From nickel oxalate dihydrate microcubes to NiS<Subscript>2</Subscript> nanocubes for high performance supercapacitors

In this study, NiS₂ nanocubes were successfully synthesized by a novel facile solvothermal method using NiC₂O₄·2H₂O microstructures and used as an electrode for high-performance supercapacitors. The electrochemical properties of the prepared NiS₂ electrode were studied using galvanostatic charge–discharge analysis, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) studies. Its maximum specific capacitance was 2077 F g^?1 at a constant current density of about 0.65 A g^?1. Further, the EIS results confirmed the pseudocapacitive nature of the NiS₂ electrode. The experimental results suggested that the NiS₂ electro-active material demonstrates excellent electrochemical performance with high specific capacitance, low resistance, and excellent cycling stability.     

A Microwave Synthesis of Mesoporous NiCo2O4 Nanosheets as Electrode Materials for Lithium‐Ion Batteries and Supercapacitors

A facile microwave method was employed to synthesize NiCo₂O₄ nanosheets as electrode materials for lithium‐ion batteries and supercapacitors. The structure and morphology of the materials were characterized by X‐ray diffraction, field‐emission scanning electron microscopy, transmission electron microscopy and Brunauer–Emmett–Teller methods. Owing to the porous nanosheet structure, the NiCo₂O₄ electrodes exhibited a high reversible capacity of 891 mA h g^?1 at a current density of 100 mA g^?1, good rate capability and stable cycling performance. When used as electrode materials for supercapacitors, NiCo₂O₄ nanosheets demonstrated a specific capacitance of 400 F g^?1 at a current density of 20 A g^?1 and superior cycling stability over 5000 cycles. The excellent electrochemical performance could be ascribed to the thin porous structure of the nanosheets, which provides a high specific surface area to increase the electrode–electrolyte contact area and facilitate rapid ion transport.     

Electrochemical performance of novel Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> glass-ceramic nanocomposites as electrodes for energy storage devices

The novel Li₃V₂(PO₄)₃ glass-ceramic nanocomposites were synthesized and investigated as electrodes for energy storage devices. They were fabricated by heat treatment (HT) of 37.5Li₂O–25V₂O₅–37.5P₂O₅?mol% glass at 450 °C for different times in the air. XRD, SEM, and electrochemical methods were used to study the effect of HT time on the nanostructure and electrochemical performance for Li₃V₂(PO₄)₃ glass-ceramic nanocomposites electrodes. XRD patterns showed forming Li₃V₂(PO₄)₃ NASICON type with monoclinic structure. The crystalline sizes were found to be in the range of 32–56 nm. SEM morphologies exhibited non-uniform grains and changed with variation of HT time. The electrochemical performance of Li₃V₂(PO₄)₃ glass-ceramic nanocomposites was investigated by using galvanostatic charge/discharge methods, cyclic voltammetry, and electrochemical impedance spectroscopy in 1 M H₂SO₄ aqueous electrolyte. The glass-ceramic nanocomposites annealed for 4 h, which had a lower crystalline size, exhibited the best electrochemical performance with a specific capacity of 116.4 F g^?1 at 0.5 A g^?1. Small crystalline size supported the lithium ion mobility in the electrode by decreasing the ion diffusion pathway. Therefore, the Li₃V₂(PO₄)₃ glass-ceramic nanocomposites can be promising candidates for large-scale industrial applications in high-performance energy storage devices.     

Layered Al‐substituted Cobalt Hydroxides/GO Composites for Electrode Materials of Supercapacitors

In this work, Al‐substituted α‐Co(OH)₂/GO composites with supercapacitive properties were prepared by chemical co‐precipitated method in which cobalt nitrate and aluminum nitrate were used as the raw material, and graphite oxide was employed as carrier. The as‐prepared materials were characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and fourier transform infrared spectroscopy (FT‐IR). Cyclic voltammetry (CV) and galvanostatic charge/discharge measurements showed that the Al‐substituted α‐Co(OH)₂/GO electrode material had excellent electrochemical capacitance. The specific capacitance of 1137 F·g⁻¹ was achieved in 6 mol/L KOH solution at a current density of 1 A·g⁻¹ within a potential range of 0–0.5 V. Moreover, only 12% losses of the initial specific capacitance were found after 500 cycles at a current density of 1 A·g⁻¹.     

