Conductivity, dielectric behaviour and thermal stability studies of lithium ion dissociation in poly(methyl methacrylate)-based gel polymer electrolytes

Thin films of poly(methyl methacrylate) (PMMA) with lithium triflate (LiCF₃SO₃) were prepared by using the solution-casting method with PMMA as the host polymer. Ionic conductivity and dielectric measurements were carried out on these films. The highest conductivity for polymer electrolyte with a ratio of 65:35 was found to be 9.88 × 10⁻⁵ S cm⁻¹, which is suitable for the production of mobile phone battery. Thermal gravimetric analysis was carried out to evaluate the thermal stability of the polymer electrolyte. The addition of salts will increase thermal stability of the polymer electrolyte.     

A comparative study of lithium and sodium salts in PAN-based ion conducting polymer electrolytes

The conducting polymer electrolyte films consisting of polyacrylonitrile (PAN) as the host polymer, lithium triflate (LiCF₃SO₃) and sodium triflate (NaCF₃SO₃) as inorganic salts were prepared by the solution-cast technique. The pure PAN film was prepared as a reference. The ionic conductivity for the films is characterized using impedance spectroscopy. The room temperature conductivity for the PAN + 26 wt.% LiCF₃SO₃ film and the PAN + 24 wt.% NaCF₃SO₃ film is 3.04 × 10⁻⁴ S cm⁻¹ and 7.13 × 10⁻⁴ S cm⁻¹, respectively. XRD studies show that the complexation that has occurred in the PAN containing salt films and complexes formed are amorphous. The FTIR spectra results confirmed the complexation has taken place between the salt and the polymer. These results correspond with surface morphology images obtained from SEM analysis. The conductivity–temperature dependence of the highest conducting film from PAN + LiCF₃SO₃ and PAN + NaCF₃SO₃ systems follows Arrhenius equation in the temperature range of 303 to 353 K. The PAN containing 24 wt.% LiCF₃SO₃ film has a higher ionic conductivity and lower activation energy compared to the PAN containing 26 wt.%LiCF₃SO₃ film. These results can be explained based on the Lewis acidity of the alkali ions, i.e., the interaction between Li⁺ ion and the nitrogen atom of PAN is stronger than that of Na⁺ ion.     

Impedance and FTIR studies on plasticized PMMA–LiN(CF<Subscript>3</Subscript>SO<Subscript>2</Subscript>)<Subscript>2</Subscript> nanocomposite polymer electrolytes

Plasticized polymer electrolytes composed of poly(methyl methacrylate) (PMMA) as the host polymer and lithium bis(trifluoromethanesulfonyl)imide LiN(CF₃SO₂)₂ as a salt were prepared by solution casting technique at different ratios. The ionic conductivity varied slightly and exhibited a maximum value of 3.65 × 10⁻⁵ S cm⁻¹ at 85% PMMA and 15% LiN(CF₃SO₂)₂. The complexation effect of salt was investigated using FTIR. It showed some simple overlapping and shift in peaks between PMMA and LiN(CF₃SO₂)₂ salt in the polymer electrolyte. Ethylene carbonate (EC) and propylene carbonate (PC) were added to the PMMA–LiN(CF₃SO₂)₂ polymer electrolyte as plasticizer to enhance the conductivity. The highest conductivities obtained were 1.28 × 10⁻⁴ S cm⁻¹ and 2.00 × 10⁻⁴ S cm⁻¹ for EC and PC mixture system, respectively. In addition, to improve the handling of films, 1% to 5% fumed silica was added to the PMMA–LiN(CF₃SO₂)₂–EC–PC solid polymer electrolyte which showed a maximum value at 6.11 × 10⁻⁵ S cm⁻¹ for 2% SiO₂.     

Transport properties of hexanoyl chitosan-based gel electrolyte

Films of hexanoyl chitosan-based polymer electrolyte were prepared by the technique of solution casting. The effect of plasticizer on the transport properties of hexanoyl chitosan:lithium trifluoromethanesulfonate (LiCF₃SO₃) electrolytes have been investigated. The plasticizer used was ethylene carbonate (EC). The highest room temperature conductivity achieved in the EC-plasticized hexanoyl chitosan-based electrolytes is 2.75×10⁻⁵ S cm⁻¹. The Rice and Roth model was used to explain the variations in the dc conductivity observed. The exponent, s, in Jonscher’s universal power law equation σ(ω)=σ _dc+Aω ^s , was analyzed as a function of temperature for the sample containing 30 wt% of EC. The analysis suggests that the conduction mechanism follows that proposed by the overlapping large polaron tunneling model.     

