Crystal growth,quality characterization and THz properties of DAST crystals

4‐N, N‐diethylamino‐4’‐N’‐methyl‐stilbazolium tosylate (DAST) crystals were grown by slope nucleation method (SNM). The crystal structure of grown DAST crystals was characterized by single crystal X‐ray diffraction with demonstrating X‐ray diffraction main peaks. The crystal defects were analyzed by the synchrotron radiation X‐ray topography. It was found that the unbalanced temperature gradient, the Teflon groove and the super saturation fluctuation were primary causes of crystal defects. Furthermore, widely tunable THz waves ranging from 1.16 to 16.71 THz were generated from 1 mm‐thick DAST crystal using the optical parametric oscillator (OPO). It was obtained that the THz output energy was 27.4 nJ (peak power of 2.74 W) and the highest conversion efficiency was 1.37 × 10⁻⁵ at 3.8 THz.     

Growth and magnetic‐optical properties of Sr3Gd(BO3)3 and Sr3TbxGd1‐x(BO3)3 single crystals

Single crystals of Sr₃Gd(BO₃)₃ (SGB) and Sr₃Tb_xGd_1‐x(BO₃)₃ (TSGB) with dimension Ø 20 mm×20 mm have been grown by Czochralski method. The grown crystals were characterized by X‐ray powder diffraction analysis which showed the crystals belong to hexagonal structure with lattice parameters of a=b=1.254 nm, c=0.926 nm (SGB) and a=b=1.253 nm, c=0.925 nm (TSGB). In TSGB, x=17.7% was obtained by X‐ray fluorometry which showed the segregation coefficient of Tb is closed to 1. The transmission spectrum was measured, which indicated the crystals have high transmittance in 400‐1100 nm region. The Faraday rotation of single crystals at 532 nm wavelength was measured at room temperature. Finally, the Verdet constants were investigated, (SGB) V=17.9 degcm^‐1T^‐1 and (TSGB) V=21.3 degcm^‐1T^‐1. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and optoelectrical properties of Ga‐doped ZnO semiconductor thin films grown by magnetron sputtering

Transparent conductive gallium‐doped zinc oxide (Ga‐doped ZnO) films were prepared on glass substrate by magnetron sputtering. The influence of substrate temperature on structural, optoelectrical and surface properties of the films were investigated by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), spectrophotometer, four‐point probe and goniometry, respectively. Experimental results show that all the films are found to be oriented along the c‐axis. The grain size and optical transmittance of the films increase with increasing substrate temperature. The average transmittance in the visible wavelength range is above 83% for all the samples. It is observed that the optoelectrical property is correlated with the film structure. The Ga‐doped ZnO film grown at the substrate temperature of 400 °C has the highest figure of merit of 1.25 × 10⁻² Ω⁻¹, the lowest resistivity of 1.56 × 10⁻³ Ω·cm and the highest surface energy of 32.3 mJ/m².     

Growth and characterization of 4‐Aminopyridinium‐4‐nitro phenolate single crystals

Organic optical material 4‐Aminopyridinium‐4‐nitro phenolate (4AP4NP) has been synthesized, and single crystals of size 20 x 14 x 6 mm³ have been grown from acetone solvent at room temperature by solvent evaporation technique. The grown crystals have been characterized by X‐ray diffraction to determine the cell parameters, and by FT‐IR technique to confirm the formation of the expected compound. The crystal belongs to monoclinic crystal system with space group P2₁/a.The structural perfection of the grown crystals has been analyzed by high‐resolution X‐ray diffraction (HRXRD) rocking curve measurements. The thermal stability of the compound has been determined by TG‐DTA curves. The transmittance of 4AP4NP has been used to determine the refractive index n; the extinction coefficient K and both the real ε_r and imaginary ε_i components of the dielectric constant as functions of photon energy. The optical band gap of 4AP4NP is 2.4 eV. The dielectric and mechanical behavior of the specimen was also studied. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Single‐crystal sapphire microstructure for high‐resolution synchrotron X‐ray monochromators

We report on the growth and characterization of sapphire single crystals for X‐ray optics applications. Structural defects were studied by means of laboratory double‐crystal X‐ray diffractometry and white‐beam synchrotron‐radiation topography. The investigations confirmed that the main defect types are dislocations. The best quality crystal was grown using the Kyropoulos technique. Therein the dislocation density was 10²–10³ cm⁻² and a small area with approximately 2*2 mm² did not show dislocation contrast in many reflections. This crystal has suitable quality for application as a backscattering monochromator. A clear correlation between growth rate and dislocation density is observed, though growth rate is not the only parameter impacting the quality.     

