Solar active nano-TiO2 for mineralization of Reactive Red 120 and Trypan Blue: 1st Nano Update

Nano-TiO₂ was synthesized by sol–gel method. The catalyst was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) images, transmission electron microscope (TEM), BET surface area measurement and DRS analysis. The formation of anatase phase nano-TiO₂ was confirmed by XRD measurements and its crystalline size is found to be 15.2 nm. SEM images depict the crystalline nature of prepared TiO₂. The BET surface area of prepared TiO₂ is found to be 86.5 m² g^?1 which is higher than that of commercially available TiO₂–P25. The photocatalytic activity of prepared anatase phase TiO₂ has been tested for the degradation of two azo dyes: Reactive Red 120 (RR 120) and Trypan Blue (TB) using solar light. The photocatalytic activity of nano-TiO₂ is higher than TiO₂–P25 under solar light. The mineralization of dyes has been confirmed by chemical oxygen demand (COD) measurements.     

F–B-codoping of anodized TiO2 nanotubes using chemical vapor deposition

Chemical vapor deposition (CVD) was firstly used to simultaneously codope fluorine and boron into TiO₂ nanotubes anodized Ti in C₂H₂O₄ · 2H₂O + NH₄F electrolyte. F–B-codoping was successfully carried out by annealing the anodized TiO₂ nanotubes through CVD, as evidenced from XPS analysis. SEM images showed that the higher the annealing temperature, the greater structure damage of F–B-codoped sample. XRD results confirmed that annealing temperature had an influence on the phase structure and boron and fluorine impurities could retard anatase–rutile phase transition. F–B-codoped samples displayed remarkably strong absorption in both UV and visible range. Under visible-light irradiation, F–B-codoped samples showed the higher I_ph and catalytic activity in methyl orange photoelectrodegradation than F-doped sample and B-doped sample. This showed a convincing evidence of F–B-codoping of TiO₂ had an obvious synergistic effect on the enhancement of photocurrents and photoelectrocatalytic activity.     

Molecular dynamics simulations of adsorption of hydrophobic 1,2,4-trichlorobenzene (TCB) on hydrophilic TiO2 in surfactant emulsions and experimental process efficiencies of photo-degradation and -dechlorination

Molecular dynamics simulations have been carried out to assess event details in the adsorption of the hydrophobic substrate 1,2,4-trichlorobenzene (TCB) on the hydrophilic TiO₂ particle surface in the presence of the biosurfactant 4-O-(4′,6′-di-O-acetyl-2′,3′-di-O-alkanoyl-β-d-mannopyranosyl)-d-erythritol (MEL) and the SDS (sodium dodecylsulfate) surfactant in aqueous media at ambient temperature with interaction forces between organic molecules and TiO₂ calculated from Lennard–Jones and Coulomb potential models. The surfactant and the TCB substrate were arranged in the vicinity of TiO₂ using 768 water molecules in the simulations. Results indicate that the MEL molecules adsorb on the TiO₂ surface in ca. 5 ps (k = 2 × 10¹¹ s^?1) through the oxygen atoms of the hydrophilic functions. Contact distance between the MEL and the TiO₂ surface shortened further after 10 ps with adsorption controlled mostly by van der Waals’ forces. The TCB molecules are trapped within the alkyl chains of the MEL system, which subsumes TCB to a greater extent by the repulsion of water, thereby facilitating the TCB molecules to approach the highly hydrophilic and positively charged TiO₂ particle surface. Along with the simulations, also examined was the photodegradation of this hydrophobic TCB substrate that takes place at the TiO₂/water interface in the presence of the MEL biosurfactant. For comparison, the advantages of the MEL in this task and of the commonly used SDS surfactant were determined under otherwise identical experimental conditions (200 mg L^?1 of surfactants) by examining the dynamics of the photo-induced degradation and dechlorination of TCB. The photodegradation of TCB was nearly quantitative in MEL/TiO₂ in contrast to only ca. 22% complete in SDS/TiO₂ dispersions. It is deduced that wastewater treatments with the highly hydrophilic TiO₂ are seriously limited in their photodegradation of hydrophobic pollutants, an issue easily resolvable by the presence of biodegradable surfactants.     

