三元脂肪酸/膨胀石墨复合相变材料的制备、包覆定形及热性能

采用癸酸、 月桂酸和棕榈酸的三元共晶混合物作为相变材料, 以膨胀石墨为基体, 通过膨胀石墨多孔结构的毛细吸附和复合涂饰剂的包覆定形, 将多元相变材料固定在膨胀石墨的孔道结构中, 制备出结构稳定、 密封性能优异、 热稳定性好和高导热的新型三元脂肪酸/膨胀石墨复合定形相变材料. 膨胀石墨具有膨胀疏松的多孔结构和良好的吸附性能; 其熔融潜热为95.6 J/g, 结晶焓为82.8 J/g, 说明其具有很好的相变蓄热特性和热循环稳定性; 材料的导热性能可增加至0.738 W/(m·K), 与脂肪酸相比得到大幅度提高.     

Determination of Sb, Ni and V in slurry from airborne particulate material collected on filter by graphite furnace atomic absorption spectrometry

A microdigestion procedure performed directly in the autosampler cup is proposed. Small quartz filter pieces loaded with the particulate material are transferred to the cup. The sample is digested by a mixture of nitric, sulfuric and hydrofluoric acid (1:1:1) under sonication. After the addition of a boric acid solution the elements are determined by graphite furnace atomic absorption spectrometry using the autosampler to deliver the slurry into the furnace. A mixture of palladium and magnesium nitrates was used as a modifier for Sb. Spiking studies showed recoveries close to 100% using aqueous analytical curves for Ni and Sb. For V, an analytical curve in the blank slurry, obtained by submitting an unloaded filter to the same procedure, was used. The method was applied to two standard reference materials, Coal Fly Ash (NIST 1633a) and Urban Particulate (NIST 1648) and the concentrations showed good agreement with the certified or recommended values using aqueous analytical solutions.     

Direct determination of boron and zirconium in ceramic materials by flame atomic absorption spectrometry after alkali sintering and fusion

Both boron and zirconium are present in ceramic materials as major silica components and have to be determined for quality control in the ceramic industry. For boron determination, sintering with a mixture of Na2CO3 and ZnO is proposed for decomposition of samples. For zirconium determination, acid digestion using an HF-HClO4 mixture and subsequent fusion with NaKCO3 and H3BO3 is proposed as decomposition step. The AAS absorbance signal of these elements is suppressed by the fusion elements in the samples. Therefore, the calibration solutions for both B and Zr must contain an appropriate concentration of sodium, sodium-potassium, and boron salts. An AIF3 solution was used for signal enhancement and improving the linearity of the Zr calibration curve. The methods proposed are well suited for the determination of higher concentrations of both boron and zirconium in silicate samples.     

Study of reaction processes by in-line near-infrared spectroscopy in combination with multivariate curve resolution: Esterification of myristic acid with isopropanol

The acid-catalysed esterification of myristic acid with isopropanol was studied by using near-infrared spectroscopy (NIR) in combination with soft-modeling curve resolution (MCR) methodology with a view to establishing the effect of experimental variables on the reaction kinetics. The reaction was conducted at temperatures above the boiling point of the alcohol, with continuous addition of an isopropanol/water mixture to the reactor. Spectral and concentration profiles were determined by applying soft-modeling curve resolution methodology to a column-wise augmented data matrix containing the spectra for the pure components. MCR profiles were compared with reference values and found to depart from then by less than 3% as %RSE for concentrations and to exhibit correlation above 0.999 for spectra.The reaction kinetics as estimated from the concentration profiles was found to be pseudo-first-order. Also, the pseudo-first-order rate constant was found to depend on the flow-rate of the isopropanol/water mixture and its water content; although the constant decreased with increase in the proportion of water, a content of ca. 15% could be used without important retarding effects on the kinetics. The proposed NIR-MCR method allows the rate constant and the influence of the initial water content to be determined with a view to minimizing consumption of the raw materials and optimizing the experimental conditions.     

