Thermal properties of 4,4-oxydiphathalic anhydride chitosan filled chitosan bio-composites

The 4,4,-oxydiphthalic anhydride-chitosan (ODAC) filler at composition of 2–12 wt/v% was selected to reinforce the Cs matrix by solution casting method. The thermal properties of the bio-composites were then evaluated by thermogravimetry analysis, differential scanning calorimetry, and dynamic mechanical analysis. The addition of ODAC filler in Cs matrix up to 10 wt/v% had increased the thermal stability of the bio-composites by increasing the thermal degradation (T _d) and glass transition temperature (T _g) of the bio-composites. Good interfacial bonds of electrostatic interactions and inter-hydrogen bonds of the bio-composite components significantly influenced the thermal properties of the bio-composites.     

Polylactide compositions. II. Correlation between morphology and main properties of PLA/calcium sulfate composites

Starting from calcium sulfate (gypsum) as fermentation by‐product of lactic acid production process, high performance composites have been produced by melt‐blending polylactide (PLA, L/D isomer ratio of 96:4) and β‐anhydrite II (AII) filler, that is, calcium sulfate hemihydrate previously dehydrated at 500 °C. Characterized by attractive mechanical and thermal properties due to good filler dispersion throughout the polyester matrix, these composites are interesting for potential use as biodegradable rigid packaging. Physical characterization of selected composites filled with 20 and 40 wt % AII has been performed and compared to processed unfilled PLA with similar amorphous structure. State of dispersion of the filler particles and interphase characteristic features have been investigated using light microscopy (LM) and scanning electron microscopy (SEM). Addition of AII did not decrease PLA thermal stability as revealed by thermogravimetry analyses (TGA) and allowed reaching a slight increase of PLA crystallizability during melt crystallization and upon heating from the glassy, amorphous state (DSC). It was found by thermomechanical measurements (DMTA) that the AII filler increased pronouncedly storage modulus (E′) of the composites in comparison with PLA in a broad temperature range. The X‐ray investigations showed stable/unchanged crystallographic structure of AII during processing with molten PLA and in the composite system. The notable thermal and mechanical properties of PLA–AII composites are accounted for by the good filler dispersion throughout the polyester matrix confirmed by morphological studies, system stability, and favorable interactions between components. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2770–2780, 2007     

Fabrication and characterization of gamma-irradiated recycled (thermoplastic/elastomer) matrix filled with feldspar composites

A composite of waste polyethylene, recycled waste rubber powder and reactive compatibilizing agent maleic anhydride, 60/40/2 mass%, was loaded with increasing contents, up to 20 mass%, of the reinforcing filler, feldspar [K (Al SiO₃O₈)]. The composites were gamma-irradiated at various doses up to 150 kGy. Selected physical, mechanical, and thermal parameters were investigated as functions of radiation dose and filler content. Gamma irradiation led to a significant improvement in the properties for all composites irradiated with 150 kGy. Similarly, the increase in feldspar content provided substantial improvement in properties as a result of development in the interfacial adhesion between the filler particles and composite components. The results were confirmed by examining the fracture surfaces using scanning electron microscopic techniques.     

Mechanical and thermal properties of Acacia leucophloea fiber/epoxy composites: Influence of fiber loading and alkali treatment

In this work, the influence of fiber content and alkali treatment on the mechanical and thermal properties of Acacia leucophloea fiber-reinforced epoxy composites was studied. Ten composite samples were fabricated by varying fiber content (5, 10, 15, 20, and 25 wt%); both untreated and treated fiber were soaked in a 5% NaOH solution for 45 min by using hand-layup method. The composite reinforced with 20 wt% treated fiber content exhibited better mechanical properties and thermal properties. Fourier transform infrared analysis, morphological analysis by atomic force microscope, and scanning electron microscope of composites were also performed.     

Effect of nanosilica on thermal oxidative degradation of SBR

The effect of silica content on thermal oxidative stability of styrene–butadiene rubber (SBR)/silica composites has been studied. Morphologies of silica in SBR with different contents are investigated by scanning electron microscopy, which indicates that silica can well disperse in SBR matrix below the content of 40 %, otherwise aggregates or agglomerates will generate. Composites with around 40 % silica content show excellent mechanical properties and retention ratios after aging at 85 °C for 6 days. The values of activation energy (E _a) of pure SBR and its composites are calculated by Kissinger and Flynn–Wall–Ozawa methods based on thermogravimetric (TG) results, which suggests that composite with about 20 % silica has minimum E _a, and composite with 30–40 % silica has maximum E _a. According to TG curves, it is found that silica can suppress the formation of char leading to decline in stability to some extent. On the other side, silica also has positive effect on improving thermal stability of the matrix as filler. Thus, the SBR/silica composites with silica content of 30–40 % can possess both excellent resistance to thermal oxidative degradation and superior mechanical properties.     

