快速溶剂萃取-离子色谱法同时测定塑料中的三价铬和六价铬

建立了采用快速溶剂萃取-离子色谱同时测定塑料中三价铬和六价铬的方法。三价铬和六价铬分别以吡啶-2,6-二羧酸(PDCA)和1,5-二苯卡巴肼(DPC)作为络合剂在柱前和柱后进行衍生化,分别在紫外和可见波长下采用紫外检测器进行检测,灵敏度高,基体干扰小。本方法对三价铬和六价铬的检出限分别为5.0 μg/L和0.5 μg/L;分别在50～1000 μg/L和5.0～100 μg/L范围内呈现良好的线性关系,线性相关系数分别为0.9994和0.9998;三价铬和六价铬的回收率范围为90.7%～101.1%,相对标准偏差(RSD)为1.7%～4.4%。该方法分析速度快、灵敏度高、重现性好,可用于塑料中三价铬和六价铬的同时测定。     

Chromium(VI) transport through the Raipore 1030 anion exchange membrane

The flat sheet Raipore R1030 anion exchange membrane has been evaluated as a sample interface in an optical sensor for Cr(VI) monitoring. The R1030 is an anion exchange membrane containing quaternary ammonium groups. The Donnan dialysis (DD) that takes place has been enhanced with facilitated transport of Cr(VI) anions by using a 1,5-diphenylcarbazide (DPC) solution as stripping phase. The DPC acts as a reducing reagent for Cr(VI), and as a complexing reagent for the generated Cr(III). The Cr(III) complex is a strongly absorbing species, and this is the basis of the optical detection. The effect of chemical parameters on Cr(VI) transport has been evaluated. Experiments with UV-VIS detection have shown that the membrane R1030-DPC system exhibits features suitable for Cr(VI) optical sensing. A simplified model based on a kinetic approach is reported describing the transport mechanism of the chemically facilitated DD process.     

Chemically selective membrane optode for Cr(VI) determination in aqueous samples

A methodology for simultaneous preconcentration and determination of Cr(VI) from aqueous samples was developed using a membrane optode formed by physical inclusion of a Cr(VI) selective chromophore 1,5-diphenylcarbazide (DPC) into a plasticized cellulose triacetate matrix. The inclusion of an anion exchanger (Aliquat-336) was found to be effective for immobilization of both DPC and Cr(VI)-DPC complex in the optode matrix itself. The proportionality in intensity of the magenta color on the optodes loaded with varying amounts of Cr(VI) suggests its potential applications for screening of Cr(VI) in aqueous samples by visual colorimetry. On loading high amounts of Cr(VI) in the membrane optode, its color changes from magenta to yellow, which indicates the possibility of using it as a threshold detector for Cr(VI). The membrane optode was optimized in terms of obtaining maximum preconcentration efficiency for Cr(VI) and subsequent stable optical response proportional to the amount of Cr(VI) in the membrane optode sample. The membrane optodes were tested for Cr(VI) determination in tap water and seawater samples. Using this optode, Cr(VI) even at levels of 13.6 ppb could be quantitatively detected. The optodes developed in the present work were found to be stable, cost effective, easy to prepare and efficient for direct preconcentration and determination of Cr(VI) in a variety of aqueous samples using spectrophotometry. However, this membrane optode is for one time use only as the reaction of Cr(VI) with DPC is irreversible.     

水溶液中六价铬在碳纳米管上的吸附

针对用碳纳米管对水溶液中六价铬的吸附净化进行了研究, 考察了溶液浓度、溶液pH值、共存的三价铬离子等因素对吸附行为的影响. 实验结果表明, 碳纳米管在室温下对于六价铬的吸附量随着平衡浓度的增大而升高, 在铬浓度为493.557 mg•L−1时碳纳米管吸附量达到最大值为532.215 mg•g−1; 六价铬的浓度在300~700 mg•L−1的范围内, 碳纳米管对铬的吸附量变化不大；大于700 mg•L−1时, 随着铬的平衡浓度的升高碳纳米管对铬的吸附量降低, 铬浓度为961.074 mg•L−1时, 碳纳米管吸附量降至194.631 mg•g−1. 在pH值为2~7的范围内, 碳纳米管对六价铬的吸附量随着溶液pH值的减小而增大; 而在碱性条件下, pH值对碳纳米管吸附六价铬的影响不大. 溶液中存在三价铬时, 碳纳米管对六价铬的吸附量明显降低, 表明三价铬与六价铬有竞争吸附. 此外, 活性炭的对比吸附实验表明, 在低浓度时, 譬如在六价铬浓度为190 mg•L−1吸附时, 碳纳米管对铬的吸附量约为活性炭的6倍；而在高浓度下, 譬如六价铬浓度为493 mg•L−1时, 碳纳米管对铬的吸附量约为活性炭的2倍.     

