Effects of CO<Subscript>2</Subscript> Compressibility on CO<Subscript>2</Subscript> Storage in Deep Saline Aquifers

The injection of supercritical CO₂ in deep saline aquifers leads to the formation of a CO₂ plume that tends to float above the formation brine. As pressure builds up, CO₂ properties, i.e. density and viscosity, can vary significantly. Current analytical solutions do not account for CO₂ compressibility. In this article, we investigate numerically and analytically the effect of this variability on the position of the interface between the CO₂-rich phase and the formation brine. We introduce a correction to account for CO₂ compressibility (density variations) and viscosity variations in current analytical solutions. We find that the error in the interface position caused by neglecting CO₂ compressibility is relatively small when viscous forces dominate. However, it can become significant when gravity forces dominate, which is likely to occur at late times of injection.     

Buoyancy Effects on Upward Brine Displacement Caused by CO2 Injection

Upward displacement of brine from deep reservoirs driven by pressure increases resulting from CO₂ injection for geologic carbon sequestration may occur through improperly sealed abandoned wells, through permeable faults, or through permeable channels between pinch-outs of shale formations. The concern about upward brine flow is that, upon intrusion into aquifers containing groundwater resources, the brine may degrade groundwater. Because both salinity and temperature increase with depth in sedimentary basins, upward displacement of brine involves lifting fluid that is saline but also warm into shallower regions that contain fresher, cooler water. We have carried out dynamic simulations using TOUGH2/EOS7 of upward displacement of warm, salty water into cooler, fresher aquifers in a highly idealized two-dimensional model consisting of a vertical conduit (representing a well or permeable fault) connecting a deep and a shallow reservoir. Our simulations show that for small pressure increases and/or high-salinity-gradient cases, brine is pushed up the conduit to a new static steady-state equilibrium. On the other hand, if the pressure rise is large enough that brine is pushed up the conduit and into the overlying upper aquifer, flow may be sustained if the dense brine is allowed to spread laterally. In this scenario, dense brine only contacts the lower-most region of the upper aquifer. In a hypothetical case in which strong cooling of the dense brine occurs in the upper reservoir, the brine becomes sufficiently dense that it flows back down into the deeper reservoir from where it came. The brine then heats again in the lower aquifer and moves back up the conduit to repeat the cycle. Parameter studies delineate steady-state (static) and oscillatory solutions and reveal the character and period of oscillatory solutions. Such oscillatory solutions are mostly a curiosity rather than an expected natural phenomenon because in nature the geothermal gradient prevents the cooling in the upper aquifer that occurs in the model. The expected effect of upward brine displacement is either establishment of a new hydrostatic equilibrium or sustained upward flux into the bottom-most region of the upper aquifer.     

Modeling of CO<Subscript>2</Subscript> Leakage up Through an Abandoned Well from Deep Saline Aquifer to Shallow Fresh Groundwaters

This article presents a numerical modeling application using the code TOUGHREACT of a leakage scenario occurring during a CO₂ geological storage performed in the Jurassic Dogger formation in the Paris Basin. This geological formation has been intensively used for geothermal purposes and is now under consideration as a site for the French national program of reducing greenhouse gas emissions and CO₂ geological storage. Albian sandstone, situated above the Dogger limestone is a major strategic potable water aquifer; the impacts of leaking CO₂ due to potential integrity failure have, therefore, to be investigated. The present case–study illustrates both the capacity and the limitations of numerical tools to address such a critical issue. The physical and chemical processes simulated in this study have been restricted to: (i) supercritical CO₂ injection and storage within the Dogger reservoir aquifer, (ii) CO₂ upwards migration through the leakage zone represented as a 1D vertical porous medium to simulate the cement–rock formation interface in the abandoned well, and (iii) impacts on the Albian aquifer water quality in terms of chemical composition and the mineral phases representative of the porous rock by estimating fluid–rock interactions in both aquifers. Because of CPU time and memory constraints, approximation and simplification regarding the geometry of the geological structure, the mineralogical assemblages and the injection period (up to 5 years) have been applied to the system, resulting in limited analysis of the estimated impacts. The CO₂ migration rate and the quantity of CO₂ arriving as free gas and dissolving, firstly in the storage water and secondly in the water of the overlying aquifer, are calculated. CO₂ dissolution into the Dogger aquifer induces a pH drop from about 7.3 to 4.9 limited by calcite dissolution buffering. Glauconite present in the Albian aquifer also dissolves, causing an increase of the silicon and aluminum in solution and triggering the precipitation of kaolinite and quartz around the intrusion point. A sensitivity analysis of the leakage rate according to the location of the leaky well and the variability of the petro-physical properties of the reservoir, the leaky well zone and the Albian aquifers is also provided.     