Co3O4纳米片的制备及其电化学电容性能

以配位超分子化合物为前驱物,通过液相氧化分解得到了六方形CoOOH纳米片,进而在空气中热处理制得了Co₃O₄纳米片。利用XRD、TEM、FESEM对CoOOH和Co₃O₄纳米片的结构和形貌进行了表征。电化学测试表明,Co₃O₄纳米片电极在6 mol·L^-1 KOH溶液中表现出良好的电化学电容特性,在电流密度为1 A·g^-1其单电极比容量可达到227 F·g^-1。     

Preparation of a NiAl‐Oxide@Polypyrrole Composite for High‐Performance Supercapacitors

A core‐shell NiAlO@polypyrrole composite (NiAlO@PPy) with a 3D “sand rose”‐like morphology was prepared via a facile in situ oxidative polymerization of pyrrole monomer, where the role of PPy coating thickness was investigated for high‐performance supercapacitors. Microstructure analyses indicated that the PPy was successfully coated onto the NiAlO surface to form a core‐shell structure. The NiAlO@PPy exhibited a better electrochemical performance than pure NiAlO, and the moderate thickness of the PPy shell layer was beneficial for expediting the electron transfer in the redox reaction. It was found that the NiAlO@PPy₅ prepared at 5.0 mL L^?1 addition amount of pyrrole monomer demonstrated the best electrochemical performance with a high specific capacitance of 883.2 F g^?1 at a current density of 1 A g^?1 and excellent capacitance retention of 91.82 % of its initial capacitance after 1000 cycles at 3 A g^?1. The outstanding electrochemical performance of NiAlO@PPy₅ were due to the synergistic effect of NiAlO and PPy, where the uniform network‐like PPy shell with the optimal thickness made electrolyte ions more easily accessible for faradic reactions. This work provided a simple approach for designing organic–inorganic core‐shell materials as high‐performance electrode materials for electrochemical supercapacitors.     

Nanostructured Fe2O3–graphene composite as a novel electrode material for supercapacitors

Nanostructured Fe₂O₃–graphene composite was successfully fabricated through a facile solution-based route under mild hydrothermal conditions. Well-crystalline Fe₂O₃ nanoparticles with 30–60?nm in size are highly encapsulated in graphene nanosheet matrix, as demonstrated by various characterization techniques. As electrode materials for supercapacitors, the as-obtained Fe₂O₃–graphene nanocomposite exhibits large specific capacitance (151.8?F?g^?1 at 1?A?g^?1), good rate capability (120?F?g^?1 at 6?A?g^?1), and excellent cyclability. The significantly enhanced electrochemical performance compared with pure graphene and Fe₂O₃ nanoparticles may be attributed to the positive synergetic effect between Fe₂O₃ and graphene. In virtue of their superior electrochemical performance, they will be promising electrode materials for high-performance supercapacitors applications.     

Highly Dispersible Hexagonal Carbon–MoS2–Carbon Nanoplates with Hollow Sandwich Structures for Supercapacitors

MoS₂, a typical layered transition-metal dichalcogenide, is promising as an electrode material in supercapacitors. However, its low electrical conductivity could lead to limited capacitance if applied in electrochemical devices. Herein, a new nanostructure composed of hollow carbon–MoS₂–carbon was successfully synthesized through an l -cysteine-assisted hydrothermal method by using gibbsite as a template and polydopamine as a carbon precursor. After calcination and etching of the gibbsite template, uniform hollow platelets, which were made of a sandwich-like assembly of partial graphitic carbon and two-dimensional layered MoS₂ flakes, were obtained. The platelets showed excellent dispersibility and stability in water, and good electrical conductivity due to carbon provided by the calcination of polydopamine coatings. The hollow nanoplate morphology of the material provided a high specific surface area of 543 m² g⁻¹, a total pore volume of 0.677 cm³ g⁻¹, and fairly small mesopores (≈5.3 nm). The material was applied in a symmetric supercapacitor and exhibited a specific capacitance of 248 F g⁻¹ (0.12 F cm⁻²) at a constant current density of 0.1 A g⁻¹; thus suggesting that hollow carbon–MoS₂–carbon nanoplates are promising candidate materials for supercapacitors.     

