Trace ion analysis of seawater by capillary electrophoresis: determination of iodide using transient isotachophoretic preconcentration

An improved transient isotachophoresis (tITP) procedure for the preconcentration of iodide from highly saline matrices was developed with the objective to quantify iodide in seawater by capillary electrophoresis (CE). The procedure takes advantage of introducing cetyltrimethylammonium chloride into the high-sodium chloride background electrolyte, which due to a specific interaction with iodide amended placement of the analyte at a large distance from the matrix chloride (the latter performed the role of a leading anion). Computer simulation showed that 2-(N-morpholino)ethanesulfonate could be adopted as a suitable terminating ion to enable isotachophoretic focusing at the beginning of the CE run. Under optimized tITP conditions, the sensitivity response of iodide was improved by a factor of 140 over normal CE mode. This allowed for direct UV detection of as low as 0.6 microg/L iodide and made feasible CE analysis of undiluted surface seawater samples where iodide was found at a 30 microg/L level. The applicability of the proposed tITP-CE method could apparently be extended to the determination of other trace seawater anions (e.g., iodate).     

Iodine speciation in biological samples by capillary electrophoresis-inductively coupled plasma mass spectrometry.

A hyphenation of capillary electrophoresis (CE) to inductively coupled plasma mass spectrometry (ICP-MS) was employed for the speciation of iodine. The separation method used a buffer sandwich of phosphate (pH 2.3), NaOH, sodium dodecyl sulfate (SDS) and borate buffer (pH 8.3) for stacking, aiming at sufficient separation of iodide, iodate, thyroxine (T4) and triiodothyronine (T3). These four iodine species were separated within 15 min and subsequently detected during a pressure-driven detection step (baseline-separated) at 19.5, 29.1, 36.6 and 42.2 s. The detection limits were determined at 0.08 microg I/L (iodide), 0.3 microg I/L (iodate), 3.5 microg I/L (thyroxine) and 2.5 microg I/L (triiodothyronine). This method was applied on iodine speciation in human serum ("healthy" and after thyroid gland operation) and urine. The serum from the healthy person contained iodide (13 microg I/L), T4 (61 microg I/L) and T3 (7.5 microg I/L), whereas the serum from the thyroid-operated person lacked T3. As no "free" I-hormones are known in serum, the role of the thyroid hormone binding globulin (TBG) was investigated. We found that spiked T4 or T3 immediately bound to TBG. Investigations on human urine showed only a peak for iodide.     

Liquid chromatographic determination of less polar ginsenosides in processed ginseng

A novel method for the determination of iodide by size exclusion chromatography was established. The method was simple and highly sensitive with good precision. Iodide was converted to iodine, then sequestered with starch, and separated from the matrix using a Shim-pack DIOL-150 (250 x 7.9 mm) size exclusion column with methanol-0.01 mol l(-1) aqueous phosphoric acid (10:90, v/v) as mobile phase at 1.2 ml min(-1) and UV detection at 224 nm. The calibration graph was linear from 1.0 ng ml(-1) to 100.0 ng ml(-1) for iodide with a correlation coefficient of 0.9992 (n=6). The detection limit was 0.2 ng ml(-1). The method was successfully applied to the determination of iodide in seawater and urine. The recovery was from 92% to 103% and the relative standard deviation was in the range of 1.5% to 3.7%.     

Rapid determination of cyclamate in foods by solid-phase extraction and capillary electrophoresis

A method for the determination of cyclamate in food was developed using solid-phase extraction (SPE) and capillary electrophoresis (CE) with indirect ultraviolet (UV) detection. A 5-10 g sample in 0.1 mol/L hydrochloric acid was homogenized and made up to a volume of 50 mL with 0.1 mol/L hydrochloric acid. After the sample was centrifuged, 25 mL of supernatant was loaded into an Oasis HLB SPE cartridge. The cartridge was washed with 2 mL of demineralized water followed by 2 mL of 50% aqueous methanol, and cyclamate was eluted with 4.5 mL of 50% aqueous methanol. The eluate was added to a solution of sodium propionate (internal standard) for CE analysis. The cyclamate in the eluate was electrophoresed on a fused-silica capillary using 1 mmol/L hexadecyltrimethylammonium bromide and 10 mmol/L potassium sorbate as a running buffer. Detection and reference wavelengths of cyclamate determined with a UV detector were 300 and 254 nm, respectively. The calibration curves for cyclamate showed good linearity in the range of 2-1000 microg/mL and the limits of detection in beverage, fruit in syrup, jam, pickles and confectionary are sample dependent and ranged from 5-10 microg/g. The recovery of cyclamate added at a level of 200 microg/g to various kinds of foods was 93.3-108.3% and the relative standard deviation was less than 4.9% (n=3). A number of commercial samples were analyzed using the proposed method. Cyclamate was detected in one waume, two pickles, and two sunflower seeds. The quantitative values determined with CE correlated to those from high-performance liquid chromatography (HPLC) (the detected values of cyclamate in a sunflower seed measured by CE and HPLC were 3.40 g/kg and 3.51 g/kg, respectively). This analytical method for cyclamate using CE is especially suitable for use in the field.     

