Temperature-controlled enhancement of oxygen uptake from water using oxygen carrier solution

Development of an artificial gill, for the uptake of oxygen from water to air, requires an increase in oxygen transfer rate. In the present study, oxygen transfer rate was enhanced using a washed red blood cell suspension as a thermo-responsive oxygen carrier solution, which changes oxygen affinity with temperature. Oxygen dissolved in water first combined with the oxygen carrier solution at a low temperature using a membrane module. The oxygen carrier solution was then heated to release oxygen into the air using a second membrane module. The water flow rate required to sustain a human being at rest was greatly reduced by heating the oxygen carrier solution due to increase in the limit of the oxygen partial pressure of water of which can be transferred, compared with when oxygen was transferred directly from water. The required membrane surface area is 225 m², sufficient for the development of a compact artificial gill.     

Influence of Pretreatment on the Interaction of Oxygen with Silver and the Catalytic Activity of Ag／SiO2 Catalysts for CO Selective Oxidation in H2

The interactions of oxygen with pre~reduced silver catalysts as well as their catalytic propertiesfor CO selective oxidation in H2 after oxygen pre-treatment are studied in this paper. It is found that the pretreatment exerts a strong influence on the activity and selectivity of the silver catalyst. A drop in activity and selectivity is observed after treating a pre-reduced catalyst with oxygen at low temperatures,whereas a converse result is obtained after an oxidizing treatment at high temperatures (T≥350℃). O2-TPD results show that surface oxygen species adsorbs on silver surface after the oxygen treatment at low temperatures. However, penetration of oxygen into the silver is enhanced by a high temperature treatment, meanwhile the surface oxygen species disappear. No other silver species except metallic silver are observed on all the catalysts by XRD, and the size of silver particle is not changed after the treatment with oxygen at low temperatures. The surface oxygen species formed by oxygen treatment can also be removed by hydrogen reduction. The strongly-adsorbed surface oxygen species prohibit the adsorption and diffusion of oxygen species in reaction gas on the surface of silver catalyst, causing the decrease in CO oxidation activity, in other words, it is important to obtain a clean silver surface for increasing the catalyst activity in CO removal from H2-rich feed gas. The differences in activity and selectivity due to the oxygen pretreatment at different temperatures axe discussed in terms of the changes in the surface/subsurface oxygen species of the silver particles.     

Concentration determination of oxygen nanobubbles in electrolyzed water

Water electrolysis is well known to produce solutions supersaturated with oxygen. The oxygen in electrolyzed solutions was analyzed with a dissolved oxygen meter and the Winkler method of chemical analysis. The concentration of oxygen measured with the dissolved oxygen meter agreed with that obtained using the Winkler method. However, measurements using a 10-fold dilution method showed a larger concentration of dissolved oxygen compared to the above methods. We developed a modified Winkler method to measure total oxygen concentration more accurately, which agreed with the results obtained from the 10-fold dilution experiment. The difference in measurements is due to the existence of oxygen nanobubbles, as confirmed by the observation of dynamic light scattering using a laser. Further analysis of the oxygen nanobubbles demonstrated that the stability of the nanobubbles was sufficient for chemical reaction and solvation to bulk solution.     

Ce-Fe-Zr-O/MgO整体型氧载体用于化学链部分氧化甲烷制合成气

以MgO为载体,采用球磨法制备了Ce-Fe-Zr-O/MgO粉末状氧载体,进而采用挤压成型法制备了整体型氧载体。研究了两种氧载体化学链部分氧化甲烷制合成气的性能,并通过XRD、H₂-TPR对氧载体进行表征。结果表明,粉末状氧载体中的储氧组分以Ce-Fe-Zr-O固溶体形式存在,而整体型氧载体的制备过程会导致Zr、Fe游离氧化物的形成。粉末状氧载体和整体型氧载体上均存在表面晶格氧和体相晶格氧,其中,体相晶格氧具有高选择性氧化甲烷的性能,可以将甲烷转化成CO和H₂。粉末状氧载体与甲烷反应活性较高,但其存在高含量的表面氧,易导致甲烷的完全氧化。整体型氧载体上体相晶格氧占据优势,可将甲烷选择性氧化为CO和H₂。氧化还原循环实验表明,粉末状氧载体在还原反应发生短时间内容易引起甲烷裂解导致产物气中的H₂/CO物质的量比显著大于2.0,同时产生大量积炭,制约了其循环性能。而整体型氧载体经10次循环实验后,全程反应过程中合成气H₂/CO物质的量比一直维持在2.0附近,显示了较高的循环稳定性能。     

Detection of uncombined oxygen in zirconium metal

This study was undertaken to develop a means of determining oxygen in zirconium which is present in a form other than that of zirconium Oxide.The method described determines oxygen which is evolved as molecular oxygen when solid zirconium metal is dissolved in hydrofluoric acid solution. Ihe oxygen evolved is caught in a separate flask and ultimately determined colorimetrically as iodine. In this procedure, the oxygen held as ZrO₂ is not evolved and is not determined.The range of oxygen determined by this method was between 50 to 170μ which is equivalent to 0. 06 to 0.22% oxygen. The deviation was ±0.01% oxygen.     