Enhancement of thermal conductivity and tensile strength of liquid silicone rubber by three-dimensional alumina network

ABSTRACT

Rapidly increasing demands for higher integration density and stability of electronic devices embrace higher requirements for thermally conductive silicone rubber, which is promisingly used in ultra-thin components. In this work, alumina whiskers (AWs) and alumina flakes (AFs) are used to modify liquid silicone rubber (LSR) by fabricating binary (AFs/LSR) or ternary (AWs/AFs/LSR) composites. The thermal conductivity and mechanical strength of the binary and ternary composites were investigated. Thermal conductivity of the binary AFs/LSR composite (25AFs/LSR) was 0.1990 W m^?1 K^?1, while the thermal conductivity of the ternary AFs/AWs/LSR composite (20AFs/5AWs/LSR) was 0.2655 W m^?1 K^?1. Furthermore, the tensile strength of the ternary AWs/AFs/LSR composites increased by 180.9% as compared with the binary system, increased to 7.81 MPa from 2.78 MPa due to the introduction of 1 wt% AWs. As a reason, a significant synergistic effect of AWs and AFs in the enhancement of both thermal and mechanical properties of the LSR was proved. Furthermore, the dielectric property measurements demonstrated that the ternary composites exhibited a lower dielectric constant and dielectric loss, indicating that the AWs/AFs/LSR composites were qualified to be applied in the field of electronic devices.     

Impact of surface adaptation and Acacia nilotica biofiller on static and dynamic properties of sisal fiber composite

Nowadays, the awareness of the public along with strict legitimate forces over the use of polymers, the manufacturing and automotive industries started using the renewable materials. Since, natural fiber reinforced composites play vital role in developing lightweight structural materials, this study focuses on utilizing sisal fiber as reinforcement in polyester matrix along with natural filler. The influence of fiber length and fiber volume fraction on the mechanical properties of sisal fiber was studied initially. Test results revealed that the composite with 20?mm fiber length and 20-volume fraction composite has better mechanical properties. Furthermore, the effect of fiber surface modification has been analyzed using various chemical solutions such as NaOH, KMnO₄, stearic acid, and maleic acid. Of these, NaOH treatment enhances the mechanical properties of composite compared to all other cases. Finally, the influence of Acacia nilotica, a natural filler addition into the alkali-treated sisal fiber composite has been evaluated by mechanical and dynamic mechanical properties. It is found that the addition of natural filler and surface treatment has enhanced the properties of composites due to their synergetic effect. This effect improves the adhesion and uniform stress transfer among the reinforcements. The fiber surface morphology was evaluated using micrographs obtained from scanning electron microscope.     

Rheology of Aqueous Solutions Containing SLES,CAPB, and Microemulsion: Influence of Cosurfactant and Salt

Aqueous solutions containing sodium lauryl ether sulphate (SLES) and cocamidopropyl Betaine (CAPB) with a constant total surfactant concentration (10 wt%) but different volume mixing ratios were prepared. A remarkable increase in the solutions’ viscosity at a volume mixing ratio of 34 v/v% SLES to 66 v/v% CAPB was observed. By increasing the volume ratio of SLES (r-value) in the binary mixture, the viscosity of 10 wt% SLES, which is close to that of water, increases to a maximum, but then drops down drastically at high r values (>45 v/v%). The maximum viscosity (V_max) is 2.8 Pas, whereas the minimum is 2 mPas. The rheological behavior at V_max has the remarkable feature of a simple Maxwell fluid over a large frequency range with one relaxation time. By adding a microemulsion (Plantasil Micro), the value of V_max decreases extremely, whereas adding cosurfactants like isodecyltrietheleneoxide (IT₃) or salts, like calcium chloride, leads to a pronounced increase in the value of V_max. At 0.76 wt% CaCl₂, V_max is 140 Pas and 150 Pas in the presence of 1 wt% IT₃. By increasing the SLES volume mixing ratio in the solution the maximum viscosity is shifted to higher CaCl₂ amounts. The increasing viscosity can be explained by a transformation of the micelle shape from spherical to rod-like. Whereas adding cosurfactants or salts leads to an increased entanglement between the rod-like micelles. Consequently, higher microemulsion amounts can be added before reaching the minimum viscosity.     

