Development and Validation of a Simple and Efficient Method for the Determination of Pendimethalin and Its Metabolite M455H001 in Soil by Liquid Chromatography–Tandem Mass Spectrometry (LC-MS/MS)

A new analytical method has been developed and described for the rapid determination of pendimethalin and its major metabolite M455H001 in soil by liquid chromatography coupled with ion-spray tandem mass spectrometry (LC-MS/MS) after a single acidic solvent extraction. The chromatographic separation of the analytes was achieved using a Zorbax C18 reversed phase column and water/0.1% formic acid and methanol as the mobile phase at a flow rate of 0.2?mL?min^?1. The recoveries of the method ranged from 78.8% to 119.8% for pendimethalin and from 73.7% to 108.8% for M455H001, and the relative standard deviation was lower than 16% for both analytes. The validated limit of quantification was 0.01?µg?g^?1 soil dry weight for both compounds. The matrix effects were evaluated and were less than 20% for both substances in the examined soil samples. It is concluded that the method is easy, with reasonable consumption of reagents, characterized by reliability and sensitivity, and therefore, it is suitable for monitoring the levels of pendimethalin and its major metabolite M455H001 in soils.     

Dissipation dynamics of fenoxaprop-p-ethyl and fenoxaprop acid under Indian rice field conditions

Dissipation dynamics of fenoxaprop-p-ethyl (FPPE) and fenoxaprop acid (FPA) (metabolite) in rice field conditions was investigated for two consecutive seasons. FPPE dissipated rapidly in soil with average half life of 1.42–2.19 days. Dissipation followed first-order kinetics. The method was validated in terms of accuracy, linearity, specificity and precision. Linearity was in the range of 0.005–5 µg mL^?1 with limit of detection as 0.002 and 0.001 µg mL^?1 for fenoxaprop-p-ethyl and fenoxaprop acid, respectively. Quantitation limit in soil, grain, straw and husk were 0.005, 0.008, 0.01 and 0.01 µg g^?1 for fenoxaprop-p-ethyl, and 0.005, 0.01, 0.01 and 0.01 µg g^?1 for fenoxaprop acid, respectively. Recovery in soil, rice grains, straw and husk ranged from 81.60–93.40, 77.85–87.00, 75.20–84.40 and 76.00–87.20% for FPPE and 82.50–88.20, 76.25–83.00, 74.80–83.60 and 75.00–85.40% for FPA, respectively. Below detectable limit of residues of FPPE and metabolite were observed in soil, rice grain, husk and straw samples at harvest. FPPE and FPA were of short persistence under field conditions and residues were below European Union-Maximum Residue Limits in all matrices that would cause adverse effect on environment and human/animal health.     

Trace determination of malachite green in water samples using dispersive liquid–liquid microextraction coupled with high-performance liquid chromatography-diode array detection

A simple and reliable method has been developed for the rapid analysis of trace levels of malachite green from water samples using dispersive liquid–liquid microextraction and high-performance liquid chromatography-diode array detection. Factors relevant to the microextraction efficiency, such as the type and volume of extraction solvent, nature and volume of the disperser solvent, the effect of salt, sample solution temperature and the extraction time were investigated and optimised. Under the optimal conditions the linear dynamic range of malachite green was from 0.2 to 100.0?µg?L^?1 with a correlation coefficient of 0.9962. The detection limit and limit of quantification were 0.1?µg?L^?1 and 0.3?µg?L^?1, respectively. The relative standard deviation (RSD) was less than 2.6% (n?=?5) and the recoveries of malachite green (5.0?µg?L^?1) from water samples were in the range of 99.2?±?1.7%. Finally the proposed method was successfully applied for the analysis of malachite green from fish farming water samples.     

Pendimethalin in surface waters of rivers in the proximity of irrigated paddy fields by solid phase microextraction and gas chromatography

The aim of this study was to develop an analytical methodology for the determination of the herbicide pendimethalin in river waters in the towns of Turvo and Meleiro in the southern region of Santa Catarina State, Brazil. The method, based on solid phase microextraction (SPME) followed by separation and detection by gas chromatography (GC) and electron capture detection (ECD), respectively, was optimised and validated. The limits of detection (LOD) and quantification (LOQ) of 0.02 and 0.06?µg?L^?1, respectively, and recovery values in the range of 86.2 (±11.5)% to 103.4 (±9.5)% were obtained. It was verified that 53 river water samples showed contamination by pendimethalin at levels that ranged from 0.06 to 0.38?µg?L^?1.     

