Blending of Natural Rubber/Recycled Ethylene-Propylene-diene Rubber: Promoting the Interfacial Adhesion Between Phases by Natural Rubber Latex

This article deals with blends based on natural rubber (NR) and recycled ethylene-propylene-diene rubber (R-EPDM). Natural rubber latex (NRL) was introduced into the blends to enhance interfacial adhesion between NR and R-EPDM. A new route of compounding was also suggested. The blends were prepared by mixing R-EPDM and other additives in NRL before blending with natural rubber on a two-roll mill. By applying this method, the homogeneity of the blends and cross-linking distribution are significantly improved. The blends exhibited superior state of cure, swelling resistance, mechanical properties and dynamic mechanical properties. The degree of entanglement between NR and R-EPDM also increased after NRL modification.     

Simultaneous Enhancement of Mechanical and Dynamic Mechanical Properties of Natural Rubber/Recycled Ethylene-Propylene-Diene Rubber Blends by Electron Beam Irradiation

Mechanical and dynamic mechanical properties of natural rubber/recycled ethylene-propylene-diene rubber (NR/R-EPDM) blends were simultanoeusly enhanced by electron beam (EB) irradiation. The cross-linking promoter, trimethylolpropane triacrylate (TMPTA), was also introduced into the blends to induce the cross-linking. By applying EB irradiation, the tensile modulus, hardness, swelling, cross-link density, and storage modulus increased with increase in the irradiation dose; an irradiation dose of 50 kGy was efficient to gain optimum tensile strength. The formation of irradiation-induced cross-links after EB irradiation is a major concern for the enhancement of mechanical, swelling resistance, and dynamic mechanical properties of the blends.     

Thermo-Mechanical Performance of Natural Rubber/Recycled Ethylene-Propylene-Diene Rubber Blends in the Presence of ZnO Nanoparticles

In the present study, recycled ethylene-propylene-diene rubber (R-EPDM) was used in an attempt to create a value-added natural rubber (NR) material based on NR/R-EPDM blends. ZnO nanoparticles were also incorporated in a way to replace the conventional ZnO together with special attention to improve the thermo-mechanical performance of the blends. Polyhedral and spherical shapes of ZnO nanoparticles were synthesized, and they were found to have no impurities, with a dimension ranging from 10 to 40 nm. ZnO nanoparticles not only act as a curing activator but also improve the thermal stability and dynamic mechanical properties of the blends.     

Compounding,mechanical and morphological properties of carbon-black-filled natural rubber/recycled ethylene-propylene-diene-monomer (NR/R-EPDM) blends

Blends of natural rubber/virgin ethylene-propylene-diene-monomer (NR/EPDM) and natural rubber/recycled ethylene-propylene-diene-monomer (NR/R-EPDM) were prepared. A fixed amount of carbon black (30 phr) was also incorporated. The effect of the blend ratio (90/10, 80/20, 70/30, 60/40 and 50/50 (phr/phr)) on the compounding, mechanical and morphological properties of carbon-black-filled NR/EPDM and NR/R-EPDM blends was studied. The results indicated that both the carbon-black-filled NR/EPDM and NR/R-EPDM blends exhibited a decrease in tensile strength and elongation at break for increasing weight ratio of EPDM or R-EPDM. The maximum torque (S′M_H), minimum torque (S′M_L), torque difference (S′M_H?M_L), scorch time (ts₂) and cure time (tc₉₀) of carbon-black-filled NR/EPDM or NR/R-EPDM blends increased with increasing weight ratio of virgin EPDM or R-EPDM in the blend. SEM micrographs proved that, for low weight ratios of virgin EPDM or R-EPDM, the blends exhibited high surface roughness and matrix tearing lines. The blends also showed a reduction in crack path with increasing virgin EPDM or R-EPDM content over 30 phr. This reduction in crack path could lead to less resistance to crack propagation and, therefore, low tensile strength.     