New Trapping Mechanism in Carbon Sequestration

The modes of geologic storage of CO₂ are usually categorized as structural, dissolution, residual, and mineral trapping. Here we argue that the heterogeneity intrinsic to sedimentary rocks gives rise to a fifth category of storage, which we call local capillary trapping. Local capillary trapping occurs during buoyancy-driven migration of bulk phase CO₂ within a saline aquifer. When the rising CO₂ plume encounters a region (10⁻² to 10⁺¹m) where capillary entry pressure is locally larger than average, CO₂ accumulates beneath the region. This form of storage differs from structural trapping in that much of the accumulated saturation will not escape, should the integrity of the seal overlying the aquifer be compromised. Local capillary trapping differs from residual trapping in that the accumulated saturation can be much larger than the residual saturation for the rock. We examine local capillary trapping in a series of numerical simulations. The essential feature is that the drainage curves (capillary pressure versus saturation for CO₂ displacing brine) are required to be consistent with permeabilities in a heterogeneous domain. In this work, we accomplish this with the Leverett J-function, so that each grid block has its own drainage curve, scaled from a reference curve to the permeability and porosity in that block. We find that capillary heterogeneity controls the path taken by rising CO₂. The displacement front is much more ramified than in a homogeneous domain, or in a heterogeneous domain with a single drainage curve. Consequently, residual trapping is overestimated in simulations that ignore capillary heterogeneity. In the cases studied here, the reduction in residual trapping is compensated by local capillary trapping, which yields larger saturations held in a smaller volume of pore space. Moreover, the amount of CO₂ phase remaining mobile after a leak develops in the caprock is smaller. Therefore, the extent of immobilization in a heterogeneous formation exceeds that reported in previous studies of buoyancy-driven plume movement.     

Analytical Model for CO2 Injection into Brine Aquifers-Containing Residual CH4

During CO₂ injection into brine aquifers-containing residual and/or dissolved CH₄, three distinct regions develop: (1) a single-phase, dry-out region around the well-bore filled with pure supercritical CO₂; (2) a two-phase, two-component system containing CO₂ and brine; and (3) a two-phase, two-component system containing CH₄, and brine. This article extends an existing analytical solution, for pressure buildup during CO₂ injection into brine aquifers, by incorporating dissolved and/or residual CH₄. In this way, the solution additionally accounts for partial miscibility of the CO₂?CCH₄?Cbrine system and the relative permeability hysteresis associated with historic imbibition of brine and current drainage due to CO₂ injection and CH₄ bank development. Comparison of the analytical solution results with commercial simulator, CMG-GEM, shows excellent agreement among a range of different scenarios. The presence of residual CH₄ in a brine aquifer summons two competing phenomena, (1) reduction in relative permeability (phase interference), which increases pressure buildup by reducing total mobility, and (2) increase in bulk compressibility which decreases pressure buildup of the system. If initial CH₄ is dissolved (no free CH₄), these effects are not as important as they are in the residual gas scenario. Relative permeability hysteresis increased the CH₄ bank length (compared to non-hysteretic relative permeability), which led to further reduction in pressure buildup. The nature of relative permeability functions controls whether residual CH₄ is beneficial or disadvantageous to CO₂ storage capacity and injectivity in a candid brine aquifer.     

