Transport properties of crosslinked acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The diffusion and transport of organic solvents through crosslinked nitrile rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends have been studied. The diffusion of cyclohexanone through these blends was studied with special reference to blend composition, crosslinking systems, fillers, filler loading, and temperature. At room temperature the mechanism of diffusion was found to be Fickian for cyclohexanone–NBR/EVA blend systems. However, a deviation from the Fickian mode of diffusion is observed at higher temperature. The transport coefficients, namely, intrinsic diffusion coefficient (D*), sorption coefficient (S), and permeation coefficient (P) increase with the increase in NBR content. The sorption data have been used to estimate the activation energies for permeation and diffusion. The van't Hoff relationship was used to determine the thermodynamic parameters. The affine and phantom models for chemical crosslinks were used to predict the nature of crosslinks. The experimental results were compared with the theoretical predictions. The influence of penetrants transport was studied using dichloromethane, chloroform, and carbon tetrachloride. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1815–1831, 1999     

Study on the toughening mechanism of PP/EVA dynamically crosslinked blend

The toughening mechanism of polypropylene (PP)/ethylene-co-vinyl acetate (EVA) dynamically crosslinked blend was investigated. The results indicated that dynamical crosslinking technology not only improved the interfacial adhesion between PP and EVA, but also increased the mechanical properties of PP/EVA blend. The quantitative and qualitative analysis of scanning electron microscopy (SEM) micrographs demonstrated that dynamical crosslinking technology could refine EVA particles in PP/EVA blend and promote the size distribution of EVA particles. The critical matrix ligament thickness of dynamically crosslinked and uncrosslinked blend was about 0.55 μm and 0.6 μm, respectively, indicating that the brittle-ductile transition occurred. Dynamic mechanical analysis (DMA) results illustrated that the tan δ peak of PP component in the dynamically crosslinked blend moved toward lower temperature compared with that of pure PP and the PP component in uncrosslinked blend; and the tan δ value of the dynamically crosslinked blend was higher than that of the uncrosslinked blend, which interpreted the toughening mechanism of dynamical crosslinking technology from the dynamic mechanical property of the blend.     

Morphology and mechanical and viscoelastic properties of natural rubber and styrene butadiene rubber latex blends

The morphology and mechanical and viscoelastic properties of a series of blends of natural rubber (NR) and styrene butadiene rubber (SBR) latex blends were studied in the uncrosslinked and crosslinked state. The morphology of the NR/SBR blends was analyzed using a scanning electron microscope. The morphology of the blends indicated a two phase structure in which SBR is dispersed as domains in the continuous NR matrix when its content is less than 50%. A cocontinuous morphology was obtained at a 50/50 NR/SBR ratio and phase inversion was seen beyond 50% SBR when NR formed the dispersed phase. The mechanical properties of the blends were studied with special reference to the effect of the blend ratio, surface active agents, vulcanizing system, and time for prevulcanization. As the NR content and time of prevulcanization increased, the mechanical properties such as the tensile strength, modulus, elongation at break, and hardness increased. This was due to the increased degree of crosslinking that leads to the strengthening of the 3‐dimensional network. In most cases the tear strength values increased as the prevulcanization time increased. The mechanical data were compared with theoretical predictions. The effects of the blend ratio and prevulcanization on the dynamic mechanical properties of the blends were investigated at different temperatures and frequencies. All the blends showed two distinct glass‐transition temperatures, indicating that the system is immiscible. It was also found that the glass‐transition temperatures of vulcanized blends are higher than those of unvulcanized blends. The time–temperature superposition and Cole–Cole analysis were made to understand the phase behavior of the blends. The tensile and tear fracture surfaces were examined by a scanning electron microscope to gain an insight into the failure mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2189–2211, 2000     

Thermogravimetric Analysis and Thermal Ageing of Crosslinked Nitrile Rubber/Poly(ethylene-co-vinyl Acetate) Blends