纳米晶型MnCo2O4的微波加热法制备及其电催化性能

以Co和Mn的醋酸盐为原料,采用共沉淀法制得草酸盐前驱物,加入一定量微波吸波剂乙炔黑后,用微波进行热处理制得复合氧化物MnCo2O4.X射线衍射和扫描电镜结果表明,产物为纳米晶型,结晶良好,纯度较高,粒径为10~20nm且分布均匀.在室温下、空气气氛中,以6mol/L的KOH溶液为电解液测试了由MnCo2O4制备的空气扩散电极对氧还原反应的催化效果.极化曲线显示,在-0.2V(vsHg/HgO)电位下,氧还原反应电流密度达96mA/cm2.为显示微波加热法的优越性,用马弗炉煅烧制备了MnCo2O4,并对两种热处理方法所得产物的物化性能进行了比较.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Electrothermal vaporization system using furnace-fusion technique for the determination of lead in botanical samples by inductively coupled plasma atomic emission spectrometry

A new approach to sample digestion, subsequent vaporization and introduction into an inductively coupled plasma atomic emission spectrometer was developed for the direct determination of lead. To each small sample cuvette made of tungsten, a mixture of a ground solid sample and powdered diammonium hydrogenphosphate was precisely weighed. The cuvette was positioned onto the tungsten boat furnace (TBF) incorporating a vaporizer. Tetramethylammonium hydroxide solution was added. Then the cuvette was heated and maintained at a wet-digestion temperature to decompose the solid sample. After digestion, the temperature was elevated to generate the analyte vapor for introduction into a plasma. Since the solid samples were wet-digested in the sample cuvettes before vaporization, they could be analyzed by using a calibration curve prepared from aqueous standard solutions. This method was applied to the determination of lead in several biological materials with satisfactory results.     

Calorimetry and other methods in the studies of expansive cement hydrating mixtures

In this study, the calorimeter was applied to follow the hydration of special cement mixtures exhibiting expansion or shrinkage compensation. The shrinkage-less and expansive binders were produced by mixing of Portland cement with an expansive additive produced by sintering and composed of calcium sulfoaluminate (yeelimite), calcium sulfate (anhydrite) and lime. The studies were focused on the synthesis of this aluminate??sulfate??lime additive (temperature of burning process as a parameter controlling the relative activity of components) from the materials being the by products and subsequently on the mixture proportions to ensure the hydration process resulting in non-shrinkage or expansion effect. In the experiments the proportions of expansive mixture and cementitious materials were variable. The investigations with aim to find the relationship between the volume changes and composition of initial mixtures in cement pastes and mortars (with sand) were also carried out. The phase composition and microstructure of products were characterized. The expansive additive in the environment of hydrating cement transforms into ettringite and gives an increase of volume when the plastic material transforms to the more rigid matter but before the ultimate hardening takes place. Proper, moderate setting and hardening in strongly modified mixtures is achieved when the calorimetric curve corresponding to the heat evolution on hydration is analogous to that for the basic Portland cement. The rate of heat evolution data are well compatible with the other results related to the other methods of hydration kinetics assessment (e.g. chemical shrinkage) and discussed in terms of the phase composition of hydration products.     

Distinctive features of radiothermoluminescence curves of alkanes

Radiothermoluminescence (RTL) curves of alkanes have a special character: each curve is specific to a particular alkane and thus can be used for identifying it. The RTL curve of a mechanical mixture of two alkanes quantitatively coincides with the sum of the curves for the individual components of the mixture. The additivity property is lost for the mixtures prepared from a melt or chloroform solution. The loss is due to the change of the crystalline state of the mixture. An X-ray study shows that the X-ray diffractogram of such a mixture does not coincide with the sum of diffractograms of the individual components (even the crystal lattice type changes).     

