Measurement of the dissolved oxygen concentration in acrylate monomers with a novel photochemical method

Because of the well‐known radical‐scavenging behavior, molecular oxygen is capable of inhibiting free‐radical chain polymerizations of unsaturated monomers. The deleterious effects of diffused oxygen in a polymerization system result in both a reduced polymerization rate and the loss of surface properties of a polymer film or coating. However, reliable data for oxygen concentration in organic monomers are relatively scarce because of the experimental and instrumental limitations of the commercially available techniques. In this study, a photochemical method was developed and was used to obtain the dissolved oxygen concentration in seven acrylate monomers. The principle of the method was to convert ground‐state molecular oxygen dissolved in monomer to the excited, singlet‐state oxygen and then react the singlet oxygen with a third compound (singlet oxygen trapper). By monitoring the concentration of this singlet oxygen trapper spectrophotometrically, the concentration of dissolved oxygen can be obtained with the established stoichiometry for the reaction between singlet oxygen and trapper. The singlet oxygen concentrations in the acrylate monomers varied from 0.59 to 2.07 × 10^?3 mol/L, depending on the monomer structure. The strategies and considerations for generalizing the method to other systems, including highly oxygenated organics, are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1285–1292, 2004     

Cationic photopolymerization of liquid fullerene derivative under visible light

We describe the synthesis and cationic photopolymerization of a C₆₀ derivative bearing a 2,4,6‐tris(epoxynonyloxy)phenyl moiety (FB9ox). Rheological analysis of monomer indicates that temperature of 130 °C yields sufficiently low viscosity for polymerization. A thin film of the liquid monomer has been cationically photopolymerized with a photoinitiator system of curcumin and p‐(octyloxyphenyl)phenyliodonium hexafluoroantimonate, which harvests 424 nm light instead of commonly used ultraviolet light. The degree of polymerization was determined with ATR‐IR. The reaction is the first recorded photopolymerization of a fullerene derivative thin film. The polymer exhibits good mechanical and chemical stabilities. The polymerization can also be achieved by annealing at 150 °C without illumination, but with a smaller degree of polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5194–5201, 2008     

Surface engineering of styrene/PEGylated‐fluoroalkyl styrene block copolymer thin films

A series of diblock copolymers prepared from styrenic monomers was synthesized using atom transfer radical polymerization. One block was derived from styrene, whereas the second block was prepared from a styrene modified with an amphiphilic PEGylated‐fluoroalkyl side chain. The surface properties of the resulting polymer films were carefully characterized using dynamic contact angle, XPS, and NEXAFS measurements. The polymer morphology was investigated using atomic force microscope and GISAXS studies. The block copolymers possess surfaces dominated by the fluorinated unit in the dry state and a distinct phase separated microstructure in the thin film. The microstructure of these polymers is strongly influenced by the thin film structure in which it is investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 267–284, 2009     

Behavior and surface energies of polybenzoxazines formed by polymerization with argon,oxygen, and hydrogen plasmas

Polybenzoxazine (PBZZ) thin films can be fabricated by the plasma‐polymerization technique with, as the energy source, plasmas of argon, oxygen, or hydrogen atoms and ions. When benzoxazine (BZZ) films are polymerized through the use of high‐energy argon atoms, electronegative oxygen atoms, or excited hydrogen atoms, the PBZZ films that form possess different properties and morphologies in their surfaces. High‐energy argon atoms provide a thermodynamic factor to initiate the ring‐opening polymerization of BZZ and result in the polymer surface having a grid‐like structure. The ring‐opening polymerization of the BZZ film that is initiated by cationic species such as oxygen atoms in plasma, is propagated around nodule structures to form the PBZZ. The excited hydrogen atom plasma initiates both polymerization and decomposition reactions simultaneously in the BZZ film and results in the formation of a porous structure on the PBZZ surface. We evaluated the surface energies of the PBZZ films polymerized by the action of these three plasmas by measuring the contact angles of diiodomethane and water droplets. The surface roughness of the films range from 0.5 to 26 nm, depending on the type of carrier gas and the plasma‐polymerization time. By estimating changes in thickness, we found that the PBZZ film synthesized by the oxygen plasma‐polymerization process undergoes the slowest rate of etching in CF₄ plasma. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4063–4074, 2004     

