Use of hydroxylapatite composite membranes for analysis of bisphenol A

This study evaluates solid-phase micro-extraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS) to determine trace levels of bis-phenol A in water and leached from plastic containers. In our study, we used very thin composite membranes prepared in the laboratory. The extraction using headspace post-derivatization with bis(trimethylsilyl) trifluoroacetamide (BSTFA), containing 1 % trimethylchlorosilane (TMCS) vapor, following SPME was compared with extraction without derivatization. The SPME experimental procedures to extract bis-phenol A in water were optimized with a relatively polar polyacrylate (PA)-coated fiber, an extraction time of 50 min, and desorption at 300 °C for 2 min. Headspace derivatization following SPME was performed using 7 μL of BSTFA with 1 % TMCS at 65 °C for 30 s. The precision was 5.2 % without derivatization and 9.0 % headspace derivatization. The detection limit was determined to be at the nanogram per liter level. When SPME was used following headspace derivatization, the detection limit was one order of magnitude better than that achieved without derivatization. The results of this study reveal the adequacy of the SPME–GC–MS method for analyzing bisphenol A leached from plastic containers. The concentrations of bisphenol A leached from plastic containers into water ranged from 0.7 to 78.5 μg L^?1.     

Determination of gabapentin in human plasma by capillary electrophoresis-laser induced fluorescence detection with and without solid-phase extraction

We have developed two methods for the quantitation of gabapentin in human plasma. They are based on capillary electrophoresis with laser-induced fluorescence detection (CE-LIF) with and without solid-phase extraction (SPE) and the derivatizing reagent 5-(4,6-dichlorotriazinyl)amino fluoresencin. The conditions for derivatization, separation and extraction were investigated in detail, and the optimal labeling conditions include a temperature of 40?°C, a reaction time of 30?min, and the use of a borate buffer of pH 9.0 as the reaction medium. A borate buffer of pH 9.2 served as a background electrolyte for CE separations. The CE-LIF and SPE-CE-LIF methods have linear ranges of 5–200?nmol?L^?1 and 0.2–10?nmol?L^?1, respectively, and the limits of detection are 0.5 and 0.02?nmol?L^?1, respectively. The SPE-CE-LIF method was successfully applied to the determination of gabapentin in blood plasma samples.

Genotyping of intron 22 inversion of factor VIII gene for diagnosis of hemophilia A by inverse-shifting polymerase chain reaction and capillary electrophoresis

This is the first capillary electrophoresis (CE) analysis for diagnosis of hemophilia A (HA). The intron 22 inversion of factor VIII gene (F8) causes 40–50 % of severe bleeding disorder of HA in all human populations. Consequently, identification of the disease-causing mutations is becoming increasingly important for accurate genetic counseling and prenatal diagnosis. In this study, the key steps of inverse-shifting polymerase chain reaction (IS-PCR) and of short-end injection capillary electrophoresis were used for more specific and rapid genotyping of intron 22 inversion of F8. In IS-PCR, three specific primers were used to amplify 512-bp amplicon for wild type and 584-bp amplicon for patients with intron 22 inversion. The capillary gel electrophoresis (CGE) system was performed using 1× Tris–borate–EDTA (TBE) buffer containing 0.3 % (w/v) polyethylene oxide (PEO). The PCR amplicons were electrokinetically injected at 10 kV for 10 s at a temperature of 25 °C. The optimal short-end injection CGE was applied to detect the F8 gene of HA patients and carriers within 5 min. Intron 22 inversion was indeed found on some HA patients (13/35, 37.1 %). All genotyping results showed good agreement with DNA sequencing method and long-distance polymerase chain reaction (LD-PCR). The IS-PCR combined with short-end injection CGE method was feasible and efficient for intron 22 inversion screening of F8 in the HA populations.     

Solid-phase methylamidation for sialoglycomics by MALDI-MS

Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) has been a major approach for glycan analysis. However, the preferential cleavage of the sialic acid moiety by in- and post-source decay influences the determination of sialylated glycans by MALDI-MS. Many chemical derivatization methods were introduced to stabilize the sialylated glycan during MALDI-MS. Among current derivatization methods, methylamidation is a promising means for simultaneous analysis of natural sialylated glycans regardless of their sialic acid linkage types. Here, a novel derivatization method was developed, in which proteins were conjugated on the solid-phase support in order to stabilize the sialic acids by methylamidation and to reduce sample loss and contamination during the derivatization process. This derivatization strategy was used to investigate N-glycans from fetuin, a glycoprotein containing different types of complex N-glycans. The developed method was also applied to the N-glycan profiling of human serum from patients and healthy volunteers. Results were consistent with N-glycan profiling by HPLC-fluorescence detection. This new method provided a sensitive, simple, and robust approach for profiling glycan structures of complex samples.     