129I levels in soils from Ukraine and Slovenia in the last decade

¹²⁹I is important as an environmental tracer of the biogeochemical cycling of iodine and of the dissemination of nuclear pollution, because anthropogenic ¹²⁹I has been released from only few point sources and with its short mixing time its distribution therefore reveals the movement of ¹²⁹I in the environment. A radiochemical neutron activation analysis method was developed to measure the concentration of ¹²⁹I in soil samples. A procedure to pre-concentrate iodine from up to 150?g of soil was developed and validated using IAEA standard reference material IAEA-375 (Chernobyl soil). The method was applied to determine ¹²⁹I/¹²⁷I isotopic ratios as well as ¹²⁹I and ¹²⁷I concentrations in soils from several locations in Ukraine collected in 2006, 1996, 1993 and 1989, and from Slovenia, collected at various places in 2009 and 2006. The ¹²⁷I concentrations in surface soils from Ukraine were in the range 2.3–23.1?µg?g^?1 and for ¹²⁹I (11.1–245.7)?·?10^?8?µg?g^?1 dry matter with the highest value of 1.47?·?10^?3?µg?g^?1 found in a soil sample collected in Yaniv, Ukraine in July 1993. In soil samples from Slovenia ¹²⁷I concentrations ranged 0.73–130?µg?g^?1 and ¹²⁹I (8.0–245.7)?·?10^?8?µg?g^?1. The ¹²⁹I/¹²⁷I isotopic ratios of surface soils from Ukraine were in the range of the order of 10^?9–10^?5 and of 10^?10–10^?8 for soils from Slovenia. The highest isotopic ratio 13.6?·?10^?5 was found in a soil sample collected in Yaniv, Ukraine in July 1993.     

Novel and Rapid Deep Eutectic Solvent (DES) Homogeneous Liquid–Liquid Microextraction (HLLME) with Flame Atomic Absorption Spectrometry (FAAS) Detection for the Determination of Copper in Vegetables

Novel and fast deep eutectic solvent (DES)-based homogeneous liquid–liquid microextraction (HLLME) was applied for the extraction of copper from vegetable samples followed by flame atomic absorption spectrometry (FAAS). 1,5-diphenyl carbazone (DPC) was used as the chelating agent, and a DES was used as the extraction media. The utilized DES was based on benzyl triphenyl phosphonium bromide and ethylene glycol in a 1:8?mole ratio. The phase separation phenomenon was occurred by changing of sample temperature. Several factors influencing the extraction efficiency were investigated and optimized. Under the optimized conditions, an enhancement factor of 64 was obtained. The limit of detection, based on three signal-to-noise ratio, and limit of quantification were found to be 0.13?µg L^?1 and 5.0?µg L^?1, respectively. The calibration curve was linear within the range of 5.0–250?µg L^?1 with r² > 0.9957. Intra- and inter-day relative standard deviations (%) of 2.1% and 2.6% were obtained at the concentration of 25?µg L^?1. The accuracy of the proposed method was evaluated by analyzing a tomato leaves certified reference material and the results were to be in agreement with the certified value. Finally, the feasibility of the method was successfully confirmed by determination of copper in spinach, lettuce, broccoli, potato, carrot and parsley samples.     

Determination of 26 polychlorinated biphenyls congeners in soil samples using microwave-assisted extraction with open vessel and gas chromatography

A procedure focused on microwave-assisted extraction in open vessel (MAE-OV) and gas chromatography with electron capture detection (GC-ECD) was used for the determination of 26 congeners of polychlorinated biphenyls (PCBs) in soil samples. The limit of detection (LOD) and limit of quantification (LOQ) were evaluated for commercial PCBs mixture Aroclor1260. LOD and LOQ were calculated for each PCB congener, in the ranges (0.03–0.27?ng?g^?1) and (0.11–0.70?ng?g^?1), respectively. After optimization, 26 PCBs congeners were successfully extracted from soil samples with recovery amounts ranging between 84.7% and 117.3% for all PCBs congeners. The evaluated method of MAE-OV showed good separation and extraction of all PCBs congeners from soil samples. Extraction parameters such as solvent choice, power and extraction time were investigated. This study indicated that MAE-OV could be an interesting alternative method to extract PCBs from soils, since it is economical, easy, fast and requires low amounts of solvents.     

