Voltammetry determination of trace manganese with pretreatment glassy carbon electrode by linear sweep voltammetry

This paper described the determination of trace manganese using linear sweep voltammetry at a pretreatment glassy carbon electrode. The glassy carbon electrode pretreated by electrochemical method in the 0.1 mol l⁻¹ NaOH solution greatly improved the electrode responsibility in the determination of manganese(II). The barrier to the detection of low manganese concentration was overcome by means of autocatalytic effect of manganese oxide deposited on the electrode in advance. Under the optimum experiments condition (0.04 mol l⁻¹ NH₃-NH₄Cl buffer solution, pH 9.0), the linear range was 4×10⁻⁸ to 1×l0⁻⁶ mol l⁻¹ Mn(II) for linear sweep voltammetry and 1×10⁻⁹ to 4×10⁻⁸ mol l⁻¹ Mn(II) for convolution voltammetry. The relative standard deviation for 2×10⁻⁸ mol l⁻¹ Mn(II) is 3.4%. The proposed method is simple, rapid, sensitive and selective. It had been applied to the determination of trace manganese in samples with satisfactory results.     

Electrochemical behavior of atomoxetine and its voltammetric determination in capsules

In this work, the electrochemical behavior and the analytical application of atomoxetine, a selective noradrenaline reuptake inhibitor, are studied. Atomoxetine, studied by differential pulse voltammetry and cyclic voltammetry on a glassy carbon electrode, exhibited an anodic response in aqueous media with pH between 1.5 and 7. In non-aqueous medium (acetonitrile), the drug exhibited two irreversible oxidation peaks that are diffusion controlled. From chronocoulometric studies in acetonitrile, it was determined that each oxidation signal involves two and four electrons, respectively. For analytical purposes, a differential pulse voltammetry technique in 0.1 mol L⁻¹ perchloric acid was selected, which exhibited adequate figures of merit. The percent recovery was 96.6 ± 1.2 and the detection and quantitation limits were 6.9 × 10⁻⁵ and 1.0 × 10⁻⁴ mol L⁻¹, respectively. Also, results indicate that excipients do not interfere with the oxidation signal of atomoxetine, which leads to the conclusion that the developed method is satisfactorily selective for atomoxetine quantification in pharmaceuticals with no prior separation or extraction necessary. Finally, the proposed voltammetric method was successfully applied to both the assay and the uniformity content of atomoxetine in capsules. For comparison, high-performance liquid chromatography analysis was also performed.     

Langmuir-Blodgett film of p-tert-butylthiacalix[4]arene modified glassy carbon electrode as voltammetric sensor for the determination of Hg(II)

The π-A isotherms and UV-vis spectra of the transferred films suggested that the monolayer of p-tert-butylthiacalix[4]arene can coordinate with Hg²⁺ at the air-water surface. From these observations, a glassy carbon electrode coated with Langmuir-Blodgett film of p-tert-butylthiacalix[4] arene as a new voltammetric sensor is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode and modified glassy carbon electrode using direct coating method, the Langmuir-Blodgett film-modified electrode can greatly improve the measuring sensitivity of Hg²⁺. Under the selected conditions, the Langmuir-Blodgett film-modified electrode in 0.1 mol L⁻¹ H₂SO₄ + 0.01 mol L⁻¹ KCl solution shows a linear voltammetric response for Hg²⁺ in the range of 5.0 × 10⁻¹⁰ to 1.5 × 10⁻⁷ mol L⁻¹, with a detection limit of 2.0 × 10⁻¹⁰ mol L⁻¹. The proposed method was also applied to determine Hg²⁺ in water samples (tap, lake and river water). In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility and good stability.     