Mesoporous TiO2−xAy (A = N,S) as a visible-light-response photocatalyst

Mesoporous TiO_2?xA_y (A = N, S) thin films were fabricated using thiourea as a doping resource by a combination of sol-gel and evaporation-induced self-assembly (EISA) processes. The results showed that thiourea could serve two functions of co-doping nitrogen and sulfur and changing the mesoporous structure of TiO₂ thin films. The resultant mesoporous TiO_2?xA_y (A = N, S) exhibited anatase framework with a high porosity and a narrow pore distribution. The formation of the O–Ti–N and O–Ti–S bonds in the mesoporous TiO_2?xA_y (A = N, S) were substantiated by the XPS spectra. A new bandgap in visible light region (520 nm) corresponding to 2.38 eV could be formed by the co-doping. After being illuminated for 3 h, methyl orange could be degraded nearly completely by the co-doped sample under both ultraviolet irradiation and visible light illumination. While pure mesoporous TiO₂ could only degrade 60% methyl orange under UV illumination and showed negligible photodegradation capability in the visible light range. Furthermore, the photo-induced hydrophilic activity of TiO₂ film was improved by the co-doping. The mesoporous microstructure and high visible light absorption could be attributed to their good photocatalytic acitivity and hydrophilicity.     

Temporal evolution study of the plasma induced by CO2 pulsed laser on targets of titanium oxides

This paper reports studies on time-resolved laser induced breakdown spectroscopy (LIBS) of plasmas induced by IR nanosecond laser pulses on the titanium oxides TiO and TiO₂ (anatase). LIBS excitation was performed using a CO₂ laser. The laser-induced plasma was found strongly ionized yielding Ti⁺, O⁺, Ti^2 +, O^2 +, Ti^3 +, and Ti^4 + species and rich in neutral titanium and oxygen atoms. The temporal behavior of specific emission lines of Ti, Ti⁺, Ti^2 + and Ti^3 + was characterized. The results show a faster decay of Ti^3 + and Ti^2 + ionic species than that of Ti⁺ and neutral Ti atoms. Spectroscopic diagnostics were used to determine the time-resolved electron density and excitation temperatures. Laser irradiation of TiO₂-anatase induces on the surface sample the polymorphic transformation to TiO₂-rutile. The dependence on fluence and number of irradiation pulses of this transformation was studied by micro-Raman spectroscopy.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

Mesoporous TiO2 nano networks: Anode for high power lithium battery applications

Anatase phase mesoporous TiO₂ with I41/amd space group was synthesized via the urea assisted hydrothermal method. The existence of mono phasic TiO₂ sub-microspheres of uniform particle size (ca. 400 nm) encompassing an average crystallite size of 14 nm was demonstrated using the XRD, FE-SEM and TEM analysis. Surface area of ca. 116.49 m²/g along with a pore size of 7 nm was calculated using the BET and adsorption isotherm measurements which authenticated the mesoporous nature of the synthesized material. Suitable calcination temperature for the better electrochemical property was established via the optimization process. Accordingly, the mesoporous TiO₂ calcined at 400 °C displayed improved cycleability with excellent rate capability ever reported, even at 20 C-rate of discharge. The reason for the superior rate capability is corroborated to the highly mesoporous nature of the TiO₂ sub-microspheres that has imparted desirable surface area apposite for enhanced ionic and electronic diffusion.     

