Preliminary results on the determination of ultratrace amounts of cadmium in tea samples using a flow injection on-line solid phase extraction separation and preconcentration technique to couple with a sequential injection hydride generation atomic fluorescence spectrometry

In this work, a method was developed for determination of ultra-trace levels of Cd in tea samples by atomic fluorescence spectrometry (AFS). A flow injection solid phase extraction (FI-SPE) separation and preconcentration technique, to on-line couple with a sequential injection hydride generation (SI-HG) technique is employed in this study. Cd was preconcentrated on the SPE column, which was made from a neutral extractant named Cyanex 923, while other matrix ions or interfering ions were completely or mostly separated off. Conditions for the SPE separation and preconcentration, as well as conditions for the HG technique, were studied. Due to the separation of interfering elements, Cd hydride generation efficiency could be greatly enhanced with the sole presence of Co²⁺ with a concentration of 200 μg L⁻¹, which is much lower than those in other works previously reported. Interferences on both the Cd separation and preconcentration, and Cd hydride generation (HG) were investigated; it showed that both the separation and preconcentration system, and the HG system had a strong anti-interference ability. The SPE column could be repeatedly used at least 400 times, a R.S.D. of 0.97% was obtained for 6 measurements of Cd with 0.2 μg L⁻¹ and a correlation coefficiency of 1.0000 was obtained for the measurement of a series of solutions with Cd concentrations from 0.1 to 2 μg L⁻¹. The method has a low detection limit of 10.8 ng L⁻¹ for a 25 mL solution and was successfully validated by using two tea standard reference materials (GBW08513 and GBW07605).     

Modular L-design of hydride atomizers for atomic absorption spectrometry

A novel modular L-shaped design of hydride atomizer for atomic absorption spectrometry is described. It makes it possible to replace the optical tube of the atomizer and, mainly, to employ optical tubes made also from other materials than fused quartz. The design is useful mainly for further improvement of hydride atomizers based on the multiatomizer concept. Employing selenium hydride as the analyte and arsine as the interferent, a preliminary evaluation of performance of three types of L-shaped multiatomizers based on various optical tubes in terms of sensitivity, linearity of calibration graph and resistance to atomization interferences is made. The “classical” T-shaped multiatomizer was employed as a reference.The L-shaped multiatomizer with the optical tube analogous to that employed in the “classical” T-shaped multiatomizer offers virtually the same performance as the reference multiatomizer. Optical tube made of fused quartz with holes with smaller diameters does not offer significantly better performance compared to the reference T-shaped multiatomizer. However, the L-shaped multiatomizer with optical tube fabricated from porous quartz glass overpowers all the other multiatomizers substantially in terms of the resistance against interferences: even the maximum As interferent concentration of 5 µg ml^− 1 does not significantly influence the observed signal. This should be compared with multiatomizers based on plain fused quartz tubes with holes: tolerance limit around 0.5 µg ml^− 1; interferent concentration of 1 µg ml^− 1 causing 20% signal depression.     

Determination of lead in dialysis concentrates using flow injection hydride generation atomic absorption spectrometry

Flow injection hydride generation atomic absorption spectrometry (FI-HGAAS) was used for determination of lead in dialysis concentrates. The parameters such as acidity, concentration of oxidising and reducing agents and argon gas flow rate were investigated to reach the best peak height sensitivity. No significant background signal was observed at high salt concentrations. The detection limit, concentration giving a signal equal to three times standard deviation of the blank signal, was 0.7 ng ml⁻¹ for a 500 μl injection volume. Precision of the measurements at the 20 ng ml⁻¹ level was 3.7% R.S.D. The dialysis concentrates analysed by FI-HGAAS were found to have 10-70 ng ml⁻¹ of lead. The same samples were analysed by ETAAS after removing the matrix using solid phase extraction with Chelex 100. The results were in agreement with those obtained by FI-HGAAS.     