Stability of fluoroquinolone antibiotics in river water samples and in octadecyl silica solid-phase extraction cartridges

Airborne particulate matter has been sampled at a location close to a metallurgical plant in North-Rhine-Westphalia, Germany, and first results on the chromium(VI) content in the collected dust are presented. A special procedure using a scrubber as sampling device was used to preserve Cr(VI) during the sampling procedure. The scrubber solution which consisted of 0.1 mol L^–1 TRIS-buffer solution was adjusted to a slightly alkaline pH of 8.6 to reduce the oxidation potential of Cr(VI) and to avoid possible oxidation of Cr(III) to Cr(VI), for example by oxygen (or ozone at ambient concentrations). After sampling Cr(VI) was pre-concentrated on an anion-exchange material and eluted with aqueous 0.6 mol L^–1 sodium perchlorate solution. After elution, a species-selective complex of Cr(VI) with diphenylcarbazide (DPC) was prepared; this was extracted into n-hexanol and quantified by UV–visible spectrophotometry. A detection limit of 0.9 ng m^–3 for Cr(VI) in ambient aerosols can be achieved with this method.     

Field speciation of chromium with a sequential injection lab-on-valve incorporating a bismuthate immobilized micro-column

A fully automated and portable analyzer for field speciation of inorganic chromium in wastewater was developed. The instrument consists of a micro-sequential injection lab-on-valve (LOV) system and a miniature USB2000 spectrophotometer. A multi-purpose flow cell was incorporated on one side of the main body of the LOV, which offers vast potentials and versatilities in its compatibility with various detection modes. On-line oxidation of trivalent chromium was performed on a bismuthate immobilized silica micro-column reactor integrated in the LOV. When determining Cr(VI), its chromogenic reaction with 1,5-diphenylcarbazide (DPC) was facilitated in the flow cell and the absorbance was monitored in situ at 548 nm via optical fibers. While for the quantification of total chromium, Cr(III) was oxidized on-line by aspirating sample solution through the oxidizing column reactor, followed by chromogenic reaction with DPC and the absorbance was monitored in the flow cell. With a sampling volume of 200 μl, the detection limits of 5.6 μg l⁻¹ for Cr(VI) and 6.8 μg l⁻¹ for total chromium were achieved along with a sampling frequency of 60 h⁻¹. A R.S.D. value of 2.0% was recorded at 32 μg l⁻¹ of Cr(VI). The practical applicability of the speciation analyzer was validated by analyzing Cr(VI) and total chromium contents in two certified reference materials. The feasibility of performing rapid field speciation of chromium in wastewater samples was also demonstrated.     

印制电路板中六价铬测定方法的研究进展

阐述了近年来国内外印制电路板中六价铬Cr(Ⅵ)的测定方法,主要包括分光光度法、柱后衍生法、离子色谱-电感耦合等离子体质谱联用(IC-ICP-MS)等方法,未来印制电路板中六价铬的测定方法一定向着新技术联用方向发展。     

Preconcentration and speciation of chromium using a melamine based polymeric sequestering succinic acid resin: its application for Cr(VI) and Cr(III) determination in wastewater

