLA copolyester as compatibilizing agent were prepared by melt mixing at 200°C. Investigation of the thermal and mechanical properties of the blends and scanning electron microscopy of their fracture surfaces showed in the case of the ternary blend a better state of dispersion of PCL in the PLLA matrix and an improved toughness.     

Characteristics of the biodegradability and physical properties of stereocomplexes between poly(L‐lactide) and poly(D‐lactide) copolymers

Random and block copolymerizations of L ‐ or D ‐lactide with ε‐caprolactone (CL) were performed with a novel anionic initiator, (C₅Me₅)₂SmMe(THF), and they resulted in partial epimerization, generating D ,L ‐ or meso‐lactide polymers with enhanced biodegradability. A blend of PLLA‐r‐PCL [82/18; PLLA = poly(L ‐LA) and PCL = poly(ε‐caprolactone)] and PDLA‐r‐PCL [79/21; PDLA = poly(D ‐LA)] prepared by the solution‐casting method generated a stereocomplex, the melting temperature of which was about 40 °C higher than that of the nonblended copolymers. A blend of PLLA‐b‐PCL (85/15) and PDLA‐b‐PCL (82/18) showed a lower elongation at break and a remarkably higher tensile modulus than stereocomplexes of PLLA‐r‐PCL/PDLA‐r‐PCL and PLLA/PDLA. The biodegradability of a blend of PLLA‐r‐PCL (65/35) and PDLA‐r‐PCL (66/34) with proteinase K was higher than that of PLLA‐b‐PCL (47/53) and PDLA‐b‐PCL (45/55), the degradability of which was higher than that of a PLLA/PDLA blend. A blend film of PLLA‐r‐PDLLA (69/31)/PDLA‐r‐PDLLA (68/32) exhibited higher degradability than a film of PLLA/PDLLA [PDLLA = poly(D ,L ‐LA)]. A stereocomplex of PLLA‐r‐PCL‐r‐PDMO [80/18/2; PDMO = poly(L ‐3,D ,L ‐6‐dimethyl‐2,5‐morpholinedion)] with PDLA‐r‐PCL‐r‐PDMO (81/17/2) showed higher degradability than PLLA‐r‐PDMO (98/2)/PDLA‐r‐PDMO (98/2) and PLLA‐r‐PCL (82/18)/PDLA‐r‐PCL (79/21) blends. The tensile modulus of a blend of PLLA‐r‐PCL‐r‐PDMO and PDLA‐r‐PCL‐r‐PDMO was much higher than that of a blend of PLLA‐r‐PDMO and PDLA‐r‐PDMO. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 438–454, 2005     

Superiority of poly(L-lactic acid) microspheres as dermal fillers

The demand for injectable dermal filler has unde rgone significant growth with the rapid development of the beauty industry.Poly(lactic acid)(PLA) as a benefit of excellent biocompatibility and long-term promotion of collagen regeneration has been favored as a commonly used filler.However,the effects of chirality and particle size of PLA on the efficacy of dermal filler have not been studied.In this study,we prepared three kinds of microspheres(MSs) consisting of poly(D-lactic acid)(PDLA MS),poly(L-lactic acid)(PLLA MS),or meso-PLA(PDLLA MS)at 5,10 and 20 μmto reveal the different biological functions as dermal filler.Following intradermal injection into guinea pig,it was found that PLLA MS induced the slightest inflammation,and the level of pro-inflammatory cytokine IL-1β induced by PLLA MS is only 0.3 or 0.7-fold of that induced by PDLA or PDLLA MS,respectively.More importantly,PLLA MS significantly stimulated the regeneration of collagen,which was 1.4 or 1.1 times higher than those stimulated by PDLA MS or PDLLA MS,respectively.The size of PLA MSs did not affect the levels of inflammation and collagen regeneration.The results confirmed the superiority of PLLA as a dermal filler.