一维/二维复合碳载体组成对Pd催化剂甲醇氧化性能的影响

采用固相-液相两步混合法制备了由碳纳米管（CNTs）和石墨烯纳米片（GNPs）组成的CNTs-GNPs复合载体。以乙二醇还原法将Pd纳米粒子沉积于复合碳载体上,制得Pd/CNTs-GNPs催化剂。以透射电子显微镜、X射线衍射及X射线光电子能谱表征催化剂的形貌、组成和结构;以电化学方法考察催化剂的甲醇电氧化性能。结果表明,Pd/CNTs-GNPs（1/4）（GNPs质量分数为1/4）催化剂具有较大的电化学表面积和较高的甲醇电氧化活性,其甲醇氧化峰电流密度可达Pd/CNTs催化剂的1.97倍。催化剂的高活性得益于CNTs-GNPs载体的一维/二维复合结构使Pd纳米粒子具有良好的分散性能。计时电流实验表明,与单一载体负载Pd催化剂相比,复合载体负载Pd催化剂具有较强的抗中毒能力。     

A novel Pt/Au/C cathode catalyst for direct methanol fuel cells with simultaneous methanol tolerance and oxygen promotion

A novel Pt/Au/C catalyst was prepared by depositing the Pt and Au nanoparticles on the carbon support. The synthesized catalysts were characterized by energy-dispersive X-ray (EDX) and transmission electron microscopy (TEM), and electrochemically analyzed for activity towards oxygen-reduction reaction and methanol oxidation reaction. EDX and TEM results reveal that Pt nanoparticles supported on carbon supports were separated by Au nanoparticles. The electrochemical analysis indicate that the novel catalyst showed the enhanced methanol tolerance while maintaining a high catalytic activity for the oxygen-reduction reaction, which could be attributed to the less methanol adsorption on Pt/Au/C catalyst.     

Preparation of CoSe nanoparticles by microwave-assisted polyol method: effect of Se/Co ratio, support type and synthesis conditions on oxygen reduction activity

Highly methanol-tolerant CoSe nanoparticles supported on different carbon substrates were synthesized by microwave heating of glycerol solutions of cobalt(II) acetate and sodium selenite at different Se/Co mole ratios in the presence of different concentrations of acetic acid and ammonia. The resulting CoSe catalysts were used for the electrochemical oxygen reduction reaction (ORR) in acidic solution in the presence of methanol. The ORR activity of the catalyst was increased by increasing its Se content up to 50?mol%. The presence of acetic acid or ammonia in the synthesis solution significantly affects the electrocatalytic performance of the CoSe catalyst; highest activity was observed when the catalyst was synthesized at NH₃/Co(II) mole ratio of 6. Among the catalysts prepared on different supports including carbon black (Vulcan XC-72R), and nanoporous carbons synthesized from resorcinol-formaldehyde and phloroglucinol-formaldehyde resins, the one supported on the carbon prepared from the last resin exhibited highest electrocatalytic activity for ORR.     

碳载体的O3处理对直接甲醇燃料电池Pt-Ru/C催化剂性能的影响

为了提高直接甲醇燃料电池阳极催化剂的催化活性, 利用O₃处理的Vulcan XC-72碳黑为载体, 制备Pt-Ru/C催化剂, 并与未经处理的Vulcan XC-72为载体制备的Pt-Ru/C催化剂的性能进行比较. 采用XPS和BET测试了O₃处理后碳粉表面的含氧浓度和比表面积, 结果表明, 随处理时间延长, 碳表面含氧浓度先减少后增加, 比表面积减小; 而随着处理温度升高, 比表面积增加, 含氧浓度先减少后增加. XRD, TEM方法对催化剂的结构及形貌的表征结果表明: O₃处理的碳黑为载体制备的Pt-Ru/C催化剂粒径均匀、分散性好. 在0.5 mol/L CH₃OH和0.5 mol/L H₂SO₄溶液中, 利用粉末微电极测试了循环伏安和稳态极化曲线, 结果表明: O₃处理碳粉为载体的催化剂比未经处理的碳粉为载体的催化剂的活性高. 研究了O₃处理碳粉的时间和温度对催化剂性能的影响, 电化学测试表明: 140 ℃处理6 min的碳粉为载体制备的催化剂对甲醇的电催化氧化活性最佳.     