Electrochemical analysis of methylparathion pesticide by a gemini surfactant-intercalated clay-modified electrode

In this study, an hybrid material obtained by the intercalation of a gemini surfactant between the layers of smectite-type clay, was fully characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR) and N₂ adsorption-desorption experiments (BET method). To ascertain the intercalation process of the starting clay by the dimeric surfactant, the permselectivity and ion exchange properties of the organoclay were investigated by ion exchange voltammetry using [Fe(CN)₆]³⁻ and [Ru(NH₃)₆]³⁺ as redox probes, by the means of a clay film-modified electrode. Due to its organophilic character, the surfactant-intercalated complex was evaluated as electrode modifier for the accumulation of methylparathion (MP) pesticide. The electroanalytical procedure involves two steps: preconcentration under open-circuit followed by voltammetric detection by square wave voltammetry: the peak current obtained (after 5 min preconcentration in 4 × 10⁻⁵ mol L⁻¹ MP) on a glassy carbon electrode coated by a thin film of the modified clay was more than five times higher than that exhibited by the same substrate covered by a film of the pristine clay. This opens the way to the development of a sensitive method for the detection of the pesticide. Many parameters that can affect the stripping response (surfactant loading of the hybrid material, film composition, pH of the detection medium, preconcentration time, electrolysis potential and duration as well as some other instrumental parameters) were systematically investigated to optimize the sensitivity of the organoclay-modified electrode. After optimization, a linear calibration curve for MP was obtained in the concentration range from 4 × 10⁻⁷ to 8.5 × 10⁻⁶ mol L⁻¹ in acetate buffer (pH 5), with a detection limit of 7 × 10⁻⁸ mol L⁻¹ (signal-to-noise ratio equal to 3). The interference effect of various inorganic ions likely to influence the stripping determination of the pesticide was also examined, and the described method was applied to spring water analysis.     

Sensitive voltammetric determination of baicalein at DNA Langmuir-Blodgett film modified glassy carbon electrode

The present paper describes to modify a double stranded DNA-octadecylamine (ODA) Langmuir-Blodgett film on a glassy carbon electrode (GCE) surface to develop a voltammetric sensor for the detection of trace amounts of baicalein. The electrode was characterized by atomic force microscopy (AFM) and cyclic voltammetry (CV). Electrochemical behaviour of baicalein at the modified electrode had been investigated in pH 2.87 Britton-Robinson buffer solutions by CV and square wave voltammetry (SWV). Compared with bare GCE, the electrode presented an electrocatalytic redox for baicalein. Under the optimum conditions, the modified electrode showed a linear voltammetric response for the baicalein within a concentration range of 1.0 × 10⁻⁸-2.0 × 10⁻⁶ mol L⁻¹, and a value of 6.0 × 10⁻⁹ mol L⁻¹ was calculated for the detection limit. And the modified electrode exhibited an excellent immunity from epinephrine, dopamine, glucose and ascorbic acid interference. The method was also applied successfully to detect baicalein in the medicinal tablets and spiked human blood serum samples with satisfactory results.     

Voltammetric study on the complex of thiram-copper(II) and its application

Based on the formation of tetramethylthiuram disulfide (thiram)-copper(II) complex by square-wave voltammetry on a glassy carbon electrode, a new method is proposed for determination of thiram. There is a good linear relationship between peak current and concentration of thiram in the range of  mol l⁻¹ (r=0.999). The method is applied to the determination of thiram residue in plant with satisfactory results, compared with results achieved by using HPLC. Two oxidation peaks and two reduction peaks are obtained by cyclic voltammetry on a glassy carbon electrode in 0.2 mol l⁻¹ HAc-NaAc (pH 4.0) solution containing thiram-copper(II) complex. The electrode reaction process is quasi-reversible with adsorptive characteristics. The mechanism of electrode reaction is discussed.     

Electrochemical determination of iodide on a vanadium oxide-polypropylene carbonate coated glassy carbon electrode

A vanadium oxide-modified glassy carbon electrode was simply and conveniently fabricated by casting vanadium tri(isoproxide) oxide (VO(OC₃H₇)₃) and poly(propylene carbonate) (PPC) onto the glassy carbon electrode surface. The electrochemical properties of iodide at the VO(OC₃H₇)₃-PPC film-modified glassy carbon electrode were investigated by cyclic voltammetry, and an anodic peak was observed at approximately +0.71 V (vs. SCE). Based on this, a sensitive and convenient electrochemical method was proposed for the determination of iodide. Flow injection amperometry (FIA) exhibited a good linear relationship with the concentration of iodide in the range of 5 × 10⁻⁷ mol L⁻¹ and 1 × 10⁻³ mol L⁻¹, and the detection limit was 1 × 10⁻⁷ mol L⁻¹. Quantitative recovery of iodide in synthetic samples has been obtained and the interferences from different cations and anions have been studied. The method has been successfully applied to the determination of iodide in dry edible seaweed. The concentrations of iodide measured by this method are in good agreement with those obtained by spectrophotometric method.     