Novel molecularly hybridized polyethylene/silica composite materials: Polymerization of ethylene with supported titanocenes by mesoporous silicates

A novel molecularly hybridized polyethylene/silica composite thin film was obtained by the gas‐phase polymerization of ethylene with a titanocene‐mounted mesoporous silica layer on a mica plate with mesoscopic pores arranged on the film surface. However, the use of titanocene‐mounted hexagonal domains of mesoporous silica on a glass plate for the gas‐phase polymerization of ethylene resulted in the formation of an islanded polyethylene/silica hybridized material. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4821–4825, 2000     

Synthesis and characterization of all‐conjugated copolymers of 3‐hexyl‐thiophene and EDOT by grignard metathesis polymerization

Random regioregular copolymers of 3‐hexylthiophene and 3,4‐ethylenedioxythiophene were synthesized by grignard metathesis polymerization. Soluble copolymers were obtained with a high degree of regioregularity and with a monomer ratio close to the feed ratio. A comparison between the optical properties and the thin film morphologies of these copolymers and poly(3‐hexylthiophene) is also presented. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

In‐line monitoring of UV photopolymerization with a quartz crystal resonator

An in‐line monitoring device using a quartz crystal resonator for thin film polymerization was proposed, and its performance has been evaluated by implementing in the UV polymerization of 2‐hydroxyethyl methacrylate with a photoinitiator of 1‐chloroanthraquinone. Because the variation of resonant resistance of the resonator is proportional to the square root of viscosity change that is closely related to the polymerization degree, the resistance can be used as a measure of the polymerization degree. The resistance measurements were compared with the outcome of instrumental analyses of polymerization degree using an FTIR spectrometer and a gel permeation chromatograph. The experimental results showed that the resistance measurements were consistent with the experimental outcome of the instrumental analyses, and this indicates the effectiveness of the proposed device. Owing to the simplicity and availability of the resonator system, its wide utilization in the monitoring of a variety of film polymerization processes, including photoresistor application, is expected. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2428–2439, 2006     

Ring‐opening polymerization of 1,4‐dioxan‐2‐one initiated by lanthanum isopropoxide in bulk

Lanthanum isopropoxide (La(OiPr)₃) has been synthesized and employed for ring‐opening polymerization of 1,4‐dioxan‐2‐one in bulk as a single‐component initiator. The influences of reaction conditions such as initiator concentration, reaction time, and reaction temperature on the polymerization were investigated. The kinetics indicated that the polymerization is first‐order with respect to the monomer concentration. The Mechanistic investigations according to ¹H NMR spectrum analysis demonstrated that the polymerization of PDO proceeded through a coordination‐insertion mechanism with a rupture of the acyl‐oxygen bond of the monomer rather than the alkyl‐oxygen bond cleavage. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5214–5222, 2008     

