Determination of rare earth elements in human hair and wheat flour reference materials by inductively coupled plasma mass spectrometry with dry ashing and microwave digestion

A method was developed for the determination of all rare earth elements (REEs) at sub ng g⁻¹ levels in human hair (GBW 09101, SRM, Republic of China) and wheat flour (GBW 08503, SRM, Republic of China) by Inductively coupled plasma mass spectrometry (ICP-MS). The values obtained by dry ashing and microwave oven digestion procedures were compared with those obtained by traditional open vessel acid digestion method. The validity of the analytical procedure was examined by analyzing spiked samples and two vegetables (GBW 07603 and GBW 07605, SRMs, Republic of China). The results are satisfactory. The detection limits for 14 REEs ranged from 0.0039 to 0.0003 ng cm⁻³ in solution and the quantification limits ranged from 0.16 to 0.01 ng g⁻¹ in solid sample. The precision for most REEs were less than 10% RSD.     

Photographic plasma images and electron number density as well as electron temperature mappings of a plasma sustained with a modified argon microwave plasma torch (MPT) measured by spatially resolved Thomson scattering

In this work the determination of electron number densities and electron temperatures for the case of a modified microwave plasma torch (MPT) operated at 100 W with argon by means of spatially resolved Thomson scattering measurements and photographic records of the MPT at different working conditions are reported. With an internal gas flow of 500 ml min⁻¹ and an outer gas flow of 200 ml min⁻¹ electron number densities and electron temperatures are in the range of 10²⁰ m⁻³ to 10²¹ m⁻³ and of 16 000–18 000 K, respectively. When increasing the internal gas flow from 500 to 900 ml min⁻¹ the plasma becomes longer and the maximum electron number density increases by a factor of 2. An increase of the outer gas flow from 200 to 700 ml min⁻¹ leads to a lifting of the whole plasma from the burner edge with the maximum electron number density remaining unchanged. An increase of the power from 80 to 180 W was found to lead to higher electron number densities whereas the electron temperatures remain unchanged. The addition of 1.2 mg min⁻¹ of water vapor to the internal gas flow leads to a decrease of the electron number density from 4.7×10²⁰ m⁻³ to 2×10²⁰ m⁻³ and to an increase of the electron temperature from 16 000 to 22 000 K. In order to document the influence of the internal gas flow rate, water introduction and introduction of easily ionized elements on the visible plasma shape digitally recorded photos of the plasma are presented.     

Synthesis and characterization of CaBi4Ti4O15 thin films annealed by microwave and conventional furnaces

CaBi₄Ti₄O₁₅ thin films were deposited by the polymeric precursor method and crystallized in a domestic microwave oven and conventional furnace. The films obtained for microwave energy are well-adhered, homogeneous and with good specularity when treated at 700 ^°C for 10 min. The microstructure and the structure of the films can be tuned by adjusting the crystallization conditions. When microwave oven is employed, the films presented bigger grains with mean grain size around 80 nm. For comparison, films were also prepared by the conventional furnace at 700 °C for 2 h.     

Comparison of two digestion procedures for the determination of lead in lichens by electrothermal atomic absorption spectrometry

The efficiency of two procedures for the digestion of lichen was investigated using a heating block and a microwave oven. In the open vessels, concentrated nitric acid was added to the samples, left for 1 h, and the addition of 30% (v / v) hydrogen peroxide completed the digestion. In the closed system, the complete digestion was performed using concentrated nitric acid and hydrogen peroxide, reducing the amount of chemicals, time and contamination risk. Both digestion methods gave comparable results, and recoveries were statistically not different. For a lichen sample spiked with 10 μg Pb, the recovery was 111% and 110% using microwave and heating block digestion, respectively, while it was 100% and 103% for a 100 μg Pb spike. For the determination by electrothermal atomic absorption spectrometry samples were diluted 20 times with water and a volume of 20 μL was injected into the graphite furnace without chemical modifier. Pyrolysis and atomization temperatures of 700 °C and 1500 °C, respectively, were used. The characteristic mass was 8.4 ± 0.6 pg for aqueous calibration solutions and 8.9 ± 0.8 pg for samples. Calibration was against matrix matched standards. The recovery test showed some contamination problem with the lowest concentrations in both procedures. The detection limits were 4.4 μg L^− 1 with microwave oven and 5.4 μg L^− 1 with the heating block in the undiluted blank.     

