Influence of temperature on a carbon–fibre epoxy composite subjected to static and fatigue loading under mode-I delamination

In this paper, interlaminar crack initiation and propagation under mode-I with static and fatigue loading of a composite material are experimentally assessed for different test temperatures. The material under study is made of a 3501-6 epoxy matrix reinforced with AS4 unidirectional carbon fibres, with a symmetric laminate configuration [0°]_16/S. In the experimental programme, DCB specimens were tested under static and fatigue loading. Based on the results obtained from static tests, fatigue tests were programmed to analyse the mode-I fatigue behaviour, so the necessary number of cycles was calculated for initiation and propagation of the crack at the different temperatures. G–N curves were determined under fatigue loading, N being the number of cycles at which delamination begins for a given energy release rate. G_ICmax–a, a–N and da/dN–a curves were also determined for different G_cr rates (90%, 85%, 75%, etc.) and different test temperatures: 90 °C, 50 °C, 20 °C, 0 °C, ?30 °C and ?60 °C.     

Theoretical stress analysis of intersecting cylindrical shells subjected to external loads transmitted through branch pipes

A thin shell theoretical solution of two normally intersecting cylindrical shells subjected to thrust-out force and three kinds of moments transmitted through branch pipes is presented in this paper. The solutions of modified Morley equation, which can be applicable up to ρ₀ = d/D ⩽ 0.8 and λ = d/(DT)^1/2 ⩽ 8 and the order of accuracy is raised to O(T/D), for the four loading cases are given. The accurate continuity conditions of generalized forces and displacements at the intersecting curve of two cylindrical shells for the four loading cases and the condition of the uniqueness of displacements are derived in this paper. The presented results are verified by experimental and numerical results successfully. They are in agreement with WRC Bulletin 297 when d/D is small.     

Computational and experimental characterization of a liquid jet plunging into a quiescent pool at shallow inclination

A circular water jet (Re = 1.6 × 10⁵; We = 8.8 × 10³) plunging at shallow angles (θ ≈ 12.5°) into a quiescent pool is investigated computationally and experimentally. A surprising finding from the work is that cavities, of the order of jet diameter, are formed periodically in the impact location, even though the impinging flow is smooth and completely devoid of such a periodicity. Computational prediction of these frequencies was compared with experimental findings, yielding excellent agreement. The region in the vicinity of the impact is characterized by strong churning due to splashing and formation of air cavities. Measured velocity profiles indicate a concentration of momentum beneath the free surface slightly beyond the impact location (X/D_j ≈ 14), with a subsequent shift towards the free surface further downstream of this point (X/D_j ≈ 30). This shift is due primarily to the action of buoyancy on the cavity/bubble population. Comparisons of the mean velocity profile between simulations and experiments are performed, yielding good agreement, with the exception of the relatively small churning flow region. Further downstream (X/D_j ≳ 40), the flow develops mostly due to diffusion and the location of peak velocity coincides with the free surface. In this region, the free surface acts as an adiabatic boundary and restricts momentum diffusion, causing the peak velocity to occur at the free surface.     

Revisiting the perforation of ductile plates by sharp-nosed rigid projectiles

The process of ductile plate perforation by sharp-nosed rigid projectiles is further examined in this work through 2D numerical simulations. We highlight various features concerning the effective resisting stress (σ_r) which a finite thickness plate, with a flow stress of Y_t, exerts on the projectile during perforation. In particular, we show that the normalized resisting stress (σ_r/Y_t) can be represented as a unique function of the normalized thickness of the plate (H/D, where H is plate thickness and D is projectile diameter), for a large range of normalized thicknesses. Our simulations for very thin target plates show that the penetration process is achieved through the well-known dishing mechanism, where the target material is pushed forward by the projectile’s nose. An important observation, which emerges from our simulations, is that the transition between the dishing and the hole enlargement mechanisms takes place at a normalized thickness of about H/D = 1/3. We also find that the normalized resistive stress for intermediate plate thicknesses, 1/3 < H/D < 1.0, is relatively constant at a value of σ_r/Y_t = 2.0. This range of thicknesses conforms to a state of quasi plane stress in the plates. For thicker plates (H/D > 1) the σ_r/Y_t ratio increases monotonically to values which represent the resistance to penetration of semi-infinite targets, where the stress state is characterized by plane strain conditions. Using a simple model, which is based on energy conservation, we can predict the values of the ballistic limit velocities for many projectile/target combinations, provided the perforation is done through the ductile hole enlargement mechanism. Good agreement is demonstrated between predictions from our model and experimental data from different sources, strongly enhancing the confidence in both the validity and usefulness of our model.     

