Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Preparation of Thermosensitive Hollow Imprinted Microspheres via Combining Distillation Precipitation Polymerization and Thiol‐ene Click Chemistry

Hollow molecular imprinted polymer microspheres were prepared by distillation precipitation polymerization with (S)‐(+)‐ibuprofen (S‐IBF) as template molecule and acrylamide (AM) as functional monomer. Using the silicon dioxide (SiO₂, 180 nm) modified by 3‐(trimethoxysilyl)propyl methacrylate (MPS) as the template microspheres, the molecular imprinted shells were coated on successfully (SiO₂@MIPs). The thermosensitive SiO₂@MIPs‐PNIPAM core‐shell microspheres were subsequently prepared by grafting the PNIPAM chains (M_n=1.21×10⁴ g/mol, polydispersity index=1.30), which were prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization, on the surface of SiO₂@MIPs microspheres via the thiol‐ene click chemistry. The grafting density of PNIPAM brushes on the SiO₂@MIPs microspheres was about 0.18 chains/nm². After HF etching, the hollow imprinted microspheres were finally obtained. For thermosensitivity analysis, the phase transition temperatures of multifunctional nanoparticles were measured by DSL at 25°C and 45°C respectively, and the sizes of the microspheres changed by about 35 nm. The modified microspheres presented excellent controlled release property to S‐IBF, moreover about half amount of the adsorptions passed into acetonitrile‐water solution through the specific holes of imprinted shell at 25°C under vibration.     

Synthesis and characterization of pH‐sensitive and thermosensitive double hydrophilic graft copolymers

A series of poly(N‐isopropylacrylamide)‐co‐poly(N^ε‐benzyloxycarbonyl‐L ‐lysine) graft copolymers (PNIPAm‐co‐PZLLys) with different side chains (degree of polymerization, DP = 5～40) and unit ratios (from 30 to 70 mol %) were prepared via free radical polymerization, followed by cleaving benzyloxycarbonyl groups (Z groups) to obtain the double hydrophilic graft copolymer, poly(N‐isopropylacrylamide)‐co‐poly(L ‐lysine) (PNIPAm‐co‐PLLys). The pH‐ and temperature‐response properties of the graft copolymers in aqueous solution were studied. The experimental results indicate L15‐N30 and L15N‐70, that is, the PNIPAm‐co‐PLLys having the poly(L ‐lysine) of DP = 15 as side chains as well as 30 and 70 mol %, respectively, of PNIPAm as backbone, have coil‐to‐helix transitions from pH 6 to pH 12 at room temperature and form uniform nanoscale micelle‐like dispersions in aqueous solution at pH 12. The graft copolymers also could form uniform and nanoscale micelle‐like structures at 50 °C in pH 6 buffer solution due to slightly polymer aggregation. With temperature and pH increased, both the deprotonated PLLys side chains and PNIPAm backbone become hydrophobic, leading to polymer precipitation. These results illustrate that a double tunable hydrophilic graft copolymer had been successfully synthesized via a simple radical polymerization, and could form micelles without serious polymer aggregation at a lower pH and a higher temperature. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Surface‐initiated single‐electron transfer reversible addition–fragmentation chain transfer polymerization of 2‐hydroxyethyl acrylamide on silicon substrate at ambient temperature

2‐Hydroxyethyl acrylamide was successfully polymerized via single‐electron transfer initiation on the silicon surface and propagation through the reversible addition–fragmentation chain transfer (SET‐RAFT) polymerization at ambient temperature for different polymerization times. This work is the first time application of the surface‐initiated SET‐RAFT mechanism to afford the preparation of well‐defined poly(2‐hydroxyethyl acrylamide) [poly(HEAAm)] brushes at ambient temperature. The polymerization was well controlled and produced poly(HEAAm) brushes on the silicon surface with a well‐defined target molecular weight. The controlled nature of the polymerization was further demonstrated in the presence of sulfur atoms at the chain ends in X‐ray photoelectron spectroscopy experiments. The grafting density (σ, chains nm^?2) and the average distance between grafting points (D, nm) were found to be 0.42 chains nm^?2 and 1.74 nm, respectively, indicating moderate grafting density. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1140–1146     

Synthesis of dual‐functional poly(6‐azidohexylmethacrylate) brushes by a RAFT agent carrying carboxylic acid end groups

