Determination of234U/238U and235U/238U ratios from commercially available uranium compounds by α-spectrometry

The²³⁴U/²³⁸U and²³⁵U/²³⁸U ratios from uranium compounds by -spectrometry technique have been obtained. Ten commercially available uranium reagents were analyzed. The well-separated peaks corresponding to uranium isotopes are evident, providing an energy spectrum of the -particles of uranium isotopes. It was found that some commerical uranium salts were depleted in²³⁴U and²³⁵U.     

<Superscript>234</Superscript>U/<Superscript>235</Superscript>U activity ratios as a probe for the <Superscript>238</Superscript>U/<Superscript>235</Superscript>U half-life ratio

High-resolution alpha-particle spectrometry was performed on three uranium materials enriched in ²³⁵U. Besides the ²³⁵U peaks, separate peaks belonging to impurity traces of ²³⁴U could be quantified. Relying on the isotopic composition of the uranium, as determined by mass spectrometry, the ratio of the half-lives of ²³⁸U and ²³⁵U was determined via the activity ratio of ²³⁴U and ²³⁵U in the materials. As an intermediate link, the ²³⁴U/²³⁸U half-life ratio was taken from published mass spectrometric analyses of ‘secular equilibrium’ uranium material. The resulting half-life ratio T _1/2(²³⁸U)/T _1/2(²³⁵U) = 6.351±0.031 is in agreement with the commonly adopted half-life values determined by Jaffey et al.     

Determination of U/U atom ratio in uranium samples using liquid scintillation counting (LSC)

A correlation has been developed for the determination of ²³⁵U/²³⁸U atom ratio in uranium samples using liquid scintillation counting (LSC). The ²³⁵U/²³⁸U atom ratio determined by thermal ionization mass spectrometry (TIMS) was correlated to the ratio of (i) α-count rate and (ii) Cerenkov count rate due to ^234mPa in the sample; both measured by LSC. This correlation is linear over the range of ²³⁵U/²³⁸U atom ratio encountered in the nuclear fuel samples, i.e. the low enriched uranium (LEU) samples with ²³⁵U < 20 atom%. The methodology based on this correlation will be useful for the quick determination and verification of ²³⁵U/²³⁸U atom ratios in fuel samples using cost effective technique of LSC.     

<Superscript>234</Superscript>U/<Superscript>238</Superscript>U and <Superscript>235</Superscript>U/<Superscript>238</Superscript>U ratios in domestic water from the environs of Obuasi mine in Ghana

Activity concentrations of ²³⁸U, ²³⁵U and ²³⁴U were determined in different sources of drinking water at the Obuasi gold mines and its surrounding areas in Ghana. Water samples collected from the mines and its surrounding areas were analyzed using direct gamma-ray spectrometry and neutron activation analysis. The ²³⁴U/²³⁸U and ²³⁵U/²³⁸U ratios were calculated and the mean values range from 1.27 to 1.38 and from 0.044 to 0.045 respectively. The average ²³⁴U/²³⁸U ratio was from 1.27 for groundwater to 1.38 for treated water, demonstrating the lack of equilibrium. The average ²³⁵U/²³⁸U activity ratio is 0.045, indicating that only natural uranium was detected in the samples investigated.     

Determination of U isotope ratios in sediments using ICP-QMS after sample cleanup with anion-exchange and extraction chromatography

The determination of uranium is important for environmental radioactivity monitoring, which investigates the releases of uranium from nuclear facilities and of naturally occurring radioactive materials by the coal, oil, natural gas, mineral, ore refining and phosphate fertilizer industries, and it is also important for studies on the biogeochemical behavior of uranium in the environment. In this paper, we describe a quadrupole ICP-MS (ICP-QMS)-based analytical procedure for the accurate determination of U isotope ratios (²³⁵U/²³⁸U atom ratio and ²³⁴U/²³⁸U activity ratio) in sediment samples. A two-stage sample cleanup using anion-exchange and TEVA extraction chromatography was employed in order to obtain accurate and precise ²³⁴U/²³⁸U activity ratios. The factors that affect the accuracy and precision of U isotope ratio analysis, such as detector dead time, abundance sensitivity, dwell time and mass bias were carefully evaluated and corrected. With natural U, a precision lower than 0.5% R.S.D. for ²³⁵U/²³⁸U atom ratio and lower than 2.0% R.S.D. for ²³⁴U/²³⁸U activity ratio was obtained with less than 90 ng uranium. The developed analytical method was validated using an ocean sediment reference material and applied to an investigation into the uranium isotopic compositions in a sediment core in a brackish lake in the vicinity of U-related nuclear facilities in Japan.     