A novel approach for determining total titanium from titanium dioxide nanoparticles suspended in water and biosolids by digestion with ammonium persulfate

Titanium dioxide (i.e. TiO₂) in nano-form is a constituent of many nanomaterials that are used in sunscreens, cosmetics, industrial products and in biomedical applications. Quantification of TiO₂ nanoparticles in various matrixes is a topic of great interest for researchers studying the potential health and environmental impacts of nanoparticles. However, analysis of TiO₂ as Ti⁴⁺ is difficult because current digestion techniques require use of strong acids that may be a health and safety risk in the laboratory. To overcome this problem, we developed a new method to digest TiO₂ nanoparticles using ammonium persulfate as a fusing reagent. The digestion technique requires short times to completion and optimally requires only 1 g of fusing reagent. The fusion method showed >95% recovery of Ti⁴⁺ from 6 μg mL^?1 aqueous suspensions prepared from 10 μg mL^?1 suspension of different forms of TiO_2, including anatase, rutile and mixed nanosized crystals, and amorphous particles. These recoveries were greater than open hot-plate digestion with a tri-acid solution and comparable to microwave digestion with a tri-acid solution. Cations and anions commonly found in natural waters showed no significant interferences when added to samples in amounts of 10 ng to 110 mg, which is a much broader range of these ions than expected in environmental samples. Using ICP-MS for analysis, the method detection limit (MDL) was determined to be 0.06 ng mL^?1, and the limit of quantification (LOQ) was 0.20 ng mL^?1. Analysis of samples of untreated and treated wastewater and biosolids collected from wastewater treatment plants yielded concentrations of TiO₂ of 1.8 and 1.6 ng mL^?1 for the wastewater samples, respectively, and 317.4 ng mg^?1 dry weights for the biosolids. The reactions between persulfate ions and TiO₂ were evaluated using stoichiometric methods and FTIR and XRD analysis. A formula for the fusing reaction is proposed that involves the formation of sulfate radicals.     

Optical and dielectric properties of isothermally crystallized nano-KNbO3 in Er3+-doped K2O–Nb2O5–SiO2 glasses

Precursor glass of composition 25K₂O–25Nb₂O₅–50SiO₂ (mol%) doped with Er₂O₃ (0.5 wt% in excess) was isothermally crystallized at 800 °C for 0–100 h to obtain transparent KNbO₃ nanostructured glass–ceramics. XRD, FESEM, TEM, FTIRRS, dielectric constant, refractive index, absorption and fluorescence measurements were carried out to analyze the morphology, dielectric, structure and optical properties of the glass–ceramics. The crystallite size of KNbO₃ estimated from XRD and TEM is found to vary in the range 7–23 nm. A steep rise in the dielectric constant of glass–ceramics with heat-treatment time reveals the formation of ferroelectric nanocrystalline KNbO₃ phase. The measured visible photoluminescence spectra have exhibited green emission transitions of ²H_11/2, ⁴S_3/2 → ⁴I_15/2 upon excitation at 377 nm (⁴I_15/2 → ⁴G_11/2) absorption band of Er³⁺ ions. The near infrared (NIR) emission transition ⁴I_13/2 → ⁴I_15/2 is detected around 1550 nm on excitation at 980 nm (⁴I_15/2 → ⁴I_11/2) of absorption bands of Er³⁺ ions. It is observed that photoluminescent intensity at 526 nm (²H_11/2 → ⁴I_15/2), 550 nm (⁴S_3/2 → ⁴I_15/2) and 1550 nm (⁴I_13/2 → ⁴I_15/2) initially decrease and then gradually increase with increase in heat-treatment time. The measured lifetime (τ_f) of the ⁴I_13/2 → ⁴I_15/2 transition also possesses a similar trend. The measured absorption and fluorescence spectra reveal that the Er³⁺ ions gradually enter into the KNbO₃ nanocrystals.     