Determination of iodide in seawater samples by ion chromatography with chemically-bonded poly(ethylene glycol) stationary phase

An ion chromatographic method for the rapid and direct determination of iodide in seawater is reported. Poly(ethylene glycol) (PEG) groups were chemically bonded onto silica gel or C30-bonded silica gel via diol groups. PEG-bonded C30 binary phases allowed determination of iodide in seawater samples without any interference. Effects of eluent composition on retention behavior of inorganic anions have been investigated. Both cation and anion of the eluent affected the retention of analyte anions. The retention time of anions increased with increasing eluent concentration. The detection limit for iodide obtained by injecting 0.2 microl of sample was 13 microg l(-1) (S/N=3) while the limit of quantitation was 43 microg l(-1) (S/N=10). The present method was successfully applied to the rapid and direct determination of iodide in seawater with long-term durability.     

Capillary electrophoretic determination of sulfite using the zone-passing technique of in-capillary derivatization.

A new capillary electrophoretic (CE) method was developed for the simple and selective determination of sulfite. The proposed method is based on the in-capillary derivatization of sulfite with iodine using the zone-passing technique and direct UV detection of iodide formed. The optimal conditions for the separation and derivatization reaction were established by varying concentration of iodine, electrolyte pH and applied voltage. The optimised separations were carried out in 20 mmol l(-1) Tris-HCl electrolyte (pH 8.5) using direct UV detection at 214 nm. Experimental results showed that the injection of the iodine zone from anodic end of the capillary gives significantly better precision. Common UV absorbing anions such as Br-, l-, S2O3(2-), NO3-, NO2-, SCN- did not give any interferences. Valid calibration (r2=0.998) is demonstrated in the range 1 x 10(-5) - 8 x 10(-4) mol l(-1) of sulfite. The detection limit (SIN=3) was 2 x 10(-6) mol l(-1). The proposed system was applied to the determination of free sulfite in wines. The recovery tests established for wine samples were within the range 92-103%. The CE results were compared with those obtained by iodometric titration technique.     

Determination of trace metals by capillary electrophoresis

A new analytical procedure is developed using a strong complexing agent, 1,10-phenanthroline (Phen), for direct UV detection of Zn, Mn, Cu, Co, Cd, and Fe at microg/L concentrations in environmental water samples. The metal chelates formed showed different electrophoretic mobilities and solved the comigration problem for capillary electrophoresis (CE) separation of free metal ions. To obtain stable metal-Phen chelates during the capillary zone electrophoresis (CZE) run, both pre-column and on-column complexation are required and threefold excess of Phen over metal ions should be added to the sample. The optimized background electrolyte (BGE) consists of 30 mM hydroxylamine hydrochloride and 0.1% methanol at pH 3.6. Under hydrodynamic sampling, CE run at + 20 kV in 65 cm x 0.05 mm ID fused-silica column with detection at 265 nm, baseline separation, satisfactory working ranges (10 microg/L to 5.5 mg/L), sensitive detection limits (1-3 microg/L), good repeatability for migration times (relative standard deviation, RSD 0.36-0.81%, n = 5), peak area (RSD 3.2-4.2%, n = 5) and peak height (RSD 3.2-4.5%, n = 5) were obtained for the metal cations investigated. The reliability of the method was established by parallel determination using the inductively coupled plasma-atomic emission spectrometry (ICP-AES) method giving results within statistical variation. The procedure developed is shown to provide a quick, sensitive, precise, and economic method for simultaneous determination of metal cations that can form stable chelates with Phen.     

Determination of total inorganic iodine in seawater by cathodic stripping square wave voltammetry

A method has been designed for the reduction of iodate to iodide in seawater and subsequent determination of total dissolved iodine as iodide by cathodic stripping square wave voltammetry. The pH of the sample is lowered to about 1-2 and iodate is reduced to iodide with sodium sulfite under this acidic condition. The pH of the sample is then raised to 8-9 before the concentration of iodide is measured.     

