Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

Nuclear interferences of uranium and thorium in a reactor neutron activation analysis determination of cerium using the radionuclides141Ce and143Ce

The interference contributions of uranium and thorium to the determination of cerium based on radionuclides¹⁴¹Ce and¹⁴³Ce produced by irradiation in a reactor core was determined. The values of the interference contributions for¹⁴¹Ce were 0.28±0.01 g Ce/g U and /2.01±0.05/x10^–3 g Ce/g Th, and for¹⁴³Ce 1.33±0.03 g Ce/g U and /9.0±0.2/x10^–3 g Ce/g Th.     

Path of “dry” electrons before localization in liquid hydrocarbons

Conclusions On the basis of measurements of values of in liquid hydrocarbons, it has been shown that the path length before localization of a photoliberated electron increases with increasing mobility of the excess electron, from approximately 40 Å (methylcyclohexane) to 200 Å (isooctane). In a liquid with10^–2 cm²/V·sec (methylcyclohexane, hexane), the localization takes place before or immediately after thermalization of the electron. In a liquid with>10^–1 cm²/V·sec, the electron passes through the main part of its path before localization, being in thermal equilibrium with the medium.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 10, pp. 2198–2203, October, 1985.     

Binuclear Osmium μ-Oxocarboxylate Complexes [Os2(μ-O)(μ-O2CR)2Cl4L2] (R = CH3, CCl3; L = PPh3, AsPh3) and Their Electrochemical Behavior in Dichloromethane

Cyclic voltammetry and galvanostatic coulometry techniques were used to determine how the redox properties of osmium binuclear -oxocarboxylates [Os₂ ^IV(-O)(-O₂CR)₂Cl₄L₂] (R = CH₃, CCl₃; L = PPh₃ and R = CH₃; L = AsPh₃) are influenced by the nature of the bridging carboxylate ligand RCOO^– and ligand L. It was shown that all compounds in solution of dichloromethane undergo two single-electron reduction processes. The data obtained were compared with the DFT calculations of the electronic structure of the model complexes [Os₂ ^IV(-O)(-O₂CR)₂Cl₄L₂] (R = CH₃, CCl₃; L = PH₃ and R = CH₃; L = AsH₃).     

Amplification method for the spectrophotometric determination of phosphorus

An amplification method with ion-exchange pre-separation for the spectrophotometric phosphorus determination in various alloys is described. Phosphorus is converted into molybdophosphoric acid, separated by selective extraction and back-extracted into the aqueous phase. The molybdenum is liberated by alkaline decomposition of the heteropoly acid. The spectrophotometric measurement is based on the reaction of molybdenum(VI) with 2,2-biquinoxalyl. High molar absorptivity of 1,1-dihydro-2,2-biquinoxalylene (=3.3 · 10⁴ L mol^–1 cm^–1) and the twelve-fold amplification guarantee high precision and makes the determination of phosphorus in the 1–6 g level possible.     

Determination of pentachlorophenol residues in wine and corks by solvent extraction methodology and specific gas chromatography detection

Summary A gas chromatographic methodology with selective detection is presented for the analysis in wines and corks of pentachlorophenol residues, which are suspected to be the most likely precursors of some off-flavours described in several wine samples. After derivatisation, pentachlorophenol acetate residues were monitored by electrolytic conductivity detection and/or mass spectrometric detection in the selective ion mode at m/z 264 and 266. Recoveries varied from 80 to 96% for wine samples fortified with 5 to 100 g l^–1 and from 83 to 91% for corks (fortified at 25 to 100 g kg^–1). The proposed methodology allowed for a determination limit of g l^–1 for wine and 10 g kg^–1 for corks.     