Determination of mercury in organic solvents and gas condensates by μflow-injection — inductively coupled plasma mass spectrometry using a modified total consumption micronebulizer fitted with single pass spray chamber

A high-throughput flow-injection — inductively coupled plasma mass spectrometry (ICP MS) analytical method was developed for the determination of mercury in gas condensates and carbon-rich solvents. The sample (undiluted or diluted 10-fold) was introduced via a modified total consumption micronebulizer working at a flow rate of 30 μl min^− 1 and fitted with a singlepass spray chamber. This low flow rate and the addition of oxygen (70 ml min^− 1) assured the plasma stability and reduced the carbon build-up on the interface and on ion lenses. A limit of detection of 0.5 ng g^− 1 (2.5 μl sample) was obtained owing to the reduction of dead volume and sample dispersion (peak-width was 3 s at half-height) in the liquid pass of the nebulizer. The elimination of the memory effect reduced the washout time down to 30 s which resulted in a throughput of ca. 60 h^− 1. The method was validated by the analysis of 3 gas condensates by cold vapour atomic absorption spectrometry.     

Coupled chemoenzymatic transfer hydrogenation catalysis for enantioselective reduction and oxidation reactions

Stereoselective reductions of prochiral ketones were performed using a new thermophilic, NAD-dependent alcohol dehydrogenase from Thermus sp. (TADH). The enzyme was produced on 2L-scale from recombinant Escherichia coli and purified by a simple, one-step heat treatment procedure yielding 220 mg of pure enzyme. Regeneration of NADH was catalyzed by the organometallic complex [Cp*Rh(bpy)(H₂O)]²⁺ using formate as a reducing agent. The catalytic performance of [Cp*Rh(bpy)(H₂O)]²⁺ in terms of total number of catalytic cycles and number of catalytic cycles per hour achieved herein (up to 1500 and more than 400 h⁻¹, respectively), are the highest reported for a non-enzymatic nicotinamide regeneration system so far. Chemoenzymatic reduction reactions in a two liquid phase setup were performed on a gramme-scale, for example, 1.3 g of enantiopure (1S,3S)-3-methylcyclohexanol was obtained after purification. The volumetric productivity reached up to 3.9 mM h⁻¹ with an average of 2.6 mM h⁻¹ (5.3 g L⁻¹ d⁻¹) over 10 h. In addition, chemoenzymatic oxidations utilizing the same catalyst set and molecular oxygen as a terminal electron acceptor were performed. Thus, the preparative value of chemoenzymatic transfer hydrogenations with [Cp*Rh(bpy)(H₂O)]²⁺ as a regeneration catalyst coupled especially to thermophilic ADHs was demonstrated.     

A highly stable cylindrical microwave cavity resonator for the measurement of the relative permittivities of gases

We present a new and highly stable cylindrical microwave cavity resonator designed for the measurement of the relative permittivities of gases. The cylinder has an internal volume of just 5.7 cm ³, which makes it the smallest such a resonator reported to date. The equipment and procedure used to measure the resonance frequencies and halfwidths with fractional random errors better than  ±  6 · 10 ^− 7and  ±  4 · 10 ^− 3, respectively, are described. We have developed also an analytical model which describes the cylinder’s resonant behaviour with a fractional accuracy of the order of  ±  10 ^− 6. Our model includes a novel method for determining the perturbation due to the presence of an opening in the boundary wall which is shown to be in excellent agreement with experimental results.     

Partial oxidation of ethane to syngas in an oxygen-permeable membrane reactor

A perovskite-type oxide of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) with mixed electronic and oxygen ionic conductivity at high temperatures was used as an oxygen-permeable membrane. A tubular membrane of BSCFO made by extrusion method has been used in the membrane reactor to exclusively transport oxygen for the partial oxidation of ethane (POE) to syngas with catalyst of LiLaNiO/γ-Al₂O₃ at temperatures of 800–900 °C. After only 30 min POE reaction in the membrane reactor, the oxygen permeation flux reached at 8.2 ml cm⁻² min⁻¹. After that, the oxygen permeation flux increased slowly and it took 12 h to reach at 11.0 ml cm⁻² min⁻¹. SEM and EDS analysis showed that Sr and Ba segregations occurred on the used membrane surface exposed to air while Co slightly enriched on the membrane surface exposed to ethane. The oxygen permeation flux increased with increasing of concentration of C₂H₆, which was attributed to increasing of the driving force resulting from the more reducing conditions produced with an increase of concentration of C₂H₆ in the feed gas. The tubular membrane reactor was successfully operated for POE reaction at 875 °C for more than 100 h without failure, with ethane conversion of ∼100%, CO selectivity of >91% and oxygen permeation fluxes of 10–11 ml cm⁻² min⁻¹.     