Evaluating the logistic mixture model on real and simulated TG curves

The aim of this paper is to evaluate and explain the fitting of dynamic TG curves by a mixture of logistic functions. This model assumes that more than one physical process may be involved in each mass loss step and that each physical process may extend along all the experiment. One of the main sources of difficulties in TG is that, very often, different stages of decomposition substantially overlap each other. Several real and simulated TG curves were analysed in this paper. An optimal fitting of the TG curves was obtained by a mixture of logistics. In many cases the optimal fitting reproduces accurately the TG curve. Accordingly, the TG curve can be understood as a sum of parallel reactions, where each single reaction is represented by one or a small number of logistic components. Additionally, making use of the analytical derivative of the fitting, a mixture of Arrhenius reaction order equations was applied to the same curves. In all the cases, the fitting obtained with the mixture of Arrhenius was worse than the obtained with the mixture of logistics. A software was developed to automatically perform these tasks. The physical meaning of the fitting was explained.     

APTox: 化学混合物毒性评估与预测

真实环境中化学混合物的存在是普遍规律. 化学混合物联合效应具有与单个组分不同的变化规律, 目前缺少有效方法学与可靠基础数据. 近年来, 我们试图探索建立化学混合物毒性评估与预测(APTox)的方法体系. 发展了微板毒性分析法(MTA)以提高测试数据精密度, 创建了直接均分射线(EquRay)与均匀设计射线(UD-Ray)法来有效表征混合物浓度组成, 建立了支持向量回归(SVR)技术拟合不同形状浓度-效应曲线, 提出了将实验混合物整体剂量-效应曲线(CRC)与加和参考模型预测CRC比较以评价混合物毒性相互作用的方法, 集成多种技术设计开发了化学混合物毒性评估与预测的应用程序.     

Molecular simulations of Hugoniots of detonation product mixtures at chemical equilibrium: microscopic calculation of the Chapman-Jouguet state

In this work, we used simultaneously the reaction ensemble Monte Carlo (ReMC) method and the adaptive Erpenbeck equation of state (AE-EOS) method to directly calculate the thermodynamic and chemical equilibria of mixtures of detonation products on the Hugoniot curve. The ReMC method [W. R. Smith and B. Triska, J. Chem. Phys. 100, 3019 (1994)] allows us to reach the chemical equilibrium of a reacting mixture, and the AE-EOS method [J. J. Erpenbeck, Phys. Rev. A 46, 6406 (1992)] constrains the system to satisfy the Hugoniot relation. Once the Hugoniot curve of the detonation product mixture is established, the Chapman-Jouguet (CJ) state of the explosive can be determined. A NPT simulation at P(CJ) and T(CJ) is then performed in order to calculate direct thermodynamic properties and the following derivative properties of the system using a fluctuation method: calorific capacities, sound velocity, and Gruneisen coefficient. As the chemical composition fluctuates, and the number of particles is not necessarily constant in this ensemble, a fluctuation formula has been developed to take into account the fluctuations of mole number and composition. This type of calculation has been applied to several usual energetic materials: nitromethane, tetranitromethane, hexanitroethane, PETN, and RDX.     

Testing predictions of macroscopic binary diffusion coefficients using lattice models with site heterogeneity

Quantitatively predicting mass transport rates for chemical mixtures in porous materials is important in applications of materials such as adsorbents, membranes, and catalysts. Because directly assessing mixture transport experimentally is challenging, theoretical models that can predict mixture diffusion coefficients using only single-component information would have many uses. One such model was proposed by Skoulidas, Sholl, and Krishna (Langmuir, 2003, 19, 7977), and applications of this model to a variety of chemical mixtures in nanoporous materials have yielded promising results. In this paper, the accuracy of this model for predicting mixture diffusion coefficients in materials that exhibit a heterogeneous distribution of local binding energies is examined. To examine this issue, single-component and binary mixture diffusion coefficients are computed using kinetic Monte Carlo for a two-dimensional lattice model over a wide range of lattice occupancies and compositions. The approach suggested by Skoulidas, Sholl, and Krishna is found to be accurate in situations where the spatial distribution of binding site energies is relatively homogeneous, but is considerably less accurate for strongly heterogeneous energy distributions.     