Multicommutation as an environmentally friendly analytical tool in the hydride generation atomic fluorescence determination of tellurium in milk

The aim of this study is to show the advantages of the emerging multicommutation methodology based on the use of solenoid valves for Te determination in milk by hydride generation atomic fluorescence spectrometry (HG-AFS). The delivery of a series of alternating sequential insertions of small volumes of samples and reagents gives rise to new hydrodynamic processes and exciting analytical potentials by controlling the time of flow through the on/off-switched solenoid valves. This drastically reduces the reagent consumption by a factor of 4 and the generation of effluents (590 mL h^–1 instead of 750 mL h^–1 generated by the continuous-mode measurement) and also provides an improvement in the laboratory productivity by an increase of the sample throughput (85 h^–1 compared to 20 h^–1 found in the continuous mode). So, multicommutation is an environmentally and economically sustainable alternative to the methodology based on continuous measurements. The multicommutation-based method developed was applied to tellurium determination in commercially available milk samples; a calibration range of 0.0–0.5 ng mL^–1 and a detection limit of 0.20 ng L^–1 with average relative standard deviation of 2.1% were found. Comparable results were obtained for a series of samples using both continuous and multicommutation HG-AFS modes.     

Determination of arsenic and antimony in milk by hydride generation atomic fluorescence spectrometry

A highly sensitive procedure has been developed for total arsenic and antimony determination in milk samples by hydride generation atomic fluorescence spectrometry after microwave-assisted sample digestion. The discrete introduction of 2 ml of digested sample in the automated continuous flow hydride generation system allows us to reduce drastically the sample and HCl consume and to determine several elements from a same sample digestion. The method provides detection limits of 0.006 and 0.003 ng ml⁻¹, a sensitivity of 2390 and 2840 fluorescence units per ng ml⁻¹ for As and Sb respectively, and average relative standard deviation of 2.3% for As and 4.8% for Sb. The analysis of cow milk samples, obtained from the Spanish market evidenced the presence of As at concentration levels from 3.4 to 11.6 ng g⁻¹ and Sb levels from 3.5 to 11.9 ng g⁻¹, thus in a proportion near to 1:1, which is in contrast with the 10:1 natural ratio between As and Sb and could evidence the effect of the introduction of new alloys and polymer materials in the industrial process of milk. The method was validated by the comparison of data found for commercial samples by using the proposed procedure and reference methods based on dry-ashing and AFS, and microwave-assisted digestion and inductively coupled plasma mass spectrometry determination.     

Separation and sensitive determination of arsenic species (As/As) using the yeast-immobilized column and hydride generation in ICP–AES

Inorganic arsenic was separated using the yeast-immobilized column. Saccharomyces cerevisiae was covalently bonded unto the controlled pore glass, which showed selective preconcentration of As⁵⁺ over As³⁺. The effluent was directly connected to hydride generation (HG) to increase sensitivity. The optimum pH condition for the retainment of arsenic at the column was 7. As⁵⁺ and As³⁺ were completely separated in a few minutes with the flow rate of 1.5 ml min⁻¹. Three molars of nitric acid was adequate both for the elution of As⁵⁺ and hydride generation. The accuracy of the technique was tested with NIST SRMs. Quantitative analysis of arsenic species for herbicide, pesticide, and cigarette were performed, and the results showed good agreements with the suggested values. Yeast-immobilized column-HG-ICP showed a promising future for the arsenic speciation study.     

Occurrence of ochratoxin A in Turkish wines

A total of 95 wine samples including 34 white, 10 rosé and 51 red wines originating from four different Turkish areas were analysed for ochratoxin A (OTA). An analytical method based on immunoaffinity column (IAC) for clean-up and high performance liquid chromatography with fluorescence detection (HPLC-FD) was used to determine OTA in wines. The limit of detection (LOD) was estimated as 0.006 ng ml^− 1 for white wine and 0.010 ng ml^− 1 for rosé and red wines. The limit of quantification (LOQ) was estimated as 0.020 ng ml^− 1 in white wine and 0.030 ng ml^− 1 in rosé and red wines. Recovery experiments were carried out with spiked samples in the range 0.1–1 ng ml^− 1 of OTA. The average OTA recoveries from spiked white wine samples varied from 79.43% to 85.07%; while the mean recoveries for rosé and red wine samples were in the range of 77.48–83.96% and 76.61–83.55%, respectively. OTA was detected in 82 (86%) wine samples at levels of < 0.006–0.815 ng ml^− 1, which were below the maximum allowable limit established by the European Community. The mean OTA concentration in red wines was slightly higher than in white and rosé wines. Furthermore, our data indicate that the geographic region of origin has strong influence on OTA level for white, rosé and red wines: wines originating from Thrace (n = 44, mean = 0.158 ng ml^− 1) and Aegean (n = 28, mean = 0.060 ng ml^− 1) regions of Turkey were more contaminated with OTA compared with wines originating from central (n = 15, mean = 0.027 ng ml⁻¹) and east Anatolia (n = 8, mean = 0.027 ng ml^− 1) areas. This study showed that the occurrence of OTA in Turkish wines is high, but at levels that probably leads to a non-significant human exposure to OTA by consumption of wines.     