Effect of ZnO nanoparticles filler concentration on the properties of PEO-ENR50-LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript> solid polymeric electrolyte

A solid polymer electrolyte comprising blend of poly(ethylene oxide) and 50% epoxidized natural rubber (ENR50) as a polymer host, LiCF₃SO₃ as a salt and nanoparticle ZnO as an inorganic filler was prepared by solution-casting technique. The effect of filler on the electrolyte properties was characterized and analysed. FESEM analysis showed that the filler was well distributed in the polymer matrix, while the effective interaction between the salt and the polymer host was reduced by the addition of filler. As evidenced by FTIR analysis, which showed the formation of triplet peak at C-O-C stretching region. Ionic conductivity was found to decrease from 1.4 × 10⁻⁴ Scm⁻¹ to 2.5 × 10⁻⁶ Scm⁻¹ upon the addition of filler, due to the blocking effect of filler into the electrolyte conduction pathways. The temperature dependence on the electrolyte conductivity obeys Arrhenius rule in two temperature regions.     

Morphology,chemical interaction,and conductivity of a PEO-ENR50 based on solid polymer electrolyte

A solid polymer electrolytes (SPE) comprising blend of poly(ethylene oxide; PEO) and epoxidized natural rubber as a polymer host and LiCF₃SO₃ as a dopant were prepared by solution-casting technique. The SPE films were characterized by field emission scanning electron microscopy to determine the surface morphology, X-ray diffraction, and differential scanning calorimeter to determine the crystallinity and thermogravimetric analysis to confirm the mass decrease caused by loss of the solvent. While the presence of the complexes was investigated by reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Electrochemical impedance spectroscopy was conducted to obtain ionic conductivity. Scanning electron microscopy analysis showed that a rough surface morphology of SPE became smoother with addition of salt, while ATR-FTIR spectroscopy analysis confirmed the polymer salt complex formation. The interaction occurred between the salt, and ether group of polymer host where the triple peaks of ether group in PEO merged and formed one strong peak at 1,096 cm⁻¹. Ionic conductivity was found to increase with the increase of salt concentration in the polymer blend complexes. The highest conductivity achieved was 1.4 × 10⁻⁴ Scm⁻¹ at 20 wt.% of LiCF₃SO₃, and this composition exhibited an Arrhenius-like behavior with the activation energy of 0.42 eV and the preexponential factor of 1.6 × 10³ Scm⁻¹.     

Structure,thermal properties,conductivity and electrochemical stability of di-urethanesil hybrids doped with LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>

Variable chain length di-urethane cross-linked poly(oxyethylene) (POE)/siloxane hybrid networks were prepared by application of a sol-gel strategy. These materials, designated as di-urethanesils (represented as d-Ut(Y′), where Y′ indicates the average molecular weight of the polymer segment), were doped with lithium triflate (LiCF₃SO₃). The two host hybrid matrices used, d-Ut(300) and d-Ut(600), incorporate POE chains with approximately 6 and 13 (OCH₂CH₂) repeat units, respectively. All the samples studied, with compositions ∞ > n ≥ 1 (where n is the molar ratio of (OCH₂CH₂) repeat units per Li⁺), are entirely amorphous. The di-urethanesils are thermally stable up to at least 200 °C. At room temperature the conductivity maxima of the d-Ut(300)- and d-Ut(600)-based di-urethanesil families are located at n = 1 (approximately 2.0 × 10⁻⁶ and 7.4 × 10⁻⁵ Scm⁻¹, respectively). At about 100 °C, both these samples also exhibit the highest conductivity of the two electrolyte systems (approximately 1.6 × 10⁻⁴ and 1.0 × 10⁻³ Scm⁻¹, respectively). The d-Ut(600)-based xerogel with n = 1 displays excellent redox stability.     