Capillary electrophoretic determination of thiosulfate,sulfide and sulfite using in-capillary derivatization with iodine

A new capillary electrophoresis (CE) method was developed for the rapid, simple and selective determination of thiosulfate, sulfide and sulfite species. The proposed method is based on the in-capillary derivatization of separated sulfur anions by mixing their zones with the iodine zone during the electrophoretic migration and direct UV detection of iodide formed. The optimal conditions for the separation and derivatization reaction were established by varying electrolyte pH, electrolyte counter-ion, concentration of iodine, and applied voltage. The optimized separations were carried out in 20 mmol/L Tris-chloride electrolyte (pH 8.5) using direct UV detection at 214 nm. All three sulfur species were well resolved in less than 4 min. The method gives repeatability comparable or even better than this obtained for sulfur anions using standard CE technique. The proposed CE system was applied to the monitoring of sulfur anions in spent fixing solutions during the electrolytic oxidation.     

Head-space flow injection for the on-line determination of iodide in urine samples with chemiluminescence detection

A simple head-space (HS) flow injection (FI) system with chemiluminescence (CL) detection for the determination of iodide as iodine in urine is presented. The iodide is converted to iodine by potassium dichromate under stirring in the closed HS vial, and the iodine is released from urine by thermostatting and is carried in a nitrogen flow through an iodide trapping solution. The concomitant introduction of aliquots of iodine, luminol and cobalt(II) solutions by means of a time-based injector into an FI system allowed its mixing in a flow-through cell in front of the detector. The emission intensity at 425 nm was recorded as a function of time. The salting-out of the standard solutions affected the gas-liquid distribution coefficient of iodine in the HS vial. The typical analytical working graphs obtained under the optimized experimental conditions were rectilinear from 0 to 5 mg l(-1) iodine, achieving a precision of 2.3 and a relative standard deviation of 1.8 for ten replicate analyses of 50 and 200 microg l(-1) iodine. However, a second-order process becomes significant at higher iodine concentrations (from 10 to 40 mg l(-1)). The detection limit of the method is 10 microg l(-1) (80 ng) iodine when 8 ml samples are taken. Data for the iodide content of 10 urine samples were in good agreement with those obtained by a conventional catalytic method, and recoveries varied between 101 and 103% for urine samples spiked with different amounts of iodide. The analysis of one sample takes less than 20 min. In the present study the iodide levels found for 100 subjects were 86.8 +/- 19.0 (61-125) microg l(-1), which is lower than the WHO's optimal level (150-300 microg per day).     

A sensitive extracto-photometric method for determination of residual chlorine in greywater

A new photometric method for chlorine determination based on the oxidative transformation of iodide to iodine and subsequent extraction in ethyl acetate has been developed. The effects of several chemical variables (pH, ionic strength, and iodide concentration) have been studied. Characteristics of the method were linear range 0-0.6 mg C12/L, limit of detection 5 microg Cl2/L, and coefficient of variation 0.6%. The method has been applied to greywater without previous sample treatment.     

Simple spectrophotometric and titrimetric methods for the determination of sulfur dioxide.

The proposed work describes a simple spectrophotmetric as well as a titrimetric method to determine sulfur dioxide. The spectrophotometric method is based on a redox reaction between sulfur dioxide and iodine monochloride obtained from iodine with chloramine-T in acetic acid. The reagent iodine monochloride oxidizes sulfur dioxide to sulfate, thereby reducing itself to iodine. Thus liberated iodine will also oxidize sulfur dioxide and reduce itself to iodide. The obtained iodide is expected to combine with iodine to form a brown-colored homoatomictriiodide anion (460 nm), which forms an ion-pair with the sulfonamide cation, providing exceptional color stability to the system under an acidic condition, and is quantitatively relatd to sulfur dioxide. The system obeys Beer's law in the range 5 - 100 microg of sulfur dioxide in a final volume of 10 ml. The molar absorptivity is 5.03 x 10(3) l mol(-1)cm(-1), with a relative standard deviation of 3.2% for 50 microg of sulfur dioxide (n = 10). In the titrimetric method, the reagent iodine monochloride was reduced with potassium iodide (10%) to iodine, which oxidized sulfur dioxide to sulfate, and excess iodine was determined with a thiosulfate solution. The volume difference of thiosulfate with the reagent and with the sulfur dioxide determined the sulfur dioxide. Reproducible and accurate results were obtained in the range of 0.1 - 1.5 mg of sulfur dioxide with a relative standard deviation of 1.2% for 0.8 mg of sulfur dioxide (n = 10).     