The transfer of uranium from sediment to water along Jucar River, Spain

The effect of sediment size, pH, temperature and conductivity on the transfer of uranium from sediment to water has been studied. The uranium concentration and the²³⁴U/²³⁸U,²³⁵U/²³⁸U activity ratios were measured in water, sediments and suspended matter sampled from Jucar River, using low level alpha-spectrometry. Distribution factors were obtained from these measurements. A more detailed sampling was done in the neighbourhood of the Cofrentes Nuclear Plant (Valencia, Spain). Total uranium activity,²³⁴U/²³⁸U activity ratio and distribution factors for²³⁴U and²³⁸U were found to vary with pH. Leaching and dilution, which depend on pH and salinity, are the probable mechanisms for these changes.     

Studies on the geochemical behaviour of uranium isotopes in coastal environment of the east coast of india

Samples of coastal marine sediments of the East Coast of India were leached with a saturated solution of ammonium carbonate for the extraction of uranium from the sediment particle surface without attacking the mineral core of the particles. All the sediment samples were found to exhibit a²³⁴U/²³⁸U activity ratio in the range of 1.07 to 1.14. On removal of surface organic matter, the²³⁴U/²³⁸U activity ratio is close to 1.00, indicating that the anomaly between²³⁸U and²³⁴U exists only on the labile surface layer. However, no such variations are observed in²³⁵U/²³⁸U activity ratios. These ratios are close to 0.045 which is the same as that of natural uranium.     

Isotopic and ultratrace analysis of uranium by double-focusing sector field ICP mass spectrometry

An analytical method for the ultratrace and isotopic analysis of uranium in radioactive waste samples using a double-focusing sector field ICP mass spectrometer is described. In high-purity water a detection limit for uranium in the lowest fg/mL range has been achieved. Under optimum experimental conditions (²³⁵U/²³⁸U ≈ 1), the precision in ²³⁵U/²³⁸U isotopic ratio determinations has been determined as 0.07% RSD. With the isotopic standard U-020 (²³⁵U/²³⁸U = 0.0208) a precision of 0.23% RSD at the 100 pg/mL level using ultrasonic nebulization has been achieved. With ²³⁴U/²³⁸U isotopic ratios of down to 10^–5, the values obtained by double-focusing sector field ICP-MS and alpha spectrometry were in agreement. Received: 27 February 1997 / Revised: 10 Juni 1997 / Accepted: 12 June 1997     

Uranium analysis in urine by inductively coupled plasma dynamic reaction cell mass spectrometry

Urine uranium concentrations are the best biological indicator for identifying exposure to depleted uranium (DU). Internal exposure to DU causes an increased amount of urine uranium and a decreased ratio of ²³⁵U/²³⁸U in urine samples, resulting in measurements that vary between 0.00725 and 0.002 (i.e., natural and depleted uraniums ²³⁵U/²³⁸U ratios, respectively). A method based on inductively coupled plasma dynamic reaction cell mass spectrometry (ICP-DRC-MS) was utilized to identify DU in urine by measuring the quantity of total U and the ²³⁵U/²³⁸U ratio. The quantitative analysis was achieved using ²³³U as an internal standard. The analysis was performed both with and without the reaction gas oxygen. The reaction gas converted ionized ²³⁵U⁺ and ²³⁸U⁺ into ²³⁵UO₂⁺ (m/z=267) and ²³⁸UO₂⁺ (m/z=270). This conversion was determined to be over 90% efficient. A polyatomic interference at m/z 234.8 was successfully removed from the ²³⁵U signal under either DRC operating conditions (with or without oxygen as a reaction gas). The method was validated with 15 urine samples of known uranium compositions. The method detection limit for quantification was determined to be 0.1 pg U mL^–1 urine and an average coefficient of variation (CV) of 1–2% within the sample measurements. The method detection limit for determining ²³⁵U/²³⁸U ratio was 3.0 pg U mL^–1 urine. An additional 21 patient samples were analyzed with no information about medical history. The measured ²³⁵U/²³⁸U ratio within the urine samples correctly identified the presence or absence of internal DU exposure in all 21 patients.The opinions and assertions expressed herein are those of the authors and are not to be construed as official or as representing the views of the Armed Forces Institute of Pathology, the Department of the Army, or the Department of Defense     