Novel types of dual‐functional surface‐attached polymer brushes were developed by interface‐mediated reversible addition‐fragmentation chain transfer (RAFT) polymerization of 6‐azidohexylmethacrylate using the surface‐immobilized RAFT agent and the free initiator. The interface‐mediated RAFT polymerization produced silicon substrate coated with dual‐functional (azido groups from monomer and carboxylic acid groups from RAFT agent) poly(6‐azidohexylmethacrylate) [poly (AHMA)] with a grafting density as high as 0.59 chains/nm². Dual‐functional polymer brushes can represent an attractive chemical platform to deliberately introduce other molecular units at specific sites. The azido groups of the poly(AHMA) brushes can be modified with alkyl groups via click reaction, known for their DNA hybridization, while the carboxylic acid end groups can be reacted with amine groups via amide reaction, known for their antifouling properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1696–1706     

Silica/poly (N‐vinylimidazolium) nanospheres by combined RAFT polymerization and thiol‐ene click chemistry

We report a facile method that combined sol–gel reaction, reversible addition–fragmentation chain transfer (RAFT)/macromolecular design via interchange of the xanthates process and thiol‐ene click reaction to prepare monodisperse silica core‐poly(N‐vinylimidazole) (PVim) shell microspheres of 200 nm in average diameters. First, silica with C = C double bonds was prepared by the sol–gel reaction of 3‐(trimethoxysilyl)propyl methacrylates (MPS) with tetraethoxysilane in ethanol; SiO₂@PVim were subsequently prepared by grafting PVim chain (Mn = 9800 g/mol, polydispersity index = 1.22) to MPS‐SiO₂ via the thiol‐ene click chemisty. The obtained SiO₂@PVim microspheres show higher catalytic activity toward the hydrolysis of p‐nitrophenyl acetate compared with the PVim homopolymers. The as‐prepared composites have been characterized by scanning electron microscopy, transmission electron microscopy, thermal gravimetric analysis and Fourier transform infrared spectrometry analysis. Copyright © 2014 John Wiley & Sons, Ltd.     

High density cationic polymer brushes from combined “click chemistry” and RAFT‐mediated polymerization

A simple method for preparing cationic poly[(ar‐vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was used by combined technology of “click chemistry” and reversible addition‐fragmentation chain transfer (RAFT) polymerization. Initially, silicon surfaces were modified with RAFT chain transfer agent by using a click reaction involving an azide‐modified silicon wafer and alkyne‐terminated 4‐cyanopentanoic acid dithiobenzoate (CPAD). A series of poly(VBTAC) brushes on silicon surface with different molecular weights, thicknesses, and grafting densities were then synthesized by RAFT‐mediated polymerization from the surface immobilized CPAD. The immobilization of CPAD on the silicon wafer and the subsequent polymer formation were characterized by X‐ray photoelectron spectroscopy, water contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and ellipsometry analysis. The addition of free CPAD was required for the formation of well‐defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. In addition, by varying the polymerization time, we were able to obtain poly(VBTAC) brushes with grafting density up to 0.78 chains/nm² with homogeneous distributions of apparent needle‐like structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Uni‐molecular nanoparticles of poly(2‐oxazoline) showing tunable thermoresponsive behaviors

Herein, cylindrical molecular bottlebrushes grafted with poly(2‐oxazoline) (POx) as a shaped tunable uni‐molecular nanoparticle were synthesized via the grafting‐onto approach. First, poly(glycidyl methacrylate) (PGMA) backbones with azide pendant units were prepared via reversible addition fragmentation transfer (RAFT) polymerization followed by post‐modification. The degree of polymerization (DP) of the backbones was tuned in a range from 20 to 800. Alkynyl‐terminated POx side chains were synthesized by living cationic ring opening polymerization (LCROP) of 2‐ethyl‐2‐oxazoline (EtOx) and 2‐methyl‐2‐oxazoline (MeOx), respectively. The DP of side chains was varied between 20 and 100. Then, the copper‐catalyzed azide‐alkynyl cycloaddition (CuAAC) click chemistry was conducted with a feed ratio of [alkynyl]:[azide] = 1.2:1 to yield a series of brushes. Depending on the DP of side chains, the grafting density ranged between 47 and 85%. The resulting brushlike nanoparticles exhibited shapes of sphere, rod and worm. Aqueous solutions of PEtOx brushes demonstrated a thermoresponsive behavior as a function of the length of backbones and side chains. Surprisingly, it was found that the lower critical solution temperature of PEtOx brushes increased with a length increase of backbones. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 174–183     