Chemical modification of alumina surface by immobilization of 1-((5-nitrofuran-2-yl)methylene)thiosemicarbazide for extractive concentration of silver ions

A column, solid phase extraction (SPE), preconcentration method was developed for determination of silver by using alumina coated with 1-((5-nitrofuran-2-yl)methylene)thiosemicarbazide and determination by flame atomic absorption spectrometry. The separation/preconcentration conditions for the quantitative recovery were investigated. At pH 2, the maximum sorption capacity of Ag⁺ was 7.5?mg?g^?1. The linearity was maintained in the concentration range of 0.02–11.0?µg?mL^?1 in the final solution or 0.14–1.10?×?10^4?ng?mL^?1 in the original solution for silver. The preconcentration factor of 140 and relative standard deviation of ±1.4% was obtained, under optimum conditions. The limit of detection (LOD) was calculated as 0.112?ng?mL^?1, based on 3σ_bl/m (n?=?8) in the original solutions. The proposed method was successfully applied to the determination trace amounts of silver in the environmental samples such as tea, rice and wheat flour, mint, and real water samples.     

Development and validation of a SPE-GC-MS method for the determination of pesticides in surface water

A method for analysis of 20 commonly used pesticides in surface water based on solid-phase extraction and gas chromatography-mass spectrometry was proposed. During method development the key parameters that can affect SPE extraction and determination such as selection of efficient SPE sorbent, pH of water sample, type and volume of elution solvent, breakthrough volume and matrix effects were investigated. The method was validated using spring water spiked with appropriate concentration of pesticides. The obtained correlation coefficients were in range 0.9972–1.000, limits of detection (LOD) were 0.001–0.5?µg?L^?1 and the limits of quantification (LOQ) were 0.005–1?µg?L^?1 depending on a pesticide. Much higher LOD (20?µg?L^?1) and LOQ (50?µg?L^?1) values were obtained for bentazone. The influence of matrix was assessed using real water samples spiked with appropriate concentration of pesticide standards solution. Both signal enhancement and suppression were observed, depending on a pesticide, therefore standard addition method was used for pesticides determination. The developed method was applied on real water samples taken in close vicinity of agricultural fields. Many of the targeted pesticides were found in the samples and the results are presented in this article.     

Determination of traces of As,Cd, Cr,Hg, Mn,Ni, Sb,Se, Sn and Pb in human hair by triple quadrupole ICP-MS

With the wide range of metallic contaminants discharged in the environment, studying the human health requires a growing number of elements to be monitored in biological samples. Hair analysis has been suggested as a suitable tool for biomonitoring environmental and occupational exposure to toxic elements. This study describes a method for the determination of 10 trace elements in hair samples using ICP-QQQ-MS. Combining the power of the MS/MS high-energy Helium mode with the MS/MS O₂ mass-shift mode, the method offers great analytical performances with detection limits reaching 0.0014 µg g^?1 for As, 0.0016 µg g^?1 for Cd, 0.012 µg g^?1 for Cr, 0.0035 µg g^?1 for Hg, 0.0055 µg g^?1 for Mn, 0.10 µg g^?1 for Ni, 0.0012 µg g^?1 for Sb, 0.0083 µg g^?1 for Sn, 0.011 µg g^?1 for Se and Pb. The accuracy of the method was tested on a human hair ERM® certified reference material. Percent recoveries varied from 91.3% and 106.9% being always in the acceptance range of 90–110%. For all analysed elements, RSD% of repeatability ranged between 0.6% and 9.0% and those of intermediate precision did not exceed the limit of 20% being always lower than 10% (except for As). The proposed method was applied for the determination of trace elements in hair samples from 20 unexposed subjects. The geometric mean levels were as follows: Cr 0.28 µg g^?1, Mn 0.30 µg g^?1, Sn 1.04µg g^?1, Sb 0.07 µg g^?1, Hg 0.42 µg g^?1, As 0.02 µg g^?1, Cd 0.03 µg g^?1, Ni 0.51 µg g^?1, Se 0.45 µg g^?1 and Pb 1.83 µg g^?1. Element concentrations were in the same range with the reported data. The reported results may be useful for environmental exposure assessment or comparisons studies when establishing reference values of trace elements in exposed population.     