The Footprint of the CO<Subscript>2</Subscript> Plume during Carbon Dioxide Storage in Saline Aquifers: Storage Efficiency for Capillary Trapping at the Basin Scale

We study a sharp-interface mathematical model of CO₂ migration in deep saline aquifers, which accounts for gravity override, capillary trapping, natural groundwater flow, and the shape of the plume during the injection period. The model leads to a nonlinear advection–diffusion equation, where the diffusive term is due to buoyancy forces, not physical diffusion. For the case of interest in geological CO₂ storage, in which the mobility ratio is very unfavorable, the mathematical model can be simplified to a hyperbolic equation. We present a complete analytical solution to the hyperbolic model. The main outcome is a closed-form expression that predicts the ultimate footprint on the CO₂ plume, and the time scale required for complete trapping. The capillary trapping coefficient and the mobility ratio between CO₂ and brine emerge as the key parameters in the assessment of CO₂ storage in saline aquifers. Despite the many approximations, the model captures the essence of the flow dynamics and therefore reflects proper dependencies on the mobility ratio and the capillary trapping coefficient, which are basin-specific. The expressions derived here have applicability to capacity estimates by capillary trapping at the basin scale.     

Linear Stability Analysis of Double-Diffusive Convection in Porous Media,with Application to Geological Storage of CO<Subscript>2</Subscript>

Onset of double-diffusive buoyancy-driven flow resulted from vertical temperature and concentration gradients in a horizontal layer of a saturated and homogenous porous medium is investigated using amplification factor theory. After injection of CO₂ into a deep saline aquifer, the density of the brine saturated with CO₂ increases slightly. This increase in density induces natural convection. The effect of geothermal gradient is also considered in this work as a second incentive for convection and the double-diffusion convection was studied. Linear stability analysis is used to predict the inception of instabilities and initial wavelength of the convective instabilities. The analysis presented is applied to acid gas injection (as an analogue for CO₂ storage) into saline aquifers in the Alberta basin. It is found that the geothermal gradient does not have significant effect on the onset of convection for these aquifers. It is shown that the geothermal effects on the onset of natural convection are negligible as compared to the solutal effects induced by dissolution and diffusion of CO₂ in deep saline aquifers. Therefore, the linear stability analysis and the long-term numerical simulation of CO₂ sequestration into such saline aquifers may be assumed to be isothermal in terms of natural convection occurrence.     

Characteristics of Salt-Precipitation and the Associated Pressure Build-Up during CO<Subscript>2</Subscript> Storage in Saline Aquifers

Mitigation and control of borehole pressure at the bottom of an injection well is directly related to the effective management of well injectivity during geologic carbon sequestration activity. Researchers have generally accepted the idea that high rates of CO₂ injection into low permeability strata results in increased bottom-hole pressure in a well. However, the results of this study suggested that this is not always the case, due to the occurrence of localized salt precipitation adjacent to the injection well. A series of numerical simulations indicated that in some cases, a low rate of CO₂ injection into high permeability formation induced greater pressure build-up. This occurred because of the different types of salt precipitation pattern controlled by buoyancy-driven CO₂ plume migration. The first type is non-localized salt precipitation, which is characterized by uniform salt precipitation within the dry-out zone. The second type, localized salt precipitation, is characterized by an abnormally high level of salt precipitation at the dry-out front. This localized salt precipitation acts as a barrier that hampers the propagation of both CO₂ and pressure to the far field as well as counter-flowing brine migration toward the injection well. These dynamic processes caused a drastic pressure build-up in the well, which decreased injectivity. By modeling a series of test cases, it was found that low-rate CO₂ injection into high permeability formation was likely to cause localized salt precipitation. Sensitivity studies revealed that brine salinity linearly affected the level of salt precipitation, and that vertical permeability enhanced the buoyancy effect which increased the growth of the salt barrier. The porosity also affected both the level of localized salt precipitation and dry-out zone extension depending on injection rates. High temperature injected CO₂ promoted the vertical movement of the CO₂ plume, which accelerated localized salt precipitation, but at the same time caused a decrease in the density of the injected CO₂. The combination of these two effects eventually decreased bottomhole pressure. Considering the injectivity degradation, a method is proposed for decreasing the pressure build-up and increasing injectivity by assigning a ‘skin zone’ that represents a local region with a transmissivity different from that of the surrounding aquifer.     