Macromolecular brushes synthesized by “grafting from” approach based on “click chemistry” and RAFT polymerization

Well‐defined macromolecular brushes with poly(N‐isopropyl acrylamide) (PNIPAM) side chains on random copolymer backbones were synthesized by “grafting from” approach based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization. To prepare macromolecular brushes, two linear random copolymers of 2‐(trimethylsilyloxy)ethyl methacrylate (HEMA‐TMS) and methyl methacrylate (MMA) (poly(MMA‐co‐HEMA‐TMS)) were synthesized by atom transfer radical polymerization and were subsequently derivated to azide‐containing polymers. Novel alkyne‐terminated RAFT chain transfer agent (CTA) was grafted to polymer backbones by copper‐catalyzed 1,3‐dipolar cycloaddition (azide‐alkyne click chemistry), and macro‐RAFT CTAs were obtained. PNIPAM side chains were prepared by RAFT polymerization. The macromolecular brushes have well‐defined structures, controlled molecular weights, and molecular weight distributions (M_w/M_n ≦ 1.23). The RAFT polymerization of NIPAM exhibited pseudo‐first‐order kinetics and a linear molecular weight dependence on monomer conversion, and no detectable termination was observed in the polymerization. The macromolecular brushes can self‐assemble into micelles in aqueous solution. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 443–453, 2010     

Fast fabrication of a hybrid monolithic column containing cyclic and aliphatic hydrophobic ligands via photo‐initiated thiol‐ene polymerization

Three monomers, octakis (3‐mercaptopropyl) octasilsesquioxane, 1,2,4‐trivinylcyclohexane and isophytol were employed to synthesize a novel monolithic stationary phase via photo‐initiated thiol‐ene click polymerization for reversed‐phase liquid chromatography. Several factors such as porogenic system, reaction time and the molar ratio of functional groups were investigated in detail. The resulting poly(POSS‐co‐TVCH‐co‐isophytol) monolithic column exhibited suitable permeability for fast separation and outstanding thermal stability. Five alkylbenzenes were employed to evaluate the ability of chromatographic separation of the resulting monolithic columns at different flow rates, and showed the highest column efficiencies of 90,200–93,100 N/m (corresponding to 10.4–10.6 μm of plate height) at a velocity of 0.41 mm/s. The baseline separations of five anilines and eight phenols further proved the applicability of poly(POSS‐co‐TVCH‐co‐isophytol) monolithic column in the separation of small molecules.     

Facile synthesis and responsive behavior of PDMS‐b‐PEG diblock copolymer brushes via photoinitiated “thiol‐ene” click reaction

We present herein a mild and rapid method to create diblock copolymer brushes on a silicon surface via photoinitiated “thiol‐ene” click reaction. The silicon surface was modified with 3‐mercaptopropyltrimethoxysilane (MPTMS) self‐assembled monolayer. Then, a mixture of divinyl‐terminated polydimethylsiloxane (PDMS) and photoinitiator was spin‐coated on the MPTMS surface and exposed to UV‐light. Thereafter, a mixture of thiol‐terminated polyethylene glycol (PEG) and photoinitiator were spin‐coated on the vinyl‐terminated PDMS‐treated surface, and the sequent photopolymerization was carried out under UV‐irradiation. The MPTMS, PDMS, and PEG layers were carefully identified by X‐ray photoelectron spectroscopy, atomic force microscopy, ellipsometry, and water contact angle measurements. The thickness of the polydimethylsiloxane‐block‐poly(ethylene glycol) (PDMS‐b‐PEG) diblock copolymer brush could be controlled by the irradiation time. The responsive behavior of diblock copolymer brushes treated in different solvents was also discussed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characteristics of poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive semi‐hollow latex particles and their application to drug carriers

In this work, the poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite semi‐hollow latex particles was synthesized by three processes. The first process was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly (MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second process was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and crosslinking agent, N,N′‐methylenebisacrylamide, in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles with solid structure. In the third process, part of the linear poly(MMA‐MAA) core of core–shell latex particles was dissolved by ammonia to form the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles. The morphologies of the semi‐hollow latex particles show that there is a hollow zone between the linear poly(MMA‐MAA) core and the crosslinked poly(MAA‐NIPAAm) shell. The crosslinking agent and shell composition significantly influenced the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) semi‐hollow latex particles. Besides, the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles were used as carriers to load with the model drug, caffeine. The processes of caffeine loaded into the semi‐hollow latex particles appeared four situations, which was different from that of solid latex particles. In addition, the phenomenon of caffeine released from the semi‐hollow latex particles was obviously different from that of solid latex particles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3441–3451     