Development of a non-chromatographic method for the speciation analysis of inorganic antimony in mushroom samples by hydride generation atomic fluorescence spectrometry

A simple and sensitive method has been developed for the direct determination of toxic species of antimony in mushroom samples by hydride generation atomic fluorescence spectrometry (HG AFS). The determination of Sb(III) and Sb(V) was based on the efficiency of hydride generation employing NaBH₄, with and without a previous KI reduction, using proportional equations corresponding to the two different measurement conditions. The extraction efficiency of total antimony and the stability of Sb(III) and Sb(V) in different extraction media (nitric, sulfuric, hydrochloric, acetic acid, methanol and ethanol) were evaluated. Results demonstrated that, based on the extraction yield and the stability of extracts, 0.5 mol L^− 1 H₂SO₄ proved to be the best extracting solution for the speciation analysis of antimony in mushroom samples. The limits of detection of the developed methodology were 0.6 and 1.1 ng g^− 1 for Sb(III) and Sb(V), respectively. The relative standard derivation was 3.8% (14.7 ng g^− 1) for Sb(V) and 5.1% (4.6 ng g^− 1) for Sb(III). The recovery values obtained for Sb(III) and Sb(V) varied from 94 to 106% and from 98 to 105%, respectively. The method has been applied to determine Sb(III), Sb(V) and total Sb in five different mushroom samples; the Sb(III) content varied from 4.6 to 11.4 ng g^− 1 and Sb(V) from 14.7 to 21.2 ng g^− 1. The accuracy of the method was confirmed by the analysis of a certified reference material of tomato leaves.     

Flow injection-hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth

A simple and robust flow injection system which permits low sample and reagent consumption is described for rapid and reliable hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth. The system, which composed of one peristaltic pump and one four channel solenoid valve, used water as the carrier streams for both sample and NaBH₄ solution. Rapid off-line pre-reduction of the analytes was achieved by using hydroxylamine hydrochloride for selenium and a mixture of potassium iodide and ascorbic acid for arsenic and bismuth. Transition metal interference was eliminated with the addition of thiourea and EDTA into the NaBH₄ solution and significant sensitivity enhancement was observed for selenium in the presence of thiourea in the reductant solution. Under optimised conditions, the method achieved detection limits of 0.2 ng mL⁻¹ for Se, 0.5 ng mL⁻¹ for As and 0.3 ng mL⁻¹ for Bi. The method was very reproducible, achieving relative standard deviations of 6.3% for Se, 3.6% for As and 4.7% for Bi, and has a sample throughput of 360 h⁻¹. Successful application of the method to the quantification of selenium, arsenic and bismuth in a certified reference river sediment sample is reported.     

Rapid and direct speciation of methyltins in seawater by an on-line coupled high performance liquid chromatography-hydride generation-ICP/MS system

A novel on-line coupled HPLC-hydride generation (HG)-ICP/MS system was developed for rapid, direct and sensitive speciation of methyltins in seawater without any pretreatment step. Methyltin compounds were separated by reversed phase HPLC, and then on-line reacted with potassium borohydride and acetic acid to generate volatile hydride products. The volatile derivatization products were separated in the spray chamber of ICP/MS and then introduced into ICP/MS by argon gas for detection. Monomethyltin (MMT), dimethyltin (DMT) and trimethyltin (TMT) were baseline separated in less than 15 min by reversed phase HPLC. The influence of KBH₄ concentration and type of acid on the system performance was investigated and optimized. Calibration curves, based on peak heights against concentration, were linear in the range of 0.5-50 ng (Sn) mL⁻¹ of methyltins with correlation coefficients of 0.9990, 0.9990 and 0.9996 for MMT, DMT and TMT, respectively. The relative standard deviations measured at 10 ng (Sn) mL⁻¹ for these three methyltins were in the range of 0.6-1.4% (n = 5), and the calculated detection limits (S/N = 3) for MMT, DMT and TMT were 0.266, 0.095 and 0.039 ng (Sn) mL⁻¹, respectively. This method was successfully applied to the speciation of methyltins in seawater with spiked recovery in the range of 95.4-106.9%. MMT and DMT were detected in all the seawater samples with concentrations in the range of 1.0-1.5 and 0.30-0.57 ng (Sn) mL⁻¹ for MMT and DMT, respectively.     