CO2 Plume Evolution and Pressure Buildup of Large-scale CO2 Injection into Saline Aquifers in Sanzhao Depression, Songliao Basin, China

Large-scale injection of carbon dioxide (CO₂) into saline aquifers in sedimentary basins is a promising approach to mitigate global climate change. Songliao Basin, a large continental clastic sedimentary basin in northeastern China, is one of the great potential candidate sites for future CO₂ storage in China. In this paper, a three-dimensional CO₂ storage model was built to evaluate the CO₂ plume evolution and pressure buildup of large-scale CO₂ injection into the saline aquifers in the Sanzhao Depression of the Songliao Basin. CO₂ was injected into the aquifers through five wells, each with an annual injection rate of 3 Mt over 50?years. The results show that the clastic Yaojia formation at the depth between 900 and 1,600 m with thickness of 150 m might be the favorable layer to store a considerable amount of CO₂, and the overlying Nenjiang formation could ensure long-term CO₂ containment. The relative low permeability of the upper part of the Yaojia formation seems to play a role of a secondary seal on carbon storage. In current injection scenario, CO₂ plume migrates into the formations in the southeast of the depression, which could have potential risk of polluting the freshwater. Therefore, the injection site should stay far away from the southeast of the depression. Moreover, it is very crucial to investigate the permeability distribution of the Yaojia formation because it significantly dominates the CO₂ plume migration. After only 6?months of injection, the pressure buildup at each injection site is affected by pressure interference from neighboring sites. The maximum pressure buildup in the formations is 7.8?MPa after 50?years of injection, and it can even reach 10.5?MPa when the injection layers are with lower permeability. The maximum pressure buildup at the bottom of the Nenjiang formation is 6.7?MPa. The gradient of maximum limited formation pressure is about 18?MPa/km, which might cause fractures to open in the formations of the Sanzhao Depression. Continuous injection of CO₂ for 50?years may not cause damage to the caprock even when the lower permeability occurred in the upper part of the Yaojia formation. The safety of CO₂ storage will be enhanced if the upper part of the storage formation has lower permeability than the lower part.     

Coreflooding Studies to Investigate the Potential of Carbonated Water Injection as an Injection Strategy for Improved Oil Recovery and CO<Subscript>2</Subscript> Storage

Carbonated water injection (CWI) is a CO₂-augmented water injection strategy that leads to increased oil recovery with added advantage of safe storage of CO₂ in oil reservoirs. In CWI, CO₂ is used efficiently (compared to conventional CO₂ injection) and hence it is particularly attractive for reservoirs with limited access to large quantities of CO₂, e.g. offshore reservoirs or reservoirs far from large sources of CO₂. We present the results of a series of CWI coreflood experiments using water-wet and mixed-wet Clashach sandstone cores and a reservoir core with light oil (n-decane), refined viscous oil and a stock-tank crude oil. The experiments were carried out to assess the performance of CWI and to quantify the level of additional oil recovery and CO₂ storage under various experimental conditions. We show that the ultimate oil recovery by CWI is higher than the conventional water flooding in both secondary and tertiary recovery methods. Oil swelling as a result of CO₂ diffusion into the oil and the subsequent oil viscosity reduction and coalescence of the isolated oil ganglia are amongst the main mechanisms of oil recovery by CWI that were observed through the visualisation experiments in high-pressure glass micromodels. There was also evidence of a change in the rock wettability that could also influence the oil recovery. The coreflood test results also reveal that the CWI performance is influenced by oil viscosity, core wettability and the brine salinity. Higher oil recovery was obtained with the mixed-wet core than the water-wet core, with light oil than with the viscous oil and low salinity carbonated brine than high-salinity carbonated brine. At the end of the flooding period, an encouraging amount of the injected CO₂ was stored in the brine and the remaining oil in the form of stable dissolved CO₂. The experimental results clearly demonstrate the potential of CWI for improving oil recovery as compared with the conventional water flooding (secondary recovery) or as a water-based EOR (enhanced oil recovery) method for watered out reservoirs.     

