Synthesis of methallylic monomers bearing ammonium side‐groups and their radical copolymerization with chlorotrifluoroethylene

Methallylic monomers bearing triethyl or 4‐diazabicyclo[2.2.2]octane (DABCO) ammonium side‐groups are prepared and copolymerized with chlorotrifluoroethylene (CTFE). First, three different monomers are synthesized from chloro‐2‐methylprop‐1‐ene or 3‐chloro‐2‐chloromethylprop‐1‐ene in fair to good yields (57–95%). Then, several parameters (initiators, aqueous or solution processes, temperature) of the radical copolymerization of these monomers with chlorotrifluoroethylene are investigated. Various initiators are tested in the presence of ammonium perfluorooctanoate (APFO) as water‐soluble surfactant, and tert‐butyl peroxypivalate/APFO leads to the best results in a mixed solvent (H₂O/CH₃CN/C₄F₅H₅). In all experiments, the radical copolymerization shows that CTFE is more reactive than the methallylic monomer as evidenced by the characterization of poly(CTFE‐co‐M) copolymer by nuclear magnetic resonance spectroscopy and elemental analysis. Thermal degradation of these copolymers by thermogravimetric analyses indicates that the copolymers are stable up to 180 °C without any degradation and have a T_d,10% above 300 °C. Finally, their ionic exchange capacities range between 0.94 and 1.69 meq g^?1. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1721–1729     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Synthesis and characterization of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane: Homo‐ and copolymerization with fluorovinyl monomers

The synthesis of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane (D), its radical homopolymerization, and copolymerization with fluoroolefins are presented. Fluorodioxolane (D) was synthesized through direct fluorination of the corresponding hydrocarbon precursor in a fluorinated solvent by F₂/N₂ gas. It was polymerized in bulk using perfluorodibenzoyl peroxide as the initiator. The resulting homopolymer had a limited solubility in fluorinated solvents, and its glass transition temperature (T_g) was in the range of 180–190 °C. The polymeric films prepared by casting from hot hexafluorobenzene (HFB) solution were transparent with low refractive index (1.329 at 633 nm). These films were thermally stable (T_d > 350 °C), and were hard and brittle. The copolymers of monomer (D) were prepared with fluorovinyl monomers such as chlorotrifluoroethylene (CTFE), perfluoropropyl vinyl ether, perfluoromethyl vinyl ether, and vinylidene fluoride. The kinetics of radical copolymerization of monomer (D) with CTFE led to the assessment of the reactivity ratios of both comonomers: r_D = 3.635 and r_CTFE = 0.737 at 74 °C, respectively. The copolymers obtained were soluble in HFB and perfluoro‐2‐butyltetrahydrofuran, with T_g in the range of 84–145 °C depending on the copolymer composition. The films of the copolymers were flexible and clear with a low refractive index (1.3350–1.3770 at 532 nm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6571–6578, 2009     

Tuning the LCST of poly(2‐cyclopropyl‐2‐oxazoline) via gradient copolymerization with 2‐ethyl‐2‐oxazoline

Poly(2‐propyl‐oxazoline)s can be prepared by living cationic ring‐opening polymerization of 2‐oxazolines and represent an emerging class of biocompatible polymers exhibiting a lower critical solution temperature in aqueous solution close to body temperature. However, their usability is limited by the irreversibility of the transition due to isothermal crystallization in case of poly(2‐isopropyl‐2‐oxazoline) and the rather low glass transition temperatures (T_g < 45 °C) of poly(2‐n‐propyl‐2‐oxazoline)‐based polymers. The copolymerization of 2‐cyclopropyl‐2‐oxazoline and 2‐ethyl‐2‐oxazoline presented herein yields gradient copolymers whose cloud point temperatures can be accurately tuned over a broad temperature range by simple variation of the composition. Surprisingly, all copolymers reveal lower T_gs than the corresponding homopolymers ascribed to suppression of interchain interactions. However, it is noteworthy that the copolymers still have T_gs > 45 °C, enabling convenient storage in the fridge for future biomedical formulations. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3118–3122     

Kinetics of radical copolymerization of [1‐(fluoromethyl)vinyl]benzene with chlorotrifluoroethylene