Cyclodextrin‐overhanging hyperbranched core‐double‐shell miktoarm architectures: Synthesis and gradient stimuli‐responsive properties

We report the synthesis and gradient stimuli‐responsive properties of cyclodextrin‐overhanging hyperbranched core‐double‐shell miktoarm architectures. A ionic hyperbranched poly(β‐cyclodextrin) (β‐CD) core was firstly synthesized via a convenient “A₂+B₃” approach. Double‐layered shell architectures, composed of poly(N‐isopropyl acrylamide) (PNIPAm) and poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) miktoarms as the outermost shell linked to poly(N,N‐diethylaminoethyl methacrylate) (PDEAEMA) homoarms which form the inner shell, were obtained by a sequential atom transfer radical polymerization (ATRP) and parallel click chemistry from the modified hyperbranched poly(β‐CD) macroinitiator. The combined characterization by ¹H NMR, ¹³C NMR, ¹H‐²⁹Si heteronuclear multiple‐bond correlation (HMBC), FTIR and size exclusion chromatography/multiangle laser light scattering (SEC/MALLS) confirms the remarkable hyperbranched poly(β‐CD) core and double‐shell miktoarm architectures. The gradient triple‐stimuli‐responsive properties of hyperbranched core‐double‐shell miktoarm architectures and the corresponding mechanisms were investigated by UV–vis spectrophotometer and dynamic light scattering (DLS). Results show that this polymer possesses three‐stage phase transition behaviors. The first‐stage phase transition comes from the deprotonation of PDEAEMA segments at pH 9–10 aqueous solution under room temperature. The confined coil‐globule conformation transition of PNIPAm and PDMAEMA arms gives rise to the second‐stage hysteretic cophase transition between 38 and 44 °C at pH 10. The third‐stage phase transition occurs above 44 °C at pH = 10 attributed to the confined secondary conformation transition of partial PDMAEMA segments. This cyclodextrin‐overhanging hyperbranched core‐double‐shell miktoarm architectures are expected to solve the problems of inadequate functionalities from core layer and lacking multiresponsiveness for shell layers existing in the dendritic core‐multishell architectures. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Photo‐initiated thiol–ene “click” hydrogels from RAFT‐synthesized poly(N‐isopropylacrylamide)

Despite the efficiency and robustness of the widely used copper‐catalyzed 1,3‐dipolar cycloaddition reaction, the use of copper as a catalyst is often not attractive, particularly for materials intended for biological systems. The use of photo‐initiated thiol‐ene as an alternative “click” reaction to synthesize “model networks” is investigated here. Poly(N‐isopropylacrylamide) precursors were synthesized by reversible addition fragmentation chain transfer (RAFT) polymerization and were designed to have trithiocarbonate moieties as end groups. This structure design provides opportunity for subsequent end‐group modifications in preparation for thiol‐ene “click.” Two reaction routes have been proposed and studied to yield thiol and ene moieties. The advantages and disadvantages of each reaction path were investigated to propose a simple but efficient route to prepare copper‐free “click” hydrogels. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4626–4636     

Synthesis and characteristics of poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles and their application as drug carriers

In this work, the poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles was synthesized by a three‐step reaction. The first step was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second step was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and N,N′‐methylenebisacrylamide in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles. In the third step, the core–shell latex particles were heated in the presence of ammonia solution to form the crosslinking poly(MAA‐NIPAAm) thermosensitive hollow latex particles. The morphologies of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were observed. The influences of crosslinking agent and shell composition on the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were, respectively, studied. Besides, the poly(MAA‐NIPAAm) thermosensitive hollow latex particles were used as carriers to load with the model drug, caffeine. The effect of various variables on the amount of caffeine loading and the efficiency of caffeine release was investigated. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5203–5214     

Synthesis and functionalization of dendron‐polymer conjugate based hydrogels via sequential thiol‐ene “click” reactions