Numerical Simulation Studies of the Long-term Evolution of a CO<Subscript>2</Subscript> Plume in a Saline Aquifer with a Sloping Caprock

We have used the TOUGH2-MP/ECO2N code to perform numerical simulation studies of the long-term behavior of CO₂ stored in an aquifer with a sloping caprock. This problem is of great practical interest, and is very challenging due to the importance of multi-scale processes. We find that the mechanism of plume advance is different from what is seen in a forced immiscible displacement, such as gas injection into a water-saturated medium. Instead of pushing the water forward, the plume advances because the vertical pressure gradients within the plume are smaller than hydrostatic, causing the groundwater column to collapse ahead of the plume tip. Increased resistance to vertical flow of aqueous phase in anisotropic media leads to reduced speed of up-dip plume advancement. Vertical equilibrium models that ignore effects of vertical flow will overpredict the speed of plume advancement. The CO₂ plume becomes thinner as it advances, but the speed of advancement remains constant over the entire simulation period of up to 400 years, with migration distances of more than 80 km. Our simulations include dissolution of CO₂ into the aqueous phase and associated density increase, and molecular diffusion. However, no convection develops in the aqueous phase because it is suppressed by the relatively coarse (sub-) horizontal gridding required in a regional-scale model. A first crude sub-grid-scale model was developed to represent convective enhancement of CO₂ dissolution. This process is found to greatly reduce the thickness of the CO₂ plume, but, for the parameters used in our simulations, does not affect the speed of plume advancement.     

Reservoir storage and containment of greenhouse gases

This paper deals with the problem of disposal of industrial waste greenhouse gases (CO₂) into deep reservoirs. The simulator TOUGH2 was used to model the injection of 100 kg/s of CO₂ for 10 years into an aquifer 3 km deep with the object of evaluating the long-term storage prospects for this gas. Depending on the permeability structure above the injection point, some gas may escape to the surface. In the most favourable case, all of the gas dissolves into the water, and the resulting dense fluid settles in the aquifer over several thousand years. Consequently, underground storage provides a promising sink for reducing CO₂ emissions to the atmosphere.     

A Study of Microscale Gas Trapping Using Etched Silicon Micromodels

Immobilization and trapping of carbon dioxide (CO₂) enhances the security of geological storage. Trapping mechanisms have been characterized in four groups: structural, residual, dissolution, and mineralization. While structural trapping acts immediately when injection starts and is well investigated, the contribution of residual and dissolution trapping increases over storage time and these contributions need to be better understood for better predictions. This paper focuses on an experimental pore-scale investigation of residual and capillary trapping. CO₂?Cwater imbibition experiments were conducted in micromodels whose homogenous pore space is geometrically and topologically similar to Berea sandstone. Microvisual data, photographs and video footage, describes the trapping mechanism and, especially, the disconnection and shrinkage of the CO₂ phase. Results show that depending on the flow rate of the imbibing water different trapping mechanisms are observed. Lower flow rates, comparable to the trailing edge of a CO₂ plume, lead to more snap-off events and greater trapped residual saturation, whereas rates comparable to the near wellbore area during enhanced sequestration showed displacement of gas bubbles and greater dissolution that ultimately leads to very low or zero gas saturations. Furthermore, complete dissolution events showed that homogenous as well as heterogeneous dissolution occurs. Whereas the latter is subdivided into microbubble formation and dissolution on crevices or pore roughness, the former occurs without the influence of pore walls. Based on the observations we suggest that the type of rock and its roughness as well as the fines present at the CO₂ brine interface are important factors determining the dissolution mechanism.     

Numerical Simulations of the Thermal Impact of Supercritical CO<Subscript>2</Subscript> Injection on Chemical Reactivity in a Carbonate Saline Reservoir

Geological sequestration of CO₂ offers a promising solution for reducing net emissions of greenhouse gases into the atmosphere. This emerging technology must make it possible to inject CO₂ into deep saline aquifers or oil- and gas-depleted reservoirs in the supercritical state (P > 7.4MPa and T > 31.1°C) to achieve a higher density and therefore occupy less volume underground. Previous experimental and numerical simulations have demonstrated that massive CO₂ injection in saline reservoirs causes a major disequilibrium of the physical and geochemical characteristics of the host aquifer. The near-well injection zone seems to constitute an underground hydrogeological system particularly impacted by supercritical CO₂ injection and the most sensitive area, where chemical phenomena (e.g. mineral dissolution/precipitation) can have a major impact on the porosity and permeability. Furthermore, these phenomena are highly sensitive to temperature. This study, based on numerical multi-phase simulations, investigates thermal effects during CO₂ injection into a deep carbonate formation. Different thermal processes and their influence on the chemical and mineral reactivity of the saline reservoir are discussed. This study underlines both the minor effects of intrinsic thermal and thermodynamic processes on mineral reactivity in carbonate aquifers, and the influence of anthropic thermal processes (e.g. injection temperature) on the carbonates’ behaviour.     