The synthesis of [1‐(fluoromethyl)vinyl]benzene (or α‐(fluoromethyl)styrene, FMB) and its radical copolymerization with chlorotrifluorethylene (CTFE), initiated by tert‐butyl peroxypivalate (TBPPi) are presented. The allyl monomer [H₂C = C(CH₂F)C₆H₅] was obtained by electrophilic fluorodesilylation of trimethyl(2‐phenylprop‐2‐en‐1‐yl)silane in 93% yield. A series of seven copolymerization reactions were carried out starting from initial [CTFE]₀/([FMB]₀ + [CTFE]₀) molar ratios ranging from 19.6 to 90.0 mol %. The molar compositions of the obtained poly(CTFE‐co‐FMB) copolymers were assessed by means of ¹⁹F nuclear magnetic resonance spectroscopy. Statistic copolymers were produced with molar masses ranging between 13,800 and 25,600 g/mol. From the Kelen and Tudos method, the kinetics of the copolymerization led to the determination of the reactivity ratios, r_i, of both comonomers (r_CTFE = 0.4 ± 0.2 and r_FMB = 3.7 ± 1.8 at 74 °C) showing that FMB is more reactive than CTFE as well as other halogenated or nonhalogenated monomers involved in the radical copolymerization with CTFE. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3843–3850, 2007     

Synthesis and properties of the ionomer diblock copolymer poly(4‐vinylbenzyl triethyl ammonium bromide)‐b‐polyisobutene

A new amphiphilic diblock copolymer containing an ionomer segment, poly[(4‐vinylbenzyl triethyl ammonium bromide)‐co‐(4‐methylstyrene)‐co‐(4‐bromomethylstyrene)]‐b‐polyisobutene [poly(4‐VBTEAB)‐b‐PIB], was synthesized by the chemical modification of poly(4‐methylstyrene)‐b‐polyisobutene [poly(4‐MSt)‐b‐PIB]. First, the 4‐methylstyrene moiety in poly(4‐MSt)‐b‐PIB was brominated with azobisisobutyronitrile as an initiator at 60 °C in CCl₄, and then the highly reactive benzyl bromide groups were ionized by a reaction with triethylamine in a toluene/isopropyl alcohol (80/20 v/v) mixture at about 85 °C to produce the ionomer diblock copolymer poly(4‐VBTEAB)‐b‐PIB. The solubility of the ionomer block copolymer was quite different from that of the corresponding poly[(4‐methylstyrene)‐co‐(4‐bromomethylstyrene)]‐b‐polyisobutene {poly[(4‐MSt)‐co‐(4‐BrMSt)]‐b‐PIB}. Transmission electron microscopy observations demonstrated that all three diblock copolymers had microphase‐separation structures in which polyisobutene (PIB) domains existed in the continuous phase of the poly(4‐methylstyrene) segment or its derivative segment matrix. Dynamic mechanical thermal analysis measurements showed that poly[(4‐MSt)‐co‐(4‐BrMSt)]‐b‐PIB had two glass‐transition temperatures (T_g's), ?56 °C for the PIB segment and 62 °C for the poly[(4‐MSt)‐co‐(4‐BrMSt)] domain, whereas poly(4‐VBTEAB)‐b‐PIB showed one T_g at ?8 °C of the PIB domain; T_g of the poly[(4‐vinylbenzyl triethyl ammonium bromide)‐co‐(4‐methylstyrene)‐co‐(4‐bromomethylstyrene)] domain was not observable because of the strong ionic interactions resulting in a higher T_g and a retention of modulus up to 124 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2755–2764, 2003     

Synthesis of 3‐(tert‐Butoxycarbonylmethyl)‐N‐vinyl‐2‐caprolactam and Homologous Copolymerization Toward Biocompatible Carboxylated Poly(N‐vinyl‐2‐caprolactam) Responsive to pH and Temperature

A new monomer derivative of N‐vinyl‐2‐caprolactam (VCL), namely 3‐(tert‐butoxycarbonylmethyl)‐N‐vinyl‐2‐caprolactam (TBMVCL), was synthesized via nucleophilic substitution at the α‐carbon to the lactam carbonyl group. The monomer was copolymerized radically with VCL and the copolymer compositions were controlled through varying the molar feeding percentages of TBMVCL. The resulting copolymers exhibited temperature‐responsive properties in water, with cloud points decreasing from 33 °C to 13 °C when the TBMVCL composition increased from 2.2 mol % to 18.6 mol %. Removal of the tert‐butyl protecting groups via acid hydrolysis exposed the carboxyl groups, which conferred pH sensitivity to the thermoresponsive properties of the resulting deprotected copolymers. The cloud point was found to increase with the increase of solution pH from 2.0 to 7.4, due to the ionization of the carboxyl groups. The influence of pH was most drastic for the 18.6 mol % copolymer composition. Furthermore, the phase transition temperature of the deprotected copolymers was found to be dependent on the polymer solution concentration, exemplifying classical Flory–Huggins miscibility behavior. Comparison of responsiveness was also made with another type of carboxyl functionalized poly(N‐vinyl‐2‐caprolactam) copolymer reported in our prior study, to examine the influence of the chemical structure of the carboxyl substitution group. Finally, the deprotected copolymer was demonstrated to be biocompatible using a fibroblast cell culture. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 112–120     