Determination of traces of sodium alkylbenzenesulphonate by high-performance liquid chromatography. Application to water

Summary For the trace determination of sodium alkylbenzenesulphonate (ABS) by HPLC the following conditions were employed: Shimadzu ZORBAX SIL Column (5 m, 4.6 mm i.d. x 150 mm) as stationary phase, 0.2% ammoniaethanol (v/v) as mobile phase, UV detector at 225 nm, injection volume 12 l. The chromatograms of ABS were simple and sharp (detection limit of ABS 0.02 g in 12 l of ethanol). The calibration curves of ABS were linear in a concentration range of 0.03 0.3 g in 12 l of ethanol. In the case of linear sodium dodecylbenzenesulphonate positive errors of 1 4% were caused by non-ionic surfactants or laurylsulphate (6 times excess), 10 50% positive errors were caused by 2 6 times excess of household detergents.Standard water samples containing ABS were treated with a weak base anion-exchange resin, the adsorbed ABS were eluted, and then determined either by HPLC or by the methylene blue spectrophotometric method. Recoveries of ABS in water were about 92 107% by HPLC.

---

Bestimmung von Spuren Natriumalkylbenzolsulfonat mit Hilfe der HPLC. Anwendung auf Wasser

Zusammenfassung Für die Spurenbestimmung von Natriumalkylbenzolsulfonat (ABS) durch HPLC werden die folgenden Bedingungen empfohlen:Shimadzu ZORBAX SIL (5 m, 4,6 mm x 150 mm) als stationäre Phase, 0,2% Ammoniak/Ethanol als mobile Phase, UV-Detektor bei 225 nm, Injektionsvolumen 12 l. Die erhaltenen Chromatogramme sind einfach und scharf (Nachweisgrenze 0,02 g in 12 ml Ethanol). Die Eichkurven sind im Konzentrationsbereich von 0,03–0,3 g in 12 l Ethanol linear. Im Falle des linearen Natriumdodecylbenzolsulfonats werden bei Anwesenheit von nicht-ionischen oberflächenaktiven Substanzen oder von Laurylsulfat in 6fachem Überschuß positiver Fehler von 1–4% erhalten; bei 2–6fachem Überschuß von Haushaltswaschmitteln ergeben sich positive Fehler von 10–50%.Standard-Wasserproben werden zunächst einer Behandlung mit einem Anionenaustauscher unterzogen, die adsorbierten ABS eluiert und durch HPLC oder nach der Methylenblaumethode analysiert. Wiederfindungsraten liegen bei 92–107%.

     

Differential pulse voltammetric methods for the simultaneous estimation of uranium-iron and uranium-cadmium mixtures in solution

Differential pulse voltammetric methods have been developed for the simultaneous estimation of the constituents of uranium-iron and uranium-cadmium mixtures in solution. A mixture of 1M H₃PO₄–1M KH₂PO₄ (with a pH1.5), was found to be the most ideal supporting electrolyte for both methods, among many that were evaluated for their suitability. In uranium-iron mixtures the calibration for iron was found to be linear up to 150 g ml^–1 (r²=0.9986), while that of uranium up to 500 g ml^–1 (r²=0.999). Iron at 6.7 g ml^–1 level could be determined in the presence of 800 fold uranium (wt/wt) without significant interference. Uranium at 21 g ml^–1 level could be analyzed with 5-fold iron (wt/wt). This upper limit of iron was due to the precipitation of iron as phosphate. In the case of uranium — cadmium mixtures, cadmium calibration for cadmium was found to be linear up to 1300 g ml^–1 (r²=0.9993). Concentration levels of 4.6 g ml^–1 Cd could be determined at a 500-fold excess (wt/wt) of uranium. Uranium calibration was linear up to 500 g ml^–1 (r²=0.999) and 21 g ml^–1 uranium could tolerate up to a 1000-fold excess of cadmium (wt/wt). Both procedures could tolerate 10 g ml^–1 levels of metal ions, such as chromium, copper, manganese, molybdenum and vanadium.     

Determination of urinary bromine by pixe

The method of thin film PIXE was applied to the analysis of a total of 117 urine specimens from urinary stone sufferers and controls. The overall range of Br levels was between 2 and 18 g cm^–3. Mean values obtained over a period of three days ranged from 6.8 to 9.2 g cm^–3. No significant differences between the Br distributions in the two groups over the collection period were observed.     