Studies of structure, thermal, and electrical properties for Cs 5 H 3 (SO 4 ) 4 crystal

Electrical conductivity, differential scanning calorimetry, and X-ray diffraction measurements were performed on a pentacesium trihydrogen tetrasulfate, Cs₅H₃(SO₄)₄, crystal. The transition entropy at a superionic phase transition and the activation energy of proton migrations in the superionic phase were determined to be 58.2 J K⁻¹ mol⁻¹ and 0.48 eV, respectively. The crystal structure of Cs₅H₃(SO₄)₄ at room temperature was refined. The electrical conduction in Cs₅H₃(SO₄)₄ was discussed with the refined structure.     

Investigation of dibutyl phthalate as plasticizer on poly(methyl methacrylate)–lithium tetraborate based polymer electrolytes

Polymer electrolyte membranes, comprising of poly(methyl methacrylate) (PMMA), lithium tetraborate (Li₂B₄O₇) as salt and dibutyl phthalate (DBP) as plasticizer were prepared using a solution casting method. The incorporation of DBP enhanced the ionic conductivity of the polymer electrolyte. The polymer electrolyte containing 70 wt.% of poly(methyl methacrylate)–lithium tetraborate and 30 wt.% of DBP presents the highest ionic conductivity of 1.58 × 10⁻⁷ S/cm. The temperature dependence of ionic conductivity study showed that these polymer electrolytes obey Vogel–Tamman–Fulcher (VTF) type behaviour. Thermogravimetric analysis (TGA) was employed to analyse the thermal stability of the polymer electrolytes. Fourier transform infrared (FTIR) studies confirmed the complexation between poly(methyl methacrylate), lithium tetraborate and DBP.     

Combined effect of CuO nanofillers and DBP plasticizer on ionic conductivity enhancement in the solid polymer electrolyte PEO–LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>

We report a new kind of polyethylene oxide, PEO–LiCF₃SO₃-based composite polymer electrolyte, containing active copper oxide (CuO) nanoparticles with dibutyl phthalate (DBP) prepared by solution-cast technique. The incorporation of 10 wt.% DBP and 5 wt.% CuO to the salted polymer showed a significant conductivity enhancement with maximum conductivity 2.62 × 10⁻⁴ Scm⁻¹ at room temperature. This could be attributed to the increasing of amorphous phase content and structural changes in the polymer electrolyte. Arrhenius plot suggest that temperature-dependent conductivity is a thermally activated process.     

Electrochemical studies on polymer electrolytes based on poly(methyl methacrylate)-grafted natural rubber for lithium polymer battery

MG30 is natural rubber grafted with 30% poly(methyl methacrylate). Gel polymer electrolytes containing MG30–LiCF₃SO₃–X (X = propylene carbonate, ethylene carbonate) are prepared by solution casting technique. The polymer–salt complexes were investigated using Fourier-transformed infrared. The ionic conductivity of the electrolytes are determined by the ac impedance studies over the temperature range of 303–383 K and is observed to obey the Vogel–Tamman–Fulcher (VTF) rule. The Li⁺ transference number obtained using the Bruce and Vincent method is <0.3. The Li/Li⁺ interface stability is established and the electrolytes were found to be able to withstand a voltage of more than 4.2 V.     

Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

Ionic conductivity studies of 49% poly(methyl methacrylate)-grafted natural rubber-based solid polymer electrolytes

The potential of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a solid polymer electrolyte film in rechargeable batteries system were explored. The flat, thin, and flexible films were prepared by solution casting technique. The ionic conductivity was investigated by alternating current impedance spectroscopy. The highest conductivity of 2.3 × 10⁻⁷ Scm⁻¹ was obtained at 20wt.% of LiBF₄ salts content, while 4.0 × 10⁻⁸ Scm⁻¹ was obtained at 15wt.% LiClO₄ salts loading. The observation on structure performed by X-ray diffraction shows the highest conductivity appears at amorphous phase.     