Preparation of 3D micro/nanostructured CeO2: Influence of organic/inorganic acids

CeO₂ is an important porous material with a wide range of applications in the abatement of volatile organic compounds (VOCs). In this paper, we prepared a series of novel three-dimensional (3D) micro/nanostructured CeO₂ materials via a solvothermal method. Organic acid-assisted synthesis and inorganic acid post-treatment were used to adjust the CeO₂ microstructures. The size of the 3D micro/nanostructures could be controlled in the range from 180 nm to 1.5 μm and the surface morphology changed from rough to smooth with the use of different organic acids. The CeO₂ synthesized with acetic acid featured a hierarchical porosity and showed good performance for toluene catalytic combustion: a T₅₀ of 187 °C and a T₉₀ of 195 °C. Moreover, the crystallite size, textural properties, and surface chemical states could be tuned by inorganic acid modification. After treatment with HNO₃, the modified CeO₂ materials exhibited improved catalytic activity, with a T₅₀ of ∼175 °C and a T₉₀ of ∼187 °C. We concluded that the toluene combustion activity is related to the porosity and the amount of surface active oxygen of the CeO₂. Both these features can be tuned by the co-work of organic and inorganic acids.     

Influence of single rectangular groove on the flow past a circular cylinder

In the present study, flow control mechanism of single groove on a circular cylinder surface is presented experimentally using Particle image velocimetry (PIV). A square shaped groove is patterned longitudinally on the surface of the cylinder with a diameter of 50 mm. The flow characteristics are studied as a function of angular position of the groove from the forward stagnation point of the cylinder within 0° ≤ θ ≤ 150°. In the current work, instantaneous and time-averaged flow data such as vorticity, ω streamline, Ψ streamwise, u/U_o and transverse, v/U_o velocity components, turbulent kinetic energy, TKE and RMS of streamwise, u_rms and transverse, v_rms velocity components are utilized in order to present the results of quantitative analyses. Furthermore, Strouhal numbers are calculated using Karman vortex shedding frequency, f_k obtained from single point spectral analysis. It is concluded that a critical angular position of the groove, θ = 80° is observed. The flow separation is controlled within 0° ≤ θ < 80°. At θ = 80°, the flow separation starts to occur in the upstream direction. The instability within the shear layer is also induced on grooved side of the cylinder with frequencies different than Karman vortex shedding frequency, f_k.     

Turbulent channel flow of dilute polymeric solutions: Drag reduction scaling and an eddy viscosity model

Direct numerical simulation of viscoelastic turbulent channel flows up to the maximum drag reduction (MDR) limit has been performed. The simulation results in turn have been used to develop relationships between the flow and fluid rheological parameters, i.e. maximum chain extensibility, Reynolds number, Re_τ, and Weissenberg number, We_τ and percent drag reduction (%DR) as well as the slope increment of the mean velocity profile. Moreover, based on the trends observed in the mean velocity profile and the overall momentum balance three different regimes of drag reduction (DR), namely, low drag reduction (LDR; 0 ≤ %DR ≤ 20), high drag reduction (HDR; 20 ≤ %DR ≤ 52) and MDR (52 ≤ %DR ≤ 74) have been identified and mathematical expressions for the eddy viscosity in these regimes are presented. It is found that both in LDR and HDR regimes the eddy viscosity varies with the distance from the channel wall. However, in the MDR regime the ratio of the eddy viscosity to the Newtonian one tends to a very small value around 0.1 within the channel. Based on these expressions a procedure that relies on the DNS predictions of the budgets of momentum and viscoelastic shear stress is developed for evaluating the mean velocity profile.     