The thermal behaviour of nitrile rubber (NBR)/poly(ethylene-co-vinyl acetate) (EVA) blends was studied by thermogravimetry. The effects of blend ratio, different crosslinking systems (sulphur, peroxide and mixed), various fillers (silica, clay and carbon black) and filler loading on the thermal properties were evaluated. It was found that the initial decomposition temperature increased with the addition of NBR to EVA. Among the various crosslinking systems studied, the peroxide cured system showed the highest initial decomposition temperature. This is associated with the high bond dissociation energy of C–C linkages. The addition of fillers improved the thermal stability of the blend. The mass loss at different temperatures and activation energy of degradation were also studied. The thermal ageing of these blends was carried out at 50 and 100°C for 72 h. It was seen that the properties are not affected by the mild ageing condition. Also, the peroxide cured system was found to exhibit better retention in properties, than other crosslinking systems. This revised version was published online in August 2006 with corrections to the Cover Date.     

Two‐way multi‐shape memory properties of peroxide crosslinked ethylene vinyl‐acetate copolymer (EVA)/polycaprolactone (PCL) blends

Rare studies have investigated on the 2‐way shape memory crosslinked blends with multiple shape memory behavior up to date. To consider the merit of commercial cost‐competitive crystalline polymers, ethylene vinyl‐acetate copolymer (EVA) / polycaprolactone (PCL) blends (60/40 and 30/70) were peroxide‐cured to form the 2‐way multi‐shape memory crosslinked blends using a melt‐blending method. Both resins were selected to have a similar controlled crosslinking degree, which allowed us to distinctly evaluate their actuation contributions from the cooling‐induced elongation (crystallization) and from the entropy‐driven elongation during cooling process, respectively. In the 2‐way process for the 60/40 system, 2 respective peaks contributed from the cooling‐induced crystallization of EVA and PCL in the cooling curves based on the strain derivate rates at various temperatures were observed. After the cooling process under the loading stress of 150 kPa, the 2‐step heating‐induced contraction process with increasing temperature started at 54.1°C above the melting temperature of PCL at 52.3°C and EVA at 78.3°C, demonstrating 2‐way multi‐shape memory behavior. The multi‐step behavior was more prominent at higher PCL composition and higher load for the 30/70 system. It was found that the entropy‐driven contribution to the overall actuation magnitude increased with increasing nominal loads due to the increased orientation of molecular networks in the blends. The current approach offers numerous possibilities in preparing 2‐way multi‐shape memory crosslinked blends.     

Nonisothermal crystallisation, melting behavior and wide angle X-ray scattering investigations on linear low density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends: effects of compatibilisation and dynamic crosslinking

Crystallisation studies on LLDPE/EVA blends and the individual components were performed with wide angle X-ray scattering (WAXS) technique and differential scanning calorimetry (DSC) DSC was used to characterise the quiescent crystallisation behavior. The heat of fusion and crystallinity of the blends were reduced by the addition of EVA. The experimental and theoretical values of crystallinity of the blends were found to be mutually agreeing. Crystallisation of LLDPE remains impeded to some extent due to the presence of amorphous EVA. Compatibilisation does not affect crystallinity whereas crosslinking decreases crystallinity. Crosslinking and compatibilisation make no significant change in the melting temperature of the blends. X-ray diffraction studies were carried out on un-crosslinked and crosslinked LLDPE/EVA blends with a view to study the effect of blend composition and crosslinking on crystallinity and lattice distance. Studies revealed that LLDPE and EVA have orthorhombic unit cell. Blending with EVA did not affect the crystalline structure of LLDPE, but the crystallinity decreases with EVA content. At low concentrations of EVA the lattice parameters remain unchanged. Above 30% EVA content however, a linear increase has been observed. Dicumyl peroxide (DCP) crosslinked samples show considerable shift of (1 1 0), (2 0 0) and (0 2 0) crystalline peaks towards lower 2θ values indicating an increase of unit cell parameters of the orthorhombic unit cell of polyethylene. At lower EVA-concentrations (<50%) the crystalline structure remains unchanged. For EVA-contents of more than 70% however, increasing DCP-content reduces the crystallinity of the blends and increases the lattice distance. This indicates that DCP-crosslinking is more effective in EVA phase than in the LLDPE phase.     