The effects of ceramic fillers on the PMMA-based polymer electrolyte systems

The effects of ceramics fillers on the polymethylmethacrylate (PMMA)-based solid polymer electrolytes have been studied using ac impedance spectroscopy and infrared spectroscopy. The polymer film samples were prepared using solution cast technique, tetrahydrofuran (THF) used as a solvent, and ethylene carbonate (EC) has been used as plasticizer. Lithium triflate salt (LiCF₃SO₃) has been incorporated into the polymer electrolyte systems. Two types of ceramic fillers, i.e., SiO₂ and Al₂O₃, were then implemented into the polymer electrolyte systems. The solutions were stirred for several hours before it is poured into petri dishes for drying under ambient air. After the film has formed, it was transferred into desiccator for further drying before the test. From the observation done by impedance spectroscopy, the room temperature conductivity for the highest conducting film from the (PMMA–EC–LiCF₃SO₃) system is 1.36 × 10⁻⁵ S cm⁻¹. On addition of the SiO₂ filler and Al₂O₃ filler, the conductivity are expected to increase in the order of ∼10⁻⁴ S cm⁻¹. Infrared spectroscopy indicates complexation between the polymer and the plasticizer, the polymer and the salts, the plasticizer and the salts, and the polymer and the fillers. The interactions have been observed in the C=O band, C–O–C band, and the O–CH₃ band. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7-9, 2006.     

Electrochemical study of P(VDF-HFP)/PMMA blended polymer electrolyte with high-temperature stability for polymer lithium secondary batteries

In the present study, a kind of solid polymer electrolyte (SPE) based on poly(vinylidene difluoride-co-hexafluoropropylene)/poly(methyl methacrylate) blends was prepared by a casting method to solve the safety problem of lithium secondary batteries. Owing to being plasticized with a room temperature ionic liquid, N-butyl-N′-methyl-imidiazolium hexafluorophosphate, the obtained SPE shows a thermal decomposition temperature over 300°C and an ionic conductivity close to 10⁻³ S cm⁻¹. The SPE-3 sample, in which the weight of two polymers is equivalent, possesses an ionic conductivity of 0.45 × 10⁻³ S cm⁻¹ at 25°C and presents an electrochemical window of 4.43 V. The ionic conductivity of the SPE-3 is as high as 1.73 × 10⁻³ S cm⁻¹ at 75°C approaching to that of liquid electrolyte. The electrochemical performances of the Li/LiFePO₄ cells confirmed its feasibility in lithium secondary batteries.     

FTIR spectra of plasticized high molecular weight PVC–LiCF3SO3 electrolytes

Fourier transform infrared spectroscopy studies have been conducted to investigate the interaction among components in a system of high molecular weight polyvinylchloride (PVC)–lithium trifluoromethanesulfonate (LiCF₃SO₃) incorporated with different type of plasticizers, namely, ethylene carbonate (EC), propylene carbonate (PC), and dibutylphthalate (DBP). Interaction between PVC and LiCF₃SO₃ was confirmed by C–H rocking mode at 1,255 cm⁻¹ for PVC shift to 1,252 cm⁻¹ in PVC–LiCF₃SO₃. The plasticizers’ carbonyl (C=O) oxygen atom which carries lone pair electrons interact with Li⁺ of LiCF₃SO₃ and methine hydrogen of PVC in LiCF₃SO₃–plasticizer system and PVC–plasticizer system, respectively. Changes in peaks assigned to 1,264 cm⁻¹ (ν _as(SO₃)), 1,033 cm⁻¹ (ν _s(SO₃)), 1,181 cm⁻¹ (ν _as(CF₃)), 1,230 cm⁻¹ (ν _s(CF₃)), 765 cm⁻¹ (δ _s(CF₃)), 644 cm⁻¹ (δ _s(SO₃)), 578 cm⁻¹ (δ _as(CF₃)), and 519 cm⁻¹ (δ _as(SO₃)) indicate the occurrence of complexation in the PVC–LiCF₃SO₃ system, LiCF₃SO₃–plasticizer system, and PVC–LiCF₃SO₃–plasticizer system.     