Synthesis and photopolymerization of novel multifunctional vinyl esters

Novel mono‐ and multifunctional vinyl ester monomers containing thioether groups were synthesized via an amine‐catalyzed Michael addition reaction between vinyl acrylate and multifunctional thiols. Using photo‐differential scanning calorimetry and real‐time Fourier transform infrared (RTIR) spectroscopy, the polymerization kinetics and oxygen inhibition of the homopolymerizations of the vinyl ester monomers were investigated. The effect of the vinyl ester and thioether group on acrylate/vinyl ester and thiol/vinyl ester copolymerizations was determined using real‐time IR spectroscopy to monitor polymerization rates of acrylate, vinyl, and thiol groups simultaneously. Polymerization of the vinyl esters used was found to be relatively insensitive to oxygen inhibition. We propose that the thioether group is responsible for reducing oxygen inhibition by a series of chain transfer/oxygen‐scavenging reactions. In polymerization of a acrylate/vinyl ester mixture both in nitrogen and in air, the vinyl ester monomer significantly enhances the polymerization rates and the conversion of the acrylate double bonds via plasticization of the crosslinked matrix and reduction of inhibition by oxygen. Ultimately, the vinyl ester monomer is incorporated into the polymer network. Thiol/vinyl ester free‐radical copolymerization is much faster than either thiol/allylether copolymerization or vinyl ester homopolymerization. The electron‐rich vinyl ester double bonds ensure rapid copolymerization with thiol. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4424–4436, 2004     

Effects of directed architecture in epoxy functionalized prepolymers for photocurable thin films

Cationic photopolymerization has become increasingly important in thin‐film applications for advantages including no oxygen inhibition and rapid polymerization rates. Photocurable cationic thin film properties are often modulated by incorporation of oligomeric and prepolymer materials, but little work has directly examined the effect of prepolymer structure and reactive group placement on the thermomechanical properties of the final material. To explore the role of molecular architecture, epoxy functionalized butyl acrylate gradient copolymers were synthesized with reactive groups in end segments or randomly distributed along the prepolymer chain. Polymerized end functionalized formulations exhibit moduli almost double that of random functionalized oligomer formulations. In addition, inclusion of end functionalized prepolymers decreases creep of resulting thin films by a factor of 10. Furthermore, decreasing the concentration of the cross‐linking diluent in end functionalized prepolymer systems results in amorphous networks with significantly lower mechanical strength. Increasing reactive groups at the ends of prepolymers produces stronger materials without affecting tensile elongation at break. These properties indicate that the structured oligomers facilitate the formation of continuous hard domains with high cross‐link density with inclusions of soft, flexible domains of low cross‐link density. This study demonstrates that the prepolymer architecture governs network formation and ultimate properties. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 144–154     

Monitoring ultrathin film photopolymerization of tetra‐alkylepoxyporphyrin by UV‐Vis spectroscopy

Cationic photopolymerization is a convenient in situ polymerization method for organic thin film preparation. In this work, the polymerization mechanisms is applied for highly viscous cross‐linking monomers, using tetra‐alkylepoxyporphyrin (TAEP) as a case study. By comparing the UV‐Vis spectra of the polymerized sample before and after the unreacted monomers have been dissolved, it is possible to estimate the polymerization yield. An IR spectrum of a reference thick film confirms full polymerization. Scanning fluorescence lifetime microscopy and AFM show the uniformity of the polymer. It was shown that photopolymerization is highly dependent on the substrate nature and requires at best case a 10 min illumination at 90 °C. Thermal polymerization of the same sample requires 10 min heating at 150 °C in dark. It was also shown that TAEP works as a self‐sensitizer for cationic photopolymerization. The proposed method is a mild and versatile technique for in situ preparation of thin polymeric films directly from chromophore monomers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6095–6103, 2009     

Free‐radical‐promoted cationic photopolymerization under visible light in aerated media: New and highly efficient silane‐containing initiating systems

New systems for the visible‐light‐induced polymerization of cationic resins working through a free‐radical‐promoted process are presented. They are based on a photoinitiator (camphorquinone, isopropylthioxanthone, Eosin), a silane, and a diphenyl iodonium salt, the new compound being the silane. The overall efficiency is strongly affected by the silane structure. The rates of polymerization and final percent conversion are noticeably higher than those obtained in the presence of already studied reference systems. Moreover, contrary to previously investigated free‐radical‐promoted cationic polymerizations, oxygen does not inhibit the process and an unusual enhancement of the polymerization kinetics is found in aerated conditions: such an observation seems to have never been reported so far. The excited state processes and the role of oxygen as revealed by laser flash photolysis are discussed. The particular behavior of the silyl radicals is outlined. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2008–2014, 2008     