Photocatalytic degradation of paraquat and genotoxicity of its intermediate products

The photocatalytic degradation of paraquat (1,1-dimethyl-4,4′-bipyridylium dichloride) aqueous solutions in the presence of polycrystalline TiO₂ Degussa P25 irradiated by near-UV light was investigated. The substrate and total organic carbon concentrations were monitored by UV spectroscopy and TOC measurements, respectively: the complete photocatalytic mineralization of paraquat (20 ppm) was achieved after ca. 3 h of irradiation by using 0.4 g l⁻¹ of catalyst amount at natural pH (ca 5.8). On the contrary no significant photodegradation of paraquat was observed in the absence of TiO₂ under similar experimental conditions. To evaluate the genotoxicity of paraquat and its intermediates produced during heterogeneous photocatalytic treatment, in vitro tests such as Ames test, with and without rat liver microsomal fractions (S9 mix), and micronucleus test, were used. Results obtained with Salmonella typhimurium (strain TA100) showed that paraquat and photocatalytic products were unable to induce gene mutations when photocatalysis was used in the presence of the optimum amount of TiO₂, i.e. 0.4 g l⁻¹, whereas an increase of revertants his⁺ per plate was observed after 300 min irradiation in the presence of very low amount of TiO₂ (0.04 g l⁻¹). The negative results from micronucleus test suggest that mutagenic, but non-clastogenic, late intermediates of paraquat photo-oxidation were formed when the photocatalytic runs of paraquat degradation were carried out by using 0.04 g l⁻¹ of photocatalyst.     

Determination of inorganic and total mercury by vapor generation atomic absorption spectrometry using different temperatures of the measurement cell

A simple and inexpensive laboratory-built flow injection vapor generation system coupled to atomic absorption spectrometry (FI-VG AAS) for inorganic and total mercury determination has been developed. It is based on the vapor generation of total mercury and a selective detection of Hg^2 + or total mercury by varying the temperature of the measurement cell. Only the inorganic mercury is measured when the quartz cell is at room temperature, and when the cell is heated to 650 °C or higher the total Hg concentration is measured. The organic Hg concentration in the sample is calculated from the difference between the total Hg and Hg^2 + concentrations. Parameters such as the type of acid (HCl or HNO₃) and its concentration, reductant (NaBH₄) concentration, carrier solution (HCl) flow rate, carrier gas flow rate, sample volume and quartz cell temperature, which influence FI-VG AAS system performance, were systematically investigated. The optimized conditions for Hg^2 + and total Hg determinations were: 1.0 mol l^− 1 HCl as carrier solution, carrier flow rate of 3.5 ml min^− 1, 0.1% (m/v) NaBH₄, reductant flow rate of 1.0 ml min^− 1 and carrier gas flow rate of 200 ml min^− 1. The relative standard deviation (RSD) is lower than 5.0% for a 1.0 μg l^− 1 Hg solution and the limit of quantification (LOQ, 10 s) is 55 ng g^− 1. Certified samples of dogfish muscle (DORM-1 and DORM-2) and non-certified fish samples were analyzed, using a 6.0 mol l^− 1 HCl solution for analyte extraction. The Hg^2 + and CH₃Hg⁺ concentrations found were in agreement with certified ones.     

Microwave-assisted C–H bond activation using a commercial microwave oven for rapid deuterium exchange labeling (C–H → C–D) in carbohydrates

Studies have shown that facile hydrogen → deuterium exchange in two model carbohydrates via stereospecific C–H bond activation could be achieved using a pre-sonicated Raney Nickel^® catalyst and microwave irradiation. Using a simple commercial microwave oven and a silica-gel bath, monosaccharide and disaccharide samples underwent isotopic exchange using microwave irradiation for sequential 15 s intervals. The influence of chilling between irradiation intervals was examined. The results revealed increasing levels of ²H incorporation without either epimerization or concomitant decomposition seen earlier in non-optimized experiments.     