Liquid-phase microextraction and gas-chromatographic determination of selenium(IV) in aqueous samples

A liquid-phase microextraction (LPME) method was employed for preconcentration of selenium as piazselenol complex in aqueous samples. The samples reacted with o-phenylenediamine in 0.1?M HCl at 90°C for 15?min, and then LPME was performed. A microdrop of carbon tetrachloride was applied as the extracting solvent. After extraction, the microdrop was introduced directly into the injection port of gas chromatography for analysis. Several important extraction parameters such as the type of organic solvent, sample and organic drop volumes, salt concentration, stirring rate, and exposure time were controlled and optimized. In the proposed LPME, the extraction was achieved by suspending a 3?µL carbon tetrachloride drop from the tip of a microsyringe immersed in 12.5?mL of aqueous solution. Under optimized conditions, a dynamic linear range was obtained in the range of 20–1000?µg?L^?1. The preconcentration factor and the limit of detection of selenium in this method were 91 and 0.9?µg?L^?1, respectively. The optimized procedure was successfully applied to the extraction and determination of selenium in different types of real samples. The relative standard deviations for the spiking levels of 50–100?µg?L^?1 in the real samples were in the range of 3.2–6.1%, and the relative errors were located in the range of ?5.4 to 5%.     

Determination of DDT in Animal Fats After Matrix Solid-Phase Dispersion Extraction Using an Activated Carbon Filter

A novel method for determining pp’-DDT, op’-DDT, pp’-DDE, and pp’-DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic organic solvents for sample preparation, followed by HPLC, has been developed. The sample is prepared by matrix solid-phase dispersion (MSPD) extraction with Toyobo-KF^®, an activated carbon fiber, as a new MSPD sorbent. The average recoveries (spiking levels: 0.2, 0.5, and 1.0 µg g^?1) ranged from 58 to 93%, with relative standard deviations of < 7%. The limits of quantitation were 0.18 µg g^?1.     

Rapid and sensitive determination of biphenyl and biphenyl oxide in water samples using dispersive liquid–liquid microextraction followed by gas chromatography

A rapid and sensitive method has been developed for the determination of biphenyl and biphenyl oxide in water samples using dispersive liquid–liquid microextraction followed by gas chromatography. This method involves the use of an appropriate mixture of extraction solvent (8.0?µL tetrachloroethylene) and disperser solvent (1.0?mL acetonitrile) for the formation of cloudy solution in 5.0?mL aqueous sample containing biphenyl and biphenyl oxide. After extraction, phase separation was performed by centrifugation and biphenyl and biphenyl oxide in sedimented phase (5.0?±?0.3?µL) were determined by gas chromatography-flame ionisation (GC-FID) system. Type of extraction and disperser solvents and their volumes, salt effect on the extraction recovery of biphenyl and biphenyl oxide from aqueous solution have been investigated. Under the optimum conditions and without salt addition, the enrichment factors for biphenyl and biphenyl oxide were 819 and 785, while the extraction recovery were 81.9% and 78.5%, respectively. The linear range was (0.125–100?µg L^?1) and limit of detection was (0.015?µg?L^?1) for both analytes. The relative standard deviation (RSD, n?=?4) for 5.0?µg?L^?1 of analytes were 8.4% and 6.7% for biphenyl and biphenyl oxide, respectively. The relative recoveries of biphenyl and biphenyl oxide from sea, river water and refined water (Paksan company) samples at spiking level of 5.0?µg?L^?1 were between 85.0% and 100 %.     

Validation of QuEChERS-based UPLC-MS/MS method for determination of quinoid niclosamide (LDS) residue in water,soil and rice samples

A sensitive, rapid and easy analytical method was validated for the determination of quinoid niclosamide (LDS) molluscicide in water, rice and soil using a QuEChERS extraction procedure and ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) detection. The LDS was extracted by using acetonitrile and then cleaned up by using dispersive solid-phase extraction with florisil and C18 sorbents. The determination of the target compound was achieved in less than 3 min using an electrospray ionisation source in negative mode. The overall average recoveries for this method in water, rice and soil matrix at three fortified levels ranged from 82.54 to 99.9%, with relative standard deviations in the range of 1.51 to 4.86% (n = 5). The calculated limits of detection were lower than 0.1 µg kg^?1 and quantification was 5 µg kg^?1; these values were much lower than the maximum residue levels established by the Australian standard (0.01 mg kg^?1). The results of the method validation confirmed that this proposed method is convenient and reliable for the determination of LDS molluscicide in water, rice and soil samples.     