Effect of EVM/EVA‐g‐MAH ratio on the structure and properties of nylon 1010 blends

The nylon 1010/ethylene‐vinyl acetate rubber (EVM)/maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) ternary blends were prepared. The effect of EVM/EVA‐g‐MAH ratio on the toughness of blends was examined. A super tough nylon 1010 blends were obtained by the incorporation of both EVM and EVA‐g‐MAH. Impact essential work of fracture (EWF) model was used to characterize the fracture behavior of the blends. The nylon/EVM/EVA‐g‐MAH (80/15/5) blend had the highest total fracture energy at a given ligament length (5 mm) and the highest dissipative energy density among all the studied blends. Scanning electron microscopy images showed the EVM and EVA‐g‐MAH existed as spherical particles in nylon 1010 matrix and their size decreased gradually with increasing EVA‐g‐MAH content. Large plastic deformation was observed on the impact fracture surface of the nylon/EVM/EVA‐g‐MAH (80/15/5) blend and related to its high impact strength. Then with increasing EVA‐g‐MAH proportion, the matrix shear yielding of nylon/EVM/EVA‐g‐MAH blends became less obvious. EVM and EVA‐g‐MAH greatly increased the apparent viscosity of nylon 1010, especially at low shear rates. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 877–887, 2009     

Radiation crosslinked Polyolefinic blends: exploring thermally tuned dual Shape Memory character

Shape memory behavior of thermally triggered polymeric materials based on ethylene octene copolymer (EOC) and ethylene propylene diene rubber (EPDM) has been studied in details. Investigation of the shape memory behavior of uncrosslinked EOC–EPDM and electron beam crosslinked EOC–EPDM blends have been pursued thoroughly. Shape memory study has been carried out at 60°C, which shows that with the effect of electron beam radiation shape fixity behavior of the crosslinked blends becomes poor as compared with its uncrosslinked blend system whereas the improvement in shape recovery behavior takes place after the exposure to electron beam radiation. Morphology study by Atomic Force Microscopy (AFM) and crystallinity study by X‐ray diffraction analysis also give the clear idea regarding the formation of crosslinked network structure. Improvement in gel content with increasing radiation dose supports the formation of network structure. Even after the crosslinking in presence of electron beam radiation also, it has been found that crosslinked EPDM rich blends is superior in terms of shape memory behavior point of view. Lower decay of stress value coupled with lower relaxation ratio of crosslinked EPDM rich blend support its superior shape memory behavior. Copyright © 2016 John Wiley & Sons, Ltd.     

Studies on fracture behaviors of immiscible polypropylene/ethylene‐co‐vinyl acetate blends with multiwalled carbon nanotubes

Immiscible polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) blends with two different compositions, one (PP/EVA = 80/20) exhibits the typical sea‐island morphology and the other (PP/EVA = 60/40) exhibits the cocontinuous morphology, were prepared with different contents of f‐MWCNTs. The fracture behaviors, including notched Izod impact fracture and single‐edge notched tensile (SENT) fracture, were comparatively studied to establish the role of f‐MWCNTs in influencing the fracture toughness of PP/EVA blends. Our results showed that, for PP/EVA (80/20) system, f‐MWCNTs do not induce the fracture behavior change apparently. However, for PP/EVA (60/40) system, the fracture toughness of the blend increases dramatically with the increasing of f‐MWCNTs content. More severe plastic deformation accompanied by the fibrillar structure formation was observed during the SENT test. Furthermore, SENT test shows that the significant improvement in fracture toughness of PP/EVA (60/40) with f‐MWCNTs is contributed to the simultaneous enhancement of crack initiation energy and crack propagation energy, but largely dominated by crack propagation stage. Further results based on crystalline structures and morphologies of the blends showed that a so‐called dual‐network structure of EVA and f‐MWCNTs forms in cocontinuous PP/EVA blends, which is thought to be the main reason for the largely improved fracture toughness of the sample. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1331–1344, 2009     