A preliminary investigation of the operational and isotopic speciation of uranium in sediments

Uranium was determined in extracts of inter-tidal sediment, obtained from a contaminated harbour, using the three-stage sequential extraction procedure recommended by BCR. The element was found mainly in association with reducible, or reducible and oxidisable, phases and the overall concentration was enhanced (up to 6.7 μg g^–1 dry weight) with respect to typical, UK levels. The ²³⁸U/²³⁵U ratio has been measured in digests of stream sediments obtained from the vicinity of a uranium enrichment plant. Significant enhancement in ²³⁵U with respect to the natural ²³⁸U/²³⁵U ratio (137.88:1) was observed at some locations.     

Characterization of uranium isotopic abundances in depleted uranium metal assay standard 115

Certified reference material (CRM) 115, Uranium (Depleted) Metal (Uranium Assay Standard), was analyzed using a TRITON Thermal Ionization Mass Spectrometer to characterize the uranium isotope-amount ratios. The certified ²³⁵U/²³⁸U “major” isotope-amount ratio of 0.0020337 (12) in CRM 115 was determined using the total evaporation (TE) and the modified total evaporation (MTE) analytical techniques. In the MTE method, the total evaporation process is interrupted on a regular basis to allow correction of background from peak tailing, internal calibration of the secondary electron multiplier detector versus the Faraday cups, peak-centering, and ion source re-focusing. For the “minor” ²³⁴U/²³⁸U and ²³⁶U/²³⁸U isotope-amount ratio measurements using MTE, precision and accuracy comparable to conventional analyses are achieved, without compromising the quality of the ²³⁵U/²³⁸U isotope-amount ratios. Characterized values of the ²³⁴U/²³⁸U and ²³⁶U/²³⁸U isotope-amount ratios in CRM 115 are 0.000007545 (10) and 0.000032213 (84), respectively. The ²³³U/²³⁸U isotope-amount ratio in CRM 115 is estimated to be <5 × 10^?9. The homogeneity of the CRM 115 materials is established through the absence of any statistically significant unit-to-unit variation in the uranium isotope-amount ratios. The measurements leading to the certification of uranium isotope-amount ratios are discussed.     

Application of Inductively Coupled Plasma Mass Spectrometry to the determination of uranium isotope ratios in individual particles for nuclear safeguards

The capability of inductively coupled plasma mass spectrometry (ICP-MS) for the determination of uranium isotope ratios in individual particles was determined. For this purpose, we developed an experimental procedure including single particle transfer with a manipulator, chemical dissolution and isotope ratio analysis, and applied to the analysis of individual uranium particles in certified reference materials (NBL CRM U050 and U350). As the result, the ²³⁵U/²³⁸U isotope ratio for the particle with the diameter between 0.5 and 3.9 μm was successfully determined with the deviation from the certified ratio within 1.8%. The relative standard deviation (R.S.D.) of the ²³⁵U/²³⁸U isotope ratio was within 4.2%. Although the analysis of ²³⁴U/²³⁸U and ²³⁶U/²³⁸U isotope ratios gave the results with inferior precision, the R.S.D. within 20% was possible for the measurement of the particle with the diameter more than 2.1 μm. The developed procedure was successfully applied to the analysis of a simulated environmental sample prepared from a mixture of indoor dust (NIST SRM 2583) and uranium particles (NBL CRM U050, U350 and U950a). From the results, the proposed procedure was found to be an alternative analytical tool for nuclear safeguards.     