A new melamine based polymeric sequestering resin was prepared for preconcentration and separation of hexavalent chromium from water, and its sequestering action was investigated. The water-insoluble, cross-linked sequestering resin was formed by reaction with bromosuccinic acid and cross-linking of melamine. The active sequestering group on the resin is NH-(Succinic acid) or salt thereof. The resulting chelating resin was characterized by infrared spectra. The newly prepared resin quantitatively retained Cr(VI) at pH 2.0-4.0 when the flow rate was maintained between 1 and 5 ml min⁻¹. The retained Cr(VI) was instantaneously eluted with 25 ml of 0.1 M NaOH. The chromium species were determined by a flame atomic absorption spectrometer. The limits of detection for Cr(VI) and Cr(III) were found to be 5.3 and 4.2 μg l⁻¹, respectively. The precision and accuracy of the proposed procedure was checked by the use synthetic and reference steel samples. The established preconcentration method was successfully applied to the determination and selective separation of Cr(VI) in electroplating industry wastewater. Total concentrations determined by the spectrophotometric method (110.3±0.6 g l⁻¹ Cr(VI) and 1.2±0.3 g l⁻¹ Cr(III)) are compared with those found by FAAS and the obtained results (110.4±1.8 g l⁻¹ Cr(VI) and 1.4±0.5 g l⁻¹ Cr(III)) show good agreement.     

Thermal lens spectrometric determination of hexavalent chromium

The applicability of thermal lens spectrometry (TLS) for quantification and routine determination of hexavalent chromium was investigated by using a collinear dual beam thermal lens spectrometer. In aqueous solutions the LOD of 0.1 μg l⁻¹ was obtained for Cr(VI) by using 160 mW laser power. The performance of the technique was verified by the determination of hexavalent chromium in standard reference water samples (NIST SRM 1643a and NIST SRM 1643c) and comparing the results for Cr(VI) in CCA (Cr, Cu, As)-treated timber extracts to concentrations obtained by atomic absorption spectrometry (AAS). Good agreement between the TLS results and reported values for Cr(VI) in SRMs as well as AAS results for Cr(VI) in CCA-treated timbers confirmed that TLS is a reliable and accurate analytical technique applicable for the determination of Cr(VI) in aqueous solutions at concentration levels 0.5–100 μg l⁻¹.     

Determination of hexavalent chromium (Cr(VI)) in plastics using organic-assisted alkaline extraction

An organic-assisted alkaline extraction method was developed for the determination of hexavalent chromium (Cr(VI)) in plastics. The solubilization of polymer as a pre-step of the alkaline extraction provided good extraction efficiency of Cr(VI) from the sample. The optimization of the experimental conditions affecting the extraction and UV–vis spectrophotometric analysis was accomplished by evaluating the recovery rate of Cr(VI) through the analysis of Cr(VI) in in-house polymer reference materials (RMs). With the proposed method, most of the Cr(VI) in polymers was released within a short extraction time of 30 min and the Cr(III)-DPCO complex can be kept stable for 24 h. The heating for the extraction of the Cr(VI) was not necessary. The optimal pH of the final solution was fixed at 2.0. The proposed extraction method was applied successfully for the determination of Cr(III) and Cr(VI) in spiked samples. The practical applicability of this new method was evaluated through the analysis of Cr(VI) in in-house polymer RMs. The good linearity was demonstrated at desired concentrations of the range 0–3.3 mg L⁻¹. The detection limits were quite low, varying from 0.0061 to 0.0285 mg L⁻¹. The recovery of Cr(VI) was between 97 and 106%, and the relative standard deviation (R.S.D.) was below 6%.     

Flow-injection configurations for chromium speciation with a single spectrophotometric detector

The simultaneous or sequential determination of chromium(VI) and total chromium in water by flow injection analysis, using different configurations with a double- or single-beam spectrophotometer as detector, is investigated. The method is based on reaction between chromium(VI) and 1,5-diphenylcarbazide. Chromium(III) and (VI) are distinguished by using two carrier streams, one of which contains cerium(IV) to oxidize chromium(III) to chromium(VI). The determination range is 0.2–10.0 μg Cr ml^?1; the r.s.d. is 0.8% for 1 μg Cr. The sampling frequency is 40 h^?1. A wide study of interferences is reported.     