Syntheses and structures of chalcogen–molybdenum clusters; [Mo3XSe6{S2P(OEt)2}3]Cl, [Mo3X(SeS)3{S2P(OEt)2}3]I and [Mo3 XSe3{S2P(OEt)2}4(py)] (X=0.65S+0.35Se,py= C5H5N)

The trinuclear Mo cluster [Mo3(3–X)(2–Se2)3{S2P-(OEt)2}3]Cl (X=0.65S+0.35Se) (1) has been synthesised by reacting MoCl3·3H2O with ZnSe and [Me4N][S2P(OEt)2] in an EtOH/HCl medium. Reduction of (1) by Ph3P in the presence of [Me4N]-[S2P(OEt)2] and pyridine gave [Mo3(3–X)(2–Se)3 {S2P(OEt)2}4(py)] (X=0.65S+0.35Se, py=C5H5N) (2). Complex (2) was, in turn, converted into [Mo3(3–X)(2–SeS)3{S2P(OEt)2}3]I (X=0.65S+0.35Se) (3) by treatment with H2S and I2. The structures of complexes (1), (2) and (3) were established by X-ray crystallography.     

New cobalt trimethylacetate complexes with pyridine

The reaction of the tetranuclear trimethylacetate complex Co₄(₃-OH)₂(-OOCCMe₃)₄(²-OOCCMe₃)₂(EtOH)₆ with pyridine in acetonitrile was studied. Two new compounds, viz., the hexanuclear cobalt(ii) complex Co₆py₄(₃-OH)₂(-OOCCMe₃)₁₀ (25% yield) and the unusual ionic compound [Co₃py₃(₃-O)(-OOCCMe₃)₆]⁺[Co₄py(₄-O)(-OOCCMe₃)₇]^– (5% yield), were prepared. The structures of the new compounds were established by X-ray diffraction analysis.     

Photometric determination of molybdenum in iron and steels using tin(II) chloride in nonaqueous solvent

Summary A new procedure is proposed for the photometric determination of molybdenum in iron and steels using thiocyanate and tin(II) chloride solution [in glycerol-ethannol (31) or in diethylenglycol] as a reducer and extraction with n-butyl acetate. Beer's law is obeyed between 0.2 and 80 g Mo/ml. The minimum photometric error is 3.2%, the molar absorptivity is 15640 at 470 nm and the best concentration range for determination is between 0.6 and 6 g Mo/ml.

---

Photometrische Bestimmung von Molybdän in Eisen und Stahl mit Hilfe von Zinn(II)-chlorid in nichtwärigem Medium

Zusammenfassung Das vorgeschlagene Verfahren beruht auf Bildung des Thiocyanatkomplexes unter Verwendung von Zinn(II)-chlorid als Reduktionsmittel [in Glycerin/Äthanol (31) oder Diäthylenglykol]. Als Extraktionsmittel dient n-Butylacetat. Das Beersche Gesetz wird im Bereich 0,2–80 g Mo/l befolgt. Der kleinste photometrische Fehler beträgt 3,2%, die molare Extinktion 15640 bei 470 nm und der optimale Konzentrationsbereich 0,6–6 gMo/l.

Lecture presented at Euroanalysis I Conference, 28. 8. –1. 9. 1972 in Heidelberg, Germany.     

Determination of oxygen by deuteron-induced PIPPS

Using the 871-keV¹⁶O p/1,0/ prompt -ray, oxygen was determined with a relative precision of ±3.8% at a concentration level of 120 g g^–1. The sensitivity of the method is below 10 g g^–1. 50 nm oxide layers on silicon wafers can be determined with a relative precision of 10%. A chamber for transporting targets sensitive to atmospheric gases and humidity is described.     