Cu determination in crude oil distillation products by atomic absorption and inductively coupled plasma mass spectrometry after analyte transfer to aqueous solution

Cu was determined in a wide range of petroleum products from crude oil distillation using flame atomic absorption spectrometry (FAAS), electrothermal atomic absorption spectrometry (ETAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Different procedures of sample preparation were evaluated: (i) mineralization with sulfuric acid in an open system, (ii) mineralization in a closed microwave system, (iii) combustion in hydrogen–oxygen flame in the Wickbold's apparatus, (iv) matrix evaporation followed by acid dissolution, and (v) acidic extraction. All the above procedures led to the transfer of the analyte into an aqueous solution for the analytical measurement step. It was found that application of FAAS was limited to the analysis of the heaviest petroleum products of high Cu content. In ICP-MS, the use of internal reference method (with Rh or In as internal reference element) was required to eliminate the matrix effects in the analysis of extracts and the concentrated solutions of mineralized heavy petroleum products. The detection limits (in original samples) were equal to, respectively, 10, 86, 3.3, 0.9 and 0.4 ng g^− 1 in procedures i–v with ETAAS detection and 10, 78, 1.1 and 0.5 ng g^− 1 in procedures i–iii and v with ICP-MS detection. The procedures recommended here were validated by recovery experiments, certified reference materials analysis and comparison of results, obtained for a given sample, in different ways. The Cu content in the analyzed samples was: 50–110 ng g^− 1 in crude oil, < 0.4–6 ng g^− 1 in gasoline, < 0.5–2 ng g^− 1 in atmospheric oil, < 6–100 ng g^− 1 in heavy vacuum oil and 140–300 ng g^− 1 in distillation residue.     

Oxidative thermal degradation of LDPE and the determination of some thermodynamic quantities

The pyrolysis of polyolefin wastes is one of the possible ways to obtain chemical feedstocks. In this work, the thermal degradation of low density polyethylene, (LDPE), which is a major product within plastics, was investigated in a semi-batch reactor system. First-order rate kinetics approach was chosen and reaction rate coefficients, k, and some thermodynamic quantities determined such as activation energy, reaction enthalpy, free activation enthalpy, and entropy of degradation of LDPE for different air flow rates. We found that the maximum value of some thermodynamic quantities, such as reaction rate coefficient is 0.0243 min⁻¹ at 600 mL min⁻¹ air flow rate and the free activation enthalpy (ΔG^≠) is 148.66 kJ mol⁻¹ at 450 mL min⁻¹ air flow rate and the reaction enthalpy (ΔH^≠) is 57.65 J mol⁻¹ at 623 K temperature conditions. Moreover, we found that the oxidative degradation of LDPE is not spontaneous and has lower energy necessary (for degradation) than non-oxidative degradation processes.     

ATP- and redox-induced conformational changes in the activator of the radical enzyme 2-hydroxyisocaproyl-CoA dehydratase

A [4Fe–4S]¹⁺ cluster-containing protein activates 2-hydroxyisocaproyl-CoA dehydratase by an ATP-driven electron transfer. The activator has been proposed to change its conformation by MgATP similarly to nitrogenase Fe-protein. Iron chelation by bathophenanthroline removed the reduced [4Fe–4S]¹⁺ cluster from the activator in an ATP-dependent manner (rate, v = 0.128 ± 0.004 min⁻¹; K_m = 21 ± 1 μM); with ADP no chelation was observed (v < 0.001 min⁻¹). Chelation of the oxidised [4Fe–4S]²⁺ cluster occurred faster with ADP (v = 0.34 ± 0.05 min⁻¹) than with ATP (v = 0.132 ± 0.005 min⁻¹). The data indicate that reduction of the activator and binding of ATP induce conformational changes necessary to transfer the electron to the dehydratase. Interaction of both proteins promotes ATP hydrolysis (K_m = 0.5 ± 0.1 μM).     

In situ quantification of electrochemical dissolution of hafnium-tantalum alloys in acidic media

A thin film hafnium-tantalum combinatorial library with a compositional spread of over 70 at.% was used for electrochemical dissolution experiments in nitric acid. Surface microstructure analysis and crystallographic characterization of individual Hf–Ta alloys confirmed a hexagonal to tetragonal transition from pure Hf to pure Ta accompanied by a change in the surface grain structure. A flow-type scanning droplet cell microscope coupled to downstream analytics was used for the quantification of Hf and Ta dissolution rates along the entire compositional spread. Potentiostatically applying 3 V vs. SHE for 120 s for an electrolyte flow of 0.46 ml min^− 1 resulted in dissolution rates of pure Hf and pure Ta in the ng s^− 1 cm^− 2 and pg s^− 1 cm^− 2 range, respectively. For both species, the average dissolution rate was independent of the compositional gradient, indicating a dissolution enhancement of minor species. A decrease in their activation energy for dissolution triggered by a surface energy modification was the reason for the observed behavior.     