Preparation,physicochemical and third order nonlinear optical properties of bis(tetrabutylammonium)bis(2‐thioxo‐1,3‐dithiole‐4,5‐dithiolato)mercurate(II)

Bis(tetrabutylammonium)bis(2‐thioxo‐1,3‐dithiole‐4,5‐dithiolato)mercurate(II) was prepared and characterized by elemental analyses, electronic absorption, infrared and X‐ray powder diffraction spectroscopy. The specific heat of the crystal was measured to be 1878.2 J.mol^–1K^–1 at 300 K. The thermal decomposition process was investigated by means of thermogravimetric analysis and differential thermal analysis measurements in air together with infrared and X‐ray powder diffraction spectra. The third‐order nonlinear optical properties at 800 nm were measured by femtosecond optical Kerr gate technique by using CS₂ as reference. The third‐order optical susceptibility of its acetone solution at the concentration of 9.27 × 10^–4 M was obtained to be 2.53 × 10^–14 esu. The second‐order hyperpolarizability was estimated to be 1.7 × 10^–32 esu and the response time was about 226 fs. The third order nonlinear optical properties at 532 nm were investigated by using the Z‐scan technique with 20 ps. It exhibited self‐focusing effect and saturable absorption. The second molecular hyperpolarizability was estimated to be 8.4 × 10^–32 esu. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Surfactant directed synthesis of mesoporous alumina and α‐alumina single crystal

Mesoporous Al₂O₃ were positively synthesized via treatment of the freshly precipitated amorphous alumina gel using aluminium sulphate as aluminium source, and sodium dodecyl sulphate (SDS) as structure‐directing agent (SDAs). The microstructures, morphologies and textural properties of the as‐prepared materials were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM) and thermo gravimetric analysis (TG‐DTA). The calcined product at 600 °C was highly porous in nature having a BET surface area of 42 m²/g. These porous Al₂O₃ exhibits excellent adsorption performance for Congo red and the corresponding decolourisation efficiencies reached 99% in just 15 min at 27 °C. The subsequent calcined product at 1200 °C is the alpha alumina single crystal hexagonal platelets with rhombohedral crystallization.     

A hexagonal columnar packing structure of C7 symmetric supramolecules: a superstructure of a 2:3 complex of heptakis‐(6‐O‐tert‐butyldimethylsilyl)‐β‐cyclodextrin and ethyl acetate

The recrystallization of Heptakis[6‐O‐tert ‐butyldimethylsilyl)]‐β ‐cyclodextrin ( 1 ) from ethyl acetate gave single crystals of 1 ₂·(ethyl acetate)₃ complex. The superstructure of 1₂·(ethyl acetate)₃ complex was investigated by ¹H NMR spectroscopy, molecular modeling, and single crystal/powder X‐ray diffractions. Encapsulation of ethyl acetate molecules with 1 and a unique hexagonal columnar superstructure in its crystal were found. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth and characterization of ferroelectric‐ferroelastic Tb2(MoO4)3 crystals

Transparent and nearly colorless ferroelectric‐ferroelastic β′‐Tb₂(MoO₄)₃ (TMO) single crystals have been grown by the Czochralski (CZ) method. The single crystal structure was investigated by X‐ray powder diffraction and was shown to be a single phase with the structure similar as the β′‐Gd₂(MoO₄)₃ crystal. The optical transparency of the TMO crystal has been measured and the crystal is almost transparent in the visible and near infrared regions. The defects of TMO crystal were evaluated by etching technique and the ferroelectric domain structures were observed by an optical microscope. A high‐resolution X‐ray diffraction analysis demonstrates that the as‐grown TMO crystal possesses relatively high optical quality. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical,mechanical and thermal properties of p‐bromoacetanilide

Solubility and metastable zonewidth were estimated for p‐Bromoacetanilide. Employing slow evaporation method crystals of size 22x17x6 mm³ and 38x25x10 mm³ were grown at a constant temperature of 40°C and room temperature respectively from methanol solution. The cell dimensions were obtained by single crystal X‐ray diffraction study. The placement of protons was identified from NMR spectral analysis. UV‐Visible and fluorescence spectral analyses were carried out for the grown crystals. Vickers microhardness test was performed on the prominent (110) of the as grown crystal. Thermogravimetric and differential scanning calorimetric studies were carried out to determine the thermal properties of the grown crystal. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal structure of N‐[(1Z)‐1‐(3‐methyl‐3‐phenylcyclobutyl)‐2‐thiomorpholin‐4‐ylethylidene] thiourea