ET-AAS in the Analysis of high-purity mercury

ET-AAS is investigated for the analysis of high purity mercury. Two possibilities are proposed: ET-AAS determination of trace analytes in the presence of high mercury concentrations or after matrix separation by reduction. The ET-AAS analysis of high-purity mercury under optimal instrumental parameters permits fast and reproducible determination of 0.03 gg^–1 Al, Cd and Mn; 0.05 gg^–1 Cu, Co, Cr, Fe, Ni and Pb and 0.2 gg^–1 V. Preliminary mercury matrix reductive separation with ascorbic acid allows determination of 0.005 gg^–1 Cd, 0.02 gg^–1 Cu, Cr and Mn, 0.03 g g^–1 Co, Ni and Pb, 0.05 g g^–1 Al and Fe and 0.1 gg^–1 V, but the reproducibility is lower. The main advantage of the second procedure is that it avoids laboratory and instrument pollution with toxic mercury.     

Chemical behaviour of helium muonide just after muon catalyzed fusion

Chemical behaviour of a helium muonide atom /He^o/ can be understood on the analogy of its hydrogen homologues, muonium /Mu/, deuterium /D^o/ and tritium /T^o/. In muon catalyzed fusion /CF/, a small fraction of negative muon in the fusion cycle sticks to helium to give proton-like He⁺ which easily picks up one electron forming He^o. The energy of He⁺ at birth is about 3.5 MeV being in a similar situation to the case of a hot tritium atom produced by /n, p/ or /n, / reaction. The reaction cross section and rate of He^o reactions are estimated.     

A new spot test reagent for chromium(VI), vanadium(V), and hexacyanoferrate(III) ions: the schiff base from 4,4′-methylenedianiline and 4-dimethylaminobenzaldehyde

Summary A new Schiff base, bis(4-dimethylaminobenzylidine)4,4-methylenedianiline (I) has been prepared by reacting 4-dimethylaminoben-zaldehyde with 4,4-methylenedianiline. A 1% solution ofI in conc. sulphuric acid gives a deep red or blood red colour with Cr(VI), and V(V), and a deep rose red colour with [Fe(CN)₆]^3-. The limits of detection and dilution are 0.7 g, 171,000 for Cr(VI); 5 g, 110,000 for V(V); and 7 g, 17,100 for [Fe(CN)₆]^3-. Cr(III), V(IV), and [Fe(CN)₆]^4- do not interfere. The effects of common anions and cations are reported.

---

Zusammenfassung Durch Umsetzung von 4-Dimethylaminobenzaldehyd mit 4,4-Methylen-dianilin wurde eine neue Schiffsche Base hergestellt, deren 1%ige Lösung in konz. Schwefelsäure eine tiefrote oder blutrote Farbe mit Cr(VI) und V(V), eine tiefrosa Farbe mit [Fe(CN)₆]^3– gibt. Die Nachweisgrenzen bzw. die Grenzkonzentrationen betragen: 0,7 g, 171000 für Cr(VI), 5 g, 110000 für V(V) und 7 g, 17100 für [Fe(CN)]₆ ^3–. Cr(III), V(IV) und [Fe(CN)₆]^4– stören nicht. Der Einfluß gängiger Anionen und Kationen wird angegeben.

     

Semi-automatic catalytic titration of some aminopoly-carboxylic acids,copper(II), and cobalt(II)

Summary A semi-automatic potentiometric method is described for the catalytic titrimetric determination ofg amounts of some aminopolycarboxylic acids. The method is based on their inhibitory effect on the copper(II)-catalyzed periodate-thiosulfate reaction. Amounts of EDTA in the 0.7–600g range (10^–6–8×10^–5 M), of DCTA in the 7–7000g range (10^–6–10^–3 M), of EGTA in the 0.8–800g range (10^–7–10^–4 M), and of DTPA in the 4–800g range (5×10^–7–10^–4 M) were determined with average relative errors and coefficient of variation of about 0.4–1%. The method has also been used for the indirect catalytic titrimetric determination ofg amounts of Cu²⁺ and Co²⁺ ions with about the before mentioned accuracy and precision.