Evaluation of the properties of some nitrile–butadiene rubber/polychloroprene mixes and vulcanizates

Nitrile–butadiene rubber (NBR) has been blended with polychloroprene (CR) in a weight ratio of 1:1. The vulcanizing systems in the blend formulations were varied to obtain non crosslinked CR embedded in vulcanized NBR and non crosslinked NBR embedded in vulcanized CR. The effects of these two different phases on the rheological and mechanical characteristics were evaluated. In addition, the dynamic compliance of the blends was measured over wide ranges of frequency and temperature. It has been found that the mechanical and rheological properties of the vulcanized blends depend on the type of vulcanizing system, its concentration and the presence of reinforcing filler. The mechanical properties of the blend containing N‐cyclohexyl‐2‐benzthiazyl sulphenamide/S as vulcanizing system suitable for NBR are higher than those of the blend containing non‐sulfur vulcanizing system (Zno/Mgo and ethylene thiourea) suitable for CR. Both types of rubber (CR and NBR) in the blend are incompatible as two glass transition temperatures have been observed. Copyright © 2000 John Wiley & Sons, Ltd.     

Melt rheology and morphology of thermoplastic elastomers from polyethylene/nitrile‐rubber blends: The effect of blend ratio,reactive compatibilization,and dynamic vulcanization

A study of the melt‐rheological behavior of thermoplastic elastomers from high‐density polyethylene and acrylonitrile butadiene rubber (NBR) blends was carried out in a capillary rheometer. The effect of the blend ratio and shear rate on the melt viscosity reveals that the viscosity decreases with the shear rate but increases with NBR content. Compatibilization by maleic anhydride modified polyethylene has no significant effect on the blend viscosity, but a finer dispersion of the rubber is obtained, as is evident from scanning electron micrographs. The melt‐elasticity parameters, such as the die swell, principal normal stress difference, recoverable shear strain, and elastic shear modulus of the blends, were also evaluated. The effect of annealing on the morphology of the extrudate reveals that annealing in the extruder barrel results in the coalescence of rubber particles in the case of the incompatible blends, whereas the tendency toward agglomeration is somewhat suppressed in the compatibilized blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1104–1122, 2000     

Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

Thermal, ozone and gamma ageing of styrene butadiene rubber and poly(ethylene-co-vinyl acetate) blends

Ageing behaviour of SBR/EVA blends due to the effects of heat, ozone, and gamma radiation was studied with reference to blend ratio, three crosslinking systems (sulfur, peroxide and mixed) and a compatibiliser (SEBS-g-MA). It was found that an increase in the EVA content of the blends enhanced the ageing characteristics. Among the different crosslinking systems, a peroxide cured system exhibited the best retention of properties even after severe ageing. Tensile strength of peroxide cured SBR/EVA blends increased slightly after ageing for three days at 70 °C due to continued crosslinking, whereas tensile strength of all blends decreased on ageing at 100 °C. Compatibilisation with SEBS-g-MA improved the thermal, gamma and water ageing resistance of SBR/EVA blends.     

ESR study on chemical crosslinking reaction mechanisms of polyethylene using a chemical agent. IV. Effect of sulfur‐ and phosphorous‐type antioxidants

The effect of an antioxidant on the reaction mechanisms of chemical crosslinking of polyethylene (PE) with dicumyl peroxide (DCP) at high temperatures was investigated using electron spin resonance (ESR). For sulfur‐ and phosphorous‐type antioxidants, changes of radical species and their contents during the PE crosslinking reaction were observed. It was confirmed that these antioxidants reacted preferentially with radicals yielded by decomposed DCP, restraining the crosslinking of PE by the increased antioxidant content. The compound of DCP and antioxidant decomposed to form 2‐phenyl isopropyl radicals. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3092–3099, 2000     