Stimuli‐responsive 4‐acryloylmorpholine/4‐acryloylpiperidine copolymers via nitroxide mediated polymerization

4‐acryloylmorpholine/4‐acryloylpiperidine statistical copolymers were synthesized by nitroxide mediated polymerization (NMP) with BlocBuilder unimolecular initiator in dimethylformamide solution at 120 °C. The copolymers had narrow molecular weight distributions (dispersity ? = 1.25–1.35, number average molecular weights M _n = 8.5–13.7 kg mol^?1). The copolymer microstructure was essentially statistical (reactivity ratios r _4AP = 0.81 ± 0.73, r _4AM = 0.73 ± 0.68 based on non‐linear fitting of the Mayo‐Lewis equation). Cloud point temperatures (CPT) in aqueous media were tuned from 11 °C to 92 °C, merely by adjusting the initial monomer composition. Using NMP permitted sharper control of the CPT transitions, compared to the similar copolymer made using conventional radical polymerization. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2160–2170     

Enhancing the glass‐transition temperature of polyimide copolymers containing 2,2′‐bipyridine units by the coordination of nickel malenonitriledithiolate

Polyimide copolymers containing 2,2′‐bipyridine were synthesized and characterized. The glass‐transition temperatures (T_g's) of the polymers ranged from 260 to 300 °C. In contrast to most known organic chromophore‐containing polyimides, the polyimide copolymers in this study showed elevated T_g's (270–320 °C) after coordination with nickel malenonitriledithiolate inorganic chromophores. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 498–503, 2000     

Poly(N‐phenylmaleimide‐co‐acrylic acid)–copper(II) and poly(N‐phenylmaleimide‐co‐acrylic acid)–cobalt(II) complexes: Synthesis,characterization, and thermal behavior

The free‐radical copolymerization of N‐phenylmaleimide (N‐PhMI) with acrylic acid was studied in the range of 25–75 mol % in the feed. The interactions of these copolymers with Cu(II) and Co(II) ions were investigated as a function of the pH and copolymer composition by the use of the ultrafiltration technique. The maximum retention capacity of the copolymers for Co(II) and Cu(II) ions varied from 200 to 250 mg/g and from 210 to 300 mg/g, respectively. The copolymers and polymer–metal complexes of divalent transition‐metal ions were characterized by elemental analysis, Fourier transform infrared, ¹H NMR spectroscopy, and cyclic voltammetry. The thermal behavior was investigated with differential scanning calorimetry (DSC) and thermogravimetry (TG). The TG and DSC measurements showed an increase in the glass‐transition temperature (T_g) and the thermal stability with an increase in the N‐PhMI concentration in the copolymers. T_g of poly(N‐PhMI‐co‐AA) with copolymer composition 46.5:53.5 mol % was found at 251 °C, and it decreased when the complexes of Co(II) and Cu(II) at pHs 3–7 were formed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4933–4941, 2005     

Synthesis and properties of copolymers of methyl methacrylate with 2,3,4,5,6‐pentafluoro and 4‐trifluoromethyl 2,3,5,6‐tetrafluoro styrenes: An intrachain interaction between methyl ester and fluoro aromatic moieties