Surface responses induced by point load or uniform traction moving steadily on an anisotropic half-plane

Surface responses induced by point load or uniform traction moving steadily with subsonic speed on an anisotropic half-plane boundary are investigated. It is found that the effects of the material constant on surface displacements are through matrices L^?1(v) and S(v)L^?1(v), while those on surface stress components are through matrices Ω(v) and Γ(v). Explicit expressions for the elements of these four matrices are expressed in terms of elastic stiffness for general anisotropic materials. The special cases of monoclinic materials with symmetry plane at x₁ = 0, x₂ = 0 and x₃ = 0, and the case for orthotropic materials are all deduced. Results for isotropic material may be recovered from present results. For monoclinic materials with a plane of symmetry at x₃ = 0, two of the elements of matrix Ω(v) are found to be independent of subsonic speed.     

Continuum interpretation of virial stress in molecular simulations

The equivalence of the virial stress and Cauchy stress is reviewed using both theoretical arguments and numerical simulations. Using thermoelasticity problems as examples, we numerically demonstrate that virial stress is equivalent to the continuum Cauchy stress. Neglecting the velocity terms in the definition of virial stress as many authors have recently suggested, can cause significant errors in interpreting MD simulation results at elevated temperatures (T > 0 K).     

Effects of rotation on flow in an asymmetric rib-roughened duct: LES study

We report on large-eddy simulations (LES) of fully-developed asymmetric flow in a duct of a rectangular cross-section in which square-sectioned, equally-spaced ribs oriented perpendicular to the flow direction, were mounted on one of the walls. The configuration mimics a passage of internal cooling of a gas-turbine blade. The duct flow at a Reynolds number Re = 15,000 (based on hydraulic diameter D_h and bulk flow velocity U₀) was subjected to clock-wise (stabilising) and anti-clock-wise (destabilising) orthogonal rotation at a moderate rotational number Ro = ΩD_h/U₀ = 0.3, where Ω is the angular velocity. The LES results reproduced well the available experimental results of Coletti et al. (2011) (in the mid-plane adjacent to the ribbed wall) and provided insight into the whole duct complementing the reference PIV measurement. We analyzed the effects of stabilising and destabilising rotation on the flow, vortical structures and turbulence statistics by comparison with the non-rotating case. The analysis includes the identification of depth of penetration of the rib-effects into the bulk flow, influence of flow three-dimensionality and the role of secondary motions, all shown to be strongly affected by the rotation and its direction.     

Flow evolution of a turbulent submerged two-dimensional rectangular free jet of air. Average Particle Image Velocimetry (PIV) visualizations and measurements

The paper presents average flow visualizations and measurements, obtained with the Particle Image Velocimetry (PIV) technique, of a submerged rectangular free jet of air in the range of Reynolds numbers from Re = 35,300 to Re = 2200, where the Reynolds number is defined according to the hydraulic diameter of a rectangular slot of height H. According to the literature, just after the exit of the jet there is a zone of flow, called zone of flow establishment, containing the region of mixing fluid, at the border with the stagnant fluid, and the potential core, where velocity on the centerline maintains a value almost equal to the exit one. After this zone is present the zone of established flow or fully developed region. The goal of the paper is to show, with average PIV visualizations and measurements, that, before the zone of flow establishment is present a region of flow, never mentioned by the literature and called undisturbed region of flow, with a length, L_U, which decreases with the increase of the Reynolds number. The main characteristics of the undisturbed region is the fact that the velocity profile maintains almost equal to the exit one, and can also be identified by a constant height of the average PIV visualizations, with length, L_CH, or by a constant turbulence on the centerline, with length L_CT. The average PIV velocity and turbulence measurements are compared to those performed with the Hot Film Anemometry (HFA) technique. The average PIV visualizations show that the region of constant height has a length L_CH which increases from L_CH = H at Re = 35,300 to L_CH = 4–5H at Re = 2200. The PIV measurements on the centerline of the jet show that turbulence remains constant at the level of the exit for a length, L_CT, which increases from L_CT = H at Re = 35,300 to L_CT = 4–5H at Re = 2200. The PIV measurements show that velocity remains constant at the exit level for a length, L_U, which increases from L_U = H at Re = 35,300 to L_U = 6H at Re = 2200 and is called undisturbed region of flow. In turbulent flow the length L_U is almost equal to the lengths of the regions of constant height, L_CH, and constant turbulence, L_CT. In laminar flow, Re = 2200, the length of the undisturbed region of flow, L_U, is greater than the lengths of the regions of constant height and turbulence, L_CT = L_CH = 4–5H. The average PIV and HFA velocity measurements confirm that the length of potential core, L_P, increases from L_P = 4–5H at Re = 35,300 to L_P = 7–8H at Re = 2200, and are compared to the previous experimental and theoretical results of the literature in the zone of mixing fluid and in the fully developed region with a good agreement.     