Morphology and mechanical and viscoelastic properties of natural rubber and styrene butadiene rubber latex blends

The morphology and mechanical and viscoelastic properties of a series of blends of natural rubber (NR) and styrene butadiene rubber (SBR) latex blends were studied in the uncrosslinked and crosslinked state. The morphology of the NR/SBR blends was analyzed using a scanning electron microscope. The morphology of the blends indicated a two phase structure in which SBR is dispersed as domains in the continuous NR matrix when its content is less than 50%. A cocontinuous morphology was obtained at a 50/50 NR/SBR ratio and phase inversion was seen beyond 50% SBR when NR formed the dispersed phase. The mechanical properties of the blends were studied with special reference to the effect of the blend ratio, surface active agents, vulcanizing system, and time for prevulcanization. As the NR content and time of prevulcanization increased, the mechanical properties such as the tensile strength, modulus, elongation at break, and hardness increased. This was due to the increased degree of crosslinking that leads to the strengthening of the 3‐dimensional network. In most cases the tear strength values increased as the prevulcanization time increased. The mechanical data were compared with theoretical predictions. The effects of the blend ratio and prevulcanization on the dynamic mechanical properties of the blends were investigated at different temperatures and frequencies. All the blends showed two distinct glass‐transition temperatures, indicating that the system is immiscible. It was also found that the glass‐transition temperatures of vulcanized blends are higher than those of unvulcanized blends. The time–temperature superposition and Cole–Cole analysis were made to understand the phase behavior of the blends. The tensile and tear fracture surfaces were examined by a scanning electron microscope to gain an insight into the failure mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2189–2211, 2000     

Impact modification of thermoplastics by methyl methacrylate and styrene-grafted natural rubber latexes

The preparation and characterization of polymer blends with structured natural rubber (NR)-based latex particles are presented. By a semicontinuous emulsion polymerization process, a natural rubber latex (prevulcanized or not) was coated with a shell of crosslinked polymethylmethacrylate (PMMA) or polystyrene (PS). Furthermore, core–shell latexes based on a natural rubber/crosslinked PS latex semi-interpenetrating network were synthesized in a batch process. These structured particles were incorporated as impact modifiers into a brittle polymer matrix using a Werner & Pfleiderer twin screw extruder. The mechanical properties of PS and PMMA blends with a series of the prepared latexes were investigated. In the case of PMMA blends, relatively simple core (NR)–shell (crosslinked PMMA) particles improved the mechanical properties of PMMA most effectively. An intermediate PS layer between the core and the shell or a natural rubber core with PS subinclusions allowed the E-modulus to be adjusted. The situation was different with the PS blends. Only core–shell particles based on NR-crosslinked PS latex semi-interpenetrating networks could effectively toughen PS. It appears that microdomains in the rubber phase allowed a modification of the crazing behavior. These inclusions were observed inside the NR particles by transmission electron microscopy. Transmission electron photomicrographs of PS and PMMA blends also revealed intact and well-dispersed particles. Scanning electron microscopy of fracture surfaces allowed us to distinguish PS blends reinforced with latex semi-interpenetrating network-based particles from blends with all other types of particles.     

A SAXS and swelling study of cured natural rubber/styrene–butadiene rubber blends

A small‐angle X‐ray scattering (SAXS) and swelling study of natural rubber and styrene–butadiene rubber blends (NR/SBR) is presented. To this aim, specimens of NR and SBR and blends with 75/25, 50/50, and 25/75 NR/SBR ratios (in phr) were prepared at a cure temperature of 433 K and the optimum cure time (t₁₀₀). This time was obtained from rheometer torque curves. The system of cure used in the samples was sulfur/n‐t‐butyl‐2‐benzothiazole sulfenamide. From swelling tests of the cured samples, information about the molecular weight of the network chain between chemical crosslinks was obtained. For all cured compounds, in the Lorentz plots built from SAXS scattering curves, a maximum of the scattering vector q around 0.14 Å^?1 was observed. However, the q position shows a linear‐like shift toward lower values when the SBR content in the SBR/NR blend increases. In pure NR or SBR the q values show a different tendency. The results obtained are discussed in terms of the existence of different levels of vulcanization for each single phase forming the blend and the existence of a third level of vulcanization located in the interfacial NR/SBR layer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2320–2327, 2009     

Improving properties of natural rubber/polyamide 12 blends through grafting of diacetone acrylamide functional group