Isotopic analysis of uranium by neutron activation and high resolution gamma ray spectrometry

A method is described for the non-destructive and accurate determination of the isotopic composition of uranium by activation analysis. The high resolving power of Ge(Li) detectors permits easy identification on a single gamma spectrum of the gamma peaks of²³⁹Np formed from²³⁸U by activation and those of fission products formed from²³⁵U. The ratio of the peak intensities is proportional to the²³⁸U/²³⁵U ratio in the sample. A precision of ±0.6% has been obtained.     

Uranium series disequilibrium in the coastal surface sediments and sea water of the Arabian Sea

Nearshore surface sediments from various locations of the West Coast of India were leached by saturated ammonium carbonate solution for the extraction of uranium isotopes. The reagent chosen was found to have high efficiency for leaching uranium isotopes without attacking the mineral core of the sediment particle. The activity ratios of²³⁴U/²³⁸U are in the range of 1.11 to 1.14 and the activity ratios of²³⁵U/²³⁵U are in the range of 0.045 to 0.047. The respective activity ratios in leachates, and residues after removal of surface organic matter from the sediment particles by treatment with hydrogen peroxide and 0.05M HCl, revealed disequilibrium between²³⁸U and²³⁴U only in the surface organic matter. The activity ratios of²³⁴U/²³⁸U and²³⁵U/²³⁸U have also been determined in some seawater samples from the Arabian Sea.     

Behavior of uranium along Jucar River (Eastern Spain): Determination of234U/238U and235U/238U ratios

The uranium concentration and the²³⁴U/²³⁸U,²³⁵U/²³⁸U activity ratios were studied in water samples from Jucar River, using low-level -spectrometry. The effects of pH, temperature and salinity were considered and more detailed sampling was done in the neighbourhood of Cofrentes Nuclear Plant (Valencia, Spain). Changes were observed in the uranium concentration with the salinity and the²³⁴U/²³⁸U activity ratio was found to vary with pH. Leaching and dilution, which depend on pH and salinity, are the probable mechanisms for these changes in the concentration of uranium and the activity ratios.     

Determination of uranium isotopic composition and 236U content of soil samples and hot particles using inductively coupled plasma mass spectrometry

As a result of the accident at the Chernobyl nuclear power plant (NPP) the environment was contaminated with spent nuclear fuel. The ²³⁶U isotope was used in this study to monitor the spent uranium from nuclear fallout in soil samples collected in the vicinity of the Chernobyl NPP. Nuclear track radiography was applied for the identification and extraction of hot radioactive particles from soil samples. A rapid and sensitive analytical procedure was developed for uranium isotopic ratio measurement in environmental samples based on double-focusing inductively coupled plasma mass spectrometry (DF–ICP–MS) with a MicroMist nebulizer and a direct injection high-efficiency nebulizer (DIHEN). The performance of the DF–ICP–MS with a quartz DIHEN and plasma shielded torch was studied. Overall detection efficiencies of 4×10^–4 and 10^–3 counts per atom were achieved for ²³⁸U in DF–ICP–QMS with the MicroMist nebulizer and DIHEN, respectively. The rate of formation of uranium hydride ions UH⁺/U⁺ was 1.2×10^–4 and 1.4×10^–4, respectively. The precision of short-term measurements of uranium isotopic ratios (n = 5) in 1 μg L^–1 NBS U-020 standard solution was 0.11% (²³⁸U/²³⁵U) and 1.4% (²³⁶U/²³⁸U) using a MicroMist nebulizer and 0.25% (²³⁵U/²³⁸U) and 1.9% (²³⁶U/²³⁸U) using a DIHEN. The isotopic composition of all investigated Chernobyl soil samples differed from those of natural uranium; i.e. in these samples the ²³⁶U/²³⁸U ratio ranged from 10^–5 to 10^–3. Results obtained with ICP–MS, α- and γ-spectrometry showed differences in the migration properties of spent uranium, plutonium, and americium. The isotopic ratio of uranium was also measured in hot particles extracted from soil samples.     