Simultaneous determination of N-acetyl-p-aminophenol and p-aminophenol with poly(3,4-ethylenedioxythiophene) modified glassy carbon electrode

A sensitive and selective method was developed for the determination of N-acetyl-p-aminophenol (APAP) and p-aminophenol (PAP) using poly(3,4-ethylenedioxythiophene) (PEDOT)-modified glassy carbon electrode (GCE). Cyclic voltammetry and differential pulse voltammetry were used to investigate the electrochemical reaction of APAP and PAP at the modified electrode. Both APAP and PAP showed quasireversible redox reactions with formal potentials of 367 mV and 101 mV (vs. Ag/AgCl), respectively, in phosphate buffer solution of pH 7.0. The significant peak potential difference (266 mV) between APAP and PAP enabled the simultaneous determination both species based on differential pulse voltammetry. The voltammetric responses gave linear ranges of 1.0 × 10⁻⁶-1.0 × 10⁻⁴ mol L⁻¹ and 4.0 × 10⁻⁶-3.2 × 10⁻⁴ mol L⁻¹, with detection limits of 4.0 × 10⁻⁷ mol L⁻¹ and 1.2 × 10⁻⁶ mol L⁻¹ for APAP and PAP, respectively. The method was successfully applied for the determination of APAP and PAP in pharmaceutical formulations and biological samples.     

A novel poly(cyanocobalamin) modified glassy carbon electrode as electrochemical sensor for voltammetric determination of peroxynitrite

This report described the direct voltammetric detection of peroxynitrite (ONOO⁻) at a novel cyanocobalamin modified glassy carbon electrode prepared by electropolymeriation method. The electrochemical behaviors of peroxynitrite at the modified electrode were studied by cyclic voltammetry. The results showed that this new electrochemical sensor exhibited an excellent electrocatalytic activity to oxidation of peroxynitrite. The mechanism of catalysis was discussed. Based on electrocatalytic oxidation of peroxynitrite at the poly(cyanocobalamin) modified electrode, peroxynitrite was sensitively detected by differential pulse voltammetry. Under optimum conditions, the anodic peak current was linear to concentration of peroxynitrite in the range of 2.0 × 10⁻⁶ to 3.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1.0 × 10⁻⁷ mol L⁻¹ (S/N of 3). The proposed method has been applied to determination of peroxynitrite in human serum with satisfactory results. This poly(cyanocobalamin) modified electrode showed high selectivity and sensitivity to peroxynitrite determination, which could be used in quantitative detection of peroxynitrite in vivo and in vitro.     

Voltammetric determination of food colorants using a polyallylamine modified tubular electrode in a multicommutated flow system

This work describes the construction of a polyallylamine modified tubular glassy carbon electrode and its application in the electroreduction of food azo colorants (tartrazine, sunset yellow and allura red) by square wave voltammetry. The electrode modification prevented the surface fouling and, simultaneously, enhanced the analytical signal intensity. The developed unit was coupled to a multicommutated flow system which, given the complexity of samples, was designed to allow the implementation of the standard additions method in an automatic way, using only one standard solution.The described method presented a linear range up to about 2.0 × 10⁻⁴ mol l⁻¹ for the referred colorants, with a detection limit of 1.8 × 10⁻⁶ mol l⁻¹ for tartrazine, 3.5 × 10⁻⁶ mol l⁻¹ for sunset yellow and 1.4 × 10⁻⁶ mol l⁻¹ for allura red. The method was applied in the analysis of these colorants in several food samples, and no statistically significant difference between the results obtained by the proposed and the comparative method (HPLC) was found, at a 95% confidence level. Repeatability in the analysis of samples (expressed in R.S.D.) was about 3% (n = 10).     