Quantification of Density-Driven Natural Convection for Dissolution Mechanism in CO<Subscript>2</Subscript> Sequestration

Dissolution of CO₂ into brine causes the density of the mixture to increase. The density gradient induces natural convection in the liquid phase, which is a favorable process of practical interest for CO₂ storage. Correct estimation of the dissolution rate is important because the time scale for dissolution corresponds to the time scale over which free phase CO₂ has a chance to leak out. However, for this estimation, the challenging simulation on the basis of convection–diffusion equation must be done. In this study, pseudo-diffusion coefficient is introduced which accounts for the rate of mass transferring by both convection and diffusion mechanisms. Experimental tests in fluid continuum and porous media were performed to measure the real rate of dissolution of CO₂ into water during the time. The pseudo diffusion coefficient of CO₂ into water was evaluated by the theory of pressure decay and this coefficient is used as a key parameter to quantify the natural convection and its effect on mass transfer of CO₂. For each experiment, fraction of ultimate dissolution is calculated from measured pressure data and the results are compared with predicted values from analytical solution. Measured CO₂ mass transfer rate from experiments are in reasonable agreement with values calculated from diffusion equation performed on the basis of pseudo-diffusion coefficient. It is suggested that solving diffusion equation with pseudo diffusion coefficient herein could be used as a simple and rapid tool to calculate the rate of mass transfer of CO₂ in CCS projects.     

Microtomography and Pore-Scale Modeling of Two-Phase Fluid Distribution

Synchrotron-based X-ray microtomography (micro CT) at the Advanced Light Source (ALS) line 8.3.2 at the Lawrence Berkeley National Laboratory produces three-dimensional micron-scale-resolution digital images of the pore space of the reservoir rock along with the spacial distribution of the fluids. Pore-scale visualization of carbon dioxide flooding experiments performed at a reservoir pressure demonstrates that the injected gas fills some pores and pore clusters, and entirely bypasses the others. Using 3D digital images of the pore space as input data, the method of maximal inscribed spheres (MIS) predicts two-phase fluid distribution in capillary equilibrium. Verification against the tomography images shows a good agreement between the computed fluid distribution in the pores and the experimental data. The model-predicted capillary pressure curves and tomography-based porosimetry distributions compared favorably with the mercury injection data. Thus, micro CT in combination with modeling based on the MIS is a viable approach to study the pore-scale mechanisms of CO₂ injection into an aquifer, as well as more general multi-phase flows.     

Analytical Solution Incorporating History-Dependent Processes for Quick Assessment of Capillary Trapping During CO<Subscript>2</Subscript> Geological Storage

Carbon storage in saline formations is considered as a promising option to ensure the necessary decrease of CO₂ anthropogenic emissions. Its industrial development in those formations is above all conditioned by its safety demonstration. Assessing the evolution of trapped and mobile CO₂ across time is essential in the perspective of reducing leakage risks. In this work, we focus on residual trapping phenomenon occurring during the wetting of the injected CO₂ plume. History dependent effects are of first importance when dealing with capillary trapping. We then apply the classical fractional flow theory (Buckley–Leverett type model) and include trapping and hysteresis models; we derive an analytical solution for the temporal evolution of saturation profile and of CO₂ trapped quantity when injecting water after the gas injection (“artificial imbibition”). The comparison to numerical simulations for different configurations shows satisfactory match and justifies, in the case of industrial CO₂ storage, the assumptions of incompressible flow with no consideration of capillary pressure. The obtained analytical solution allows the quick assessment of both the quantity and the location of mobile gas left during imbibition.     