Precise isotope ratio measurements for uranium, thorium and plutonium by quadrupole-based inductively coupled plasma mass spectrometry

Precise long-term measurements of uranium and thorium isotope ratios was carried out in 1 μg/L solutions using a quadrupole inductively coupled plasma mass spectrometer (ICP-QMS). The isotopic ratios of uranium (²³⁵U/ ²³⁸U = 1, 0.02 and 0.00725) were determined using a cross-flow nebulizer (CFN, at solution uptake rate of 1 mL/min) and a low-flow microconcentric nebulizer (MCN, at solution uptake rate of 0.2 mL/min) over 20 h. For 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) relative external standard deviations (RESDs) of 0.05% and 0.044% using CFN and MCN, respectively, can be achieved. Additional short term isotope ratio measurements using a direct injection high-efficiency nebulizer (DIHEN) of 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) at a solution uptake rate of 0.1 mL/min yielded an RSD of 0.06–0.08%. The sensitivity of solution introduction by DIHEN for uranium, thorium and plutonium (145 MHz/ppm, 150 MHz/ppm and 177 MHz/ppm, respectively) increased significantly compared to CFN and MCN and the solution uptake rate can be reduced to 1 μL/ min in DIHEN-ICP-MS. Isotope ratio measurements at an ultralow concentration level (e.g. determination of ²⁴⁰Pu/ ²³⁹Pu isotope ratio in a 10 ng/L Pu waste solution) were carried out for the characterization of radioactive waste and environmental samples.     

The determination of235U/238U ratios by activation analysis utilizing high resolution γ-spectrometry

The application of high resolution γ-spectrometry to the direct determination of²³⁵U/²³⁸U isotopic ratios in small uranium samples after neutron activation is reported. The consistency obtained relative to mass spectrometrically determined isotopic ratios is better than 5% for isotopic ratios between 0.06885 and 1.095. The method is not subject to the main disadvantages of the known radiochemical methods for²³⁵U/²³⁸U isotopic ratio determinations, and should be appreciably more rapid compared to the solid-source mass spectrometric method giving the same precision.     

Anomalous behaviour of uranium isotopes in backwater sediments of Zuari river

The surface leaching of the labile component of uranium has been carried out in estuarine sediments of Zuari river in Goa. The measurements of alpha activities of²³⁸U,²³⁵U and²³⁴U in the leachates indicated a remarkable anomaly between the activities of²³⁸U and²³⁴U. The activity ratios of²³⁴U/²³⁸U in these leachates have been found to be in the range of 1.10 to 1.14. However, the activity ratios of²³⁵U/²³⁸U have been found to be 0.045 which is close to that in natural uranium. It has also been observed that the anomaly between²³⁸U and²³⁴U exists only on the surface organic layers of the backwater sediments of the Zuari river.     

Precise isotope ratio measurements for uranium, thorium and plutonium by quadrupole-based inductively coupled plasma mass spectrometry

Precise long-term measurements of uranium and thorium isotope ratios was carried out in 1 μg/L solutions using a quadrupole inductively coupled plasma mass spectrometer (ICP-QMS). The isotopic ratios of uranium (²³⁵U/ ²³⁸U = 1, 0.02 and 0.00725) were determined using a cross-flow nebulizer (CFN, at solution uptake rate of 1 mL/min) and a low-flow microconcentric nebulizer (MCN, at solution uptake rate of 0.2 mL/min) over 20 h. For 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) relative external standard deviations (RESDs) of 0.05% and 0.044% using CFN and MCN, respectively, can be achieved. Additional short term isotope ratio measurements using a direct injection high-efficiency nebulizer (DIHEN) of 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) at a solution uptake rate of 0.1 mL/min yielded an RSD of 0.06–0.08%. The sensitivity of solution introduction by DIHEN for uranium, thorium and plutonium (145 MHz/ppm, 150 MHz/ppm and 177 MHz/ppm, respectively) increased significantly compared to CFN and MCN and the solution uptake rate can be reduced to 1 μL/ min in DIHEN-ICP-MS. Isotope ratio measurements at an ultralow concentration level (e.g. determination of ²⁴⁰Pu/ ²³⁹Pu isotope ratio in a 10 ng/L Pu waste solution) were carried out for the characterization of radioactive waste and environmental samples. Received: 1 December 1998 / Revised: 25 January 1999 / Accepted: 31 January 1999