Voltammetric behavior of naratriptan and its determination in tablets

The electrochemical behavior and the analytical application of the selective serotonin agonist naratriptan (N-methyl-3-(1-methyl-4-piperidyl)indole-5-ethanesulfonamide) are presented herein. Naratriptan exhibits an anodic response in aqueous media over a broad pH range (pH 2-12), as determined by differential pulse voltammetry and cyclic voltammetry using glassy carbon electrodes. This response is irreversible in nature, diffusion-controlled and probably caused by the oxidation of the naratriptan indole moiety. The differential pulse voltammetry technique was performed in 0.1 mol L⁻¹ Britton-Robinson buffer (pH = 3), which elicited the most reproducible results. The percentage of naratriptan recovery was 102.1 ± 1.8%, and the limits of detection and quantitation were 9.5 × 10⁻⁶ and 2.0 × 10⁻⁵ mol L⁻¹, respectively. Selectivity trials revealed that the oxidation signal of the drug was not disturbed by the presence of excipients or degradation products. Thus, we conclude that the method presented herein is useful for the quantification of naratriptan in pharmaceutical drugs and that this method requires no separations or extractions. Finally, this voltammetric method was successfully applied to determine the quantity and the content uniformity of naratriptan in drug tablets. A comparison of this technique to the standard high-performance liquid chromatography technique was conducted at the end of our study.     

Electrocatalytic oxidation behavior of guanosine at graphene, chitosan and Fe3O4 nanoparticles modified glassy carbon electrode and its determination

A graphene, chitosan and Fe₃O₄ nanoparticles (nano-Fe₃O₄) modified glassy carbon electrode (graphene-chitosan/nano-Fe₃O₄/GCE) was fabricated. The modified electrode was characterized by scanning electron microscope and electrochemical impedance spectroscopy. The electrochemical oxidation behavior of guanosine was investigated in pH 7.0 phosphate buffer solution by cyclic voltammetry and differential pulse voltammetry. The experimental results indicated that the modified electrode exhibited an electrocatalytic and adsorptive activities towards the oxidation of guanosine. The transfer electron number (n), transfer proton number (m) and electrochemically effective surface area (A) were calculated. Under the optimized conditions, the oxidation peak current was proportional to guanosine concentration in the range of 2.0 × 10⁻⁶ to 3.5 × 10⁻⁴ mol L⁻¹ with the correlation coefficient of 0.9939 and the detection limit of 7.5 × 10⁻⁷ mol L⁻¹ (S/N = 3). Moreover, the modified electrode showed good ability to discriminate the electrochemical oxidation response of guanosine, guanine and adenosine. The proposed method was further applied to determine guanosine in spiked urine samples and traditional Chinese medicines with satisfactory results.     

Electrochemical determination of maltol in beverages with glassy carbon electrode and its silica sol-gel modified electrode

The electrochemical behavior of maltol on a glassy carbon (GC) electrode was investigated. The results were applied to differential pulse voltammetric determination of maltol in beverages pretreated by ultrafiltration. Under the optimum experimental conditions, the linear range is 1×10⁻⁵ to 6×10⁻⁴ mol l⁻¹ maltol and the relative standard deviation for 0.4 mmol l⁻¹ maltol is 0.6% (n=9). The detection limit was 5 μmol l⁻¹. Furthermore, silica sol-gel film on GC electrode could be used as suitable selective membrane, which integrated selective membrane on the electrode and substituted for the pretreatment of ultrafiltration. Under the above conditions, maltol was determined by semi-differential linear sweep voltammetry at a silica sol-gel modified GC electrode in the concentration range of 5×10⁻⁶ to 5×10⁻⁴ mol l⁻¹. The detection limit was 2 μmol l⁻¹ and the relative standard deviation for 0.1 mmol l⁻¹ maltol was 0.7% (n=7). The proposed method is of sensitivity, simplicity, rapidness and no contamination. It had been applied to the direct determination of maltol in beverages such as grape wines, drinks and beers without any pretreatment. The results obtained with the present method were satisfactory with those obtained by spectrophotometry. It could be used as a simple and practical method for the determination of the flavor enhancer maltol in beverages.     