Synthesis and studies on photochromic properties of vanadium doped TiO2 nanoparticles

Pure and (0.5–3 at%) vanadium doped TiO₂ nanoparticles have been synthesized by wet chemical method. The as synthesized materials have been characterized by using XRD, atomic force microscope (AFM), Raman, EPR and UV–vis spectroscopy techniques. From XRD studies, both pure as well as vanadium doped TiO₂ have been found to show pure anatase phase. The value of lattice constant c is smaller in doped TiO₂ as compared to undoped and has been found to decrease with increase in vanadium concentration. AFM studies show formation of spherical particles with particle size ～23 nm in all the samples. Photochromic behavior of these materials has been studied by making their films in alkyd resin. Vanadium doped TiO₂ films show reversible change in color from beige-yellow to brownish violet on exposure to UV light. The mechanism of coloration and bleaching process has been discussed.     

X-ray induced photocatalysis on TiO2 and TiO2 nanotubes: Degradation of organics and drug release

The photocatalytic activity of titanium dioxide under X-ray radiation is of great interest for biomedical applications. In the present work we explore the use of compact TiO₂ layers and TiO₂ nanotubes for X-ray induced photocatalysis, in particular the degradation of organics and monolayer chain scission for drug release. The radiation was done with a conventional X-ray source and doses up to 50 × 10^?3 J/kg. The results show the feasibility of X-ray catalysis on TiO₂ and X-ray induced monolayer chain scission by the release of surface attached Zn–porphyrin molecules. Furthermore, a higher efficiency for anatase films and nanotubes is obtained than for amorphous morphologies.     

Bi2O3 deposited on highly ordered mesoporous carbon for supercapacitors

A simple route has been employed to prepare nanosized Bi₂O₃ deposited on highly ordered mesoporous carbon. The electrochemical measurements reveal that, by loading only 10% Bi₂O₃ on the mesoporous carbon, the specific capacitance of the composite is improved by 62%, with the maximum value reaching 232 F g^?1 at a sweep rate of 5 mV s^?1. The specific capacitance of Bi₂O₃ is calculated and reaches 1305 F g^?1 at 1 mV s^?1. It is found that the mass transfer in the framework of the crystalline oxide is still difficult in spite of its nanosize, as evidenced by the decline of the specific capacitance of the Bi₂O₃ with the increase of the sweep rate. The cyclic life of composite materials is also measured and the capacitance only declines 21% after 1000 cycles.     

High-surface-area microporous carbon as the efficient photocathode of dye-sensitized solar cells

This paper reports on the application of cornstalks-derived high-surface-area microporous carbon (MC) as the efficient photocathode of dye-sensitized solar cells (DSCs). The photocathode, which contains MC active material, Vulcan XC–72 carbon black conductive agent, and TiO₂ binder, was obtained by a doctor blade method. Electronic impedance spectroscopy (EIS) of the MC film uniformly coated on fluorine doped SnO₂ (FTO) glass displayed a low charge-transfer resistance of 1.32 Ω cm². Cyclic voltammetry (CV) analysis of the as-prepared MC film exhibited excellent catalytic activity for I₃^?/I^? redox reactions. The DSCs assembled with the MC film photocathode presented a short-circuit photocurrent density (J_sc) of 14.8 mA cm^?2, an open-circuit photovoltage (V_oc) of 798 mV, and a fill factor (FF) of 62.3%, corresponding to an overall conversion efficiency of 7.36% under AM 1.5 irradiation (100 mW cm^?2), which is comparable to that of DSCs with Pt photocathode obtained by conventional thermal decomposition.     