Speciation of silicon and phosphorous using liquid chromatography coupled with sector field high resolution ICP-MS

Sector-field high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) has been used, at R=3000, to resolve spectral interferences caused by N₂⁺ and CO⁺ on ²⁸Si⁺, and NOH⁺ and NO⁺ on ³¹P⁺, thereby facilitating the speciation of these elements. Polydimethylsiloxanes (PDMS), ranging from 162 g mol⁻¹ to 16 500 g mol⁻¹, and their silanol breakdown products, have been separated by size exclusion and reverse phase chromatography, respectively, and detected using HR-ICP-MS. Detection limits (as Si) of between 12–30 ng ml⁻¹ and 0.1–4 ng ml⁻¹ were obtained for the PDMS and silanol compounds, respectively. Quantitative and reproducible methods have been developed for the analysis of four common organophosphorous pesticides in blood plasma, and inorganic phosphates in food, with detection limits of between 0.9–2 ng ml⁻¹ and 1–39 ng ml^−1, respectively.     

Determination of selenium in water and soil by hydride generation atomic absorption spectrometry using solid reagents

A hydride generation method for the determination of traces of selenium at ng mL⁻¹ concentration ranges has been introduced using a solid mixture of tartaric acid and sodium tetrahydroborate. Atomic absorption spectrometry (AAS) has been used as the detection system. Several parameters such as the ratio of tartaric acid to sodium tetrahydroborate, type and amount of acid, and the reaction temperature were optimized by using 640 ng mL⁻¹ (16 ng per 25 μL) of Se(IV) standard solution. The calibration curve was linear from 20 to 1200 ng mL⁻¹ (0.5-30 ng Se(IV) per 25 μL). The relative standard deviation (%R.S.D.) of the determination was 1.93% and the detection limit was 10.6 ng mL⁻¹ (265 pg per 25 μL) of Se(IV). The reliability of the method was checked using different types of environmental samples, such as several types of water, a sample of soil and also in a kind of calcium phosphate sample by standard addition method. For conversion of Se(VI) present in real samples to Se(IV), l-cysteine was added to NaBH₄ and tartaric acid mixture. The results showed good agreement between this method and other hydride generation techniques.     

Simultaneous determination of arsenic, antimony and selenium by gas-phase diode array molecular absorption spectrometry, after preconcentration in a cryogenic trap

This paper describes a method for the simultaneous determination of As(III), Sb(III) and Se(IV) by combining hydride generation and gas phase molecular absorption spectrometry. A system for continuous hydride generation has been designed and developed, based on the use of a double process of gas-liquid separation, and optimal compromise operation conditions for the three compounds have been found. After generation, the hydrides are collected in a liquid nitrogen cryogenic trap, and then evaporated and driven to the flow cell of a diode array spectrophotometer, in which the transient signals over the 190–250 nm wavelength interval are measured. Under the recommended conditions (sample flow: 35 ml min⁻¹, 0.5 M HCl; reductor flow: 4 ml min⁻¹ of 4% NaBH₄, solution) linear response ranges above 50 μg 1⁻¹ for As(III), 30 μg 1⁻¹ for Sb(III) and 200 μg 1⁻¹ for Se(IV) are obtained with detection limits of 22 μg 1⁻¹, 15 μg 1⁻¹ and 65 μg 1⁻¹, respectively. Multiwavelength linear regression equations were used for the simultaneous determination of the three elements in different synthetic samples, with good precision and accuracy and to study simultaneously the interference from different chemical species for the three compounds. Results were similar to those obtained by other techniques using hydride generation.     