Non‐Covalent Functionalization of Graphene with Bisphenol A for High‐Performance Supercapacitors

The reduced graphene oxide (RGO)/bisphenol A (BPA) composites were prepared by an adsorption‐reduction method. The composites are characterized by X‐ray diffraction (XRD), UV‐vis, thermogravimetric (TG) analysis, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM). The results confirm that BPA is adsorbed on the basal plane of RGO by π‐π stacking interaction. Furthermore, the electrochemical behaviors were evaluated by cyclic voltammetry, galvanostatic charge/discharge techniques and electrochemical impedance spectroscopy (EIS). The results show that the RGO/BPA nanocomposites exhibit ultrahigh specific capacitance of 466 F·g^?1 at a current density of 1 A·g^?1, excellent rate capability (more than 81% retention at 10 A·g^?1 relative to 1 A·g^?1) and superior cycling stability (90% capacitance decay after 4000 cycles). Consequently, the RGO/BPA nanocomposites can be regarded as promising electrode materials for supercapacitor applications.     

One-step synthesis of nitrogen-doped porous carbon for supercapacitors utilizing KNO<Subscript>3</Subscript> as an electrolyte

Nitrogen-doped porous carbons were prepared using a facile method, with low-biotechnology fulvic acid potassium salts as a precursor. The prepared carbons had a high surface area (1623 m² g^?1) and good electrochemical properties, making them suitable electrode materials for supercapacitors. Nitrogen-doped porous carbons were tested as an electrode in both 6 M KOH aqueous solution and different concentrations KNO₃ aqueous solution. The nitrogen-doped porous carbons with unique microstructure and nitrogen functionalities exhibited a capacitance of 235 F g^?1 in a 6 M KOH aqueous solution. Electrochemical investigation showed that the nitrogen-doped porous carbons exhibited a broad potential operational window in a 2.5 M KNO₃ aqueous solution. Furthermore, a high capacitance retention of 88.1 % was achieved even after 5000 cycles at 1.7 V. Potassium nitrate solutions in a wide range of concentrations were also proven to be promising electrolytes for electrochemical capacitors because they are cheap, noncorrosive, electrochemically stable, and compatible to diverse current collectors.     

High performance pliable supercapacitor fabricated using activated carbon nanospheres intercalated into boron nitride nanoplates by pulsed laser ablation technique

Pliable supercapacitor, yielding specific capacitance (C_s) and energy density as high as 348 F g⁻¹ and 48.3 Wh Kg⁻¹ respectively was fabricated using modified activated carbon electrodes. The nanospheres of activated carbon (AC) were anchored on the nanoplates of boron nitride (BN) by employing the facile technique of pulsed laser ablation in liquid (PLAL) using 532 nm focused laser beam. Four different variants of electrode materials were synthesized by varying the weight percentage (1%, 3%, 5% and 10%) of BN in AC in the PLAL precursor solution. The morphological characteristics, the elemental composition and the structural analysis of the synthesized electrode materials were studied respectively by FESEM, XPS and XRD. The morphological studies indicated that the PLAL synthesis of the electrode materials resulted in proper intercalation of carbon nanospheres into BN nanoplates, which resulted in the observed enhanced performance of the fabricated supercapacitor. Four supercapacitors in this work were fabricated using the four variants of synthesized electrode materials in conjunction with gel polymer electrolyte (GPE). GPE are well known for their non-corrosive nature and best sealing ability to avoid any leakage that results in increasing the cycle life of the device. The performance of the fabricated supercapacitors was evaluated using cyclic voltammetry (CV), galvanostatic charge discharge (GCD) measurement and electrochemical impedance spectroscopy (EIS). The results indicate that the supercapacitor fabricated using 3% BN in AC as electrode material manifested the best specific capacitance and energy density. Also it was found that the supercapacitor maintained 85% of its initial capacitance even after 5000 charge/discharge cycles.     

Highly stable asymmetric supercapacitors based on Ni(OH)<Subscript>2</Subscript> deposited on electro-etched carbon paper

Herein, we introduce the application of nickel hydroxide nanosheets on the electro-etched carbon fiber (ECF) formed via a direct electrodeposition, for fabrication of asymmetric supercapacitor. To confirm the practical applicability of prepared Ni(OH)₂–ECF, an asymmetric device was assembled using Ni(OH)₂–ECF in combination with an activated carbon (AC) electrode. Our results showed a substantial cycling stability (96% capacitance retention after 10000 cycles) and considerable rate capability at large discharge currents (60% capacitance retention at 8 A g^??1) for this asymmetric supercapacitor that may have originated from the good contact between Ni(OH)₂ and ECF. A maximum specific capacitance of 88.1 F g^??1 was achieved for Ni(OH)₂–ECF//AC/CF device and showed considerable rate capability at large discharge currents (60% capacitance retention at 8 A g^??1). The results of this study suggest the Ni(OH)₂–ECF electrode is an excellent material for fabrication of supercapacitor electrodes.     