Fabrication of nanocapsules with Au particles trapped inside carbon and silica nanoporous shells

Carbon capsules with hollow cores and mesoporous shells (HCMS) containing entrapped Au particles were prepared by template replication from solid core/mesoporous shell silica spheres with encapsulated Au particles. The resulting HCMS carbon capsules were then nanocast one step further to generate Au-trapping hollow core silica capsules with nanostructured shells.     

分级结构氮掺杂碳纳米笼担载的铂基高效甲醇氧化电催化剂

高性能低成本的担载型铂基催化剂是直接甲醇燃料电池(DMFC)实用化过程中的一大挑战.利用高比表面积、高稳定性、容易负载金属的载体实现 Pt颗粒的高度分散,既可提高催化剂的催化性能,又可提高 Pt的利用率以降低成本,是担载型 Pt基催化剂实用化的有效途径.碳材料是一种常用的催化剂载体,近年来我们课题组发展了一种高性能的碳纳米笼材料,并可通过异原子掺杂调变其表面性能,提高其活性和负载能力.我们采用原位氧化镁模板法制备氮掺杂碳纳米笼：以具有多级结构的碱式碳酸镁作为氧化镁模板的前体,吡啶为碳源和氮源,经高温热解沉积,在原位形成的氧化镁模板表面形成氮掺杂的石墨化碳纳米薄层;经稀盐酸浸泡并洗涤,获得高纯度的氮掺杂碳纳米笼.氮掺杂碳纳米笼具有分等级的微纳米结构、高导电性、高比表面积和可调变的孔结构,结合表面氮原子的锚钉作用,氮掺杂碳纳米笼有望成为电化学催化剂 Pt的优良载体.
　　在前期研究基础上,本文探索多级结构氮掺杂碳纳米笼(hNCNC)作为新型载体负载 Pt的能力,并评价所构建的负载型催化剂 Pt/hNCNC的电催化性能.通过简便的微波辅助多元醇还原法,将氯铂酸还原成 Pt纳米粒子负载于 hNCNC的表面.为了揭示氮掺杂的效应,我们对比研究了具有相似分级结构但无掺杂的碳纳米笼(hCNC)以及商业化活性炭(Val-can XC-72)作为载体的情况.经热重(TG)和 X射线光电子能谱(XPS)分析,三种催化剂 Pt/hNCNC、Pt/hCNC和 Pt/XC-72的负载量均接近理论负载量(23.1 wt%),都主要以金属态存在.然而,扫描电子显微镜(SEM)和透射电子显微镜(TEM)结果表明, Pt/hNCNC的 Pt分散状态优于 Pt/hCNC,更远优于 Pt/XC-72. Pt/hNCNC的平均 Pt粒径最小,仅约3.3 nm.这种良好的分散状态主要得益于氮原子掺杂,高负电性的氮原子改变了局域的表面极性,有利于 Pt颗粒的成核,也有利于固定 Pt颗粒.
　　由于 hNCNC对 Pt的优异分散能力, Pt/hNCNC表现出高的电化学活性面积.氢吸附和一氧化碳溶出伏安曲线表明, Pt/hNCNC的电化学活性面积高于 Pt/hCNC和 Pt/XC-72,这与显微观察和 X射线衍射(XRD)结果相吻合. Pt/hNCNC展现出优异的甲醇电催化氧化活性和高稳定性,其催化电流明显高于 Pt/hCNC和 Pt/XC-72,电流衰减亦慢于 Pt/hCNC和 Pt/XC-72. hNCNC的分级微纳米结构有利于孔内传质和电子输运,从而提高反应速度. hNCNC的氮掺杂有利于 Pt在载体表面的分散,增强了载体-金属相互作用,提高了电化学活性面积和催化活性.为了进一步考察 hNCNC对 Pt的负载能力,本文还考察了高负载量 Pt/hNCNC的性能.在负载量高达60 wt%时, Pt/hNCNC中的 Pt颗粒仍无明显聚集,其甲醇氧化电流增加了30%,可以有效提高 DMFC的输出电流密度.
　　综上可见, hNCNC可以有效分散并稳定 Pt颗粒,从而提高电化学活性面积和甲醇电催化氧化活性,优于未掺杂的碳纳米笼和传统碳材料,展示了 hNCNC高分散 Pt颗粒用作 DMFC的高效阳极催化剂的重要前景,也表明 hNCNC有望成为应用广泛的新型载体.     