Design and synthesis of a hydrophilic fluorescent derivatization reagent for carboxylic acids, 4-N-(4-N-aminoethyl)piperazino-7-nitro-2,1,3-benzoxadiazole (NBD-PZ-NH2), and its application to capillary electrophoresis with laser-induced fluorescence detection

A hydrophilic fluorescent derivatization reagent for fatty acids, 4-N-(4-N-aminoethyl)piperazino-7-nitro-2,1,3-benzoxadiazole (NBD-PZ-NH(2)), was designed and synthesized. NBD-PZ-NH(2) possesses not only a fluorophore and a reacting group but also a positive charge group and, thus, was hydrophilic and suitable for application to capillary electrophoresis. NBD-PZ-NH(2) reacted with fatty acids in the presence of triphenylphosphine (TPP) and 2,2'-dipyridyl disulfide (DPDS) at room temperature within 10 min. The derivatives were strongly fluoresced and were positively charged at pH below 3. The derivatives of C4-C20 fatty acids were separated within 10 min in 50% acetonitrile in water containing 30 mM ammonium acetate and 1.0 M acetic acid by capillary electrophoresis with laser-induced fluorescence (CE-LIF) detection. The detection limits attained were 6.5 nM (signal-to-noise ratio of 3). It is proposed that NBD-PZ-NH(2) is a prominent derivatization reagent for fatty acids which is suitable for CE-LIF application.     

Analysis of citrate-capped gold and silver nanoparticles by thiol ligand exchange capillary electrophoresis

We report on the capillary electrophoretic behavior of citrate-capped gold and silver nanoparticles in aqueous medium when applying a ligand-exchange surface reaction with thiols. Gold nanoparticles (AuNPs) and silver nanoparticles (AgNPs) of similar size (39?±?6 and 41?±?7 nm, respectively) and shape were synthesized, covered with a citrate shell, and characterized by microscopic and spectroscopic techniques. The analysis of these NPs by CE was accomplished by using a buffer solution (pH 9.7; 40 mM SDS, 10 mM CAPS; 0.1 % methanol) containing the anions of thioctic acid or thiomalic acid. These are capable of differently interacting with the surface of the AuNPs and AgNPs and thus introducing additional negative charges. This results in different migration times due to the formation of differently charged nanoparticles. Figure

Capillary electrophoretic behavior of citrate-capped gold and silver nanoparticles (NPs) in aqueous medium when applying a ligand-exchange surface reaction with thiols (thioctic and thiomalic acids), which introduces additional negative charges, has been studied     

A paper-based lateral flow assay for morphine

Morphine was used as a model analyte to examine the possibility of using cellulose, physically modified by papermaking and converting techniques, as a capillary matrix in a lateral flow type of diagnostic assay. This research was directed toward low-cost, disposable, and portable paper-based diagnostics, with the aim of addressing the analytical performance of paper as a substrate in the analysis for drugs of abuse. Antibody Fab fragments were used as sensing molecules, and gold nanoparticle detection was employed. Inkjet printing was used to pattern sensing biomolecules as detection zones on paper. To validate the usefulness of paper as a diagnostic platform, the principle of a direct sandwich assay, based on immunocomplex formation between morphine and the anti-morphine Fab fragment and detection of the formed immunocomplex by another Fab fragment, was implemented. Results were compared with that achieved by using nitrocellulose as a reference material. Possible interfering from the sample matrix on assay quality was investigated with spiked oral fluid samples. Under optimized conditions, a visually assessed limit of detection for the sandwich assay was 1 ng/mL, indicating that the paper-based test devices developed in this work can perform screening for drugs of abuse and can fulfill the requirement for a sensitive assay in diagnostically relevant ranges. Fig

?     