Fabrication and functionalization of hydrogels from well‐defined dendron‐polymer‐dendron conjugates is accomplished using sequential radical thiol‐ene “click” reactions. The dendron‐polymer conjugates were synthesized using an azide‐alkyne “click” reaction of alkene‐containing polyester dendrons bearing an alkyne group at their focal point with linear poly(ethylene glycol)‐bisazides. Thiol‐ene “click” reaction was used for crosslinking these alkene functionalized dendron‐polymer conjugates using a tetrathiol‐based crosslinker to provide clear and transparent hydrogels. Hydrogels with residual alkene groups at crosslinking sites were obtained by tuning the alkene‐thiol stoichiometry. The residual alkene groups allow efficient postfunctionalization of these hydrogel matrices with thiol‐containing molecules via a subsequent radical thiol‐ene reaction. The photochemical nature of radical thiol‐ene reaction was exploited to fabricate micropatterned hydrogels. Tunability of functionalization of these hydrogels, by varying dendron generation and polymer chain length was demonstrated by conjugation of a thiol‐containing fluorescent dye. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 926–934     

Influence of nitroxide structure on polystyrene brushes “grafted‐from” silicon wafers

Alkoxyamine derivatives based on 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO), N‐tert‐butyl‐N‐(1‐diethylphosphono‐(2,2‐dimethylpropyl)) nitroxide (SG1) and N‐tert‐butyl‐N‐(2‐methyl‐1‐phenylpropyl) nitroxide (TIPNO) containing a C₁₁ hydrophobic spacer and a reactive triethoxysilyl polar head, were synthesized and anchored to silicon wafers by the Langmuir–Blodgett reactive deposition technique at surface pressures ranging from 15 to 32 mN/m. Polystyrene brushes (M_n ～ 8500–66,400 g/mol) were grown from the alkoxyamine functionalized silicon wafers by nitroxide mediated radical polymerization and characterized by ellipsometry and water contact angle measurements. The main parameters influencing the grafting density and the degree of stretching of the brushes are the nitroxide polarity and, therefore, the behavior of the corresponding alkoxyamines at the air/water interface of the Langmuir–Blodgett trough. Depending on the alkoxyamine chemical structure and the surface pressure during Langmuir–Blodgett deposition, polystyrene brushes with grafting densities of 0.3–1.0 chains/nm² and stretching values of 40–70% were obtained. Regarding alkoxyamines deposited at high surface pressures, size exclusion chromatography experiments performed on both cleaved polystyrene brushes and chains simultaneously grown in the bulk revealed that the polymerization degree of the bulk and surface chains are significantly different, suggesting that steric constrains affect the polymerization kinetics occurring at the silicon surface. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3367–3374, 2008     

Smart Surface of Gold Nanoparticles Fabricated by Combination of RAFT and Click Chemistry

A simple efficient post‐modification route to the fabrication of hybrid gold nanoparticles with poly(N‐isopropylacrylamide) (PNIPAm) based on click chemistry is described. The PNIPAm was prepared by reversible addition fragmentation chain transfer radical polymerization (RAFT). The PNIPAm was immobilized onto gold nanoparticles with grafting densities of 5.8 chains · nm⁻² by a click reaction. The hybrid gold nanoparticles showed a temperature responsive phenomenon as the temperature changed between 20 and 45 °C.

     

Magnetic solid-phase extraction using magnetic hypercrosslinked polymer for rapid determination of illegal drugs in urine

A novel magnetic material Fe₃O₄/SiO₂/P(MAA‐co‐VBC‐co‐DVB) was prepared via the hypercrosslinking of its precursor which was produced via precipitation polymerization of methacrylic acid (MAA), vinylbenzyl chloride (VBC), and divinylbenzene (DVB) in the presence of Fe₃O₄/SiO₂ submicrospheres with the surface containing abundant reactive double bonds. The resultant sorbent was characterized by scan electron microscopy, N₂ adsorption, and Fourier transform infrared spectroscopy. It was found that this material had remarkable features such as large surface area (500 m²/g) and pore volume (0.32 cm³/g), as well as desirable chemical composition (including hydrophobic and ion‐exchange moieties). Taking advantages of the Fe₃O₄/SiO₂/P(MAA‐co‐VBC‐co‐DVB), a magnetic SPE (MSPE) coupled with capillary electrophoresis (CE) method was developed for the determination of illegal drugs in urine samples. The extraction time could be clearly shortened up to 3 min. The recoveries of these drug compounds were in the range of 84.0–123% with relative standard deviations ranging between 1.7 and 10.5%; the limit of detection was in the range of 4.0–6.0 μg/L. The proposed method is simple, effective, and low‐cost, and provides an accurate and sensitive detection platform for abused drug analysis.