2,3,4,5,6‐Pentafluoro and 4‐trifluoromethyl 2,3,5,6‐tetrafluoro styrenes were readily copolymerized with methyl methacrylate (MMA) by a free radical initiator. The copolymers were soluble in tetrahydrofuran and acetone. The films obtained were transparent and flexible. The glass transition temperatures (T_gs) of the copolymers were found positively deviated from the Gordon–Taylor equation. The positive deviation could be accounted for by dipole–dipole intrachain interaction between the methyl ester group of MMA and the highly fluorinated aromatic moiety, which resulted in a decrease in the segmental mobility of the polymer chains and the enhanced T_g values of the copolymers. The water absorption of PMMA was greatly decreased by copolymerization of MMA with the highly fluorinated styrenes. With as little as 10 mol % of pentafluoro styrene content in the copolymer, the water absorption was decreased to one‐third of that for pure PMMA. The fluorinated styrenes‐MMA copolymers were thermally stable up to 420 °C under air and nitrogen atmospheres. With 50 mol % of MMA in the copolymer, the copolymer was still stable up to 350 °C. Since these copolymers contain a large number of fluorine atoms, the light absorption in the region of the visible to near infrared is decreased in comparison with nonfluorinated polymers. Thus, these copolymers may be suitable for application in optical devices, such as optical fibers and waveguides. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of well‐defined block and statistical copolymers based on lauryl methacrylate and 2‐(acetoacetoxy)ethyl methacrylate using RAFT‐controlled radical polymerization

Four well‐defined diblock copolymers and one statistical copolymer based on lauryl methacrylate (LauMA) and 2‐(acetoacetoxy)ethyl methacrylate (AEMA) were prepared using reversible addition‐fragmentation chain transfer (RAFT) polymerization. The polymers were characterized in terms of molecular weights, polydispersity indices (ranging between 1.12 and 1.23) and compositions by size exclusion chromatography and ¹H NMR spectroscopy, respectively. The preparation of the block copolymers was accomplished following a two‐step methodology: First, well‐defined LauMA homopolymers were prepared by RAFT using cumyl dithiobenzoate as the chain transfer agent (CTA). Kinetic studies revealed that the polymerization of LauMA followed first‐order kinetics demonstrating the “livingness” of the RAFT process. The pLauMAs were subsequently used as macro‐CTA for the polymerization of AEMA. The glass transition (T_g) and decomposition temperatures (ranging between 200 and 300 °C) of the copolymers were determined using differential scanning calorimetry and thermal gravimetric analysis, respectively. The T_gs of the LauMA homopolymers were found to be around ?53 °C. Block copolymers exhibited two T_gs suggesting microphase separation in the bulk whereas the statistical copolymer presented a single T_g as expected. Furthermore, the micellization behavior of pLauMA‐b‐pAEMA block copolymers was investigated in n‐hexane, a selective solvent for the LauMA block, using dynamic light scattering. pLauMA‐b‐pAEMA block copolymers formed spherical micelles in dilute hexane solutions with hydrodynamic diameters ranging between 30 and 50 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5442–5451, 2008     

Thermal and spectral stability of electroluminescent hyperbranched copolymers containing tetraphenylthiophene‐quinoline‐triphenylamine moieties

Fluorescent hyperbranched copolymers (HB‐x, x = 1–4) with inherent tetraphenylthiophene, triphenylamine (TPA) and quinoline (Qu) moieties were prepared to study the influence of the TPA branching point on the thermal and the spectral stability. All the HB‐x copolymers exhibited high glass transition temperatures (T_gs = 245–315 °C) with the detected values increasing with the increasing branching TPA content in the HB‐x. The solid HB‐x films possess high emission efficiency with the resulting quantum yields (?_Fs) in the ranges of 0.72–0.74. More importantly, the HB‐x copolymers and the derived light‐emitting devices exhibit high photoluminescence (PL) and electroluminescence (EL) stability towards thermal annealing at temperatures higher than 200 °C. After annealing at 200 °C (or 300 °C), no change was observed in the respective PL and EL spectra of HB‐1 (or HB‐4) copolymers. The spectral stability was found to correlate with T_g and with the highest branching density, HB‐4 copolymer possesses the highest thermal stability among all HB‐xs and show no EL spectral change after annealing at 300 °C for 4 h. The results indicate that all the branched HB‐x copolymers are promising candidates for the polymer light‐emitting diodes due to their high quantum yield and spectral stability. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and polymerization of fluorinated monomers bearing a reactive lateral group. XIV. Radical copolymerization of vinylidene fluoride with methyl 1,1‐dihydro‐4,7‐dioxaperfluoro‐5,8‐dimethyl non‐1‐enoate