A Novel Sul ded Mo/C Catalyst for Direct Vapor Phase Carbonylation of Methanol at Atmospheric Pressure

The direct carbonylation of methanol, without any halide in the feed as a promoter, is presented. A series of Mo catalysts supported on activated carbon, y-Al2O3 and SiO2 were prepared. The results show that the support greatly affects the Mo catalyst in the direct vapor-phase carbonylation of methanol, and activated carbon is the best supports of the investigated supports. In addition, the relationships between adsorptions of NH3 and CO and carbonylation of methanol were investigated. A novel sulfided Mo/C catalyst had high activity and selectivity for the vapor phase carbonylation of methanol to methyl acetate without the addition of a CH3I promoter to the feed. The reaction conditions were optimized at a reaction temperature of 573 K, a methanol concentration of 23 mol% and a carbon monoxide space velocity of 3,000 L/(kg-h). Under these optimal conditions a methanol conversion of 50%, carbonylation selectivity of 80 mol%, and space-time yield of 8.0 mol/(kg-h) were obtained. The active phase of this     

Methanol electrooxidation on a colloidal PtRu-alloy fuel-cell catalyst

The electrooxidation of methanol on a novel carbon supported PtRu electrocatalyst produced via colloidal PtRu precursors was investigated by thin-film-electrode (TFE) measurements and compared with commercially available Pt and PtRu catalysts. The PtRu-colloid-based catalyst shows similiar activity towards methanol oxidation as other conventional PtRu catalysts. A comparison with literature data from half-cell measurements at similiar mass-specific current densities clearly demonstrates the high potential of the colloid-based PtRu catalyst for fuel-cell applications.     

Remarkable support effect of SWNTs in Pt catalyst for methanol electrooxidation

Carbon nanotubes have been proposed as advanced metal catalyst support for electrocatalysis. In this work, different carbon support materials including single-walled carbon nanotubes (SWNTs), multi-walled carbon nanotubes (MWNTs) and XC-72 carbon black, were compared in terms of their electrochemical properties using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The SWNTs is found to exhibit the highest accessible surface area in electrochemical reactions and the lowest charge transfer resistance at the SWNTs/electrolytes. These carbon materials are then loaded with varying amount of Pt by the electrodeposition technique to prepare carbon supported Pt catalysts. Electrochemical measurements of methanol oxidation reveal that the SWNTs supported Pt catalyst exhibits the highest mass activity (mA/mg-Pt). In comparison with Pt-XC-72 and Pt-MWNTs, the remarkably enhanced electrocatalytic activity of the Pt-SWNTs maybe attributed to a higher dispersion and utilization of the Pt particles, which are directly related to the electrochemical characteristics of SWNTs. The high concentration of oxygen-containing functional groups, high accessible surface area, low charge transfer resistance at the carbon/electrolyte interfaces can be important for the Pt dispersing and strong metal-support interaction in the Pt-SWNTs catalyst.     

Efficient Nd Promoted Rh Catalysts for Vapor Phase Methanol Carbonylation

ANd promoted-Rh catalysts supported on polymer-derived carbon beads for vapor-phas emethanol carbonylation was developed. Rh-Nd bimetallic catalysts obviously have higher activity than that of supported Rh catalyst under similar reaction condition. The difference between the activity of above two catalyst systems is clearly caused by the intrinsic properties generated by the introduction of Nd.     

Highly graphitized carbon-wrapped PtFeCo alloy with enhanced durability and activity toward methanol electro-oxidation

Exploring efficient strategies to construct durable and active Pt-based electrocatalysts toward methanol oxidation reaction (MOR) remains great significance for the application of direct methanol fuel cells (DMFCs). Here, we report a facile pyrolysis procedure for fabricating carbon layer wrapped PtFeCo alloy nanoparticles supported on nitrogen-doped carbon nanotubes (NCNT). Physical characterizations demonstrate that the nitrogen-doped carbon support is highly graphitized and the PtFeCo particles are firmly wrapped by the graphitized carbon. Since the wrapping of highly graphitized carbon effectively prevents PtFeCo alloy from metal dissolution, the durability of the synthesized PtFeCo/Co–NCNT_a catalyst has been substantially improved, remaining about 76% of its initial mass activity after 1000 cycles of durability test in acid condition. In addition, due to the strain and ligand effects caused by alloying Pt with Fe and Co, the PtFeCo/Co–NCNT_a catalyst exhibits a greatly enhanced mass activity of 4.2-fold and a specific activity of 6.3-fold higher than those of commercial Pt/C-JM catalyst. Consequently, this work may provide an effective route for preparing durable and active Pt-based catalysts for methanol electro-oxidation.     