Capillary Electrophoresis Method for the Chiral Purity Determination of Pregabalin Derivatized with Dansyl Chloride

A capillary electrophoresis method for the determination of the chiral purity of pregabalin upon derivatization with dansyl chloride was developed using design of experiment methodologies. A D-optimal design was used for the identification of the critical process parameters, while a central composite face centered design and Monte Carlo simulations were employed for defining the design space of the method. Final working conditions consisted of a background electrolyte composed of a 100 mM sodium phosphate buffer, pH 2.5, containing 40 mg mL^?1 heptakis(2,3,6-tri-O-methyl)-β-cyclodextrin, a separation voltage of 15 kV and a capillary temperature of 25 °C. The analyses were carried out in a 40/50.2 cm fused-silica capillary with an inner diameter of 50 µm. Upon testing the robustness using a Plackett–Burman design, the method was validated according to the International Council on Harmonization guideline Q2(R1). The method allowed the detection of the (R)-enantiomer at the 0.015% level with a limit of quantitation at the 0.05% level with regard to a sample containing 1.59 mg mL^?1 pregabalin. The method was subsequently applied to the determination of the stereochemical purity of the drug in commercial capsules.     

Characterization of chitosan microparticles reinforced cellulose biocomposite sponges regenerated from ionic liquid

The chitosan-microparticles reinforced cellulose biocomposite sponges regenerated from ionic liquid were prepared and characterized. Fourier transform infrared (FTIR) spectroscopy confirmed that the cellulose dissolved in 1-allyl-3-methylimidazolium chloride without derivatization. Chitosan particles as reinforcement were incorporated into the cellulose matrix. FTIR spectra indicated hydrogen bonding between hydroxyl groups of cellulose and chitosan. The biocomposite sponges showed uniform three-dimensional interconnected porous structures. The breaking strength of the sponges increased significantly, from 0.09 to 0.32 MPa with the addition of 1.0 wt% chitosan. The sponges also demonstrated excellent antibacterial activity against S. aureus and E. coli with the average inhibition zone diameters >2 mm and the inhibition rate higher than 80 %. Furthermore, the biocomposite sponges exhibited good moisture penetrability and high porosity. The water uptake ability of the sponge was >25 times of its weight in water with a fast swelling. The chitosan/cellulose composite sponge is expected to be a promising material for potential applications as wound dressing.     

Preparation and reflow soldering characteristics of solder paste containing submicron Sn powders synthesised via chemical reduction

Sn nanoparticles (NPs) were synthesised via chemical reduction. Trisodium citrate dihydrate and mixtures of trisodium citrate dihydrate and 1,10-phenanthroline monohydrate were used as capping agents for the synthesis. When a specific amount of trisodium citrate dihydrate (3.4 × 10^?1 mM) was solely added, very fine particle sizes and excellent suppression of aggregation were achieved in the dried samples. When 5 mM of 1,10-phenanthroline monohydrate was used in combination with trisodium citrate dihydrate (at the optimum concentration of 3.4 × 10^?2 mM), the particle refining and the suppression of aggregation were further improved. The nano-solder paste prepared by mixing the synthesised Sn NPs with a commercial flux exhibited stable reflow soldering characteristics. The formation of an intermetallic layer, similar to that observed when commercial solder pastes containing micron-sized powders were used, was seen when soldering was carried out with the solder paste containing the synthesised Sn NPs.     

Purification of cellulosic pulp by hot water extraction

Hot water extraction (HWE) of pulp in a flow-through reactor was evaluated as a method to purify paper-grade pulps. About 50–80 % of the xylan and up to 50 % of the lignin in unbleached birch Kraft pulp was extracted by the HWE without losses in cellulose yield. The residual xylan content in the extracted pulps was predominantly too high for dissolving-grade applications, but some of the pulps with a xylan content of 5–7 % might still be suitable as rayon-grade pulps. Increasing extraction temperature lowered the xylan content at which cellulose yield started to decrease. Furthermore, at any given xylan content, increasing extraction temperature resulted in cellulosic pulp with higher degree of polymerization. The extracted xylan was recovered almost quantitatively as xylo-oligosaccharides. The results suggest that HWEs at elevated temperatures may be applied to purify cellulosic pulps, preferably containing a low xylan content, and to recover the extracted sugars.     