Simultaneous determination of cobalt and chromium by ion chromatography with chemiluminescence detection and its application to glass analysis

A method is described for the simultaneous determination of very low levels of Co and Cr by high performance ion chromatography coupled with a chemiluminescence detection system. 0.1M K₂SO₄ solutions, adjusted to pH 3.0, were used as eluent to separate Co(II) and Cr(III) between them and from interferents. The detection system was the chemiluminescence of luminol/ H₂O₂ in alkaline medium catalyzed by such transition metals. Using a matrix solution analogous to soda-lime silica glass (dissolved in acids) calibration graphs were linear up to 0.5 ng ml^–1 for cobalt and up to 250 ng ml^–1 for chromium. The corresponding calculated detection limits (3 s) in such matrix were 0.05 ng ml^–1 and 15 ng ml^–1 for Co and Cr, respectively. The relative standard deviations were 1.4% at 0.5 ng ml^–1 Co level and 2.8% at the 200 ng ml^–1 Cr level. No interferences were observed from the more common metals, particularly those present in glass samples. The ion chromatography/ chemiluminescent method proposed has been successfully applied to the analysis of Co and Cr in glasses.     

Inductively coupled plasma mass spectrometry for stable isotope tracer investigations

Inductively coupled plasma mass spectrometry (ICP-MS) has now been developed for application to stable isotope tracer investigations of several minerals/trace elements. Use of this method for such purposes requires an understanding of a number of fundamental issues: analytical chemistry performance of the method of isotopic analysis, relationship of the level of enriched isotope administered to the subject with background level of the isotope already present, the issues of cost, and finally the specific details of the biological issues to be explored.In this paper, a brief discussion of these issues is presented. As an example, the discussion is presented in relation to selected aspects of metabolism of selenium, employing the three stable isotopes⁷⁴Se,⁷⁷Se, and⁸²Se in the rat as the biological model.Analytical performance of hydride generation/ICP-MS is discussed for the required analyses of selenium isotopes. It is shown that for solutions containing 10 ng/ml Se of natural isotopic composition, optimized signal/background ratios greater than 40/1 can be obtained, resulting in worst-case detection limits (ng Se) of 2 (⁷⁴Se), and 0.6 (^77,82Se). The precision and accuracy of isotope ratio measurements for the method used routinely in biological studies is 1%. The accuracy of the method for quantitative isotopic analysis is compared with hydride generation/atomic absorption spectrophotometry (HG/AAS). The following results are given (g Se/g or ml; mean + 1 SD,n = 3–5; first HG/ICP-MS, second HG/AAS): SRM 1577a [bovine liver] 0.697 ± 0.002 versus 0.69 ± 0.01; human blood plasma 0.098 ± 0.001 versus 0.135 ± 0.008; human red cells 0.211 ± 0.002 versus 0.216 ± 0.012; and human urine 0.0473 ± 0.0003 versus 0.0489 ± 0.0003.An experiment is described with the rat to show the feasibility of the method for studies of selenium metabolism. Rats were placed on Se-free diet for eight weeks, given their Se requirements in the drinking water in the form of⁷⁶SeO ₃ ^2– and a single-day (day 3) replacement of their water with that containing highly enriched⁷⁴SeO ₃ ^2– . Isotopic analysis of carcass and selected organs revealed a high degree of isotopic enrichment with respect to⁷⁴Se during the entire eight weeks of the experiment, indicating the feasibility of this approach for detailed investigations of selenium metabolism in the rat.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

Determination of lead by hydride generation inductively coupled plasma mass spectrometry (HG-ICP-MS): On-line generation of plumbane using potassium hexacyanomanganate(III)