在线样品前处理大体积进样离子色谱法直接测定海水中亚硝酸盐、硝酸盐和磷酸盐

采用戴安公司谱睿(Pre)在线样品除氯技术,结合OnGuard Ba柱去除硫酸盐,建立了离子色谱直接测定海水中亚硝酸盐、硝酸盐和磷酸盐的方法。该方法以IonPac AG23为富集柱,高容量IonPac AS23为分离柱,淋洗液自动发生装置在线产生KOH溶液进行梯度淋洗,抑制电导检测。实验结果表明: 样品稀释5～10倍时,直接进样不会干扰目标物测定。当流速为1 mL/min、进样量为500 μL时,海水中NO~2-N、NO~3-N、PO3~4-P的方法检出限分别为0.3、0.4、0.2 μg/L,线性范围分别为10～500 μg/L、14～680 μg/L、3.4～170 μg/L,线性相关系数r均大于0.9990。测得人工海水样品中目标物的加标回收率为92%～106%,相对标准偏差(RSD, n=6)为1.2%～7.7%。该方法一次进样可在13 min内完成分析,具有操作简单快捷、无污染等优点,能满足近海海水中NO~2、NO~3、PO3~4的定量分析要求。     

In-capillary derivatization and determination of iodine in sodium chloride solution

A new capillary electrophoretic (CE) method was developed for the simple and selective determination of iodine in 0.5 mol l(-1) NaCl. The proposed method is based on the in-capillary derivatization of iodine with thiosulfate ions using the zone-passing technique and direct photometric detection of the iodide and tetrathionate formed. The optimal conditions for the separation and derivatization reaction were established by varying the concentration of iodine, electrolyte pH and applied voltage. The optimized separations were carried out in phosphate electrolyte (pH 6.86) using direct photometric detection at 253.7 nm. Common photometric detection absorbing anions such as Cl(-), NO(2)(-), S(2)O(3)(2-) did not give any interference. Valid calibration (r(2) = 0.994) is demonstrated in the range 16.5-198.1 mg l(-1) of iodine. The detection limit (calculated according to K. Doerffel, Statistik in der analytischen Chemie, 1990) was 11.53 mg l(-1) (by iodide peak area) and 8.45 mg l(-1) (by tetrathionate peak area). The proposed system was applied to the determination of iodine after oxidation of iodide in underground water.     

Simultaneous determination of iodide and iodate in seawater by transient isotachophoresis-capillary zone electrophoresis with artificial seawater as the background electrolyte

We developed capillary zone electrophoresis with transient isotachophoresis (ITP) as an on-line concentration procedure for simultaneous determination of iodide and iodate in seawater. The effective mobility of iodide was decreased by addition of 20 mM cetyltrimethylammonium chloride to an artificial seawater background electrolyte so that transient ITP functioned for both iodide and iodate. Limits of detection for iodide and iodate were 4.0 and 5.0 microg/l (as iodine) at a signal-to-noise ratio of 3. Values of the relative standard deviation of peak area, peak height, and migration times for iodide and iodate were 2.9, 1.3, 1.0 and 2.3, 2.1, 1.0%, respectively. The proposed method was applied to simultaneous determination of iodide and iodate in seawater collected at a pond at our university.     

Large-volume sample stacking for analysis of ethylenediaminetetraacetic acid by capillary electrophoresis

A simple, quick, and sensitive capillary electrophoretic technique-large volume stacking using the electroosmotic flow (EOF) pump (LVSEP) - has been developed for determining ethylenediaminetetraacetic acid (EDTA) in drinking water for the first time. It is based on a precapillary complexation of EDTA with Fe(III) ions, followed by large-volume sample stacking and direct UV detection at 258 nm. The curve of peak response versus concentration was linear from 5.0 to 600.0 microg/L, and 0.7 to 30.0 mg/L. The regression coefficients were 0.9988 and 0.9990, respectively. The detection limit of the current technique for EDTA analysis was 0.2 microg/L with an additional 10-fold preconcentration procedure, based on the signal-to-noise ratio of 3. As opposed to the classical capillary zone electrophoresis (CE) method, the detection limit was improved about 1000-fold by using this LVSEP method. To the best of our knowledge, it represents the highest sensitivity for EDTA analysis via CE. Several drinking water samples were tested by this novel method with satisfactory results.     