One-Pot Hydrothermal Synthesis of Ternary 1T-MoS2/Hexa-WO3/Graphene Composites for High-Performance Supercapacitors

A new ternary composite of 1T-molybdenum disulfide, hexagonal tungsten trioxide, and reduced graphene oxide (M-W-rGO) is synthesized by using a one-pot hydrothermal process. The synergetic effect of 1T-MoS₂ and hexa-WO₃ nanoflowers improves the electrochemical performance for supercapacitors by inducing additional active sites and hexagonal tunnels, respectively, which lead to high storage capacity and easy transfer of electrolyte ions. The ternary M-W-rGO composite has a high specific capacitance of 836 F g⁻¹ at 1 A g⁻¹, which is nearly twice that of binary composites of M-rGO and W-rGO with high capacitance retention of 86.35 % after 3000 cycles at a high current density of 5 A g⁻¹. This study provides a new ternary composite that can be used as an electrode material for high-performance supercapacitors.     

A hexaazatriphenylene-based porous organic polymer for high performance supercapacitor

Porous organic polymers (POPs) with high physiochemical stability and pseudocapacitive activity are crucial for supercapacitors with high specific capacitance and long cycle life. We report herein a hexaazatrinaphthylene-based POP (HPOP-1) for high-performance supercapacitor by introducing redox-active hexaazatrinaphthylene (HATN) moiety through Sonogashira–Hagihara coupling reaction. HATN moiety can undergo a proton-induced electron transfer redox reaction, which endows HPOP-1 with high pseudocapacitive activity. As electrode materials for supercapacitor application, HPOP-1 exhibits high specific capacitance (667 F g⁻¹ at 0.5 A g⁻¹) and long-term cyclic stability (90% capacitance retention after 10,000 cycles at 5 A g⁻¹) in a three-electrode system with 1 M H₂SO₄ as the electrolyte. In addition, HPOP-1 also exhibits a specific capacitance of 376 F g⁻¹ at 0.5 A g⁻¹ in 1 M KOH electrolyte. An asymmetric supercapacitor was further fabricated with HPOP-1 as negative electrode and rGO as positive electrode, respectively. The device delivers a specific capacitance of 63 F g⁻¹ at 0.5 A g⁻¹ and a rate performance of 37 F g⁻¹ at 5 A g⁻¹. Our work provides a facile approach for the design and preparation of pseudocapacitive POPs with high specific capacitance and long cycle life.     

Synthesis of Co3O4/CoOOH via electrochemical dispersion using a pulse alternating current method for lithium-ion batteries and supercapacitors

We report a convenient, low-cost and ecofriendly approach for the fabrication of a Co₃O₄/CoOOH electrode material intended for lithium ion batteries (LIBs) and supercapacitors (SCs) using the electrochemical dispersion of the cobalt foil through the pulse alternating current (PAC) method. The synthesized material is a Co₃O₄/CoOOH composite (with about 10–15 wt% CoOOH) in the form of nanosheets with a length of approximately 200 nm and a thickness of 10–20 nm. It is found to exhibit high reversible discharge specific capacities and good cycling behavior while tested as the anode material in LIBs. Measuring the reversible capacitance at high (2C) and low (C/20) cycling rates gives the values of 610 mAh g⁻¹ and 1030 mAh g⁻¹, respectively. The specimen possesses excellent performance as the electrode for SCs with the retention of capacitance up to 98% at the current density increasing from 0.5 to 10 A g⁻¹. After 1000 cycles at a current density of 10 A g⁻¹ the electrode maintains about 90% of its initial capacitance which evidences the long cycle life. Hence, electrochemically prepared Co₃O₄/CoOOH seems to be a promising candidate for high-performance LIBs and SCs applications.     