The aim of the present study was to improve the compatibility in blends of natural rubber (NR) and polyamide 12 (PA12) by grafting NR with hydrophilic monomer, diacetone acrylamide (DAAM), via seeded emulsion polymerization. The increase in polarity of NR after grafting modification was confirmed by a considerable increase in the polar component of its surface energy. Blends of graft copolymers of NR and poly(diacetone acrylamide) prepared using 10 wt% of DAAM (NR‐g‐PDAAM10) and PA12 were prepared at a 60/40 blend ratio (wt%) using simple blend and dynamic vulcanization techniques. The mechanical and rheological properties of the resulting blends were subsequently investigated and compared with those of the corresponding blends based on unmodified NR. The results show that dynamic vulcanization led to a significant increase in both mechanical and rheological properties of the blends. It was also observed that the dynamically cured NR‐g‐PDAAM10/PA12 blend had smaller particle size of vulcanized rubber dispersed in the PA12 matrix than observed for the dynamically cured NR/PA12 blend. This is due to the compatibilizing effect of DAAM groups present in NR‐g‐PDAAM10 molecule, which decreases the interfacial tension between the two polymeric phases. Therefore, it can be stated that the interfacial adhesion between NR and PA12 was improved by the presence of DAAM groups in NR molecule. This was reflected in the higher tensile properties observed in the dynamically cured NR‐g‐PDAAM10/PA12 blend. Copyright © 2017 John Wiley & Sons, Ltd.     

Influence type of natural rubber on properties of green biodegradable thermoplastic natural rubber based on poly(butylene succinate)

Green biodegradable thermoplastic natural rubber (GB‐TPNR) based on simple blend of natural rubber (NR) and poly(butylene succinate) (PBS) was prepared using three NR alternatives: unmodified NR and epoxidized NR with 25‐ or 50‐mol% epoxide (ie, ENR‐25 or ENR‐50). It was found that ENR‐50/PBS blend showed the best compatibility, which resulted in superior mechanical and thermal properties with the highest crystallinity of the PBS phase, on comparing with the ENR‐25/PBS and NR/PBS blends. This might be attributed to stronger chemical interactions between the epoxide groups in ENR‐50 and the polar functional groups in PBS, which were confirmed by Fourier transform infrared (FTIR). Furthermore, scanning electron microscopy (SEM), atomic force microscopy (AFM), and polarizing optical microscopy (POM) micrographs of ENR‐50/PBS blend revealed phase separation with finer‐grained cocontinuous structure than in ENR‐25/PBS and NR/PBS simple blends. Furthermore, the chemical interactions in ENR‐50/PBS blend enhanced the resistance to accelerated weathering.     

Interrelationship between total volatile organic compounds emissions,structure and properties of natural rubber/polycaprolactone bio-blends cross-linked with peroxides

Natural rubber/polycaprolactone (NR/PCL) bio-based blends with different organic peroxides were prepared using an internal batch mixer and subsequently cross-linked at 170 °C. Two types of commonly used organic peroxides, dicumyl peroxide and di(tert-butylperoxyisopropyl)benzene peroxide, were applied as free-radical initiator. Cross-linking efficiency of NR/PCL blends were investigated using oscillating disc rheometer measurements, followed by infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis and tensile testing. Total volatile organic compounds (TVOCs) emissions were determined using headspace analysis integrated with gas chromatography with flame ionization detector. Determined TVOCs emissions varying in range 21.6–52.1 μg/g and generally value of this parameter decreased with increasing content of PCL phase in studied blends or with application of more efficient di(tert-butylperoxyisopropyl)benzene peroxide as cross-linking agent. It was found that increasing of TVOCs parameter indicated deterioration of mechanical properties of NR/PCL blends, which corresponded with the changes in chemical structure and thermal properties of cross-linked NR/PCL. This confirms that evaluation of TVOCs parameter is interesting alternative for “conventional methods” to characterization of the studied bio-based blends.     

线性低密度聚乙烯/橡胶共混体系的相容性研究

本文用FTIR-ATR方法考察了线性低密度聚乙烯与天然橡胶(NR)及丁苯橡胶(SBR)两个共混体系,发现NR的835cm~(-1)和SBR的964cm~(-1)两个吸收峰因与聚乙烯共混而增高变窄,说明聚乙烯的非晶链段和橡胶分子之间存在一定程度的相互作用。     

Dynamic mechanical and thermal properties of physically compatibilized natural rubber/poly(methyl methacrylate) blends by the addition of natural rubber‐graft‐ poly(methyl methacrylate)

The dynamic mechanical and thermal properties of natural rubber/poly (methyl methacrylate) blends (NR/PMMA) with and without the addition of graft copolymer (NR‐g‐PMMA) have been investigated. Dynamic mechanical spectroscopy is used to examine the effect of compatibilizer loading on storage modulus (E′), loss modulus (E″) and loss tangent (tan δ) at different temperatures and at different frequencies. The morphology of the blends indicates that the size of the dispersed phase decreased by the addition of a few percent of the graft copolymer followed by a leveling off at higher concentrations. This is an indication of interfacial saturation. Attempts have been made to correlate morphology with dynamic mechanical properties. Various models have been used to fit the experimental viscoelastic results. Differential scanning calorimetry has been used to analyze the glass‐transition temperatures of the blends. The thermal stability of the blends has been analyzed by thermogravimetry. Compatibilized blends are found to be more thermally stable than uncompatibilized blends. Finally the miscibility and mechanical properties of the blends annealed above T_g are evaluated. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 525–536, 2000     