Improvement of derivatized amino acid detection sensitivity in micellar electrokinetic capillary chromatography by means of acid-induced pH-mediated stacking technique

Derivatization is a frequently used sample preparation procedure applicable to the enhancement of analyte detection sensitivity. Amino acids mostly require derivatization prior to electrophoretic or chromatographic analysis, especially if spectrophotometric detection is used. This study presents an on-line preconcentration technique for derivatized amino acids. The sensitivity of the method was improved by the utilization of the proposed acid-induced pH-mediated stacking mechanism. The method is demonstrated by preconcentration of amino acids labeled with 2,4-dinitrofluorobenzene. Use of optimized conditions for a large sample volume injection (40 s, 13.8 kPa) followed by electrokinetic injection of 0.1 M HCl (20 s, 10 kV) gave a 20- to 30-fold enhancement of sensitivity. The significance of the sweeping mechanism and pseudo-isotachophoresis for the on-line sample focusing and the influence of parameters on the preconcentration process were discussed. The applicability of the elaborated method was demonstrated using human urine samples.     

Heterologous Expression and Characterization of an Acidic GH11 Family Xylanase from <Emphasis Type="Italic">Hypocrea orientalis</Emphasis>

A gene encoding glycoside hydrolase family 11 xylanase (HoXyn11B) from Hypocrea orientalis EU7–22 was expressed in Pichia pastoris with a high activity (413 IU/ml). HoXyn11B was partly N-glycosylated and appeared two protein bands (19–29 kDa) on SDS-PAGE. The recombinant enzyme exhibited optimal activity at pH 4.5 and 55 °C, and retained more than 90% of the original activity after incubation at 50 °C for 60 min. The determined apparent K _m and V _max values using beechwood xylan were 10.43 mg/ml and 3246.75 IU/mg, respectively. The modes of action of recombinant HoXyn11B on xylo-oligosaccharides (XOSs) and beechwood xylan were investigated by thin-layer chromatography (TLC), high-performance liquid chromatography (HPLC), and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS), which indicated that the modes of action of HoXyn11B are different from HoXyn11A since it is able to release a significant amount of xylose from various substrates. This study provides an opportunity to better understand the hydrolysis mechanisms of xylan by xylanases from Trichoderma.     

A Mathematical Analysis of the Selective Enrichment of NECEEM-Based Non-SELEX

Non-Systematic Evolution of Ligands by EXponential enrichment (SELEX)selection of aptamers, a novel technology for aptamer selection from libraries of random DNA (or RNA) sequences, involves repetitive steps of partitioning without polymerase chain reaction (PCR) amplification between them. This selection is based on non-equilibrium capillary electrophoresis of equilibrium mixtures (NECEEM) and has exceptionally high efficiency. In this paper, a mathematical analysis was carried out to predict the levels of enrichment of non-SELEX selection under different conditions such as different protein concentrations and different efficiencies of partitioning. Investigated results suggest that the magnitude of the bulk affinity (k _d) being 10⁴ or 10⁵ μM for the initial pool has no obvious effect on selective enrichment and that the first, second, and third rounds of non-SELEX selection have different optimum protein concentration values [T _f] that give maximum enrichment levels when [T _f] ranges from 0.0005 to 0.5 μM. The significance of analyzing selective enrichment of NECEEM-based non-SELEX with the efficiency of partitioning target-bound ligands from free ligands has been demonstrated.     

Synthesis and properties of metal clusters in polymeric matrices

A one-step plasma deposition process is described which allows the uniform dispersion of small metal clusters throughout a thin film polymer matrix. Plasma parameters and plasma gas phase diagnostics relevant to the control of film composition and structure are discussed. Chemical and structural analytical techniques such as I.R. absorption spectroscopy, E.S.C.A., Auger electron spectroscopy, X-ray fluorescence, X-ray and electron diffraction and microscopy are used to characterize the cluster containing films. Changes in cluster size and shape as a function of volume fraction and as a result of post deposition annealing are described. Optical and electrical properties are presented below and above the onset of percolation and are evaluated in terms of contemporary effective medium theories.     

Uncertainty measurement for automated macro program-processed quantitative proton NMR spectra

The evaluation of a fully automated quantitative proton nuclear magnetic resonance spectroscopy (qNMR) processing program, including the determination of its processing uncertainty, and the calculations of the combined uncertainty of the qNMR result, is presented with details on the use of a trimmed purity average. Quantitative NMR spectra (1359) were collected over a 4-month period on various concentrations of pseudoephedrine HCl dissolved in D₂O (0.0610 to 93.60 mg/mL) containing maleic acid (the internal standard) to yield signal-to-noise ratios ranging from 3 to 72,000 for analyte integral regions. The resulting 5436 purities exhibited a normal distribution about the best estimate of the true value. The median absolute deviation (MAD) statistical method was used to obtain a model of uncertainty relative to the signal-to-noise of the analyte’s integral peaks. The model was then tested using different concentrations of known purity chloroquine diphosphate. qNMR results of numerous illicit heroin HCl samples were compared to those obtained by capillary electrophoresis. Graphical Abstract

?     