Development of low cost pulmonary surfactants composed of a mixture of lipids or lipids-peptides using higher aliphatic alcohol or soy lecithin

The artificial pulmonary surfactant composition in the present study is characterized by a lipid mixture system composed of higher aliphatic alcohol, egg yolk phosphatidylcholine (egg PC), soy lecithin and higher aliphatic acid as the major components or a peptide-lipid mixture system composed of a combination of the lipid mixture system to which a peptide is added. Three peptides with amphiphilic surface-staying, membrane spanning, and both properties were designed and synthesized. The evaluation of pulmonary surfactant assay was performed by a hysteresis curve drawn upon the measurement for the surface tension-area curve with the Wilhelmy surface tensometer in vitro and the recovery of lung compliance for the pulmonary surfactant-deficient rat models in vivo. Lipid-mixture systems composed of octadecanol or soy lecithins containing no peptide were favorable hysteresis curves as compared with commercially available Surfacten((R)), but were not prominent. The peptide-lipid mixture systems composed of a combination of the lipid mixture of alkyl alcohol or soy lecithin to which peptides designed were added were desirable hysteresis curves similar to Surfacten((R)) and amphiphilic Hel 13-5 peptide-lipids mixture systems were much more effective than the lipid mixture system. Particularly, the recovery of lung compliance treated with hydrogenated soy lecithin-fractionated soy lecithin PC70-palmitic acid-peptide Hel 13-5 (40:40:17.5:2.5, w/w) was comparable to that with Surfacten((R)). Because the artificial pulmonary surfactant compositions of this study can be prepared at lower costs, they are useful for the treatment of respiratory distress syndrome and acute respiratory distress syndrome as well as for inflammatory pulmonary diseases, dyspnea caused by asthma, etc.     

Production of Cordycepin and Mycelia by Submerged Fermentation of Cordyceps militaris in Mixture Natural Culture

The submerged fermentation of Cordyceps militaris for cordycepin production and mycelial growth was investigated in this study. Three natural materials of brown rice paste (BRP), beerwort (B), and soybean meal juice (SMJ) were used for fermentation of C. militaris in shaking flasks. The effects of the ratio of three natural materials on dry mycelium weight (DMW) and on cordycepin yield (CY) were analyzed. D-Optional mixture design was used to optimize the ratio of these materials. Compared with the signal culture, the higher mycelial growth and cordycepin production were obtained in mixture. The analysis of Design Expert 6.0 indicated that BRP, B, and SMJ very significantly influenced (P < 0.001) DMW and CY of C. militaris, respectively. The highest DMW (18.96 g/l) and CY (2.17 mg/g) were both obtained at a ratio of 53:6:42. The experiments’ results indicated that the above mixture of these natural materials by D-optional mixture design can be used as a proper medium for the growth of mycelium and the production of cordycepin.     

Study of dielectric constants of binary composites at microwave frequency by mixture laws derived from three basic particle shapes

Powder mixture rules derived from the filler particles with the shapes of sphere, cylinder or rod, and lamella or disk with random distributions are studied in this paper. Three ceramic powders of fillers with dielectric constants of 10, 20, and 36, respectively, are adopted. The experimental dielectric constants of ceramic dispersions in the polyethylene matrix at microwave frequency are compared to those obtained by using different mixing laws. The mixing rules are also adopted to estimate the dielectric constants of pure ceramics from the measured dielectric constants of composites with various concentrations. The theory for the error of estimation is studied. In contrast to the traditional concept of obtaining the best curve fitting of mixture rule with the experimental data, this study conclude a very important concept on the powder mixture rule, that is, the most adequate mixture law for estimating the dielectric constants of pure ceramics requires both good curve fitting and potential of less error.     