碘量法测定氧载体中的活性氧

氧载体中活性氧气的含量是衡量氧载体实用性的一项重要指标。自行设计了一种改进的碘量法测定混合气体中氧气的装置,完成了混合气体中微量氧气的测定,将该方法用于固相合成氧合氧载体中活性氧的测定,取得很好的结果,为混合气体中氧气的测定提供了新思路。     

New concept on air separation

A new process which combines oxygen permeable membrane with oxygen absorbent was proposed to simultaneously produce pure oxygen and nitrogen from air. In the process, air is fed in the oxygen permeable membrane, and a large part of oxygen permeates through the membrane. Then, the oxygen-depleted air (∼7% O₂) passes through an oxygen absorption bed to make the residual oxygen absorbed; simultaneously, pure nitrogen is produced at the exit of the absorption bed. After the absorption bed reaches its saturated capacity, the oxygen-depleted air pass through another absorption bed switched by an automatic 3-way valve; at the same time the saturated absorption bed is under a desorption process by vacuum to renew the absorption capacity. The pumped out oxygen has a high-purity due to the oxygen absorbent is 100% selectivity to oxygen. As a result, nearly 100% recoveries of oxygen and nitrogen, and >99.4% oxygen purity and >99.0% nitrogen purity was achieved simultaneously.     

Coverage dependence of oxygen decomposition and surface diffusion on rhodium 111: a DFT study

A systematic study of oxygen adsorption, decomposition and diffusion on Rh111 and its dependence on coadsorbed oxygen molecules has been performed using density functional theory calculations. First, the bonding strength between metal surface and adsorbed oxygen molecules has been studied as a function of initial oxygen coverage. The bonding strength decreases with increasing oxygen coverage, which points towards a self-inhibition of the adsorption process. The potential energy hypersurface (PES) for the dissociation of oxygen molecules adsorbed on a threefold fcc position perpendicular to the surface was calculated using a combined linear/quadratic synchronous transit method with conjugate gradient refinements. The results indicate that a minor amount of oxygen on the surface enhances the decomposition of further oxygen molecules, while this process is inhibited at higher coverage. Moreover, PES calculations of a single site jump of atomic oxygen on rhodium 111 indicate that the activation energy increases as well with increasing oxygen coverage. All results are discussed with respect to a rhodium based catalytic NOx reduction/decomposition system proposed by Nakatsuji, which decomposes nitrogen oxides in oxygen excess.     

Photogenerated singlet oxygen over zeolite-confined carbon dots for shape selective catalysis

Singlet oxygen as an activated oxygen species played an important role in organic synthesis. Suitable catalyst for converting ubiquitous oxygen molecule to singlet oxygen under mild conditions has attracted a wide range of attention. Herein, carbon dots have been confined into mesopores of silicalite-1 nanocrystals framework and acted as active sites for generation of singlet oxygen. The high oxygen-adsorption capacity of zeolite nanocrystals facilitated the photocatalytic generation rate of singlet oxygen, outpacing the free-standing carbon dots for 14-fold. The integrated carbon dot-zeolite nanocrystal hybrid also exhibited a special size-dependent selectivity for organic synthesis by using the in situ formed and confined singlet oxygen as active oxygen species.     

Underwater life support based on immobilized oxygen carriers

One of the primary problems that hinders humans in their efforts to explore and develop the ocean realms is the lack of a ready supply of oxygen. Practical methods have not yet been devised for using the vast amount of oxygen dissolved in ocean waters for human life support in an undersea environment. Fish and other water-breathing animals have solved this problem by utilizing hemoglobin as a molecular oxygen pump. To achieve a similar oxygen extraction capability, we have explored various methods of oxygen extraction that are based on immobilized forms of hemoglobin. Improved methods for immobilizing hemoglobin or other oxygen carrying molecules and a method for extracting the available dissolved oxygen from natural waters and other fluids are described. The techniques that have been developed allow for immobilization of oxygen carriers at high concentration in a state where they are capable of reversible oxygen binding, and also allow for regeneration of the carrier in the event of oxidation of the oxygen-binding site.     