Electrophoretic separations with polyether ether ketone capillaries and capacitively coupled contactless conductivity detection

The Raipore R1030 membrane, an anion-exchange membrane containing ammonium groups as ionogenic groups, was evaluated as the interface of an optical sensor for Cr(VI), and the effect of chemical parameters affecting Cr(VI) transport were studied. Good transport features were obtained, demonstrating the suitability of the Raipore R1030 membrane for this application. Thus, an optical sensor for chromium(VI) monitoring in industrial process waters was developed. The sensor is based on the renewable reagent approach and uses the Raipore R1030 membrane as the interface between the sample and the sensor head, which contains 1,5-diphenylcarbazide as spectrophotometric reagent for chromium. Chromium(VI) crosses the membrane and reacts with the reagent inside the sensor head, resulting in changes in the absorption of light. These changes are monitored in situ through a system of optical fibers. The sensor performance was tested by analysing samples from a waste water treatment plant for effluents from electroplating industries.     

Electroanalytical Detection of Cr(VI) and Cr(III) Ions Using a Novel Microbial Sensor

A microbial sensor, namely carbon paste electrode (CPE) modified with Citrobacter freundii (Cf–CPE) has been developed for the detection of hexavalent (Cr(VI)) and trivalent (Cr(III)) chromium present in aqueous samples using voltammetry, an electroanalytical technique. The biosensor developed, demonstrated about a twofold higher performance as compared to the bare CPE for the chosen ions. Using cyclic voltammetry and by employing the fabricated Cf–CPE, the lowest limit of detection (LLOD) of 1x10⁻⁴ M and 5x10⁻⁴ M for Cr(VI) and Cr(III) ions respectively could be achieved. By adopting the Differential Pulse Cathodic Stripping Voltammetric technique, the LLOD could be further improved to 1x10⁻⁹ M and 1x10⁻⁷ M for Cr(VI) and Cr(III) ions respectively using the biomodified electrodes. The reactions occurring at the electrode surface‐chromium solution interface and the mechanisms of biosorption of chromium species onto the biosensor are discussed. The stability and utility of the developed biosensor for the analysis of Cr(VI) and Cr(III) ions in chromite mine water samples has been evaluated.     

Speciated isotope dilution analysis of Cr(III) and Cr(VI) in water by ICP-DRC-MS

An isotope dilution method has been developed for the speciation analysis of chromium in natural waters which accounts for species interconversions without the requirement of a separation instrument connected to the mass spectrometer. The method involves (i) in-situ spiking of the sample with isotopically enriched chromium species; (ii) separation of chromium species by precipitation with iron hydroxide; (iii) careful measurement of isotope ratios using an inductively coupled plasma mass spectrometer (ICP-MS) with a dynamic reaction cell (DRC) to remove isobaric polyatomic interferences. The method detection limits are 0.4 μg L⁻¹ for Cr(III) and 0.04 μg L⁻¹ for Cr(VI). The method is demonstrated for the speciation of Cr(III) and Cr(VI) in local nullah and synthetically spiked water samples. The percentage of conversion from Cr(III) to Cr(VI) increased from 5.9% to 9.3% with increase of the concentration of Cr(VI) and Cr(III) from 1 to 100 μg L⁻¹, while the reverse conversion from Cr(VI) to Cr(III) was observed within a range between 0.9% and 1.9%. The equilibrium constant for the conversion was found to be independent of the initial concentrations of Cr(III) and Cr(VI) and in the range of 1.0 (at pH 3) to 1.8 (at pH 10). The precision of the method is better than that of the DPC method for Cr(VI) analysis, with the added bonuses of freedom from interferences and simultaneous Cr(III) determination.     

Simultaneous determination of hexavalent and total chromium in water and plating baths by spectrophotometry

A new spectrophotometric determination method of hexavalent chromium in waste water and plating baths is described based on the oxidation of beryllon III by chromium(VI) in 0.02M sulphuric acid medium. The decrease in the absorbance of beryllon III was measured at 482 nm with an apparent molar absorptivity of 5.15 x 10(4)1.mole(-1).cm(-1). Beer's law was obeyed for chromium(VI) over the range 0-25 mug/25 ml. After the oxidation of Cr(III) to Cr(VI) by ammonium persulphate, total chromium can be determined. Therefore, chromium(III) can be calculated by subtracting chromium(VI) from total chromium. The detection limit is 0.015 and 0.020 mug/25 ml for chromium(VI) and total chromium, respectively. A sensitive spectrophotometric method for trace Cr(III) and Cr(VI) in waste water and plating baths was developed with good precision and accuracy. The reaction is also discussed.     