The crystal structure of N‐[(1Z)‐1‐(3‐methyl‐3‐phenylcyclobutyl)‐2‐thiomorpholin‐4‐ylethylidene] thiourea (C₁₈H₂₆N₄S₂) has been determined by X‐ray crystallographic techniques. The compound crystallizes in the orthorhombic space group Pbca, with unit cell parameters: a = 15.692(3), b = 20.803(8), c = 11.979(6)Å, Z = 8, V = 3911(7)ų. The crystal structure was solved by direct methods and refined by full‐matrix least squares to a final R‐value of 0.084 for 1447 observed reflections [I > 2σ ( I ) ]. In the thiosemicarbazide moiety, the S = C bond length is 1.656(6), N‐C‐N angle is 115.6(5)°. The crystal structure is stabilized by the intermolecular N‐H...S hydrogen bonds. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal structure,spectroscopic studies and non‐linear optical properties of 2‐amino‐3‐nitropyridinium trichloroacetate

A new quadratic nonlinear optical crystal, 2‐amino‐3‐nitropyridinium trichloroacetate (2A3NPTCA), was synthesized and the single crystals were grown by slow evaporation method at room temperature. Single crystal X‐ray diffraction and powder X‐ray diffraction experiments were carried out in order to confirm the structure and crystalline nature of 2A3NPTCA crystal. The chemical bonding and various functional groups present in the 2A3NPTCA were identified from FT‐IR spectrum. The UV–visible–NIR transmission spectrum shows that it is suitable for frequency‐converting in the wavelength region of 431–1200 nm. Thermogravimetric (TG) and differential thermal analysis (DTA) were carried out to characterize the thermal behaviors of the grown crystals. Kurtz and Perry powder method for second harmonic generation (SHG) measurements demonstrate that 2A3NPTCA is a phase matching material and its nonlinear optical efficiency is two times that of KDP. All the above results suggest that 2A3NPTCA is a potential candidate of NLO material.     

*Ir4+ ion‐free 12CaO·7Al2O3 single crystal grown by the CZ method

Ir⁴⁺ ion‐free 12CaO•7Al₂O₃ (C12A7) single crystals that were colorless and transparent have been grown by the CZ method under 0.5% oxygen‐containing nitrogen atmospheres for the first time. Powder X‐ray diffraction patterns and X‐ray single‐crystal diffraction were used to investigate the microstructure and quality of the C12A7 single crystal. The results show that the crystal was a C12A7 single crystal with tetragonal symmetry. The content of Ir⁴⁺ in the C12A7 single crystal was tested by ICP along with visible‐light transmittance. There was no Ir⁴⁺ in the C12A7 crystal grown in a 0.5% oxygen‐containing nitrogen atmosphere. Contents of Ir⁴⁺ in C12A7 crystal grown under 1% and 2% oxygen‐containing nitrogen atmospheres were 500 ppm and 400 ppm, respectively. The microstructure of C12A7 single crystal was determined by the content of oxygen in the growth process: the occurrence of bubbles and color increase when the content of oxygen is increased. Bubbles and color decrease when the oxygen content is lowered, bubbles disappeared and the color of C12A7 turns into transparent when the content of oxygen is 0.5%, the C12A7 phase decomposed when the content of oxygen was lower than 0.5%. So, the content of oxygen was responsible for the bubbles, color and cracking, and these also can be limited by controlling the content of oxygen.     

Growth and characterization of magneto‐optical YFeO3 crystals

The floating zone growth of magneto‐optical crystal YFeO₃ has been investigated. The polycrystalline feed rod was prepared by a pressure of 250MPa and sintering at about 1500°C. A crack‐ free YFeO₃ single crystal has been successfully grown. The crystal preferred to crystallize along <100> direction with about 10° deviation. The X‐ray rocking curve of the crystal has a FWHM of 24 arcsec, confirming the high crystal quality of the sample. The (100) plane was etched by hot phosphoric acid and the dislocation density was about 10⁴/cm². A thin outer layer with Y₂O₃‐rich composition was found at the periphery of as‐grown crystals, which was attributed to the Fe₂O₃ evaporation during growth. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal and molecular structure of 3‐phenyl‐4‐(p‐chlorobenzylamino)‐4,5‐dihydro‐1‐H‐1,2,4‐triazol‐5‐on