Quantitative determination of zinc in milkvetch by anodic stripping voltammetry with bismuth film electrodes

Bismuth film electrode (BiFE) was shown to be an attractive alternative to common mercury film electrode (MFE) for anodic stripping voltammetric measurements. In this study, bismuth film, that was in situ deposited onto glassy carbon electrode, was used to detect zinc content of milkvetch, used in traditional Chinese medicine. Variables affecting the response have been evaluated and optimized. Experimental results showed a high response, with a good linearity (between 0.5 × 10⁻⁶ mol L⁻¹ and 3 × 10⁻⁶ mol L⁻¹) a good precision (R.S.D. = 3.58%) and a low detection limit (9.6 × 10⁻⁹ mol L⁻¹ with a 120 s anodic). The anodic stripping performance makes the bismuth film electrode very desirable for measurements of trace nutritive element zinc in milkvetch and should impart possible restrictions on the use of mercury electrode.     

A new dodecylsulfate-selective supported liquid membrane electrode based on its N-cetylpyridinium ion-pair

A supported liquid and a poly(vinyl chloride) (PVC)-based membrane selective for dodecylsulfate (DS⁻) ion are described. The active element is a membrane containing a dissolved ion association complex of DS⁻ with cetylpyridinium (CP⁺) cation. The supported liquid membrane electrode (acetophenone as solvent) showed a Nernstian response towards the DS⁻ anion over the concentration range of sodium dodecylsulfate (SDS) from 8.3×10⁻³ to 1.0×10⁻⁶ mol dm⁻³ at 25 °C. The proposed electrode also showed a super-Nernstian potential response (108±2 mV decade⁻¹) at low concentrations (1.0×10⁻⁹ to 1.0×10⁻⁶ mol dm⁻³). Moreover, this electrode showed good selectivity and precision (R.S.D.?2.0%), and was usable within the pH range 4.0-6.8. The proposed electrode revealed a lower limit of detection of 6.3×10⁻⁷ mol dm⁻³ and improved selectivity in comparison with the some previously reported DS⁻ ion selective electrodes. The isothermal temperature coefficient of this electrode amounted to −0.001 V °C⁻¹. The liquid membrane electrode may find application in the direct determination of SDS by the standard addition method at pH 5.0, and in the physicochemical studies of surfactant solutions.     

The petentiometric determination of peroxide hydrogen and glucose on the glassy electrode modified by the calix[4]arene

A new petentiometric method to determine peroxide hydrogen and glucose had been studied. This method had been applied on the petentiometric determination of peroxide hydrogen and glucose in the total ionic strength adjustment buffer (TISAB) (pH 7.5) solution with the glassy electrode modified by the calix[4]arene. The glassy carbon electrode covered with the calix[4]arene depended on the H₂O₂ concentration in the range of log[H₂O₂] from −3.3 to −1.2 in the solution of TISAB (pH 7.5) with nearly Nernstian slope of about 65.6 ± 3 mV and the detection limit of peroxide hydrogen was 4.0 × 10⁻⁵ mol L⁻¹. The glassy carbon electrode covered with the calix[4]arene depended on the glucose concentration in the range of log[glucose] from −3.6 to −2.8 in the solution of TISAB (pH 7.5) with nearly Nernstian slope of about 50.2 ± 2 mV and the detection limit of glucose was 2.0 × 10⁻⁵ mol L⁻¹. The electrode had the good selectivity, sensitivity, stability and repeatability.     