A hydride generation (HG) procedure has been described for determination of Pb by ICP-MS using potassium hexacyanomanganate(III), K₃Mn(CN)₆, as an additive to facilitate the generation of plumbane (PbH₄). Potassium hexacyanomanganate(III) was prepared in acidic medium as it was unstable in water. The stability of hexacyanomanganate(III) was examined in dilute solutions of HCl, HNO₃ and H₂SO₄. The solutions prepared in 1% v/v H₂SO₄ were found to be stable for over a period of 24 h. The least suitable medium was 1% v/v HNO₃. For generation of plumbane, acidic hexacyanomanganate(III) and sample solutions were mixed on-line along a 5-cm long tygon tubing (1.14 mm i.d.) and then reacted with 2% m/v sodium borohydride (NaBH₄). A concentration of 0.5% m/v K₃Mn(CN)₆ facilitated the generation of PbH₄ remarkably. In comparison to H₂SO₄, HCl provided broader working range for which optimum concentration was 1% v/v. No significant interferences were noted from transition metals and hydride forming elements, up to 0.5 μg mL⁻¹ levels, except Cu which depressed the signals severely. The depressive effects in the presence of 0.1 μg mL⁻¹ Cu were alleviated by increasing the concentration of K₃Mn(CN)₆ to 2% m/v. Under these conditions, the sensitivity was enhanced by a factor of at least 42 to 48. The detection limit (3 s) was 0.008 μg L⁻¹ for ²⁰⁸Pb isotope. Average signal-to-noise ratio (S/N) ranged between 18 and 20 for 1.0 μg mL⁻¹ Pb solution. The accuracy of the method was verified by analysis of several certified reference materials, including Nearshore seawater (CASS-4), Bone ash (SRM 1400), and Mussel tissue (SRM 2976). The procedure was also successfully applied to the determination of Pb in coastal seawater samples by ICP-MS.     

Hydride generation atomic fluorescence spectrometric determination of ultratraces of selenium and tellurium in cow milk

A sensitive procedure has been developed for selenium and tellurium determination in milk by hydride generation atomic fluorescence spectrometry (HG-AFS) after microwave-assisted sample digestion. The method provides sensitivity values of 1591 and 997 fluorescence units ng⁻¹ ml⁻¹ with detection limits of 0.005 and 0.015 ng ml⁻¹ for Se and Te, respectively. The application of the developed methodology to the analysis of cow milk samples of the Spanish market evidenced the presence of concentration ranges from 11.1 to 26.0 ng ml⁻¹ for Se, and from 1.04 to 9.7 ng ml⁻¹ for Te having found a good comparability with data obtained after dry-ashing of samples.     

Determination of tributyltin in sediments by hydride generation /GC/QFAAS

All steps involved in the determination of tributyltin in sediments by anhydrous acetic acid extraction, hydride generation, cold trapping, gas chromatographic separation and quartz furnace atomic absorption spectrometry are critically examined. Detection limits (1.8 ng Sn.g^–1) and reproducibility at representative concentration levels (6–12%) are satisfying for practical purposes.     

Determination of bismuth in solid samples by hydride generation atomic fluorescence spectrometry with a dielectric barrier discharge atomizer

An atmospheric pressure dielectric barrier discharge (DBD) atomizer was investigated for bismuth (Bi) determination with hydride generation (HG) atomic fluorescence spectrometry (AFS). The characteristics of the atomizer and the effects of experimental parameters, including observation height, discharge power, flow rate of discharge gas and AFS carrier gas were optimized. The linear range of present method for Bi determination is 0.5-300.0 μg L⁻¹ with a detection limit of 0.07 μg L⁻¹ (3σ). The method was validated by the analysis of reference materials (GBW08517 and GSB-14) and the results agreed well with the reference values. The established method was applied to the determination of Bi in ore, soil and ash samples.     

Electrochemical hydride generation atomic absorption spectrometry for determination of cadmium

An electrolytic hydride generation system for determination of another hydride forming element, cadmium, by catholyte variation electrochemical hydride generation (EcHG) atomic absorption spectrometry is described. A laboratory-made electrolytic cell with lead-tin alloy as cathode material is designed as electrolytic generator of molecular hydride. The influences of several parameters on the analytical signal have been evaluated using a Plackett-Burman experimental design. The significant parameters such as cathode surface area, electrolytic current, carrier gas flow rate and catholyte concentration have been optimized using univariate method. The analytical figures of merit of procedure developed were determined. The calibration curve was linear up to 20 ng ml⁻¹of cadmium. The concentration detection limit (3σ, n = 8) of 0.2 ng ml⁻¹ and repeatability (relative standard deviation, n = 7) of 3.1% were achieved at 10.0 ng ml⁻¹. It was shown that interferences from major constituents at high concentrations were significant. The accuracy of method was verified using a real sample (spiked tap water) by standard addition calibration technique. Recovery of 104% was achieved for Cd in the spiked tap water sample.