Direct introduction of volatile carbon compounds into the spray chamber of an inductively coupled plasma mass spectrometer: Sensitivity enhancement for selenium

The effect of signal enhancement of elements with ionization potentials in the range from 9 to 11 eV by carbon-containing compounds is a well-known phenomenon in inductively coupled plasma mass spectrometry (ICPMS). It has traditionally been exploited through the addition of organic solvents to the sample matrix or to the mobile phase to improve sensitivity. In the present work, aqueous solutions of volatile carbon compounds (acetone, methanol and acetic acid) were directly introduced into the thermostatted spray chamber rather than being added to the sample matrix. It is presumed that no aerosol is produced from these solutions and only vapors of organic compounds are swept into the plasma together with the sample aerosol. When a 0.40 mol l^− 1 aqueous solution of acetone was introduced directly into the spray chamber, the signals for arsenic and selenium were enhanced by a factor of 4.2. The usefulness of this approach was demonstrated through the achievement of lower instrumental detection limits for selenium at m/z 82 (0.1 ng ml^− 1) compared to the system without direct introduction of volatile carbon compounds (0.5 ng ml^− 1). The method was successfully applied in the determination of traces of selenium in natural water, urine and bovine liver reference material.     

Isopiestic study of (calcium chloride + water) and (calcium chloride + magnesium chloride + water) atT = 313.15 K

The osmotic coefficients of aqueous calcium chloride solutions were experimentally determined atT =  313.15 K by the isopiestic method. Magnesium chloride served as the isopiestic standard for the calculation of osmotic coefficients. The molality range covered in this study correspond to about 0.1mol · kg ^− 1to 3.0mol · kg ^− 1. In addition, the osmotic coefficients of aqueous mixtures of calcium chloride and magnesium chloride were determined over the range of ionic strength levels of about 0.1mol · kg ^− 1to 9mol · kg ^− 1and at various mole fractions. The results obtained were correlated by the Pitzer equation.     

Sensing of 2,4-dichlorophenoxyacetic acid by surface-enhanced Raman scattering

Surface-enhanced Raman scattering (SERS) spectra of the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) was obtained by employing a bi-layer gold substrate, assembled by the reduction of Au(III) over gold-seeded nanoparticles immobilized on functionalized glass substrates. The SERS signal was linear with the logarithm of the solution concentrations between 1.0 × 10⁻⁷ mol L⁻¹ and 1.0 × 10⁻³ mol L⁻¹, indicating that the bi-layer gold substrate affords a significant dynamic range for SERS, providing an excellent analytical response within this concentration range, and revealing the high sensitivity of the gold surface towards such analyte. In addition, using the same gold substrate, a similar calibration curve was obtained for crystal-violet (CV), and it was possible to identify the concentration limit corresponding to the transition from the average SERS to the nonlinear SERS response.     

Highly efficient enzyme immobilization by nanocomposites of metal organic coordination polymers and carbon nanotubes for electrochemical biosensing

New nanocomposites with multi-walled carbon nanotubes (MWCNTs) embedded in metal-organic coordination polymers (MOCPs) were successfully prepared as highly efficient matrices of enzyme immobilization for sensitive electrochemical biosensing. NaAuCl₄ was pre-adsorbed on the MWCNTs to act as anchor sites to further coordinate with ligand benzenedithiol and form MOCPs. The formation of MWCNTs-MOCPs one-pot entrapped glucose oxidase (GOx) with a ratio close to 100% and exhibited enhanced mass-transfer over MOCPs. Thus MWCNTs-MOCPs-modified electrodes present superior enzymatic catalysis performance of greatly enhanced sensitivity (136 μA cm^− 2 mM^− 1) and magnitudes-lower detection limit (48 nM), being superior to most analogues.     

Determination of Hg(II) in waters by on-line preconcentration using Cyanex 923 as a sorbent — Cold vapor atomic absorption spectrometry

Using a solid phase extraction mini-column home-made from a neutral extractant Cyanex 923, inorganic Hg could be on-line preconcentrated and simultaneously separated from methyl mercury. The preconcentrated Hg (II) was then eluted with 10% HNO₃ and subsequently reduced by NaBH₄ to form Hg vapor before determination by cold vapor atomic absorption spectrometry (CVAAS). Optimal conditions for and interferences on the Hg preconcentration and measurement were at 1% HCl, for a 25 mL sample uptake volume and a 10 mL min^− 1 sample loading rate. The detection limit was 0.2 ng L^− 1 and much lower than that of conventional method (around 15.8 ng L^− 1). The relative standard deviation (RSD) is 1.8% for measurements of 40 ng L^− 1 of Hg and the linear working curve is from 20 to 2000 ng L^− 1 (with a correlation coefficient of 0.9996). The method was applied in determination of inorganic Hg in city lake and deep well water (from Changchun, Jilin, China), and recovery test results for both samples were satisfactory.