Fast Removal and Recovery of Methylene Blue by Activated Carbon Modified with Magnetic Iron Oxide Nanoparticles

A magnetic adsorbent was synthesized by modification of activated carbons with magnetic iron oxide nanoparticles (AC‐MIONs). The preparation method is fast and could be carried out in an ordinary condition. The AC‐MIONs were used as quite efficient adsorbents for separation of methylene blue (MB) from aqueous solution in a batch process. The effect of different parameters such as pH, temperature, electrolyte concentration, contact time and interfering ions on the removal of MB were studied. The adsorption data were analyzed by Langmuir and Freundlich isotherm models and a maximum adsorption amount of 47.62 mg g^‐1 and a langmuir adsorption equilibrium constant of 3.0 L mg^‐1 were obtained. The obtained results revealed that AC‐MIONs were effective adsorbents for fast removal of MB from different aqueous solutions. This adsorbent was successfully used for removal of MB from Karoon River water.     

Modification of microcrystalline cellulose with pyridone derivatives for removal of cationic dyes from aqueous solutions

Microcrystalline cellulose (MCC) was modified with pyridone derivatives such as pyridone diester (PDE) and pyridone diacid (PDA) by using succinic acid anhydride as a linker. The modified MCCs were characterized by the fourier transform infrared spectroscopy, scanning electron microscopy, thermal gravimetric analysis, elemental analysis and solid state ¹³C NMR. The adsorption capacities of the modified MCCs to cationic dyes were examined by using methylene blue (MB) as a model dye. It was found that the kinetic adsorption data followed the pseudo-second-order kinetic model, and the adsorption equilibriums were reached less than 10 min. The isothermal adsorption data were fitted with the Langmuir isotherm model very well, from which the maximum adsorption capacities of the MCCs modified with PDE and PDA were determined to be 101.01 and 142.86 mg/g, respectively. Further investigation showed that the modified MCCs were pH-dependent for adsorption of MB in aqueous solutions. The modified MCCs could be used for removal of MB from an aqueous solution at pH 8, and reused by regeneration in an acidic solution. It was tested that the modified MCCs had a high reusability for removal of MB from aqueous solutions, and still maintained high adsorption capacities even after multiple cycles of desorption–adsorption processes. Hence, the MCCs modified with PDE and PDA could be an effective and efficient approach to removal of cationic dyes from aqueous solutions.     

Experimental and Theoretical Insights on Methylene Blue Removal from Wastewater Using an Adsorbent Obtained from the Residues of the Orange Industry

Chemical and thermochemical transformations were performed on orange peel to obtain materials that were characterized and further tested to explore their potential as adsorbents for the removal of methylene blue (MB) from aqueous solutions. The results show the high potential of some of these materials for MB adsorption not only due to the surface area of the resulting substrate but also to the chemistry of the corresponding surface functional groups. Fitting of the kinetic as well as the equilibrium experimental data to different models suggests that a variety of interactions are involved in MB adsorption. The overall capacities for these substrates (larger than 192.31 mg g⁻¹) were found to compare well with those reported for activated carbon and other adsorbents of agro-industrial origin. According to these results and complementary with theoretical study using Density Functional Theory (DFT) approximations, it was found that the most important adsorption mechanisms of MB correspond to: (i) electrostatic interactions, (ii) H-bonding, and (iii) π (MB)–π (biochar) interactions. In view of these findings, it can be concluded that adsorbent materials obtained from orange peel, constitute a good alternative for the removal of MB dye from aqueous solutions.     

Monodisperse Mw-Pt NPs@VC as Highly Efficient and Reusable Adsorbents for Methylene Blue Removal

Addressed herein, monodisperse Vulcan carbon supported Pt nanoparticles (Mw-Pt NPs@VC) have been reproducibly synthesized using the microwave assisted method and their application for methylene blue (MB) removal from aqueous solutions was investigated through the adsorption mechanism. The prepared nanomaterials were characterized by X-ray diffraction, transmission electron microscopy, high resolution transmission electron microscopy and X-ray photoelectron spectroscopy. All results show that highly crystalline and colloidally stable nanoparticles have been formed and Mw-Pt NPs@VC were found to be one of the the most active catalyst. The results showed that the Mw-Pt NPs@VC nanoparticles had remarkable MB adsorption capacity of 271.15 mg/g. The equilibrium for MB adsorption was attained in ～55 min. Moreover, Mw-Pt NPs@VC is a reusable and promising material for MB removal since it preserves 95.6 % of its initial efficiency after six successive cycles of adsorption–desorption.     

ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理

采用电弧放电法制备了ZnO/C纳米球,利用FESEM、XRD和N₂吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g^-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理

采用电弧放电法制备了ZnO/C纳米球,利用FESEM、XRD和N₂吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g^-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

掺杂铜的介孔SiO2微球的制备以及对亚甲基蓝的吸附

通过水热法在室温下合成了不同铜含量的介孔SiO2微球(Cu-MSM)。目的在于研究吸附剂量、MB的初始浓度以及吸附时间对Cu-MSM从溶液中移除亚甲基蓝(MB)吸附性能的影响。结果表明,当增加Cu-MSM的量时,MB的去除率会大大提高;掺杂铜的介孔SiO2微球可以通过吸附去除水溶液中的亚甲蓝。最后,简要探讨了亚甲基蓝的吸附机理。     

Adsorption of methylene blue dye from aqueous solution by agricultural waste: Equilibrium,thermodynamics, kinetics,mechanism and process design

The adsorption of methylene blue (MB) dye from aqueous solution onto a cashew nut shell (CNS) was investigated as a function of parameters such as solution pH, CNS dose, contact time, initial MB dye concentration and temperature. The CNS was shown to be effective for the quantitative removal of MB dye, and the equilibrium was reached in 60 min. The experimental data were analysed by two-parameter isotherms (Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models) using nonlinear regression analysis. The characteristic parameters for each isotherm and the related correlation coefficients were determined. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were also evaluated, the sorption process was found to be spontaneous and exothermic. Pseudo-first-order, pseudo-second-order and Elovich kinetic models were used to analyze the adsorption process. The results of the kinetic study suggest that the adsorption of MB dye matches the pseudo-second-order equation, suggesting that the adsorption process is presumably chemisorption. The adsorption process was found to be controlled by both surface and pore diffusion. Analysis of adsorption data using a Boyd kinetic plot confirmed that the external mass transfer is a rate determining step in the sorption process. A single-stage batch adsorber was designed for different CNS doses to effluent volume ratios using the Freundlich equation. The results indicated that the CNS could be used effectively to adsorb MB dye from aqueous solutions.     

ADSORPTION OF METHYLENE BLUE FROM AQUEOUS SOLUTION ON ATTAPULGITE

Batch adsorption experiments were carried out for the removal of methylene blue （MB） from aqueous solution using attapulgite as adsorbent. The effects of various parameters such as temperature, contact time, the pH value, and attapulgite dosage on the adsorption performance were investigated. The standard curve and regression equation were established by spectrophotometry. The adsorption experimental results showed that the adsorption equilibrium data were well in accord with Langmuir adsorptive model. The optimal result was acquired under the experimental condition of attapulgite dosage 0.18g, MB concentration 50.0mg/L, pH 10, and adsorption time 20min at room temperature.     

Kinetics of adsorption and desorption of Pb(II) in aqueous solution on activated carbon by two-site adsorption model

The adsorption and desorption equilibrium and kinetics of lead ions from aqueous solutions on a granular activated carbon (GAC) were examined. Rapid increase followed by slow increase in Pb(II) amount on the GAC was observed as a function of time for the adsorption, while rapid decrease and consecutive very slow decrease was observed in desorption. Based on the experimental results, a two-site adsorption model was proposed for the adsorption and the desorption of Pb(II) under the study conditions. The Pb(II) adsorption on the GAC was estimated to have simultaneously occurred on the strong and the weak adsorption sites. Conventional Langmuir-type kinetic equations were introduced to quantitatively predict the adsorption and desorption with the two-site model by optimizing the parameters to fit the equilibrium and the kinetic experimental results. The equilibrium and kinetic experimental results could be represented by the equations by using one set of the common Langmuir parameters. Resultant kinetic parameters revealed that the adsorption equilibrium constant was two orders of magnitude greater for strong adsorption site than for weak adsorption site, though the maximum number of weak adsorption site was 1.5 times as great as that of strong adsorption site. The strong adsorption equilibrium constant resulted from a small desorption rate constant for the site. The equations were demonstrated to be applicable for predicting other desorption performances as well.     

Multi‐responses optimization of simultaneous adsorption of methylene blue and malachite green dyes in binary aqueous system onto Ni:FeO(OH)‐NWs‐AC using experimental design: derivative spectrophotometry method

In this research, response surface methodology (RSM) approach using Central Composite Design (CCD) coupled by derivative spectrophotometry method was applied to develop mathematical model and optimize process parameters for simultaneous adsorption of methylene blue (MB) and malachite green (MG) from aqueous solution using Ni:FeO(OH) ‐ NWs‐AC. The optimal conditions to adsorption of MB and MG in binary mixture solution from aqueous solution were found at pH 8.0, MB concentration 20 mg L^‐1, MG concentration 20 mg L^‐1, adsorbent dosage 0.033 g and contact time 40 min. At these conditions, high adsorption efficiency (99.39% and 100.0% for MB and MG, respectively) was achieved. Among experimental equilibrium, Langmuir isotherm model fitted well with maximum monolayer adsorption capacity of 28.6 and 29.8 mg g^‐1 for MB and MG, respectively. The adsorption kinetic data followed pseudo second‐order kinetics for MB and MG dyes.     