Reinforcement of compatibilized NR/NBR blends by fly ash particles and precipitated silica

Effects of precipitated silica (PSi) and silica from fly ash (FA) particles (FASi) on the cure and mechanical properties before and after thermal and oil aging of natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) blends with and without chloroprene rubber (CR) or epoxidized NR (ENR) as a compatibilizer have been reported in this paper. The experimental results suggested that the scorch and cure times decreased with the addition of silica and the compound viscosity increased on increasing the silica content. The mechanical properties for PSi filled NR/NBR vulcanizates were greater than those for FASi filled NR/NBR vulcanizates in all cases. The PSi could be used for reinforcing the NR/NBR vulcanizates while the silica from FA was regarded as a semi‐reinforcing and/or extending filler. The incorporation of CR or ENR enhanced the mechanical properties of the NR/NBR vulcanizates, the ENR being more effective and compatible with the blend. The mechanical properties of the NR/NBR vulcanizates were improved by post‐curing effect from thermal aging but deteriorated by the oil aging. Copyright © 2008 John Wiley & Sons, Ltd.     

Dynamically cured natural rubber/EVA blends: influence of NR‐g‐poly(dimethyl (methacryloyloxymethyl)phosphonate) compatibilizer

Graft copolymer of natural rubber and poly(dimethyl(methacryloyloxymethyl)phosphonate) (NR‐g‐PDMMMP) was prepared in latex medium via photopolymerization. It was then used to promote the blend compatibility of dynamically cured 40/60 natural rubber (NR)/ethylene vinylacetate copolymer (EVA) blends using various loading levels at 1, 3, 5, 7, 9, 12, and 15 wt%. It was found that the increasing loading levels of NR‐g‐PDMMMP in the blends caused the increasing elastic modulus and complex viscosity until reaching the maximum values at a loading level of 9 wt%. The properties thereafter decreased with the increasing loading levels of NR‐g‐PDMMMP higher than 9 wt%. The smallest vulcanized rubber particles dispersed in the EVA matrix with the lowest tan δ value was also observed at a loading level of 9 wt%. Furthermore, the highest tensile strength and elongation at break (i.e., 17.06 MPa and 660%) as well as the lowest tension set value (i.e., 27%) were also observed in the blend using this loading level of the compatibilizer. Addition of NR‐g‐PDMMMP in the dynamically cured NR/EVA blends also improved the thermal stability of the blend. That is, the decomposition temperature increased with the addition of the graft copolymer. However, the addition of NR‐g‐PDMMMP in the blends caused the decreasing degree of crystallinity of the EVA phase in the blend. However, the strength properties of the blend are still high because of the compatibilizing effect. Copyright © 2009 John Wiley & Sons, Ltd.     

Styrene butadiene rubber/epoxidized natural rubber blends: dynamic properties, curing characteristics and swelling studies

The dynamic properties, curing characteristics and swelling behaviour of styrene butadiene rubber (SBR) and epoxidized natural rubber (ENR) blends were studied. The incorporation of ENR 50 in the blends improved processability, stiffness, resilience and reduced the damping property. In terms of curing characteristics, the scorch time, t₂ and curing time, t₉₀ of the SBR/ENR blends decrease with increasing ENR content. At room temperature (23°C) and at 100°C the swelling degree of the SBR/ENR blends decreases with increasing ENR content.     

Raman investigation of thermoplastic vulcanizates based on hydrogenated natural rubber/polypropylene blends

Raman spectroscopy including mapping technique appears as a powerful technique for the characterization of polymer blends like thermoplastic elastomers (TPEs) and thermoplastic vulcanizates (TPVs). The Raman spectra of polymers blends such as natural rubber/polypropylene (NR/PP) and 65% hydrogenated natural rubber/polypropylene (65%HNR/PP) were identified and the phase distribution was determined. The study was driven for the same type of blends in TPEs state and TPVs state obtained after to 2 different processes, either peroxide cure or sulfur cure. The morphology of TPEs and TPVs obtained by Raman spectroscopy were compared and confirmed using scanning electronic microscopy.Raman mapping shows that the phase morphology of NR/PP, 65%HNR/PP, were characterized as continuous rubber phase morphology of the thermoplastic elastomers (TPEs) and a fine dispersion of cross-linked rubber phase in a continuous matrix of the thermoplastic vulcanizates (TPVs). Raman spectroscopy is demonstrated to be a reference to determine the content ratio of each component in the TPVs. Moreover, Raman mapping could be used to calculate the phase size of cross-linked rubber phase dispersed in the thermoplastic vulcanizates (TPVs).     