Response surface optimisation applied to a headspace-solid phase microextraction-gas chromatography-mass spectrometry method for the analysis of volatile organic compounds in water matrices

A new method for the simultaneous determination of 12 volatile organic compounds (trans-1,2-dichloroethene, 1,1,1-trichloroethane, benzene, 1,2-dichloroethane, trichloroethene, toluene, 1,1,2-trichloroethane, tetrachloroethene, ethylbenzene, m-, p-, o-xylene) in water samples by headspace solid phase microextraction (HS–SPME)–gas chromatography mass spectrometry (GC–MS) was described, using a 100?µm PDMS (polydimethylsiloxane) coated fibre. The response surface methodology was used to optimise the effect of the extraction time and temperature, as well as the influence of the salt addition in the extraction process. Optimal conditions were extraction time and temperature of 30?min and ?20°C, respectively, and NaCl concentration of 4?mol?L^?1. The detection limits were in the range of 1.1?×?10^?3–2.3?µg?L^?1 for the 12 volatile organic compounds (VOCs). Global uncertainties were in the range of 4–68%, when concentrations decrease from 250?µg?L^?1 down to the limits of quantification. The method proved adequate to detect VOCs in six river samples.     

Cadmium and Lead Distribution in Marine Soil Sediments,Terrestrial Soil,Terrestrial Rock,and Atmospheric Particulate Matter around Split,Croatia

The distributions of cadmium and lead in marine sediments, surrounding soil, stones, and atmospheric particulate matter were determined at different locations in Split, Croatia. The determination of cadmium and lead was performed by flame atomic absorption spectrometry whereas atmospheric particulate matter samples were analyzed by inductively coupled plasma–optical emission spectrometry. Cadmium concentrations in the stones and soil were between 0.2 to 0.6 µg g^?1 and 0.2 to 0.9 µg g^?1. The concentration in the atmospheric particulate matter were <0.2 µg m^?2 d^?1(detection limit) to 1.4 µg m^?2 d^?1. Lead concentrations in marine sediments, stones, soil, and atmospheric particulate matter ranged from 31.2 to 144.4 µg g^?1, 9.3 to 29.4 µg g^?1, 11.3 to 66.1 µg g^?1, and 0.5 to 241.4 µg m^?2 d^?1, respectively. The relationship between determined parameters was established using principal component analysis and the results are in agreement with the assumption that anthropogenic sources play important roles for lead and cadmium distribution.     

Application of liquid phase microextraction based on solidification of floating organic drop for the determination of triazine herbicides in soil samples by gas chromatography with flame photometric detection

A simple and efficient liquid phase microextraction based on solidification of floating organic drop coupled with gas chromatography–flame photometric detection was developed for the extraction and determination of some triazine herbicides (metribuzin, simetryn, ametryn and prometryn) in soil samples. The type and volume of the extraction solvent, sample solution temperature, salt addition, stirring rate, and the extraction time were optimized. Under the optimal conditions, the linear response was observed over the range of 10–2000?µg?kg^?1 for metribuzin and 2–500?µg?kg^?1 for simetryn, ametryn, and prometryn, respectively, with the correlation coefficients (r) varying from 0.9990 to 0.9992. The limits of detection were in the range between 0.2 and 1.0?µg?kg^?1 (S/N?=?3?:?1). The recoveries of the target analytes for the spiked soil samples ranged from 75.5% to 97.3%, with the relative standard deviation values less than 7.2% (n?=?5). The enrichment factors were achieved ranging from 122 to 336. The developed method was applied for the preconcentration and determination of triazine herbicides in real soil samples and a satisfactory result was obtained.     

Elemental Analysis of Phytotherapeutic Products by Inductively Coupled Plasma–Tandem Mass Spectrometry