Electrocatalytic oxidation of methanol on Pt-Pd nanoparticles supported on honeycomb-like porous carbons in alkaline media

Honeycomb-like porous carbons (PCs) were synthesized using a facile self-assembly method with phenolic resin as the carbon source and tetraethyl orthosilicate (TEOS) as the silica source. The PCs were found to have a large BET surface area of 458 m² g^?1 and a partially graphitized structure. The obtained PCs were used as a support for various Pt-Pd bimetallic alloy catalysts employed for methanol oxidation in alkaline media. Compared with Pt supported on commercial Vulcan XC-72R carbon (Pt/C) and with the other Pt-Pd bimetallic alloy catalysts on PCs, Pt₃Pd₁ on PCs displayed the most negative onset potential for methanol oxidation and the highest steady-state current (2.04 mA cm^?2). This may be because the Pt₃Pd₁/PCs catalyst has the largest electrochemical active surface area (ESA), and because adding Pd to the catalyst improves the ability of the intermediate species to tolerate oxidation. The results show that the prepared Pt-Pd/PCs is a potential candidate for application as a catalyst in alkaline direct methanol fuel cells.     

载体对浸渍型Cu/Mn/Mg/K甲醇裂解催化剂的影响

载体对浸渍型Cu/Mn/Mg/K甲醇裂解催化剂的影响;     

氧化铝担载的贵金属铱基催化剂的制备及其对甲醇裂解反应的催化性能

 以ZrO2, La2O3或MgO为助剂制备了氧化铝担载型铱基催化剂,考察了其对甲醇裂解反应的催化性能,并用X射线光电子能谱、程序升温还原、 H2程序升温脱附和CO程序升温脱附等技术对催化剂进行了表征. 结果表明, ZrO2, La2O3和MgO助剂的引入均能提高主产物氢气和CO的选择性. ZrO2是甲醇裂解反应的优良助剂,可以显著提高甲醇的转化率和氢气的收率. 氧化铝担载型贵金属铱基催化剂上存在强的氢溢流现象,这使催化剂具有良好的反应性能,同时有利于产物的脱附,氧化物助剂的加入能够进一步促进氢的溢流.     

Hydrogenation of benzophenone by carbon-supported Pd catalysts

Catalytic activity of palladium catalysts with two different types of carbon support, Norit (an activated carbon), and bamboo-shaped carbon nanotubes (BCNT) have been tested for benzophenone hydrogenation. The selectivity toward the two possible reaction products (benzhydrol and diphenylmethane) can be directed by the catalyst support. It has been found that the Norit support preferred the over-hydrogenation of benzhydrol to diphenylmethane. The BCNT support proved to be much more selective and resulted as much as 99.3% benzhydrol selectivity at 96.3% benzophenone conversion. The high benzhydrol selectivity might be explained by the presence of covalently bonded nitrogen atoms in the catalyst (BCNT: 6.19 w/w%, Norit 0.54 w/w%) that can inhibit the over-hydrogenation process, thereby BCNTs are better catalyst supports for benzhydrol production than the commonly used activated carbon–supported catalysts.     

用于甲醇直接气相氧化羰基化的负载铜催化剂

 采用浸渍法制备了负载型铜基催化剂,并用其催化甲醇直接气相氧化羰基化合成碳酸二甲酯(DMC), 考察了浸渍溶剂、载体、助催化剂和铜含量的影响. 结果表明,以CuCl为活性组分原料、浓氨水为浸渍溶剂和活性炭为载体制得的负载铜催化剂显示出很高的催化活性,在特定的反应条件下,该催化剂上甲醇的转化率可达27.7%, DMC选择性可达95%. 分子筛负载的铜催化剂上甲醇的转化率低于1%, 但是生成DMC的选择性高达100%. 催化剂活性随着Cu负载量的增加而增大,但负载量过高可引起甲醇的过度氧化反应,导致DMC选择性下降. 催化剂中添加KOH或钯化合物,有利于提高以CuCl2为活性组分原料制得的铜催化剂的活性,但同时也促进了副反应的发生. 随着反应时间的延长,催化剂的活性组分流失,活性下降,但是生成DMC的选择性维持在95%左右.     