Fluorimetric and high-performance liquid chromatographic determination of D-lactate in biological samples

D-Lactate in biological samples was converted into a strongly fluorescent substance in a one-vial reaction. It was first converted into the pyruvate hydrazone in the presence of D-lactate dehydrogenase, an NADH-reoxidation system using diaphorase, D,L-6,8-thioctamide and hydrazine. This hydrazone was then converted into 2-hydroxy-6,7-dimethoxy-3-methylquinoxaline by 1,2-diamino-4,5-dimethoxybenzene in 1 M hydrochloric acid, and the quinoxaline was extracted and measured fluorimetrically at 432 nm (excitation at 365 nm). The calibration curve for D-lactate was linear up to at least 100 nmol/ml of the assay mixture, with a determination limit of 2 nmol/ml. The quinoxaline was also analysed by high-performance liquid chromatography with fluorimetric detection. The calibration curve for D-lactate was linear from 500 fmol to 75 nmol in the reaction mixture. This method was 4000 times more sensitive than the fluorimetric method, and could determine D-lactate in blood plasma volumes of less than 1 microliter.     

Application of Vegard's law to mixed cation sodalites: a simple method for determining the stoichiometry

Vegard’s law describes the empirical relationship between the crystal lattice parameter of a mixture and its components. This relationship holds for some sodalites, in particular those containing mixtures of Li, K and Na as the charge balancing cations. By utilizing previously published lattice parameters for Li/Na and K/Na mixed cation chloride sodalites, linear curves were drawn allowing the composition of the mixed cation sodalites to be determined from their lattice parameters. Further, by mathematical addition of the curves for Li/Na and K/Na mixed cation chloride sodalites, a linear curve was developed and tested for the mixed tri-cation Li/Na/K chloride sodalites. This provides a simple way to monitor the composition of mixed cation sodalites and has an application in monitoring the composition of multi-phase materials where the sodalite phase cannot be easily separated for elemental analysis.     

Comparison of the acid combinations in microwave-assisted digestion of marine sediments for heavy metal analyses.

Sediments as a tool for monitoring contamination by heavy metals in the environment has long been considered. It is therefore a necessity to produce reliable data for such purposes. Microwave-assisted acid dissolution has proved to be a suitable method for digesting complex matrices, such as sediments. However, due to the infancy of the technique, the procedures are numerous and varied in both the reagents used and microwave conditions. In this study, the efficiency of two recommended acid mixtures, a HNO3-HF mixture and an aqua regia-HF mixture, under the same microwave digestion conditions were compared using certified reference materials. It was observed that the HNO3-HF mixture showed better efficiency than the aqua regia-HF mixture in most of the heavy metals analyzed in all certified reference materials used.     

Quantitative analysis of elements (C, N, O, Al, Si and Fe) in polyamide with wavelength dispersive X-ray fluorescence spectrometry

A wavelength dispersive X-ray fluorescence (WD-XRF) spectrometry combined with calibration curve method was established for simultaneously analyzing low-Z elements (C,N,O) and Al,Si,Fe in polyamide.To investigate the origin of plastic material causing deposition and blocking in instrument engines and pipelines,polyamide 6 (PA 6,an engineering plastic) was chosen as the study object on account of its common use in industry.The sample preparation with pressed powder disk has been developed for determination of six elements in PA 6.Pure Cu metal was used as the matrix and PA 6 was regarded as standard sample for C,N,O elements.PA 6 particles were firstly smashed to uniform powder in liquid nitrogen,and then mixed with inorganic standard powders (Fe2O3,Al2O3,SiO2,and Na 2 SiO 3).The mixture was ground to obtain homogeneous calibration materials for WD-XRF analysis.The quantitative property of the calibration curve method for each element was reliable.The limits of detection (S/N≤3) of C,N,O,Al,Si and Fe using WD-XRF were 249,120,101,6.2,3.3,and 1.8 μg/g,respectively.To confirm the accuracy of the proposed WD-XRF calibration curve method,inductively coupled plasma optical emission spectroscopy (ICP-OES) detection for Al,Si,Fe and elemental analyzer (EA) analysis for C,N,O were utilized.A good correlation of the WD-XRF results with the measurements of ICP-OES and EA was observed.