The radical copolymerization in solution of vinylidene fluoride (VDF; or 1,1‐difluoroethylene) with methyl 1,1‐dihydro‐4,7‐dioxaperfluoro‐5,8‐dimethyl non‐1‐enoate (MDP) initiated by di‐tert‐butyl peroxide is presented. Six copolymerization reactions were investigated with initial [VDF]₀/[MDP]₀ molar ratios of 35/65 to 80/20. Both of these comonomers copolymerized in this range of copolymerization. Moreover, these comonomers homopolymerized separately under these conditions. The copolymer compositions of these random copolymers were calculated by means of ¹⁹F NMR spectroscopy, which allowed the quantification of the respective amounts of each monomeric unit in the copolymers. The Tidwell–Mortimer method was used for the assessment of the reactivity ratios (r_i) of both comonomers, which showed a higher incorporation of MDP in the copolymers (r_MDP = 2.41 ± 2.28 and r_VDF = 0.38 ± 0.21 at 120 °C). The Alfrey–Price Q and e values of the trifluoroallyl monomer MDP were calculated to be 0.024 (from Q_VDF = 0.008) or 0.046 (from Q_VDF = 0.015) and 0.70 (vs e_VDF = 0.40) or 0.80 (vs e_VDF = 0.50), respectively, indicating that MDP was an electron‐accepting monomer. The thermal properties of these fluorinated copolymers were also determined. Except for those containing a high amount of VDF, the copolymers were amorphous. Each showed one glass‐transition temperature (T_g) only, and with known laws of T_g's, T_g of the MDP homopolymer was assessed. It was compared to that obtained from the direct radical homopolymerization of MDP and discussed. Indeed, these two values were close (T_g = ?3 °C). Thermogravimetric analyses were performed, and they showed that the copolymers were rather thermostable because the thermal degradation occurred at 280 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3109–3121, 2003     

Synthesis of biodegradable thermoplastic elastomers from ε‐caprolactone and lactide

This article reports the synthesis and the properties of novel thermoplastic elastomers of A‐B‐A type triblock copolymer structure, where the hard segment A is poly(l ‐lactide) (PLLA) and the soft segment B is poly(ε‐caprolactone‐stat‐d ,l ‐lactide) (P(CL‐stat‐DLLA)). The P(CL‐stat‐DLLA) block with DLLA content of 30 mol % was applied because of its amorphous nature and low glass transition temperature (T_g = approximately ?40 °C). Successive polymerization of l ‐lactide afforded PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLAs, which exhibited melting temperature (T_m = approximately 150 °C) for the crystalline PLLA segments and still low T_g (approximately ?30 °C) of the soft segments. The triblock copolymers showed very high elongation at break up to approximately 2800% and elastic properties. The corresponding d ‐triblock copolymers, PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLAs (PDLA = poly(d ‐lactide)) were also prepared with the same procedure using d ‐lactide in place of l ‐lactide. When the PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLA was blended with PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLA, stereocomplex crystals were formed to enhance their T_m as well as tensile properties. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 489–495     

Synthesis and properties of poly(imide‐hydrazide)s and poly(amide‐imide‐hydrazide)s from N‐[p‐(or m‐)carboxyphenyl]trimellitimide and aromatic dihydrazides or p‐aminobenzhydrazide via the phosphorylation reaction

A series of new poly(imide‐hydrazide)s and poly(amide‐imide‐hydrazide)s were obtained by the direct polycondensation of N‐[p‐(or m‐)carboxyphenyl]trimellitimide (p‐ or m‐CPTMI) with terephthalic dihydrazide (TPH), isophthalic dihydrazide (IPH), and p‐aminobenzhydrazide (p‐ABH) by means of diphenyl phosphite and pyridine in the N‐methyl‐2‐pyrrolidone (NMP) solutions containing dissolved CaCl₂. The resulting hydrazide‐containing polymers exhibited inherent viscosities in the 0.15–0.96 dL/g range. Except for that derived from p‐CPTMI with TPH or p‐ABH, the other hydrazide copolymers were readily soluble in polar solvents such as NMP and dimethyl sulfoxide (DMSO). As evidenced by X‐ray diffraction patterns, the hydrazide copolymer obtained from TPH showed a moderate level of crystallinity, whereas the others were amorphous in nature. Most of the amorphous hydrazide copolymers formed flexible and tough films by solvent casting. The amorphous hydrazide copolymers had glass‐transition temperatures (T_g) between 187 and 233 °C. All hydrazide copolymers could be thermally converted into the corresponding oxadiazole copolymers approximately in the region of 250–400 °C, as evidenced by the DSC thermograms. The oxadiazole copolymers showed a significantly decreased solubility when compared to their respective hydrazide precursors. They exhibited T_g's of 264–302 °C and did not show dramatic weight loss before 400 °C in air or nitrogen. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1599–1608, 2000     