Synthesis,characterization and photocatalytic performance of W,N, S-tri-doped TiO2 under visible light irradiation

W–S–N-tri-doped TiO₂ photocatalysts (WSNTiO₂) were prepared by a simple sol–gel method. Tungstic acid, sodium sulfate and urea were used as tungsten, sulfur and nitrogen sources, respectively. The morphology and microstructure characteristics of the photocatalysts were evidenced by means of XRD, BET, TEM, SEM and UV–vis DRS techniques. The XRD results show that the main crystal phase of samples is anatase. It was also found that the tri-doping of TiO₂ increases its BET specific surface area from 95 to 121 m²·g⁻¹. Besides, it was shown that tri-doping narrows the band gap of TiO₂ effectively, which has greatly improved the photocatalytic activity in the visible light region. The photocatalytic activity of tri-doped TiO₂ powders was compared to that of bi-doped ones through the degradation of Congo Red (CR) under visible irradiation. Thus, the prepared 0.5% W–N–S–TiO₂ heat treated at 450 °C showed the best photocatalytic activity compared to the prepared pure TiO₂, Degussa P25, and co-doped samples (WNTiO₂ and WSTiO₂). In particular, a Congo Red degradation rate of approximately 99% was reached after only 35 min of visible light irradiation in the presence of 0.5% of WNSTiO₂. Total organic carbon (TOC) removal of CR was up to 72% and confirmed its significant mineralization in the presence of 0.5% of WNSTiO₂ photocatalyst.     

Phosphatization: A promising approach to enhance the performance of mesoporous TiO2 anode for lithium ion batteries

We report phosphatization is a promising method to enhance the performance of mesoporous TiO₂ anode for lithium ion batteries. The resulting phosphated mesoporous TiO₂ possessed higher reversible capacity and better cycling stability than the pure mesoporous TiO₂. When cycled at 30 mA/g between 3.0 and 1.0 V, the initial capacity of phosphate mesoporous TiO₂ was 249 mA h/g, significantly higher than that of pure mesoporous TiO₂ (204 mA h/g). After 40 cycles, the capacity retention ratio of phosphate mesoporous TiO₂ reached 83.7%, while pure mesoporous TiO₂ had merely a capacity retention ratio of 62.3%. We believe that this phosphatization process could be used to enhance the electrochemical performance of other metal oxides for lithium ion batteries.     

Operando soft x-ray emission spectroscopy of LiMn2O4 thin film involving Li–ion extraction/insertion reaction

We developed an electrochemical in situ cell for soft x-ray emission spectroscopy (XES) to accurately investigate the redox reaction and electronic structure of transition metals in the cathode materials for Li–ion battery. The in situ cell consists of a Li–metal counter electrode, an organic electrolyte solution, and a cathode on a membrane window which separates the liquid electrolyte from high vacuum and can pass the incoming and emitted photons. In this study, the Mn 3d electronic structure of LiMn₂O₄ thin-film electrode was clarified by the operando XES. At the charged state, the XES spectrum changed significantly from the open-circuit-voltage (OCV) state, suggesting oxidation of the Mn^3 + component through Li–ion extraction. Upon discharge up to 3.0 V vs. Li/Li⁺, the XES spectrum almost returned to its profile at the OCV state with small difference, indicating the valence change of Mn: Mn^3.6 + → Mn^4 + → Mn^3.3 + corresponding to the OCV, charged, and discharged states.     

Investigation of Mg modified mesoporous silicas and their CO2 adsorption capacities

CO₂ adsorption properties on Mg modified silica mesoporous materials were investigated. By using the methods of co-condensation, dispersion and ion-exchange, Mg²⁺ was introduced into SBA-15 and MCM-41, and transformed into MgO in the calcination process. The basic MgO can provide active sites to enhance the acidic CO₂ adsorption capacity. To improve the amount and the dispersion state of the loading MgO, the optimized modification conditions were also investigated. The XRD and TEM characteristic results, as well as the CO₂ adsorption performance showed that the CO₂ adsorption capacity not only depended on the pore structures of MCM-41 and SBA-15, but also on the improvement of the dispersion state of MgO by modification. Among various Mg modified silica mesoporous materials, the CO₂ adsorption capacity increased from 0.42 mmol g⁻¹ of pure silica SBA-15 to 1.35 mmol g⁻¹ of Mg–Al–SBA-15-I1 by the ion-exchange method enhanced with Al³⁺ synergism. Moreover, it also increased from 0.67 mmol g⁻¹ of pure silica MCM-41 to 1.32 mmol g⁻¹ of Mg–EDA–MCM-41-D10 by the dispersion method enhanced with the incorporation of ethane diamine. The stability test by 10 CO₂ adsorption/desorption cycles showed Mg–urea–MCM-41-D10 possessed quite good recyclability.     