Chain structures of surface hydroxyl groups formed via line oxygen vacancies on TiO2(110) surfaces studied using noncontact atomic force microscopy

Structures of surface hydroxyl groups arranged on a reduced TiO2(110) surface that had line oxygen vacancies were studied using noncontact atomic force microscopy (NC-AFM). NC-AFM results revealed that by increasing the density of oxygen vacancies on the TiO2(110) surface, line oxygen vacancies were formed by removal of oxygen atoms in a bridge oxygen row on the TiO2(110) surface. After the TiO2(110) surface with the line oxygen vacancies was exposed to water, the surface showed hydroxyl chain structures that were composed of hydroxyl groups linearly arranged in a form of two rows on the line oxygen vacancies and on a neighboring bridge oxygen row. In-situ NC-AFM measurements of these surfaces exposed to water at room temperature revealed that hydroxyl chain structures were formed at the line oxygen vacancy. Annealing above 500 K was sufficient to remove the hydroxyl chain structures on the TiO2(110) surface and allowed line oxygen vacancies to reappear on the surface. The line oxygen vacancies are active sites for water dissociation. In conclusion, the formation of the hydroxyl chain structure suggests that the surface hydroxyl groups on a TiO2(110) surface can be controlled by preparing oxygen vacancy structures on the surface.     

Hydrogen production from a combination of the water-gas shift and redox cycle process of methane partial oxidation via lattice oxygen over LaFeO3 perovskite catalyst

A redox cycle process, in which CH4 and air are periodically brought into contact with a solid oxide packed in a fixed-bed reactor, combined with the water-gas shift (WGS) reaction, is proposed for hydrogen production. The sole oxidant for partial oxidation of methane (POM) is found to be lattice oxygen instead of gaseous oxygen. A perovskite-type LaFeO3 oxide was prepared by a sol-gel method and employed as an oxygen storage material in this process. The results indicate that, under appropriate reaction conditions, methane can be oxidized to CO and H2 by the lattice oxygen of LaFeO3 perovskite oxide with a selectivity higher than 95% and the consumed lattice oxygen can be replenished in a reoxidation procedure by a redox operation. It is suggested that the POM to H2/CO by using the lattice oxygen of the oxygen storage materials instead of gaseous oxygen should be possibly applicable. The LaFeO3 perovskite oxide maintained relatively high catalytic activity and structural stability, while the carbonaceous deposits, which come from the dissociation of CH4 in the pulse reaction, occurred due to the low migration rate of lattice oxygen from the bulk toward the surface. A new dissociation-oxidation mechanism for this POM without gaseous oxygen is proposed based on the transient responses of the products checked at different surface states via both pulse reaction and switch reaction over the LaFeO3 catalyst. In the absence of gaseous-phase oxygen, the rate-determining step of methane conversion is the migration rate of lattice oxygen, but the process can be carried out in optimized cycles. The product distribution for POM over LaFeO3 catalyst in the absence of gaseous oxygen was determined by the concentration of surface oxygen, which is relevant with the migration rate of lattice oxygen from the bulk toward the surface. This process of hydrogen production via selective oxidation of methane by lattice oxygen is better in avoiding the deep oxidation (to CO2) and enhancing the selectivity. Therefore, this new route is superior to general POM in stability (resistance to carbonaceous deposition), safety (effectively avoiding accidental explosion), ease of operation and optimization, and low cost (making use of air not oxygen).     

The adaptability of Cu/Zr oxides as oxygen carrier used for chemical looping air separation (CLAS)

Chemical looping air separation (CLAS), based on the chemical looping principle, is a novel and energy-efficient method to separate oxygen from air. The oxygen carriers used capture oxygen from air in an oxidation reactor and release oxygen in a reduction reactor. In this work, the adaptability of Cu/Zr oxygen carrier used for CLAS was investigated through thermodynamic analysis and experimental methods. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to measure the phases and surface morphology of oxygen carriers before and after experiments. The results show that CuO has the capability of releasing oxygen when the temperature is higher than 725 °C in the nitrogen atmosphere, and the minimum oxygen reduction temperatures increase with the increasing of oxygen concentrations. The Cu/Zr oxygen carrier has high oxygen reduction and oxidation rates when temperature is higher than a certain values. For reduction, the value is about 860 °C. For oxidation, the value is about 500 °C. The reactivity of oxygen carrier increases significantly with the temperature increasing. On overall, reactivity of oxygen carrier has little difference under different particle sizes. The oxygen carrier exhibits a stable oxygen reduction and oxidation behavior during reduction–oxidation cycles. XRD patterns show that the main phases in reduced samples are Cu₂O and ZrO₂. The main phases in fresh and oxidized samples are CuO and ZrO₂. SEM images show that the fresh and reacted oxygen carriers are porous. The surface of reacted samples is smoother than fresh samples and no agglomeration has been found.     