Grafted natural rubber-based polymer electrolytes: ATR-FTIR and conductivity studies

Attenuated total reflectance–Fourier transformed infrared spectroscopy measurement is employed to study the interactions between the components of 30% methyl-grafted natural rubber (MG30), lithium trifluromethanesulfonate (LiCF₃SO₃ or LiTF), and propylene carbonate (PC). Vibrational spectra data of LiTF reveals that the ν_s(SO₃) at 1,045 cm⁻¹, δ_s(CF₃) at 777 cm⁻¹, and C=O stretching mode at 1,728 cm⁻¹ for MG30 have shifted to lower wave numbers in MG30–LiTF complexes indicating that complexation has occurred between MG30 and LiTF. The solvation of lithium ion is manifested in Li⁺ ← O=C interaction as shown by the downshifting and upshifting of C=O mode at 1,788 to 1,775 cm⁻¹ and ν_as(SO₃) at 1,250 to 1258 cm⁻¹, respectively, in LiTF–PC electrolytes. There is no experimental evidence of the interaction between MG30 and PC. Competition between MG30 and PC on associating with lithium ion is studied, and the studies show that the interaction between MG30–LiTF is stronger than that of the PC–LiTF in plasticized polymer–salt complexes. The effect of PC on the ionic conductivity of the MG30–LiTF system is explained in terms of the polymer, plasticizer, and salt interactions. The temperature dependence of conductivity of the polymer films obeys the Vogel–Tamman–Fulcher relation. Values of conductivity and activation energy of the MG30-based polymer electrolyte systems are presented and discussed.     

Preparation and characterization of PVAc–PMMA-based solid polymer blend electrolytes

In the present work, a novel blend polymer electrolyte membrane using poly(vinyl acetate) (PVAc), poly(methyl methacrylate) (PMMA), and lithium per chlorate (LiClO₄) in different compositions has been prepared by the solution-casting technique. Their chemical, structural characters, thermal behavior, surface morphology, and ionic conductivity were studied using Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric/differential thermal analyzer, scanning electron microscopy, and AC impedance analyzer, respectively. A maximum ionic conductivity value of 1.67 × 10⁻⁴ S/cm at 303 K is obtained for PVAc–PMMA–LiClO₄ complexes in the ratio of 25 × 75, keeping LiClO₄ constant as 10 wt.% among all the compositions studied.     

Ionic transport, thermal, XRD, and phase morphological studies on LiCF3SO3-based PVC–PVdF gel electrolytes

The plasticized polymer electrolyte composed of polyvinylchloride (PVC) and polyvinylidene fluoride (PVdF) as host polymer, the mixture of ethylene carbonate and propylene carbonate as plasticizer, and LiCF₃SO₃ as a salt was studied. The effect of the PVC-to-PVdF blend ratio with the fixed plasticizer and salt content on the ionic conduction was investigated. The electrolyte films reveal a phase-separated morphology due to immiscibility of the PVC with plasticizer. Among the three blend ratios studied, 3:7 PVC–PVdF blend ratio has shown enhanced ionic conductivity of 1.47 × 10⁻⁵ S cm⁻¹ at ambient temperature, i.e., the ionic conductivity decreased with increasing PVC-to-PVdF ratio and increased with increasing temperature. A temperature dependency on ionic conductivity obeys the Arrhenius behavior. The melting endotherms corresponding to vinylidene (VdF) crystalline phases are observed in thermal analysis. Thermal study reveals the different levels of uptake of plasticizer by VdF crystallites. The decrease in amorphousity with increase in PVC in X-ray diffraction studies and larger pore size appearance for higher content of PVC in scanning electron microscopy images support the ionic conductivity variations with increase in blend ratios.     

Conductivity studies of starch-based polymer electrolytes

A proton-conducting polymer electrolyte based on starch and ammonium nitrate (NH₄NO₃) has been prepared through solution casting method. Ionic conductivity for the system was conducted over a wide range of frequency between 50 Hz and 1 MHz and at temperatures between 303 K and 373 K. Impedance analysis shows that sample with 25 wt.% NH₄NO₃ has a smaller bulk resistance (R _b) compared to that of the pure sample. The amount of NH₄NO₃ was found to influence the proton conduction; the highest obtainable room temperature conductivity was 2.83 × 10⁻⁵ S cm⁻¹, while at 100 °C, the conductivity in found to be 2.09 × 10⁻⁴ S cm⁻¹. The dielectric analysis demonstrates a non-Debye behavior. Transport parameters of the samples were calculated using the Rice and Roth model and thus shows that the increase in conductivity is due to the increase in the number of mobile ions.