玻璃硅烷化处理对罗丹明6G和亚甲基蓝吸附行为的影响

利用六甲基二硅烷胺对平面玻璃光波导(高折射率透明导光薄膜介质)进行硅烷化处理, 得到水接触角大于90°的疏水表面. 然后使用时间分辨光波导分光光谱技术研究水溶液中的罗丹明6G (R6G)和亚甲基蓝(MB)分子在疏水玻璃表面的吸附行为, 并与亲水玻璃条件下测得的结果进行对比. 对利用疏水玻璃光波导测得的R6G的吸附-脱附动力学曲线进行Langmuir拟合得到了R6G的吸附速率常数, 脱附速率常数以及吸附自由能. 并且发现与亲水玻璃情况相比, 吸附速率常数增大, 脱附速率常数减小, 吸附自由能更负. 在疏水玻璃表面形成的R6G和MB吸附层的吸光度与亲水玻璃情况相比显著升高, 表明这两种分子更倾向于吸附在疏水玻璃表面. 实验结果还发现玻璃硅烷化处理能够有效抑制这两种染料分子在表面的聚合反应.     

Adsorption of anionic and cationic dyes by activated carbons, PVA hydrogels, and PVA/AC composite

The textural and adsorption characteristics of a series of activated carbons (ACs), porous poly(vinyl alcohol) (PVA) gels, and PVA/AC composites were studied using scanning electron microscopy, mercury porosimetry, adsorption of nitrogen (at 77.4 K), cationic methylene blue (MB), anionic methyl orange (MO), and Congo red (CR) from the aqueous solutions. Dye-PVA-AC-water interactions were modeled using the semiempirical quantum chemical method PM6. The percentage of dye removed (C(rem)) by the ACs was close to 100% at an equilibrium concentration (C(eq)) of less than 0.1 mM but decreased with increasing dye concentration. This decrease was stronger at C(eq) of less than 1 mM, and C(rem) was less than 50% at a C(eq) of 10-20 mM. For PVA and the PVA/AC composite containing C-7, the C(rem) values were minimal (<75%). The free energy distribution functions (f(ΔG)) for dye adsorption include one to three peaks in the -ΔG range of 1-60 kJ/mol, depending on the dye concentration range used and the spatial, charge symmetry of the hydrated dye ions and the structural characteristics of the adsorbents. The f(ΔG) shape is most complex for MO with the most asymmetrical geometry and charge distribution and adsorbed at concentrations over a large C(eq) range. For symmetrical CR ions, adsorbed over a narrow C(eq) range, the f(ΔG) plot includes mainly one narrow peak. MB has a minimal molecular size at a planar geometry (especially important for effective adsorption in slit-shaped pores) which explains its greater adsorptive capacity over that of MO or CR. Dye adsorption was greatest for ACs with the largest surface area but as molecular size increases adsorption depends to a greater extent on the pore size distribution in addition to total and nanopore surface areas and pore volume.     

Adsorption and kinetic studies of cationic and anionic dyes on pyrophyllite from aqueous solutions

The adsorption of cationic Methylene Blue (MB) and anionic Procion Crimson H-EXL (PC) dyes from aqueous medium on pyrophyllite was studied. Changes in the electrokinetics of pyrophyllite as a function of pH were investigated in the absence and presence of multivalent cations. The results show that pyrophyllite in water exhibits a negative surface charge within the range pH 2-12. Pyrophyllite is found to be a novel adsorbent for versatile removal of cationic and anionic dyes. The negative hydrophilic surface sites of pyrophyllite are responsible for the adsorption of cationic MB molecules. The adsorption of anionic PC dye is possible after a charge reversal by the addition of trivalent cation of Al. Nearly 2 min of contact time are found to be sufficient for the adsorption of both dyes to reach equilibrium. The experimental data follow a Langmuir isotherm with adsorption capacities of 70.42 and 71.43 mg dye per gram of pyrophyllite for MB and PC, respectively. For the adsorption of both MB and PC dyes, the pseudo-second-order chemical reaction kinetics provides the best correlation of the experimental data.     