A procedure for the determination of As, Cd, Cr, Ni, Pb, and V in phytotherapy medicines by inductively coupled plasma–tandem mass spectrometry is reported. The use of tandem mass spectrometry with oxygen into an octopole reaction system at various gas flow rates and the combination of on-mass and mass-shift modes was evaluated. Cadmium, Cr, Ni, and Pb were determined as free atomic ions while As and V were determined as the oxides AsO⁺ and VO⁺ in the same run. Samples were prepared by microwave-assisted digestion with dilute nitric acid and hydrogen peroxide. Two plant-certified reference materials (apple leaves and tomato leaves) were used to check the accuracy. For tandem mass spectrometry with 0.5?mL min^?1 O₂, recoveries in the 85–113% were typically obtained and no statistical differences were observed at the 95% confidence level (t-test) in comparison with the certified values. Using these conditions, the limits of detection for the method were 0.01, 0.0002, 0.008, 0.008, 0.003, and 0.002?µg g^?1 for As, Cd, Cr, Ni, Pb, and V, respectively. The procedure was used for the analysis of four phytotherapic drugs and the determined concentrations were up to 0.168?µg g^?1 As, 0.03?µg g^?1 Cd, 0.82?µg g^?1 Cr, 1.18?µg g^?1 Ni, 0.52?µg g^?1 Pb, and 2.4?µg g^?1 V with average precision values of 8% as the relative standard deviation. The found concentrations were compared with limits proposed in official guidelines and, in most cases, the values were below the maximum limits allowed.     

Differential pulse polarographic behaviour of thiazopyr herbicide and application to its determination in fruit juice and soil samples

A differential pulse polarographic method for the determination of the herbicide thiazopyr has been developed. The polarographic study of thiazopyr exhibited two well-defined cathodic peaks within the pH range of 1.0 to 8.0. The variation of pH and polarographic parameters indicated that the optimum conditions under which thiazopyr could be reduced were a pH 7.0 BR buffer solution, a reduction peak potential of ?1270 mV (vs. SCE), scan rate of 5 mV s^?1, pulse amplitude of 50 mV with pulse duration of 50 ms at an ambient temperature of 25 ± 3°C. The main reduction peak was characterised by cyclic voltammetry as being irreversible and diffusion-controlled. A linear relationship between the peak current and the concentration of thiazopyr was obtained in the range of 0.43–38.6 µg mL^?1, with a detection limit of 0.127 µg mL^?1. The proposed method was successfully applied to the determination of thiazopyr in spiked fruit juice and soil samples. The mean recoveries of the 19.8 µg g^?1 and 3.96 µg mL^?1 thiazopyr spiked to soil and orange juice were 20.2 ± 1.0 µg g^?1 and 3.84 ± 0.12 µg mL^?1, at 95% confidence level, respectively. The sufficiently good recoveries and low relative standard deviation (RSD) data confirm the high accuracy and precision of the proposed method. The interferences effects of several commonly used pesticides and inorganic species were also studied. Interfering effects were eliminated either by providing selectivity with pH, or using EDTA as complexing agent.     

Development of chromatographic methods by using direct-sampling procedure for the quantification of cyclic and linear volatile methylsiloxanes in biogas as perspective for application in online systems.

By empirically examining the persistent theme, we hope to produce a more complete understanding of methods for determination of volatile methylsiloxanes in biogas stream. Therefore, we made an attempt to investigate a rapid and sensitive method for simultaneous analysis of linear and cyclic volatile methylsiloxanes in sewage biogas in the context of the perspective for application in online systems. The gas chromatographic (GC) parameters were optimised, and sampling of volatile methylsiloxanes from biogas was performed using novel direct sampling procedure with applying of three kinds of liquid-media. Through application of well-established gas chromatography technique coupled with two types of detector – flamed ionisation detector and mass spectrometer detector – we developed the characterisation of the presented methods. Moreover, during the samples preparation the extraction procedure was consistently excluded, as well as the time of analysis was significantly reduced. The analyses were carried out by applying special constructed sampling train where the absorbed VMSs were trapped and analysed directly by GC technique, afterwards. The instrumental analytical protocol was found to yield a linear calibration in the range 0.1–55.13 (µg g^?1) with R² values 0.996 and in the range from 0.1 to 65.17 µg g^?1) with R² values > 0.99 for GC-FID and GC-MS method respectively. In all analysed samples linear and cyclic VMSs were found in sewage gas with quantities exceeding 4.6 mg Nm^?3 and 19.9 mg Nm^?3, respectively Furthermore, estimation of VMSs solvent absorption efficiency was tested and the highest absorption efficiency was obtained when acetone was used as a primary solvent. High range of linearity (0.1–65.17 µg/g), and low values of limit of detection (0.01 µg/g), limit of quantification (0.04 µg/g) clearly indicate that the analysis can be successfully repeated in other independent laboratory. The proposed method creates the real perspective for analyis of VMSs in on-line system.