---

Halbautomatische katalytische Titration einiger Aminopolycarbonsäuren sowie von Cu(II) und Co(II)

Zusammenfassung Eine halbautomatische potentiometrische Methode zur katalytischen Maßanalyse von Mikrogrammengen einiger Aminopolycarbonsäuren wurde angegeben. Sie beruht auf dem Hinderungseffekt gegenüber der Cu(II)katalysierten Perjodat-Thiosulfatreaktion. EDTA in Mengen von 0,7–600g, DCTA in Mengen von 7–7000g, EGTA in Mengen von 0,8–800g und DTPA in Mengen von 4–800g wurden mit einem mittleren relativen Fehler von etwa 0,4–1% bestimmt. Das Verfahren wurde auch zur Bestimmung von Cu(II) und Co(II) mit der angeführten Genauigkeit verwendet.

     

Determination of nitrate in natural waters by flow-injection analysis

Summary Nitrate was determined in natural water samples by flow-injection spectrophotometry. It was reduced to nitrite with copperized cadmium and the nitrite thus produced reacted with p-aminoacetophenone and m-phenylenediamine. The limit of detection was about 1.5 g l^–1 for sample injections of 650 l. The sampling rate was about 40 samples h^–1 and the relative standard deviation was above 1% for 0.1–0.3 mg l^–1 nitratenitrogen. Nitrite present in the sample was determined separately and subtracted.

---

Nitratbestimmung in natürlichen Wässern mit Hilfe der Fließinjektions-Analyse

Zusammenfassung Nitrat wird bei dieser Methode mit Hilfe einer Cu/Cd-Reduktionssäule zu Nitrit reduziert, das mit p-Aminoacetophenon und m-Phenylendiamin zur Reaktion gebracht wird. Die gebildete Verbindung wird spektral-photometrisch gemessen. Die Nachweisgrenze beträgt etwa 1,5 g/l bei injizierten Probevolumina von 650 l. Der Probendurchsatz beträgt 40/h. Die relative Standardabweichung liegt über 1% bei 0,1–0,3 mg/l Nitrat-Stickstoff. Vorhandenes Nitrit wird gesondert bestimmt und abgezogen.

     

Simultaneous determination of copper,mercury and lead by first-order derivative spectrophotometry using dithizone as reagent

A first-order derivative spectrophotometric method has been developed for the simultaneous determination of copper, mercury and lead at g/L levels using dithizone as reagent. The procedure involves the simultaneous extraction of these elements by dithizone in chloroform from weakly alkaline solutions. Linear calibration curves were obtained in the ranges 0.5–10 (Cu), 1–10 (Hg) and 1–10 (Pb) g present in 40 ml of aqueous phase with detection limits of 5 g/L (Cu) and 20 g/L (Hg and Pb). The R.S.D.s for 100 g/L of copper, mercury and lead were 2.5, 2.6 and 3.1% respectively, for 5 determinations. The method is applicable for the determination of copper and lead in marine sediment samples with good precision and accuracy.     

Extractive spectrophotometric determination of dioxouranium(VI) with the sodium salt of hexamethyleneiminecarbodithioate

The optimum conditions for the extractive spectrophotometric determination of dioxouranium(VI) with hexamethyleneiminecarbodithioate(HMICdt) have been established. Dioxouranium(VI) reacts with this ligand at pH 4.5 to form a yellowish-orange uncharged 12 metal-ligand complex which can be extracted by chloroform. The calibration graph was linear in the range of 1–20 g ml^–1 of dioxouranium(VI) at 335 nm. The molar absorptivity of the extracted species is 5.952×10³ l mol^–1 cm^–1 with Sandell's sensitivity of 0.04 g cm^–2. The average of 10 determinations of dioxouranium was 49.75 g for the samples containing 50 g of U(VI) and the variation from the mean at 95% confidence limit was 49.75±0.5955.