Progress on the Photocatalytic Reduction Removal of Chromium Contamination

Rapid industrialization leads to increased wastewater discharge encompassing hexavalent chromium (Cr(VI)), which leads to serious environmental problems of toxicity and potential carcinogenicity. Removal of these species is normally carried out by ion‐exchange, precipitation, membrane filtration, sorption, photocatalytic reduction, etc. This review mainly focuses on the photocatalytic and photoelectrocatalytic (PEC) reduction of Cr (VI), because of their advantages over other methods such as reduced risk of secondary pollution by non‐reduced Cr (VI), no sludge formation, no need for a large amount of chemical reagents, clean and easy installation. The main factors influencing the photocatalytic reduction efficiency of Cr (VI) such as catalyst activity, solution pH, Cr adsorption on the catalyst and additives, are briefly discussed. Finally, a special emphasis is provided to the photoelectrocatalytic (PEC) reduction of Cr (VI).     

Surfactant-promoted enhancement in bioremediation of hexavalent chromium to trivalent chromium by naturally occurring wall algae

Research on Chemical Intermediates - The discharge of hexavalent chromium [Cr(VI)] has resulted in significant pollution because of the presence of Cr(VI) oxyanions. They are highly water-soluble,...     

Spectrophotometric Determination of Chromium(VI) with Cr(VI)-o-Cl-PF–TDPC Ternary Complex after Preconcentration on an Organic Solvent-soluble Membrane Filter

Abstract

A simple and rapid preconcentration technique, based on collecting trace hexavalent chromium on an organic soluble membrane filter is described. At pH 5.0, chromium(VI), o-chlorophenyl-fluorone (o-Cl-PF) and tetradecylpyridinium chloride (TDPC) form the ternary ion-associate chelate, which can be collected on a 0.2μm nitrocellulose membrane. The filter is dissolved in a small volume of dimethyl sulfoxide (DMSO) acidified with 0.15 mL 3 mol/L sulfuric acid, and the absorbance of the resulting solution is measured at 545 nm wavelength against the reagent blank. The absorbance is proportional to the content of hexavalent chromium in the range of 0.1–1.8μg, in 5 mL solvent. The sensitivity of the ternary complex reaction is very high with molar absorptivity of 1.2 × 10⁵. A detection limit better than 0.3 μg/L can be achieved. The ions normally present in water do not interfere when mixed masking agents are added. The proposed method has been applied to the analysis of water samples from several sources, the recoveries of the hexavalent chromium added to the samples are quantitative, and results found are satisfactory.     

Reduction of hexavalent chromium at solid electrodes in acidic media: reaction mechanism and analytical applications

The electrochemical detection of hexavalent chromium species was investigated. It was found that Cr(VI) can undergo chemically irreversible reduction in acidic solutions at gold, glassy carbon and boron-doped diamond electrodes. The process was found to be diffusionally controlled at all three electrodes studied. The response obtained at a gold electrode towards the reduction of chromium(VI) produced an electrochemically reversible wave in contrast to those recorded at glassy carbon and boron-doped diamond electrodes. The analytical response of the hexavalent species was studied at gold electrodes in the presence of common environmental interferences: Ni²⁺, Cu²⁺, Fe³⁺, Cr³⁺ and Triton X-100 (surfactant), with an LoD of 4.3 μM obtained in the presence of 5 mM Cr(III).     

Utilization of Cr(VI) solutions with steel shavings

New single-stage method was developed for chemical utilization of wastewater containing 0.25 to 400 g L^–1 of chromium in terms of chromium anhydride with the us of sulfuric acid and steel cuttings. The method makes it possible to convert hexavalent chromium into easily used ferrochromium precipitates. It was found that there occur periodic synchronous concentration fluctuations of Cr(VI) and Cr(III) up to, respectively, 400 g L^–1 and 150 mg L^–1 in the course of reduction of hexavalent chromium with the use of steel cuttings in sulfuric acid solutions.