Hierarchical FeCo2S4@FeNi2S4 Core/Shell Nanostructures on Ni Foam for High-Performance Supercapacitors

The design of electrode materials with rational core/shell structures is promising for improving the electrochemical properties of supercapacitors. Hence, hierarchical FeCo₂S₄@FeNi₂S₄ core/shell nanostructures on Ni foam were fabricated by a simple hydrothermal method. Owing to their structure and synergistic effect, they deliver an excellent specific capacitance of 2393 F g⁻¹ at 1 A g⁻¹ and long cycle lifespan as positive electrode materials. An asymmetric supercapacitor device with FeCo₂S₄@FeNi₂S₄ as positive electrode and graphene as negative electrode exhibited a specific capacitance of 133.2 F g⁻¹ at 1 A g⁻¹ and a high energy density of 47.37 W h kg⁻¹ at a power density of 800 W kg⁻¹. Moreover, the device showed remarkable cycling stability with 87.0 % specific-capacitance retention after 5000 cycles at 2 A g⁻¹. These results demonstrate that the hierarchical FeCo₂S₄@FeNi₂S₄ core/shell structures have great potential in the field of electrochemical energy storage.     

Application of a novel redox-active electrolyte in MnO2-based supercapacitors

This paper reports a novel strategy for preparing redox-active electrolyte through introducing a redox-mediator(p-phenylenediamine,PPD) into KOH electrolyte for the application of ball-milled MnO 2-based supercapacitors.The morphology and compositions of ball-milled MnO 2 were characterized using scanning electron microscopy(SEM) and X-ray diffraction(XRD).The electrochemical properties of the supercapacitor were evaluated by cyclic voltammetry(CV),galvanostatic charge-discharge(GCD),and electrochemical impedance spectroscopy(EIS) techniques.The introduction of p-phenylenediamine significantly improves the performance of the supercapacitor.The electrode specific capacitance of the supercapacitor is 325.24 F g-1,increased by 6.25 folds compared with that of the unmodified system(44.87 F g-1) at the same current density,and the energy density has nearly a 10-fold increase,reaching 10.12 Wh Kg-1.In addition,the supercapacitor exhibits good cycle-life stability.     

Electrodeposition of MnO2 nanowires on carbon nanotube paper as free-standing,flexible electrode for supercapacitors

MnO₂ nanowires were electrodeposited onto carbon nanotube (CNT) paper by a cyclic voltammetric technique. The as-prepared MnO₂ nanowire/CNT composite paper (MNCCP) can be used as a flexible electrode for electrochemical supercapacitors. Electrochemical measurements showed that the MNCCP electrode displayed specific capacitances as high as 167.5 F g⁻¹ at a current density of 77 mA g⁻¹. After 3000 cycles, the composite paper can retain more than 88% of initial capacitance, showing good cyclability. The CNT paper in the composite acted as a good conductive and active substrate for flexible electrodes in supercapacitors, and the nanowire structure of the MnO₂ could facilitate the contact of the electrolyte with the active materials, and thus increase the capacitance.     

Synthesis and characterization of macroporous Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C composites as cathode materials for Li-ion batteries

The macroporous Li₃V₂(PO₄)₃/C composite was synthesized by oxalic acid-assisted carbon thermal reaction, and the common Li₃V₂(PO₄)₃/C composite was also prepared for comparison. These samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical performance tests. Based on XRD and SEM results, the sample has monoclinic structure and macroporous morphology when oxalic acid is introduced. Electrochemical tests show that the macroporous Li₃V₂(PO₄)₃/C sample has a high initial discharge capacity (130 mAh g⁻¹ at 0.1 C) and a reversible discharge capacity of 124.9 mAh g⁻¹ over 20 cycles. Moreover, the discharge capacity of the sample is still 91.5 mAh g⁻¹, even at a high rate of 2 C, which is better than that of the sample with common morphology. The improvement in electrochemical performance should be attributed to its improved lithium ion diffusion coefficient for the macroporous morphology, which was verfied by cyclic voltammetry and electrochemical impedance spectroscopy.     

NiS Hollow Spheres for High‐Performance Supercapacitors and Non‐Enzymatic Glucose Sensors

α‐NiS and β‐NiS hollow spheres were successfully synthesized via the Kirkendall effect under different hydrothermal conditions. The obtained α‐NiS and β‐NiS hollow spheres were evaluated as electrode materials for supercapacitors. Importantly, the α‐NiS hollow sphere electrode has a large specific capacitance (562.3 F g^?1 at 0.60 A g^?1) and good cycling property (maintaining about 97.5 % at 2.4 A g^?1 after 1000 cycles). Furthermore, the as‐prepared α‐NiS and β‐NiS hollow spheres were successfully applied to construct electrochemical glucose sensors. Especially, the α‐NiS hollow spheres exhibit a good sensitivity (155 μA mM^?1 cm^?2), low detection limit (0.125 μM ), and a wide linear range.