Mesoporous organo-silica nanoarray for energy storage media

A SnO₂–mesoporous organo-silica nanoarray (MOSN) composite was prepared by surfactant mediated synthesis combined with a sol–gel vacuum suction method in which SnO₂ has been successfully incorporated inside the periodic nanoholes in the MOSN or coated on its surface. The MOSN with a high aspect ratio of length to width could not only maintain its structure but also effectively accommodate the volume expansion of the SnO₂ during electrochemical reactions with Li⁺. The SnO₂–MOSN composite showed a higher reversible capacity of 420 mA h g⁻¹ with greatly improved capacity retention and lower initial irreversible capacity compared to SnO₂ powder. This interesting anodic performance of SnO₂–MOSN composite supports the potential use of MOSN for lithium ion batteries.     

Anatase TiO2 nanosheet: An ideal host structure for fast and efficient lithium insertion/extraction

Anatase TiO₂ nanosheets with largely exposed (0 0 1) facets have been synthesized by a modified method. Exploitation of these nanosheets as a host structure for reversible lithium insertion/extraction has been investigated. It is found that these TiO₂ nanosheets manifest much lower initial irreversible losses compared to other anatase TiO₂ nanostructures, and excellent cycling performance at a charge–discharge rate as high as 20 C. The superior reversible lithium storage capability can be attributed to the ultrathin nanosheet structure: a large exposed effective area and a very short diffusion path. It thus attests the promising use of these anatase TiO₂ nanosheets in high-power lithium–ion batteries.     

Thermodynamic properties of calcium titanates: CaTiO3, Ca4Ti3O10, and Ca3Ti2O7

The chemical potentials of CaO in two-phase fields (TiO₂ + CaTiO₃), (CaTiO₃ + Ca₄Ti₃O₁₀), and (Ca₄Ti₃O₁₀ + Ca₃Ti₂O₇) of the pseudo-binary system (CaO + TiO₂) have been measured in the temperature range (900 to 1250) K, relative to pure CaO as the reference state, using solid-state galvanic cells incorporating single crystal CaF₂ as the solid electrolyte. The cells were operated under pure oxygen at ambient pressure. The standard Gibbs free energies of formation of calcium titanates, CaTiO₃, Ca₄Ti₃O₁₀, and Ca₃Ti₂O₇, from their component binary oxides were derived from the reversible e.m.f.s. The results can be summarised by the following equations: CaO(solid) + TiO₂(solid) → CaTiO₃(solid), ΔG° ± 85/(J · mol^?1) = ?80,140 ? 6.302(T/K); 4CaO(solid) + 3TiO₂(solid) → Ca₄Ti₃O₁₀(solid), ΔG° ± 275/(J · mol^?1) = ?243,473 ? 25.758(T/K); 3CaO(solid) + 2TiO₂(solid) → Ca₃Ti₂O₇(solid), ΔG° ± 185/(J · mol^?1) = ?164,217 ? 16.838(T/K).The reference state for solid TiO₂ is the rutile form. The results of this study are in good agreement with thermodynamic data for CaTiO₃ reported in the literature. For Ca₄Ti₃O₁₀ Gibbs free energy of formation obtained in this study differs significantly from that reported by Taylor and Schmalzried at T = 873 K. For Ca₃Ti₂O₇ experimental measurements are not available in the literature for direct comparison with the results obtained in this study. Nevertheless, the standard entropy for Ca₃Ti₂O₇ at T = 298.15 K estimated from the results of this study using the Neumann–Koop rule is in fair agreement with the value obtained from low-temperature heat capacity measurements.