The structure of the title compound, C₁₅H₁₃N₄OCl was determined by single crystal X‐ray diffraction technique. The structure consists of a p‐chlorobenzylamino moiety and triazol and phenyl rings. The title compound crystallizes in the monoclinic space group P2₁/c with a = 14.368(3), b = 6.255(3), c = 17.631(3) Å, β = 113.24(3)°, Z = 4, V = 1455.8(8) ų and D_x = 1.372 gcm^‐3. The structure was solved by direct methods and refined by full‐matrix least‐squares method (R=0.0477). The dihedral angle between the triazole moiety and the phenyl ring is 28.8(3)°. The molecular packing is stabilized by N‐H…N and N‐H…O types of inter molecular hydrogen bonds. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural and morphological studies on Mn substituted ZnO nanometer‐sized crystals

Mn substituted ZnO nanocrystals synthesized by a co‐precipitation method. X‐ray diffraction (XRD) studies confirms the presence of wurtzite (hexagonal) crystal structure similar to un doped ZnO, suggesting that doped Mn ions go at the regular Zn sites. The lattice parameters a and c are increasing with increasing Mn content. The unit cell volume increases with increasing Mn concentration, indicating the homogeneous substitution of Mn²⁺ for the Zn²⁺. The lattice distortion parameter (ε_v) is evaluated from XRD data and found that it enhances as Mn content increases. Transmission electron microscopy photographs show that the size of the ZnO crystals is in the range of 20‐50 nm. The SAED pattern confirms the hexagonal and crystalline nature of the samples which are in agreement with X‐ray analysis. The chemical groups of the samples have been identified by FTIR studies (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal structure of 4‐(1‐methyl‐1‐mesitylcyclobutane‐3‐yl)‐2‐aminothiazole

The crystal structure of 4‐(1‐methyl‐1‐mesitylcyclobutane‐3‐yl)‐2‐aminothiazole (C₁₇H₂₂N₂S₁) has been determined by X‐ray crystallographic techniques. The compound crystallizes in the triclinic space group P‐1 with Z = 6. The crystal structure was solved by direct methods and refined by full‐matrix least squares to a final R‐value of 0.052 for 2298 observed reflections [I > 2σ ( I ) ]. There are three crystallographically independent molecules, I, II and III. These molecules are held together by intermolecular N‐H...N hydrogen bonds. © 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim     

Crystal and molecular structure of 1‐allyl‐5‐(4‐methylbenzoyl)‐4‐(4‐methylphenyl)pyrimidine‐2(1H)‐thione

The crystal structure of 1‐allyl‐5‐(4‐methylbenzoyl)‐4‐(4‐methylphenyl)pyrimidine‐2(1H)‐thione (C₂₂H₂₀N₂OS) has been determined from three dimensional single crystal X‐ray diffraction data. The title compound crystallizes in the monoclinic space group P 2₁/c, with a = 10.6674(13), b = 10.1077(7), c = 17.9467(19) Å, β = 98.460(9)°, V = 1914.0(3) ų, D_calc = 1.251 g cm^–3, Z = 4. In the title compound, the allyl group shows positional disorder. Molecules are linked by C‐H···O, C‐H···N and C‐H···S intermolecular interactions forming two‐dimensional network. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation,single crystal growth and characterization of bis(tetrabutylammonium)bis(4,5‐dithiolato‐1,3‐dithiole‐2‐thione)copper

The preparation and single crystal growth of bis(tetrabutylammonium)bis(4,5‐dithiolato‐1,3‐dithiole‐2‐thione)copper, (I), are described. The energy gap Eg of (I) is about 2.38 eV. The nonlinear optical susceptibility χ⁽³⁾ is about 1.3×10^‐3 esu at 1064 nm. The characterization of (I) has been performed by electronic absorption, infrared and X‐ray powder diffraction spectroscopy. The thermal behavior of (I) has been investigated by means of thermogravimetric analysis (TGA) and differential thermal analysis (DTA) measurements in air. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Photoacoustic studies on the thermal properties of the NLO compound: L‐alaninium maleate

Studies on thermal and optical properties are very essential for a nonlinear optical material. Photoacoustics (PA) is a recently developed non‐destructive testing (NDT) tool for studying such properties. L‐Alaninium maleate (C₃H₈NO₂⁺·C₄H₃O₄^‐), an organic non‐linear optical (NLO) material was synthesized using submerged seed solution method and was characterized by single crystal X‐ray diffraction (XRD) and density. PA technique was used to determine the thermal parameters of LAM crystals. Moreover, possible phase transition analysis was conducted to ascertain the thermal stability. Scanning electron microscopic (SEM) studies were also carried out and crystal‐packing features discussed. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)