Thermal resistance and mechanical stability of tungsten oxide filled polymer composite radiation shields

Abstract

The influence of tungsten oxide on thermal and mechanical properties of Isophthalic polyester was studied in detail. Ultrasonication technique was successful in dispersing WO₃ filler particles upto 40?wt% into the polymer matrix and was confirmed through the Scanning Electron Microscopy technique. The mechanical strength of the composites was found to increase with increase in the WO3 content and is acting as a reinforcer. About 77.4%, 65.4% and 7–8 times increase was observed in tensile, flexural and compressive strength respectively with respect to pristine. The thermogram of the composites reveal two stages of degradation. Maximum weight loss was observed in the first stage of degradation in almost all the composites. The initial degradation temperature of the composites range from 151?°C–226?°C. Activation energy was estimated using Horowitz–Metzger kinetic theory and was found to range from 25.31 to 78.58?kJ/Mol. The 50?wt% WO3 filled composite exhibits excellent thermal stability and mechanical strength. Thus, WO₃ filler particles were successful in enhancing the thermal and mechanical strength of Isophthalic polyester.     

Polydimethylsiloxane–cristobalite composite adhesive system for aerospace applications

The effect of phase‐pure cristobalite (a high temperature crystalline polymorph of silica) on the adhesive characteristics of hydroxyl terminated polydimethylsiloxane (PDMS) was studied. The potential advantages of PDMS/cristobalite composite system as an adhesive for aerospace applications are also discussed. A PDMS/cristobalite composite adhesive system containing different filler contents (0–46 volume percentage, vol%) was prepared. The filler material, phase‐pure cristobalite, was synthesized by the pyrolysis of fused silica at 1400°C. The mechanical, rheological, and thermal characteristics of the composites were studied. A high yield stress (0.151 Pa), shear‐thinning index (1.051), and fast recovery rate were observed for ～34 vol% cristobalite loading, which indicate that PDMS retains its excellent adhesive and flow characteristics even at high filler loading with enhanced mechanical characteristics. Thermal analysis shows the onset of degradation of PDMS shifts to higher temperatures, 372–438°C and 317–417°C in nitrogen and air atmosphere respectively, which shows excellent thermal stability. The residual component yields after thermal degradation of PDMS/cristobalite composite system in nitrogen and air atmosphere show different degradation mechanisms. Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of barium titanate nanofiller on PEO/PVdF-HFP blend-based polymer electrolyte membrane for Li-battery applications

Organic-inorganic hybrid membranes based on poly(ethylene oxide) (PEO) 6.25 wt%/poly(vinylidene fluoride hexa fluoro propylene) [P(VdF-HFP)] 18.75 wt% were prepared by using various concentration of nanosized barium titanate (BaTiO₃) filler. Structural characterizations were made by X-ray diffraction and Fourier transform infrared spectroscopy, which indicate the inclusion of BaTiO₃ in to the polymer matrix. Addition of filler creates an effective route of polymer-filler interface and promotes the ionic conductivity of the membranes. From the ionic conductivity results, 6 wt% of BaTiO₃-incorporated composite polymer electrolyte (CPE) showed the highest ionic conductivity (6 × 10^?3 Scm^?1 at room temperature). It is found that the filler content above 6 wt% rendered the membranes less conducting. Morphological images reveal that the ceramic filler was embedded over the membrane. Thermogravimetric and differential thermal analysis (TG-DTA) of the CPE sample with 6 wt% of the BaTiO₃ shows high thermal stability. Electrochemical performance of the composite polymer electrolyte was studied in LiFePO₄/CPE/Li coin cell. Charge-discharge cycle has been performed for the film exhibiting higher conductivity. These properties of the nanocomposite electrolyte are suitable for Li-batteries.     

Thermal and mechanical properties of irradiated poly(vinyl chloride)/calcium carbonate composite

A composite consisting of PVC and CaCO₃ particles was irradiated with different doses of Gamma rays or electron beam in order to compensate the tensile strength decreases by filler addition. The deployment of irradiation process on the composite improved significantly the tensile strength by about 10–20 % using E-beam and Gamma irradiation at a dose of 250 kGy, respectively. Moreover, the irradiated composite exhibited higher thermal stability. Two thermal dehydrochlorination processes after irradiation have been observed instead of three thermal process before. The calculation of the activation energy of each step showed that initiation step consumed about 60 % of the used energy.     

Investigation of Physico-Chemical Properties of Alkali-Treated Prosopis juliflora Fibers

There is ever-increasing interest in using natural fibers in polymer composite systems and textile industry. Prosopis juliflora fibers (PJFs) possess ideal characteristics that make them suitable for various applications. Alkali treatment of PJFs was primarily aimed to change their physico-chemical properties; 5% (w/v) NaOH concentration and 60 min of soaking time were found to be optimal. It is intriguing to note that optimally treated PJFs had higher cellulose (72.27 wt.%), lower hemicellulose (4.02 wt.%) and lignin (12.09 wt.%) contents, higher crystallinity index (73%), tensile strength, and thermal stability.     