Physical and electrochemical characterizations of microwave-assisted polyol preparation of carbon-supported PtRu nanoparticles

PtRu nanoparticles supported on Vulcan XC-72 carbon and carbon nanotubes were prepared by a microwave-assisted polyol process. The catalysts were characterized by transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy (XPS). The PtRu nanoparticles, which were uniformly dispersed on carbon, were 2-6 nm in diameter. All PtRu/C catalysts prepared as such displayed the characteristic diffraction peaks of a Pt face-centered cubic structure, excepting that the 2theta values were shifted to slightly higher values. XPS analysis revealed that the catalysts contained mostly Pt(0) and Ru(0), with traces of Pt(II), Pt(IV), and Ru(IV). The electro-oxidation of methanol was studied by cyclic voltammetry, linear sweep voltammetry, and chronoamperometry. It was found that both PtRu/C catalysts had high and more durable electrocatalytic activities for methanol oxidation than a comparative Pt/C catalyst. Preliminary data from a direct methanol fuel cell single stack test cell using the Vulcan-carbon-supported PtRu alloy as the anode catalyst showed high power density.     

Anchoring metal nanoparticles on hydrofluoric acid treated multiwalled carbon nanotubes as stable electrocatalysts

We attempted the treatment of multiwalled carbon nanotubes (MWCNTs) in hydrofluoric acid (HF) aqueous solution for depositing Pt nanoparticles as catalysts for methanol oxidation for the first time. The preliminary results revealed that the Pt nanoparticles could be well dispersed on HF treated MWCNTs and gave enhanced activity and stability for methanol oxidation. As demonstrated in this study, the Pt supported on HF treated MWCNTs catalyst gave over doubled current density than that of Pt supported on as-received MWCNTs for methanol oxidation at the same Pt loadings. The enhancement in the stability of the Pt supported on HF treated MWCNTs catalyst for methanol oxidation is believed due to the stronger interaction between Pt nanoparticles and MWCNTs. This study opens promising possibilities for anchoring metal nanoparticles on the walls of the MWCNTs uniformly and stably.     

Molybdenum-doped titanium dioxide supported low-Pt electrocatalyst for highly efficient and stable hydrogen evolution reaction

The Platinum(Pt)-based catalysts exhibit excellent catalytic performance for the hydrogen evolution reaction(HER) while suffering from poor stability due to the weak interaction between the carbon support and Pt.Herein,a molybdenum-doped titanium dioxide(Ti_(0.9)Mo_(0.1)O_2) supported low-Pt electrocatalyst with stronger interaction between catalyst and support is applied to tune the electrocatalytic performance of Pt.The Ti_(0.9)Mo_(0.1)O_2 support can not only tolerate the corrosion environment in the catalytic system,but also generate strong metal-support inte raction(SMSI) between the oxide and catalyst.A facile solvothermal method is used to prepare Ti_(0.9)Mo_(0.1)O_2 as support to anchor Pt nanoparticles.The 5% Pt supported on Ti_(0.9)Mo_(0.1)O_2 catalyst exhibits 4.4-fold mass activity(MA) at an overpotential of 50 mV and higher stability than 20% Pt/C with only 1/4 Pt loading.The SMSI between the Ti_(0.9)Mo_(0.1)O_2 and Pt prevents the Pt aggregation to achieve excellent stability,and hydrogen spillover effect in the interface between Pt and support benefits the hydrogen production process.This work presents a novel sight for the fabrication and design of oxide supported catalysts in various catalytic system by reasonably employing support effect.     

Palladium catalysts supported on activated carbon with different textural and surface chemical properties

A commercial activated carbon was used as catalyst support in Pd/AC catalysts. The effects of the different surface oxygen groups and textural properties of the carbon supports on the metal dispersion of the supported catalysts were analyzed.