Study of material agglomeration during nozzle injection of multiviscosity liquid into a fluidized bed reactor by the electric conductance method

Fluidized bed agglomeration is an important and challenging problem for thermal cracking in fluid cokers. A low coker temperature can be problematic because the bitumen is injected into the fluidized bed with a different viscosity, resulting in formation of agglomerates of varying sizes, which slows the cracking reactions. In the present study, the bed material agglomeration process during nozzle injection of multiviscosity liquid was investigated in a fluidized bed operated at different mass ratios of the atomization gas to the liquid jets (GLR = 1%–3.5%) and gas velocities (3.9U_mf and 5.9U_mf) based on a conductance method using a water–sand system to simulate the hot bitumen–coke system at room temperature. During the tests of liquid-jet dispersion throughout the bed, different agglomeration stages are observed at both gas velocities. The critical amount of tert-butanol in the liquid jets that could lead to severe agglomeration of the bed materials (poor fluidization) at GLR = 1% is about 10 wt% at the low fluidizing gas velocity (3.9U_mf) and 18 wt% at the high gas velocity (5.9U_mf). This study provides a new approach for on-line monitoring of bed agglomeration during liquid injection to guarantee perfect contact between the atomized liquid and the bed particles.     

Flow boiling heat transfer of R134a,R236fa and R245fa in a horizontal 1.030 mm circular channel

This research focuses on acquiring accurate flow boiling heat transfer data and flow pattern visualization for three refrigerants, R134a, R236fa and R245fa in a 1.030 mm channel. We investigate trends in the data, and their possible mechanisms, for mass fluxes from 200 to 1600 kg/m²s, heat fluxes from 2.3 kW/m² to 250 kW/m² at T_sat = 31 °C and ΔT_sub from 2 to 9 K. The local saturated flow boiling heat transfer coefficients display a heat flux and a mass flux dependency but no residual subcooling influence. The changes in heat transfer trends correspond well with flow regime transitions. These were segregated into the isolated bubble (IB) regime, the coalescing bubble (CB) regime, and the annular (A) regime for the three fluids. The importance of nucleate boiling and forced convection in these small channels is still relatively unclear and requires further research.     

Turbulent boundary layers over sparsely-spaced rod-roughened walls

Direct numerical simulations (DNSs) of spatially developing turbulent boundary layers (TBLs) over sparsely-spaced two-dimensional (2D) rod-roughened walls were performed. The rod elements were periodically arranged along the streamwise direction with pitches of p_x/k = 8, 16, 32, 64 and 128, where p_x is the streamwise spacing of the rods, and k is the roughness height. The Reynolds number based on the momentum thickness was varied from Re_θ = 300–1400, and the height of the roughness element was k = 1.5θ_in, where θ_in is the momentum thickness at the inlet. The characteristics of the TBLs, such as the friction velocity, mean velocity, and Reynolds stresses over the rod-roughened walls, were examined by varying the spacing of the roughness features (8 ⩽ p_x/k ⩽ 128). The outer-layer similarity between the rough and smooth walls was established for the sparsely-distributed rough walls (p_x/k ⩾ 32) based on the profiles of the Reynolds stresses, whereas those are not for p_x/k = 8 and 16. Inspection of the interaction between outer-layer large-scale motions and near-wall small-scale motions using two-point amplitude modulation (AM) covariance showed that modulation effect of large-scale motions on near-wall small-scale motions was strongly disturbed over the rough wall for p_x/k = 8 and 16. For p_x/k ⩾ 32, the flow that passed through the upstream roughness element transitioned to a smooth wall flow between the consecutive rods. The strong influence of the surface roughness in the outer layer for p_x/k = 8 and 16 was attributed to large-scale erupting motions by the surface roughness, creating both upward shift of the near-wall turbulent energy and active energy production in the outer layer with little influence on the near-wall region.     