Thermal evaluation of heavy crude oil by simultaneous TG-DSC-FTIR: Part 2

In this work a continuous investigation of the thermal behavior of two heavy crude oils, P2 and P4, from Brazilian basin was performed using simultaneous technique TG-DSC-FTIR. In previous publication—Part 1, about these same oils at nitrogen atmosphere, it was identified for P2 sample that the main evolved component was 1-dodecyl-4-octyl-cyclohexane at 450 °C and for P4 sample the main component was evolved at 340 °C referent to 1-methyl cyclohexene. The simultaneous technique TG/FTIR was also performed for the present study in synthetic air atmosphere and was more elucidative than analysis in nitrogen atmosphere. For heavy oil P2, there was identified the presence of carbon dioxide, carbon monoxide and 4-methylcyclohexanone at 382 °C. Whilst for sample P4 the gaseous components evolved at 454 °C were carbon dioxide, carbon monoxide and 1-methylcyclohexene. Also differences in TG analysis for both samples were observed regarding the number of components. In air atmosphere crude oil P2 exhibited three decomposition stages, in nitrogen were only two. Four stages were exhibited on the thermogravimetric curve for oil P4 in synthetic air, while in nitrogen atmosphere there were three stages. Thus, this study has a unique character regarding the use of combined simultaneous techniques as STA/FTIR to identify components in heavy oil which may contribute to upgrade methods referring to crude oil composition.     

Synthesis,characterization and self-assembly of amphiphilic block copolymer poly(4-vinyl benzene chloride)-b-poly(N-vinylpyrrolidone) in aqueous solution

The synthesis, characterization and self-assembly of a novel amphiphilic block copolymer containing a poly(N-vinylpyrrolidone) as a segment of hydrophilic and poly(4-vinyl benzene chloride) (PVBC) arms are reported. The copolymer was characterized by FT-IR spectroscopy ¹H NMR. The composition and the molecular weights of the block copolymers were established using gel permeation chromatography and ¹H NMR. The water-soluble fraction of poly(N-vinyl-2-pyrrolidone) (PVP)/PVBC block copolymers formed micelles which were investigated at 25 °C in water at 5 mg/ml concentration using a tensiometer. The morphology of micelles in aqueous solution was determined by the AFM, SANS, and SAXS methods.     

Quantitative characterization by asymmetrical flow field-flow fractionation of IgG thermal aggregation with and without polymer protective agents

Complexes formed between poly(acrylates) and polyclonal immunoglobulin G (IgG) in its native conformation and after heat stress were characterized using asymmetric flow field-flow fractionation (AF4) coupled with on-line UV-Vis spectroscopy and multi-angle light-scattering detection (MALS). Mixtures of IgG and poly(acrylates) of increasing structural complexity, sodium poly(acrylate) (PAA), a sodium poly(acrylate) bearing at random 3 mol % n-octadecyl groups, and a random copolymer of sodium acrylate (35 mol %), N-n-octylacrylamide (25 mol %) and N-isopropylacrylamide (40 mol %), were fractionated in a sodium phosphate buffer (0.02 M, pH 6.8) in the presence, or not, of 0.1 M NaCl. The AF4 protocol developed allowed the fractionation of solutions containing free poly(acrylates), native IgG monomer and dimer, poly(acrylates)/IgG complexes made up of one IgG molecule and a few polymer chains, and/or larger poly(acrylates)/IgG aggregates. The molar mass and recovery of the soluble analytes were obtained for mixed solutions of poly(acrylates) and native IgG and for the same solutions incubated at 65 °C for 10 min. From the combined AF4 results, we concluded that in solutions of low ionic strength, the presence of PAA increased the recovery ratio of IgG after thermal stress because of the formation of electrostatically-driven PAA/IgG complexes, but PAA had no protective effect in the presence of 0.1 M NaCl. Poly(acrylates) bearing hydrophobic groups significantly increased IgG recovery after stress, independently of NaCl concentration, because of the synergistic effect of hydrophobic and electrostatic interactions. The AF4 results corroborate conclusions drawn from a previous study combining four analytical techniques. This study demonstrates that AF4 is an efficient tool for the analysis of protein formulations subjected to stress, an important achievement given the anticipated important role of proteins in near-future human therapies. ?