Spectrophotometric determination of iodine species in table salt and pharmaceutical preparations

A sensitive spectrophotometric method for the determination of iodine species like iodide, iodine, iodate and periodate is described. The method involves the oxidation of iodide to ICl(2)(-) in the presence of iodate and chloride in acidic medium. The formed ICl(2)(-) bleaches the dye methyl red. The decrease in the intensity of the colour of the dye is measured at 520 nm. Beer's law is obeyed in the concentration range 0-3.5 microg of iodide in an overall volume of 10 ml. The molar absorptivity of the colour system is 1.73 x 10(5) l mol(-1) cm(-1) with a correlation coefficient of -0.9997. The relative standard deviation is 3.6% (n=10) at 2 microg of iodide. The developed method can be applied to samples containing iodine, iodate and periodate by prereduction to iodide using Zn/H(+) or NH(2)NH(2)/H(+). The effect of interfering ions on the determination is described. The proposed method has been successfully applied for the determination of iodide and iodate in salt samples and iodine in pharmaceutical preparations.     

Application of CE with novel dynamic coatings and field-amplified sample injection to the sensitive determination of isomeric benzoic acids in atmospheric aerosols and vehicular emission

A simple and reliable CE method with direct UV detection has been developed to separate eight isomeric benzoic acids in atmospheric aerosols and vehicular emission without complex sample pretreatment. Optimal electrophoretic conditions, with migration times under 5 min, were obtained by using a 50 mM acetate buffer (pH 4.7) containing a dynamic surface coating EOTrol LN (0.005% w/v). The separations were carried out in a cathode to anode direction (-30 kV) allowing the low cathodal EOF ( approximately 1 x 10(-9) m(2)V(-1)s(-1)) to extend the effective separation by slowing the movement of the studied aromatic acids. Moreover, the sensitivity of the method at 200 nm was enhanced by using a field-amplified sample injection (FASI) with electrokinetic (EK) sample injection (-2 kV, 60 s). Prior to sample injection, a short water plug (3 s at 0.5 psi) was introduced. Under these conditions, the method was capable of detecting the analytes in deionized water with LODs (S/N = 3) as low as 0.1 microg/L for most of the studied acids. In the presence of 10 mg/L of sulphate (added to simulate a sample matrix), LODs ranged from 0.26 to 0.62 microg/L. The validation of the method has proven an excellent separation performance and accuracy for the determination of isomeric benzoic acids in the studied matrices.     

Flow injection atomic absorption spectrometric determination of iodide using an on-line preconcentration technique

A continuous flow atomic absorption spectrometric system was used to develop an efficient on-line preconcentration-elution procedure for the determination of iodide traces. Chromium (VI) is introduced into the flow system and is reduced to chromium (III) in acid medium proportionally to the iodide present in the sample. The Cr(III) reduced by iodide is retained on a minicolumn packed with a poly(aminophosphonic acid) chelating resin, while unreduced Cr(VI) is not retained. Reduced Cr(III) is preconcentrated by passing the sample containing iodide through the system during 3 min, and is then eluted with 0.5 mol L(-1) hydrochloric acid and determined by flame atomic absorption spectrometry (FAAS). The detection limit (3sigma) obtained is 2.5 microg L(-1). Other ions typically present in waters do not interfere. The proposed method allows the determination of iodide in the range 6-220 microg L(-1) with a relative standard deviation of 2.7% at a rate of 17 samples h(-1). The method has been applied to the determination of iodide in tap and sea waters.     

Rapid and direct determination of iodide in seawater by electrostatic ion chromatography

An electrostatic ion chromatographic (IC) method for rapid and direct determination of iodide in seawater is reported. Separation was achieved using a reversed-phase ODS packed column (250x4.6 mm I.D.) modified by coating with Zwittergent-3-14 micelles, with an eluent comprising an aqueous solution containing 0.2 mM NaClO4 and 0.3 mM Zwittergent-3-14 and using UV detection at 210 nm. Samples prepared by dissolving NaIO3, NaNO2, NaBr, NaBrO3, NaNO3, NaI, and NaSCN in artificial or real seawaters were analyzed using this IC system. Nitrite, iodate, bromide, bromate, and nitrate showed very little or no retention, while iodide and thiocyanate were well separated, being eluted within 6 and 16 min, respectively. The detection limit for iodide obtained by injecting 400 microL of sample was 0.011 microM (S/N = 3), and the precision values obtained by analyzing samples containing 0.1 or 0.3 microM iodide in real seawater samples were 2.3% RSD and 1.2% RSD, respectively. Direct determination of iodide in real seawater samples was possible using this proposed IC system.