Measurement of the dissolved oxygen concentration in acrylate monomers with a novel photochemical method

Because of the well‐known radical‐scavenging behavior, molecular oxygen is capable of inhibiting free‐radical chain polymerizations of unsaturated monomers. The deleterious effects of diffused oxygen in a polymerization system result in both a reduced polymerization rate and the loss of surface properties of a polymer film or coating. However, reliable data for oxygen concentration in organic monomers are relatively scarce because of the experimental and instrumental limitations of the commercially available techniques. In this study, a photochemical method was developed and was used to obtain the dissolved oxygen concentration in seven acrylate monomers. The principle of the method was to convert ground‐state molecular oxygen dissolved in monomer to the excited, singlet‐state oxygen and then react the singlet oxygen with a third compound (singlet oxygen trapper). By monitoring the concentration of this singlet oxygen trapper spectrophotometrically, the concentration of dissolved oxygen can be obtained with the established stoichiometry for the reaction between singlet oxygen and trapper. The singlet oxygen concentrations in the acrylate monomers varied from 0.59 to 2.07 × 10^?3 mol/L, depending on the monomer structure. The strategies and considerations for generalizing the method to other systems, including highly oxygenated organics, are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1285–1292, 2004     

Oxygen sensor via the quenching of room-temperature phosphorescence of perdeuterated phenanthrene adsorbed on Whatman 1PS filter paper

Perdeuterated phenanthrene (d-phen) exhibits strong room-temperature phosphorescence (RTP) when adsorbed on Whatman 1PS filter paper. An oxygen sensor was developed that depends on oxygen quenching of RTP intensity of adsorbed d-phen. The system designed employed a continuous flow of nitrogen or nitrogen-air onto the adsorbed phosphor. The sensor is simple to prepare and needs no elaborate fabrication procedure, but did show a somewhat drifting baseline for successive determinations of oxygen. Nevertheless, very good reproducibility was achieved with the RTP quenching data by measuring the RTP intensities just before and at the end of each oxygen determination. The calibration plots gave a nonlinear relationship over the entire range of oxygen (0-21%). However, a linear range was obtained up to 1.10% oxygen. A detection limit of 0.09% oxygen in dry nitrogen was acquired. Also, carbon dioxide was found to have a minimal effect on the RTP quenching. Thus, oxygen could be measured accurately in relatively large amounts of carbon dioxide. The performance of the oxygen sensor was evaluated by comparing data obtained with a commercial electrochemical trace oxygen analyzer. Also, additional information on the quenching phenomena for this system was obtained from the RTP lifetime data acquired at various oxygen contents.     

Spatial and temporal electrochemical control of singlet oxygen production and decay in photosensitized experiments

Active spatial and temporal modulation of domains of singlet oxygen activity is demonstrated using electrochemical tools. Using singlet oxygen microscopy in photosensitized experiments, it is shown that singlet oxygen concentrations around an ultramicroelectrode can be controlled by applying a bias voltage to the electrode. Two phenomena that can be exploited separately or collectively are examined: (1) the singlet oxygen concentration can be altered by local oxidation or reduction of the photosensitizer, which is the precursor to singlet oxygen, and (2) the reduction of oxygen to produce the superoxide anion which, among other things, is an effective singlet oxygen quencher, results in a local decrease in the concentration of singlet oxygen around the electrode. Both of these phenomena depend significantly on the diffusion of molecules along concentration gradients established by the biased electrode. The results reported herein demonstrate that one can indeed exert local electrochemical control and readily manipulate the population of singlet oxygen produced in a photosensitized process.     