CO<Subscript>2</Subscript> injection into saline carbonate aquifer formations I: laboratory investigation

Although there are a number of mathematical modeling studies for carbon dioxide (CO₂) injection into aquifer formations, experimental studies are limited and most studies focus on injection into sandstone reservoirs as opposed to carbonate ones. This study presents the results of computerized tomography (CT) monitored laboratory experiments to analyze permeability and porosity changes as well as to characterize relevant chemical reactions associated with injection and storage of CO₂ in carbonate formations. CT monitored experiments are designed to model fast near well bore flow and slow reservoir flows. Highly heterogeneous cores drilled from a carbonate aquifer formation located in South East Turkey were used during the experiments. Porosity changes along the core plugs and the corresponding permeability changes are reported for different CO₂ injection rates and different salt concentrations of formation water. It was observed that either a permeability increase or a permeability reduction can be obtained. The trend of change in rock properties is very case dependent because it is related to distribution of pores, brine composition and thermodynamic conditions. As the salt concentration decreases, porosity and the permeability decreases are less pronounced. Calcite deposition is mainly influenced by orientation, with horizontal flow resulting in larger calcite deposition compared to vertical flow.     

Injection and Storage of CO<Subscript>2</Subscript> in Deep Saline Aquifers: Analytical Solution for CO<Subscript>2</Subscript> Plume Evolution During Injection

Injection of fluids into deep saline aquifers is practiced in several industrial activities, and is being considered as part of a possible mitigation strategy to reduce anthropogenic emissions of carbon dioxide into the atmosphere. Injection of CO₂ into deep saline aquifers involves CO₂ as a supercritical fluid that is less dense and less viscous than the resident formation water. These fluid properties lead to gravity override and possible viscous fingering. With relatively mild assumptions regarding fluid properties and displacement patterns, an analytical solution may be derived to describe the space–time evolution of the CO₂ plume. The solution uses arguments of energy minimization, and reduces to a simple radial form of the Buckley–Leverett solution for conditions of viscous domination. In order to test the applicability of the analytical solution to the CO₂ injection problem, we consider a wide range of subsurface conditions, characteristic of sedimentary basins around the world, that are expected to apply to possible CO₂ injection scenarios. For comparison, we run numerical simulations with an industry standard simulator, and show that the new analytical solution matches a full numerical solution for the entire range of CO₂ injection scenarios considered. The analytical solution provides a tool to estimate practical quantities associated with CO₂ injection, including maximum spatial extent of a plume and the shape of the overriding less-dense CO₂ front.     

An Experimental Study of CO<Subscript>2</Subscript> Exsolution and Relative Permeability Measurements During CO<Subscript>2</Subscript> Saturated Water Depressurization

Dissolution of CO₂ into brine is an important and favorable trapping mechanism for geologic storage of CO₂. There are scenarios, however, where dissolved CO₂ may migrate out of the storage reservoir. Under these conditions, CO₂ will exsolve from solution during depressurization of the brine, leading to the formation of separate phase CO₂. For example, a CO₂ sequestration system with a brine-permeable caprock may be favored to allow for pressure relief in the sequestration reservoir. In this case, CO₂-rich brine may be transported upwards along a pressure gradient caused by CO₂ injection. Here we conduct an experimental study of CO₂ exsolution to observe the behavior of exsolved gas under a wide range of depressurization. Exsolution experiments in highly permeable Berea sandstones and low permeability Mount Simon sandstones are presented. Using X-ray CT scanning, the evolution of gas phase CO₂ and its spatial distribution is observed. In addition, we measure relative permeability for exsolved CO₂ and water in sandstone rocks based on mass balances and continuous observation of the pressure drop across the core from 12.41 to 2.76 MPa. The results show that the minimum CO₂ saturation at which the exsolved CO₂ phase mobilization occurs is from 11.7 to 15.5%. Exsolved CO₂ is distributed uniformly in homogeneous rock samples with no statistical correlation between porosity and CO₂ saturation observed. No gravitational redistribution of exsolved CO₂ was observed after depressurization, even in the high permeability core. Significant differences exist between the exsolved CO₂ and water relative permeabilities, compared to relative permeabilities derived from steady-state drainage relative permeability measurements in the same cores. Specifically, very low CO₂ and water relative permeabilities are measured in the exsolution experiments, even when the CO₂ saturation is as high as 40%. The large relative permeability reduction in both the water and CO₂ phases is hypothesized to result from the presence of disconnected gas bubbles in this two-phase flow system. This feature is also thought to be favorable for storage security after CO₂ injection.