Catalytic-adsorptive stripping voltammetric determination of ultra-trace iridium(III). Application to fresh- and sea-water

An extremely sensitive stripping voltammetric procedure for ultra-trace determination of iridium(III) is reported. The method is based on the interfacial accumulation of the iridium(III)-CTAB complex onto the glassy carbon electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. 0.3 mol L⁻¹ acetate buffer pH 4.7 + 6.9 × 10⁻² mol L⁻¹ NaBrO₃ + 2.7 × 10⁻⁵ mol L⁻¹ cetyltrimethylammonium bromide (CTAB) + 0.2 mol L⁻¹ KCl was employed as the supporting electrolyte.The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403 and Fresh Water NIST-SRM 1643d.The accuracy, expressed as relative error e%, was satisfactory, being lower than 6%, while precision as repeatability, expressed as relative standard deviation s_r%, was generally lower than 5%. The limit of detection was of the order of 2-3 ng L⁻¹.Once set up on the standard reference materials, the analytical procedure was transferred and applied to superficial water sampled in proximity to superhighway and in the Po river mouth area.     

Electrical detection of deoxyribonucleic acid hybridization based on carbon-nanotubes/nano zirconium dioxide/chitosan-modified electrodes

A novel and sensitive electrochemical DNA biosensor based on nanoparticles ZrO₂ and multi-walled carbon nanotubes (MWNTs) for DNA immobilization and enhanced hybridization detection is described. The MWNTs/nano ZrO₂/chitosan-modified glassy carbon electrode (GCE) was fabricated and oligonucleotides were immobilized to the GCE. The hybridization reaction on the electrode was monitored by differential pulse voltammetry (DPV) analysis using electroactive daunomycin as an indicator. Compared with previous DNA sensors with oligonucleotides directly incorporated on carbon electrodes, this carbon nanotube-based assay with its large surface area and good charge-transport characteristics increased DNA attachment quantity and complementary DNA detection sensitivity. The response signal increases linearly with the increase of the logarithm of the target DNA concentration in the range of 1.49 × 10⁻¹⁰ to 9.32 × 10⁻⁸ mol L⁻¹ with the detection limit of 7.5 × 10⁻¹¹ mol L⁻¹ (S/N = 3). The linear regression equation is I = 32.62 + 3.037 log C_DNA (mol L⁻¹) with a correlation coefficient value of 0.9842. This is the first application of carbon nanotubes combined with nano ZrO₂ to the fabrication of an electrochemical DNA biosensor with a favorable performance for the rapid detection of specific hybridization.     

Direct electrochemical determination of carbaryl using a multi-walled carbon nanotube/cobalt phthalocyanine modified electrode

The electrochemical detection of carbaryl at low potentials, in order to avoid matrix interferences, is an important challenge. This study describes the development, electrochemical characterization and utilization of a glassy carbon (GC) electrode modified with multi-wall carbon nanotubes (MWCNT) plus cobalt phthalocyanine (CoPc) for the quantitative determination of carbaryl in natural waters. The surface morphology was examined by scanning electron microscopy, enhanced sensitivity was observed with respect to bare glassy carbon and electrocatalytic effects reduced the oxidation potential to +0.80 V vs. SCE in acetate buffer solution at pH 4.0. Electrochemical impedance spectroscopy was used to estimate the rate constant of the oxidation process and square-wave voltammetry to investigate the effect of electrolyte pH. Square-wave voltammetry in acetate buffer solution at pH 4.0, allowed the development of a method to determine carbaryl, without any previous step of extraction, clean-up, or derivatization, in the range of 0.33-6.61 μmol L⁻¹, with a detection limit of 5.46 ± 0.02 nmol L⁻¹ (1.09 ± 0.02 μg L⁻¹) in water. Natural water samples spiked with carbaryl and without any purification step were successfully analyzed by the standard addition method using the GC/MWCNT/CoPc film electrode.     

Determination of sub-micromolar amounts of sulfide by standard free anodic stripping voltammetry and anodic stripping voltammetric titration

A novel electrochemical methods namely standard free anodic stripping voltammetry and anodic stripping voltammetric titration are proposed for determination of dissolved sulfide concentration. 2Ag⁺ + S²⁻ → Ag₂S reaction is used to provide the information. The anodic stripping voltammetric response of unreacted silver-ions at the glassy carbon electrode is used as analytical signal. Results reliability and accuracy are confirmed by analysis of model solutions, spiked natural and tap waters and recovery study, with a recovery of 100 ± 5% (n = 7) obtained. The approaches show the detection limit (3σ_blank) of 2-5 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of 2-5% for repeated measurements.