Effect of organoclay loading and electron beam irradiation on the physico‐mechanical properties of low‐density polyethylene/ethylene‐vinyl acetate blend

The influence of electron beam (EB) irradiation and organoclay (OC) loading on the properties of low‐density polyethylene (LDPE)/ethylene‐vinyl acetate (EVA) blends was investigated. The samples were subjected to the EB irradiation with the dose values of 50 and 250 kGy. X‐ray diffraction (XRD), gel content, mechanical, thermal, and electrical properties were utilized to analyze the characteristics of the LDPE/EVA blends with and without OC at different irradiation dosages. Gel content analysis showed that the OC promotes considerably the insoluble part so that the LDPE/EVA blends filled with OC become fully crosslinked at 250 kGy; possibly through the formation of further crosslinks between OC and polymer chains. The samples irradiated by EB showed enhanced mechanical properties due to the formation of three‐dimensional networks. In addition, thermogravimetric analysis indicated that combined OC loading and radiation‐induced crosslinking improved thermal stability of LDPE/EVA blends considerably. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of Na‐ionomer on dynamic rheological,dynamic mechanical and creep properties of acrylonitrile styrene acrylate (ASA)/Na+1 poly (ethylene‐co‐methacrylic acid) ionomer blend

A special class of engineered copolymers, called ionomers, comprising both electrically neutral repeating units and a fraction of ionized units was melt blended to weather resistant acrylonitrile/styrene/acrylate (ASA) terpolymer for improved electrical conductivity, heat sealing ability, direct adhesion to several polymers, glass and metals without affecting the aesthetics and colorability of ASA. The similar chemical nature of one of the components of each blended materials viz. acrylate rubber in ASA and acrylic acid of Na‐ionomer in addition to the presence of ionic crosslinking within Na‐ionomer, polar acrylonitrile group in ASA affects chain dynamics as compared to neat polymers. In this context, dynamic rheological properties, DMA properties, creep behavior and DSC of the newly developed ASA/Na‐ionomer blends were analyzed. Based on Na‐ionomer content, the blend system either forms “mushroom” or “brush” type conformation and formation of ionic crosslinking in “brush regime” leads to three tiers Caylay tree conformation. The different chain topology resulted into characteristic loss modulous (G″) curve during stress relaxation process. The chain conformation as well as ionic crosslinking and ion–dipole interaction between the blend components also affected DSC endotherm peak and glass transition temperature. The tan δ peak temperature from DMA also revealed the similar observation. The creep compliance of the blends was dependent on Na‐ionomer content and with temperature. The Findley model analysis of creep compliance suggested that the creep compliance was depended on Na‐ionomer content and ionic crosslinking controlled the creep. The findings can be utilized to design weather resistant smart polymer using suitable filler system. Copyright © 2014 John Wiley & Sons, Ltd.     

Studies on poly(ε‐caprolactone)/thiodiphenol blends: The specific interaction and the thermal and dynamic mechanical properties

The effects of several low molecular weight compounds with hydroxyl groups on the physical properties of poly(ε‐caprolactone) (PCL) were investigated by Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state ¹³C NMR. PCL and 4,4′‐thiodiphenol (TDP) interact through strong intermolecular hydrogen bonds and form hydrogen‐bonded networks in the blends at an appropriate TDP content. The thermal and dynamic mechanical properties of PCL/TDP blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis, respectively. The melting point of PCL decreased, whereas both the glass‐transition temperature and the loss tangent tan δ of the blend increased with an increase in TDP content. The addition of 40 wt % TDP changed PCL from a semicrystalline polymer in the pure state to a fully amorphous elastomer. The molecules of TDP lost their crystallizability in the blends with TDP contents not greater than 40 wt %. In addition to TDP, three other PCL blend systems with low molecular weight additives containing two hydroxyl groups, 1,4‐dihydroxybenzene, 1,4‐di‐(2‐hydroxyethoxy) benzene, and 1,6‐hexanediol, were also investigated with FTIR and DSC, and the effects of the chemical structure of the additives on the morphology and thermal properties are discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1848–1859, 2000     