Modified Calcium Alginate Beads with Sodium Dodecyl Sulfate and Clay as Adsorbent for Removal of Methylene Blue

In present study, we have investigated the effect of an anionic surfactant sodium dodecyl sulfate (SDS) and clay on calcium alginate beads was studied to remove methylene blue (MB) and to improve the adsorption capacity. The effects of various experimental parameters, such as shaking rate, initial dye concentration, temperature, and pH on the adsorption rate, have been studied. Equilibrium studies showed that the sorption of the dye was enhanced in presence of SDS. Scanning electron microscope (SEM) analysis showed that SDS entrapped beads have more pores and cavities which could be responsible for improved adsorption of MB. The kinetics of cationic dye adsorption nicely followed pseudo-second-order process. The evaluated thermodynamic parameters (ΔG ^o, ΔH ^o, ΔS ^o) suggest endothermic adsorption of MB. The results revealed that the surfactant entrapped alginate could be considered as potential adsorbents for MB removal from aqueous solutions.     

The preparation and adsorption properties of electrospun aramid nanofibers

The focus of this work is the preparation of aramid nanofibers via electrospinning technology and the study of their adsorption properties. In this article, aramid nanofibers were prepared by electrospinning aramid fibers solution with the addition of lithium chloride (LiCl). It showed a good adsorption capacity when methylene blue (MB) was used as the model target. There were much larger adsorption amounts and faster kinetics of uptaking target species of electrospun aramid nanofibers to MB than that of electrospun polyethersulfone (PES) nanofibers. Compared with activated carbon, aramid nanofibers also have a much faster adsorption rate to MB. Aramid nanofibers were subsequently used to effectively remove endocrine disruptors such as bisphenol A (BPA), phenol (Phe), and p‐hydroquinone (BPhe) from their aqueous solutions. Additionally, molecule imprinted technology enhances aramid nanofibers with much higher adsorption amounts and special adsorption property for endocrine disruptors. These results showed that aramid nanofibers have the potential to be used in environmental applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Utilization of Waste Biomass (Kitchen Waste) Hydrolysis Residue as Adsorbent for Dye Removal: Kinetic,Equilibrium, and Thermodynamic Studies

Kitchen waste hydrolysis residue (KWHR), which is produced in the bioproduction process from kitchen waste (KW), is usually wasted with potential threats to the environment. Herein, experiments were carried out to evaluate the potential of KWHR as adsorbent for dye (methylene blue, MB) removal from aqueous solution. The adsorbent was characterized using FT-IR and SEM. Adsorption results showed that the operating variables had great effects on the removal efficiency of MB. Kinetic study indicated pseudo-second-order model was suitable to describe the adsorption process. Afterwards, the equilibrium data were well fitted by using Langmuir isotherm model, suggesting a monolayer adsorption. The Langmuir monolayer adsorption capacity was calculated to be 110.13 mg/g, a level comparable to some other low-cost adsorbents. It was found that the adsorption process of MB onto KWHR was spontaneous and exothermic through the estimation of thermodynamic parameters. Thus, KWHR was of great potential to be an alternative adsorbent material to improve the utilization efficiency of bioresource (KW) and lower the cost of adsorbent for color treatment.     

Low-temperature synthesis of nanoparticle-assembled, transparent, and low-crystallized hydroxyapatite blocks

The mesoporous carbon CMK-3 adsorbent was prepared, characterized, and used for the removal of anionic methyl orange dye from aqueous solution. Adsorption experiments were carried out as batch studies at different contact time, pH, initial dye concentration, and salt concentration. The dye adsorption equilibrium was rapidly attained after 60 min of contact time. Removal of dye in acidic solutions was better than in basic solutions. The adsorption of dye increased with increasing initial dye concentration and salt concentration. The equilibrium data were analyzed by the Langmuir and Freundlich models, which revealed that Langmuir model was more suitable to describe the methyl orange adsorption than Freundlich model. Experimental data were analyzed using pseudo-first-order and pseudo-second-order kinetic models. It was found that kinetics followed a pseudo-second-order equation. Thermodynamic study showed that the adsorption was a spontaneous and exothermic process.     

Cd2+和Ni2+在粉煤灰上的吸附特性

考察了粉煤灰对Cd2+和Ni2+的单组分吸附和双组分吸附性能。结果表明,粉煤灰可有效吸附水溶液中的Cd2+和Ni2+,去除率随pH升高而增加。吸附约60min后趋于平衡。粉煤灰对Ni2+的吸附容量高于Cd2+。单组分吸附平衡符合Freundlich模型和Redlich Peterson (R P)模型。双组分吸附时,Ni2+和Cd2+之间存在明显的竞争吸附效应;随干扰离子浓度升高,竞争吸附效应增强。不同模型拟合结果表明,双组分吸附平衡符合Freundlich竞争吸附模型。脱附实验表明,Cd2+比Ni2+易于脱附;0.1mol/L HCl、0.1mol/L HNO3 和0.05mol/L H2SO4的脱附效果接近,对Cd2+脱附率>60%,对Ni2+脱附率>35%。