甲基丙烯酸八氟戊酯乙烯基咪唑共聚物的合成及与钴卟啉复合物的氧结合性能

研究了甲基丙烯酸八氟戊酯单体及其与乙烯基咪唑共聚物的合成与表征 ,以及该共聚物与氧载体钴卟啉配位复合物的氧结合性能 .共聚物分子量和乙烯基咪唑含量分别由GPC和元素分析方法测定 ,结果为5 0× 10 4 和 2 5mol % .共聚物中的咪唑基与钴卟啉在溶液中配位 ,复合物具有快速、可逆的氧结合特性 .溶剂对复合物的氧结合性能影响较大 ,复合物在四氢呋喃中的氧结合亲合力大于在N ,N 二甲基甲酰胺中的亲合力     

Phosphorescent Ruthenium Complexes with a Nitroimidazole Unit that Image Oxygen Fluctuation in Tumor Tissue

Understanding oxygen fluctuation in a cancerous tumor is important for effective treatment, especially during radiotherapy. In this paper, ruthenium complexes bearing a nitroimidazole group are shown to report the oxygen status in tumor tissue directly. The nitroimidazole group was known to be accumulated in hypoxic tumor tissues. On the other hand, the ruthenium complex showed strong phosphorescence around 600 nm. The emission of ruthenium is quenched instantaneously by molecular oxygen due to energy transfer between triplet states of oxygen and ruthenium complex, but the emission is then recovered by the removal of oxygen. Thus, we could observe oxygen fluctuation in tumor tissue in a real‐time manner by monitoring the phosphorescence of the ruthenium complex. The versatility of the probe is demonstrated by monitoring oxygen fluctuation in living cells and tumor tissue planted in mice. The ruthenium complex promptly penetrated plasma membrane and accumulated in cells to emit its oxygen‐dependent phosphorescence. In vivo experiments revealed that the oxygen level in tumor tissue seems to fluctuate at the sub‐minute timescale.     

Electrochemical High Concentration Oxygen Sensing Using a Phosphonium Cation Based Room Temperature Ionic Liquid: Analytical Studies

Detecting oxygen at the high concentration limit needs innovation. Room temperature ionic liquid trihexyl(tetradecyl)phosphonium trifluorotris(pentafluoroethyl)phosphate [P_6,6,6,14][FAP] was tested as a solvent for oxygen detection through the electrochemical reduction of oxygen. Cyclic voltammetry of oxygen in nitrogen or carbon dioxide mixtures at different partial pressures was studied. The steady state current was shown to be linearly dependent on the oxygen partial pressure in high oxygen content (>77 %) systems. Simultaneous detecting of oxygen and carbon dioxide is also realised in an oxygen/carbon dioxide mixture, providing proof‐of‐concept of high concentration oxygen and carbon dioxide dual sensing.     

Osmotic phenomena in application for hyperbaric oxygen treatment

Hyperbaric oxygen (HBO) treatment defines the medical procedure when the patient inhales pure oxygen at elevated pressure conditions. Many diseases and all injuries are associated with a lack of oxygen in tissues, known as hypoxia. HBO provides an effective method for fast oxygen delivery in medical practice. The exact mechanism of the oxygen transport under HBO conditions is not fully identified. The objective of this article is to extend the colloid and surface science basis for the oxygen transport in HBO conditions beyond the molecular diffusion transport mechanism. At a pressure in the hyperbaric chamber of two atmospheres, the partial pressure of oxygen in the blood plasma increases 10 times. The sharp increase of oxygen concentration in the blood plasma creates a considerable concentration gradient between the oxygen dissolved in the plasma and in the tissue. The concentration gradient of oxygen as a non-electrolyte solute causes an osmotic flow of blood plasma with dissolved oxygen. In other words, the molecular diffusion transport of oxygen is supplemented by the convective diffusion raised due to the osmotic flow, accelerating the oxygen delivery from blood to tissue. A non steady state equation for non-electrolyte osmosis is solved asymptotically. The solution clearly demonstrates two modes of osmotic flow: normal osmosis, directed from lower to higher solute concentrations, and anomalous osmosis, directed from higher to lower solute concentrations. The fast delivery of oxygen from blood to tissue is explained on the basis of the strong molecular interaction between the oxygen and the tissue, causing an influx of oxygen into the tissue by convective diffusion in the anomalous osmosis process. The transport of the second gas, nitrogen, dissolved in the blood plasma, is also taken into the consideration. As the patient does not inhale nitrogen during HBO treatment, but exhales it along with oxygen and carbon dioxide, the concentration of nitrogen in blood plasma drops and the nitrogen concentration gradient becomes directed from blood to tissue. On the assumption of weak interaction between the inert nitrogen and the human tissue, normal osmosis for the nitrogen transport takes place. Thus, the directions of anomalous osmotic flow caused by the oxygen concentration gradient coincide with the directions of normal osmotic flow, caused by the nitrogen concentration gradient. This leads to the conclusion that the presence of nitrogen in the human body promotes the oxygen delivery under HBO conditions, rendering the overall success of the hyperbaric oxygen treatment procedure.