Development and validation of a novel RP-HPLC method for stability-indicating assay of Abiraterone acetate

Abiraterone acetate is a prodrug of Abiraterone widely used for the treatment of metastatic castration resistant prostate cancer. In this study, a simple, sensitive, and rapid stability-indicating reverse phase HPLC method was developed and validated for the determination of Abiraterone acetate in bulk and its pharmaceutical formulation. The method was developed by HPLC using a Hypersil ODS C-18 (150 mm × 4.6 mm, 5 µm) column in a isocratic mode with mobile phase constituted by potassium phosphate buffer and acetonitrile (40:60, v/v%) flow rate was 1.0 mL min^?1, column temperature of 30°C, UV detection wavelength 235 nm, and injection volume of 20 µL. The validated parameters were in accordance with FDA and ICH specifications, assay exhibited a linear range of 25–250 µg mL^?1 with regression (r²) coefficient 0.9998. The limits of detection and quantification were 0.23 and 0.70 µg mL. Accuracy was between 99.34 and 100.07%. The drug was subjected to various stress conditions like acidic, base hydrolysis, oxidation, thermal, and photolytic degradation. Stress study Abiraterone acetate was found susceptible to degrade under hydrolytic (acid and base) conditions. The proposed method has stability indicating the resolution of the main peak from their degradation peaks. The validated method is suitable for quality control application and reduced analysis time.     

In situ Formation of Mildly Oxidized Graphene Oxide/Polydicyclopentadiene Composite and Reinforced Mechanical and Thermal Performances

A series of mildly oxidized graphene oxide (MOGO) reinforced polydicyclopentadiene composites (MOGO/polyDCPD) were prepared via the in situ polymerization of DCPD in the presence of MOGO using ring-opening metathesis polymerization (ROMP). The inter-crosslinking networks between MOGO and polyDCPD backbones formed the reinforced composite structures, examined qualitatively by swelling tests. Bending tests, DMA and TGA measurements were employed to study the optimal loading content of MOGO for achieving the best mechanical and thermal properties of MOGO/polyDCPD composites. The results showed that the maximum mechanical performance was achieved with 0.1 wt% of MOGO loading. Excess MOGO led to decreased mechanical properties due to the poor solubility and uneven distribution of MOGO in the polymer matrix, which was confirmed by SEM. Meanwhile, the thermal stability of MOGO/polyDCPD composites showed a similar trend. The decomposition temperature at 10 wt% weight loss was significantly increased compared with the unfilled polyDCPD, but decreased with composition of MOGO above 0.1 wt%. The addition of MOGO may not only inhibit the back-biting from the catalyst and the formation of low molecular weight oligomers in the polymer, but also covalently immobilize them on its flake.     

Mechanical,Thermal and Morphological Behaviors of Castor Oil Based PU/PS Interpenetrating Polymer Network-Metakaolin Composites

The meta kaolin (MK) clay particulate filler with different weight ratios viz., 0, 5, 10, 20 and 30 wt% were incorporated into castable polyurethane (PU)/polystyrene (PS) (90/10) interpenetrating polymer network (IPN). The effects of MK particulate filler loading on the mechanical and thermal properties of PU/PS (90/10) IPN composites have been studied. From the tensile behavior, it was noticed that a significant improvement in tensile strength and tensile modulus as an increase in MK filler content. Thermogravimetric analysis (TGA) data reveals the marginal improvement in thermal stability after incorporation of MK filler. TGA studies of the IPN composites have been performed in order to establish the thermal stability and their mode of thermal degradation. It was found that degradation of all composites takes place in two steps. Degradation kinetic parameters were obtained for the composites using three mathematical models. Tensile fractured composite specimens were used to analyze the morphology of the composites by scanning electron microscopic (SEM) technique.     