“Smart” poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) copolymers synthesized by nitroxide mediated radical polymerization

A series of poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(DMAEMA‐ran‐VBK)) random copolymers, with VBK molar feed compositions f_VBK,0 = 0.02–0.09, were synthesized using 10 mol % [tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] nitroxide (SG1) relative to 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropionic acid (BlocBuilder) at 80 °C and 90 °C. Controlled polymerizations were observed, even with f_VBK,0 = 0.02, as reflected by a linear increase in number average molecular weight (M_n) versus conversion X ≤ 0.6 with final copolymers characterized by relatively narrow, monomodal molecular weight distributions (M_w/M_n ≈ 1.5). Poly(DMAEMA‐ran‐VBK) copolymers were deemed sufficiently pseudo‐“living” to reinitiate a second batch of N,N‐dimethylacrylamide (DMAA), with very few apparent dead chains, as indicated by the monomodal shift in the gel permeation chromatography chromatograms. Poly(DMAEMA‐ran‐VBK) random copolymers exhibited tuneable lower critical solution temperature (LCST), in aqueous solution, by modifying copolymer composition, solution pH and by the addition of the water‐soluble poly(DMAA) segment. ¹H NMR analysis determined that, in water, the VBK units of the poly(DMAEMA‐ran‐VBK) random copolymer were segregated to the interior of the copolymer aggregate regardless of solution temperature and that poly(DMAEMA‐ran‐VBK)‐b‐poly(DMAA) block copolymers formed micelles above the LCST. In addition, the final random copolymer and block copolymer exhibited temperature dependent fluorescence due to the VBK units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Novel amorphous perfluorocopolymeric system: Copolymers of perfluoro‐2‐methylene‐1,3‐dioxolane derivatives

Perfluorotetrahydro‐2‐methylene‐furo[3,4‐d][1,3]dioxole (monomer I ) and perfluoro‐2‐methylene‐4‐methoxymethyl‐1,3‐dioxolane (monomer II ) are soluble in perfluorinated or partially fluorinated solvents and readily polymerize in solution or in bulk when initiated by a free‐radical initiator, perfluorodibenzoyl peroxide. The copolymerization parameters have been determined with in situ ¹⁹F NMR measurements. The copolymerization reactivity ratios are r _I = 1.80 and r _II = 0.80 in 1,1,2‐trichlorotrifluoroethane at 41 °C and r _I = 0.97 and r _II = 0.85 for the bulk polymerization. These data show that this copolymerization pair has a good copolymerization tendency and yields nearly ideal random copolymers. The copolymers have only one glass‐transition temperature from 101 to 168 °C, depending on the copolymer compositions. Melting endotherms have not been observed in their differential scanning calorimetry traces, and this indicates that all the copolymers with different compositions are completely amorphous. These copolymers are thermally stable (the initial decomposition temperatures are higher than 350 °C under an N₂ atmosphere) and have low refractive indices and high optical transparency from UV to near‐infrared. Copolymer films prepared by casting were flexible and tough. These properties make the copolymers ideal candidates as optical and electrical materials. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1613–1618, 2006     

Synthesis and characterization of original alternated fluorinated copolymers bearing glycidyl carbonate side groups

A vinyl ether bearing a carbonate side group (2‐oxo‐1,3‐dioxolan‐4‐yl‐methyl vinyl ether, GCVE) was synthesized and copolymerized with various commercially available fluoroolefins [chlorotrifluoroethylene (CTFE), hexafluoropropylene (HFP), and perfluoromethyl vinyl ether (PMVE)] by radical copolymerization initiated by tert‐butyl peroxypivalate. Although HFP, PMVE, and vinyl ether do not homopolymerize under radical conditions, they copolymerized easily yielding alternating poly(GCVE‐alt‐F‐alkene) copolymers. These alternating structures were confirmed by elemental analysis as well as ¹H, ¹⁹F, and ¹³C NMR spectroscopy. All copolymers were obtained in good yield (73–85%), with molecular weights ranging from 3900 to 4600 g mol^?1 and polydispersities below 2.0. Their thermogravimetric analyses under air showed decomposition temperatures at 10% weight loss (T_d,10%) in the 284–330°C range. The HFP‐based copolymer exhibited a better thermal stability than those based on CTFE and PMVE. The glass transition temperatures were in the 15–65°C range. These original copolymers may find potential interest as polymer electrolytes in lithium ions batteries. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012