Effect of maleic anhydride and liquid natural rubber as compatibilizers on the mechanical properties and impact resistance of the NR‐NBR blend

The degree of compatibilization between natural rubber (NR) and acrylonitrile‐butadiene rubber (NBR) was investigated by two different methods. NBR was chemically modified with maleic anhydride in a screw twin mixer with and without reaction initiator, benzoyl peroxide. Also, the effects of molecular weight of liquid natural rubber (LNR) as a compatibilizer were studied. The degree of compatibilization between NBR and NR is determined indirectly through measurements of mechanical properties and impact resistance. The maleic anhydride and benzoyl peroxide concentrations influence the mechanical properties and impact resistance of the blends. Also, the mechanical properties of the blends showed that the molecular weight of LNR played an important role in determing their performance. Copyright © 2004 John Wiley & Sons, Ltd.     

The influence of physical ageing on the electrical and swelling behaviour of ternary rubber vulcanizates

The effects of pre-annealing ageing time at 70 °C on the electrical properties and swelling behaviour in kerosene of a new tri-block rubber based on blends of natural rubber (NR) and different concentration ratios of both styrene-butadiene rubber (SBR) and butyl rubber (IIR), all incorporating 40 phr (parts per hundred parts of rubber by weight) of high abrasion furnace (HAF) carbon black, were investigated.

It was found that the interspacing distance, d, between carbon particles or aggregates is greatly affected by physical ageing and also by the rubber ratios in the test specimens.

Moreover, the degree of swelling, Q (%), in kerosene was found to decrease with both physical ageing and IIR content of the specimen.     

Effects of partial replacement of silicone rubber with flurorubber on properties of dynamically cured poly(vinylidene fluoride)/silicone rubber/flurorubber ternary blends

Blends of poly(vinylidene fluoride) (PVDF), silicone rubber (SR) and flurorubber (FKM) were prepared via peroxide dynamic vulcanization. The effect of FKM loading on the morphology, mechanical properties, crystallization behavior, rheology and dynamic mechanical properties of the PVDF/SR/FKM ternary blends was investigated. A “network” was observed in the PVDF/SR binary blends, which disappeared in the ternary blends, but a core-shell-like structure was formed. The mechanical properties were significantly improved. The Izod impact strength of PVDF/SR/FKM blend with 19 wt% FKM was 18.3 kJ/m², which was 3–4 times higher than the PVDF/SR binary blend. The complex viscosity and storage modulus of the PVDF/SR/FKM blends decreased with increasing FKM content, hence the processability was improved. The increase of FKM content seemed to show a favorable effect on the crystallization of the PVDF component. It promoted the nucleation process of PVDF, leading to increased polymer crystallization rate and higher crystallization temperature. The glass-rubber transition temperature of the PVDF phase moved to a lower temperature.     

POSS nanoparticles as a potential compatibilizer for natural rubber/butadiene rubber blends

In this study, it was aimed to investigate octavinyl‐polyhedral oligomeric silsesquioxane (OV‐POSS) incorporation into natural rubber (NR)/butadiene rubber (BR) elastomer blends as a potential compatibilizer. The effects of OV‐POSS loading levels on the thermal, mechanical, morphological, and dynamic‐mechanical properties of elastomer blends were explored. Fourier‐Transform Infrared Spectrometer (FTIR), Temperature Scanning Stress Relaxation (TSSR), and Differential Scanning Calorimetry (DSC) results revealed the conceivable effect of OV‐POSS nanoparticles in the vulcanization through reacting with sulfur and/or elastomers. Scanning Electron Microscope (SEM), X‐Ray Diffraction (XRD), and tensile test measurements supported the improvement of mechanical properties due to homogeneous dispersion at low loading levels. On the other hand, high amount of OV‐POSS incorporation (7 and 10 phr) resulted in a decrease in mechanical properties, owing to the agglomeration of nanoparticles. According to contact angle and Dynamic mechanical analysis (DMA) results, it could be concluded that OV‐POSS nanoparticles were localized at the interface of the elastomers and enabled the compatibilization of immiscible NR/BR blends.