Bacterial cellulose/gelatin composites: in situ preparation and glutaraldehyde treatment

Bacterial cellulose (BC)/GEL composites were prepared in situ by adding gelatin into BC-producing culture medium. The addition of gelatin interfered with the formation of the BC pellicle structure and thus made the BC yield and growth rate quite different from that of pure BC. Scanning electron microscope images showed that the width of cellulose ribbons became narrower than that of pure BC and the gelatin filled in the pores of BC to form a dense structure. The addition level of gelatin significantly influences the yield of BC/GEL composites. An optimum value of 0.5 wt/v% gelatin was attained, with which the highest yield of 0.0541 g/100 mL was achieved. Under this condition, the weight percentage of gelatin in BC/GEL composite was 65 wt%. BC/GEL composites were treated with glutaraldehyde to crosslink BC fibrils and gelatin. The crosslinking degree, determined by the concentration of glutaraldehyde and crosslinking time, could affect the swelling behavior, thermal stability and mechanical properties of composites. With increasing of the crosslinking degree, the crystallinity index and swelling behavior of the composites decreased. The increase in the crosslinking degree also descreased the composite’s strain at break in elongation but increased the compressive and tensile strength. Covalent bonding between BC and gelatin provides good strength retention to the glutaraldehyde-treated composites with a high crosslinking degree. Considering the cytocompatibility and properties of composites, the most appropriate concentration of glutaraldehyde and crosslinking time were 1.0 wt/v% and 24 h, respectively.     

Fabrication and characterization of composites composed of a bioresorbable polyester matrix and surface modified calcium carbonate whisker for bone regeneration

This work aims to evaluate the potential of a bioresorbable composite as material for bone regeneration. Surface‐modified calcium carbonate whiskers (CCWs) were prepared by grafting of ethylene glycol (EG) using 1,6‐hexamethylene diisocyanate as coupling agent, followed by ring‐opening polymerization of l ‐lactide initiated by the hydroxyl group of EG. The resulting PLLA‐EG‐g‐CCW was used as filler to reinforce a bioresorbable terpolymer, poly(l ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG). The mechanical properties and thermal stability of the PLTG/PLLA‐EG‐g‐CCW composites were greatly improved. Compared with neat PLTG, a 39.3% increase in tensile strength and 26.7% increase in elongation at break were obtained for the composite with 2 wt% PLLA‐EG‐g‐CCW filler. This was assigned to the reinforcement effect of evenly dispersed PLLA‐EG‐g‐CCW in the polymeric matrix. In fact, entanglement of PLLA grafts at the surface of PLLA‐EG‐g‐CCW with PLTG chains results in a homogeneous distribution of the filler in the matrix. Thus, the composites are simultaneously strengthened and toughened. The cytocompatibility of the materials was evaluated from cell morphology and 3‐(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide assay using L929 mouse fibroblast cell line. The results indicate that the composite presents very low cytotoxicity. Copyright © 2017 John Wiley & Sons, Ltd.     

不同结构颗粒对PMMA基复合材料性能影响

采用原位本体聚合法制备PMMA/MCM-41(with template),PMMA/SBA-15(with template),PMMA/SiO2三种复合材料.研究了介孔分子筛MCM-41,SBA-15和SiO2对PMMA复合材料拉伸强度,冲击强度,热稳定性的影响.由于合成介孔分子筛MCM-41,SBA-15时所用的模板剂CTAB和P123分布于孔口处和颗粒表面上,分别与PMMA基体产生物理缠结作用,增加了两者的相容性;且P123(EO20PO70EO20)表面有较大的PO/EO比率,与小分子量的CTAB相比有较强的疏水性,使得PMMA/SBA-15(with template)复合材料的性能要优于PMMA/MCM-41(with template).     

Efficient extraction of proteins from recalcitrant plant tissue for subsequent analysis by two‐dimensional gel electrophoresis

Protein extraction for two‐dimensional electrophoresis from tissues of recalcitrant species is quite problematic and challenging due to the low protein content and high abundance of contaminants. Proteomics in Shorea robusta is scarcely conducted due to the lack of a suitable protein preparation procedure. To establish an effective protein extraction protocol suitable for two‐dimensional electrophoresis in Shorea robusta, four procedures (borate buffer/trichloroacetic acid extraction, organic solvent/trichloroacetic acid precipitation, sucrose/Tris/phenol, and organic solvent/phenol/sodium dodecyl sulfate) were evaluated. Following these, proteins were isolated from mature leaves and were analyzed for proteomics, and also for potential contaminants, widely reported to hinder proteomics. The borate buffer/trichloroacetic acid extraction had the lowest protein yield and did not result in any banding even in one‐dimensional electrophoresis. In contrast, organic solvent/phenol/sodium dodecyl sulfate extraction allowed the highest protein yield. Moreover, during proteomics, organic solvent/phenol/sodium dodecyl sulfate extracted protein resolved the maximum number (144) of spots. Further, when proteins were evaluated for contaminants, significant (77–95%) reductions in the nucleic acids, phenol, and sugars were discernible with refinement in extraction procedure. Accumulated data suggested that the organic solvent/phenol/sodium dodecyl sulfate extraction was the most effective protocol for protein isolation for proteomics of Shorea robusta and can be used for plants that have a similar set of contaminants.