Some exact solutions for rotating flows of a generalized Burgers’ fluid in cylindrical domains

The velocity field and the adequate shear stress corresponding to the flow of a generalized Burgers’ fluid model, between two infinite co-axial cylinders, are determined by means of Laplace and finite Hankel transforms. The motion is due to the inner cylinder that applies a time dependent torsional shear to the fluid. The solutions that have been obtained, presented in series form in terms of usual Bessel functions J₁( ? ), J₂( ? ), Y₁( ? ) and Y₂( ? ), satisfy all imposed initial and boundary conditions. Moreover, the corresponding solutions for Burgers’, Oldroyd-B, Maxwell, second grade, Newtonian fluids and large-time transient solutions for generalized Burgers’ fluid are also obtained as special cases of the present general solutions. The effect of various parameters on large-time and transient solutions of generalized Burgers’ fluid is also discussed. Furthermore, for small values of the material parameters, λ₂ and λ₄ or λ₁, λ₂, λ₃ and λ₄, the general solutions corresponding to generalized Burgers’ fluids are going to those for Oldroyd-B and Newtonian fluids, respectively. Finally, the influence of the pertinent parameters on the fluid motion, as well as a comparison between models, is shown by graphical illustrations.     

The effect of incidence angle on the mean wake of surface-mounted finite-height square prisms

The mean wake of a surface-mounted finite-height square prism was studied experimentally in a low-speed wind tunnel to explore the combined effects of incidence angle (α) and aspect ratio (AR). Measurements of the mean wake velocity field were made with a seven-hole pressure probe for finite square prisms of AR = 9, 7, 5 and 3, at a Reynolds number of Re = 3.7 × 10⁴, for incidence angles from α = 0° to 45°. The relative thickness of the boundary layer on the ground plane, compared to the prism width, was δ/D = 1.5. As the incidence angle increases from α = 0° to 15°, the mean recirculation zone shortens and the mean wake shifts in the direction opposite to that of the mean lift force. The downwash is also deflected to this side of the wake and the mean streamwise vortex structures in the upper part of the wake become strongly asymmetric. The shortest mean recirculation zone, and the greatest asymmetry in the mean wake, is found at the critical incidence angle of α_critical ≈ 15°. As the incidence angle increases from α = 15° to 45°, the mean recirculation zone lengthens and the mean streamwise vortex structures regain their symmetry. These vortices also elongate in the wall-normal direction and become contiguous with the horseshoe vortex trailing arms. The mean wake of the prism of AR = 3 has some differences, such as an absence of induced streamwise vorticity near the ground plane, which support its classification as lying below the critical aspect ratio for the present flow conditions.     

CFD modelling and wind tunnel validation of airflow through plant canopies using 3D canopy architecture

The efficiency of pesticide application to agricultural fields and the resulting environmental contamination highly depend on atmospheric airflow. A computational fluid dynamics (CFD) modelling of airflow within plant canopies using 3D canopy architecture was developed to understand the effect of the canopy to airflow. The model average air velocity was validated using experimental results in a wind tunnel with two artificial model trees of 24 cm height. Mean air velocities and their root mean square (RMS) values were measured on a vertical plane upstream and downstream sides of the trees in the tunnel using 2D hotwire anemometer after imposing a uniform air velocity of 10 m s^?1 at the inlet. 3D virtual canopy geometries of the artificial trees were modelled and introduced into a computational fluid domain whereby airflow through the trees was simulated using Reynolds-Averaged Navier–Stokes (RANS) equations and k-ε turbulence model. There was good agreement of the average longitudinal velocity, U between the measurements and the simulation results with relative errors less than 2% for upstream and 8% for downstream sides of the trees. The accuracy of the model prediction for turbulence kinetic energy k and turbulence intensity I was acceptable within the tree height when using a roughness length (y₀ = 0.02 mm) for the surface roughness of the tree branches and by applying a source model in a porous sub-domain created around the trees. The approach was applied for full scale orchard trees in the atmospheric boundary layer (ABL) and was compared with previous approaches and works. The simulation in the ABL was made using two groups of full scale orchard trees; short (h = 3 m) with wider branching and long (h = 4 m) with narrow branching. This comparison showed good qualitative agreements on the vertical profiles of U with small local differences as expected due to the spatial disparities in tree architecture. This work was able to show airflow within and above the canopy in 3D in more details.