Sorption and diffusion of normal alkanes through poly(ethylene‐co‐vinyl acetate) membranes

The transport behavior of uncrosslinked and crosslinked poly(ethylene‐co‐vinyl acetate) membranes has been investigated using normal alkanes as probe molecules, in the temperature range of 30–60 °C. Benzoyl peroxide was used for crosslinking the matrix. It has been observed that, a critical concentration of crosslinker is necessary for maximum solvent uptake, followed by a decrease at higher concentration. The effect of free volume on liquid transport was investigated by positron annihilation lifetime spectroscopy. The mechanism of transport has been found to deviate from the regular Fickian behavior. The dependence of the transport coefficients on crosslink density, nature of penetrants, and temperature was studied. The polymer–solvent interaction parameter, enthalpy, and entropy of sorption have also been estimated from the transport data. The affine and phantom models for chemical crosslinks were used to predict the nature of crosslinks. Finally, the experimental sorption data were compared with theoretical predictions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2470–2480, 2007     

Photocrosslinking and related properties of intumescent flame‐retardant LLDPE/EVA/IFR blends

The photoinitiated crosslinking of halogen‐free flame retarded linear low density polyethylene/poly(ethylene‐co‐vinyl acetate) blends (LLDPE/EVA) with the intumescent flame retardant (IFR) of phosphorous‐nitrogen compound (NP) in the presence of photoinitiator and crosslinker and their characterization of related properties have been investigated by gel determination, heat extension test, cone calorimeter test (CCT), thermogravimetric analysis (TGA), Fourier transfer infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), mechanical properties measurements, limiting oxygen index (LOI), UL‐94, and water resistance test. The data from the gel content and heat extension rate (HER) show that the LLDPE/EVA/IFR blends filled with NP are readily crosslinked to a gel content of above 75% and the HER values reach about 50% by UV‐irradiation of 5 sec under suitable amount of photoinitiator and crosslinker. The data obtained from the CCT and LOI indicate that photocrosslinking can considerably decrease the heat release rates (HRR) by 10–15%, prolongate the combustion time, and increase two LOI values for the LLDPE/EVA/NP blends UV irradiated for 5 sec. The results from TGA and the dynamic FTIR spectra give the evidence that the photocrosslinked LLDPE/EVA/NP samples show slower thermal degradation rate and higher thermo‐oxidative degradation temperature than the uncrosslinked LLDPE/EVA/NP samples. The morphological structures of charred residues observed by SEM give the positive evidence that the compact charred layers formed from the photocrosslinked LLDPE/EVA/NP samples play an important role in the enhancement of flame retardant and thermal properties. The data from the mechanical tests and water‐resistant measurements show that photocrosslinking can considerably improve the mechanical and water‐resistant properties of LLDPE/EVA/NP samples. Copyright © 2011 John Wiley & Sons, Ltd.     

Local deformation in photo‐crosslinked polymer blends monitored by Mach‐Zehnder interferometry

Local deformation of a polymer mixture crosslinked by irradiation with ultraviolet light was in situ monitored by using a Mach‐Zehnder interferometer. In combination with the refractive index data obtained from independent measurements, the deformation in the nanometer scales of the crosslinked blends was calculated by using the difference in optical path length of the blend measured before and after irradiation. Upon varying the crosslink density of the blend by changing the light intensity, it was found that the local deformation well correlates with the crosslink density obtained from the reaction kinetics experiments. Furthermore, the strain relaxation of the blends was also monitored in situ and analyzed after irradiation over different time intervals. The results obtained in this study reveal the possibility of monitoring the nanometer‐scale deformation in polymers during radiation curing. These data also provide important information on the correlations between the irradiation‐induced elastic strain and the resulting morphology of reacting polymer blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2898–2913, 2005