Photo-hydroperoxidation and grafting of polyoctenamer. Access to new polymeric-hindered amine stabilizers

Polyoctenamer reacts with singlet oxygen to produce polymeric pendant hydroperoxide groups. Anthracene was used as a sensitizer for production of singlet oxygen under 365 nm irradiation. Remarkable differences were observed when the reaction was performed in the solid state or in the solution. Hydroperoxidation in the solution was much slower than in the film, and only pendant hydroperoxides were produced. Conversely, two processes take place in the film. One is the “ene” reaction of singlet oxygen with double bonds producing hydroperoxides as in the solution; the second one is a radical process producing both carbonyl products and additional hydroperoxides. This process went on after anthracene was completly consumed. Irradiation (λ > 300 nm) of hydroperoxidized polyoctenamer solution in the presence of monomers (2,2,6,6-tetramethyl or 1,2,2,6,6-pentamethyl-4-piperidyl acrylate) or stable nitroxyl radicals (stearoyloxy-2,2,6,6-tetramethyl-4-piperidyl-N-oxyl or TEMPO) grafted these monomers or stable radicals onto the polyoctenamer. Light stabilizing efficiency of grafted and low molecular additives was tested in polyoctenamer. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2599–2605, 1997     

Carboxylic acid‐containing benzoxazines as efficient catalysts in the thermal polymerization of benzoxazines

The autocatalytic thermal polymerization behavior of three benzoxazine monomers containing carboxylic acid functionalities is reported. Several mixtures of these carboxylic monomers and 3‐phenyl‐3,4‐dihydro‐2H‐1,3‐benzoxazine were prepared and their thermal polymerization behavior was analyzed by differential scanning calorimetry. The acid character of these reactive monomers increases the concentration of oxonium species, thus catalyzing the benzoxazine ring opening reaction. In this way the polymerization temperature decreased by as much as 100 °C in some cases. The existence of decarboxylation processes at high temperatures has been established by FTIR‐ATR and related to the increase in thermal stability observed by TGA in some cases. A relationship between the presence of carboxylic groups in the resulting materials and their flame retardancy behavior has also been established. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6091–6101, 2008     

Photopolymerization with microscale resolution: Influence of the physico‐chemical and photonic parameters

This article is aimed at demonstrating that physicochemical parameters can be used to control the spatial extent (length, width, and shape) of polymer objects in view of micro‐ and nano‐fabrication applications. In particular, we showed that oxygen quenching and internal filter effects could be turned to advantage to modulate the response of the material by controlling the threshold energy of polymerization and/or the shape of the light into the photopolymerizable medium. The experimental configuration used in this study is based on light‐induced polymerization at the extremity of an optical fiber that produces polymer micro‐objects after development. Spectroscopic approaches and polymerization threshold measurements were performed to quantitatively evaluate the influence of the physicochemical parameters on the micropatterning of photopolymerizable material. Interestingly, fluorescence that is usually regarded as a process competing with photopolymerization reaction, was used for controlling the fabrication process. By this means, it was possible to better understand the impact of a nonhomogeneous irradiation on photopolymerization process and thus, to tune the shape and the size of the final polymer objects. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3783–3794, 2008     

N‐alkoxypyridinium salts as coinitiators in radical polymerization: Synthesis and Photochemical Properties

A few N‐alkoxypyridinium salts are developed as photoinitiators for efficient polymerization reactions. They are characterized by absorption properties below 300 nm, and generate alkoxy radicals on UV‐Vis light exposure. The squarylium dye was used as a blue‐light photosensitizer. Polymerization results are correlated with the photochemistry of N‐alkoxypyridinium salts. The quenching of the excited singlet state of squarylium dye by pyridinium salt and the formation of the semioxidized species of squaraine suggests an electron transfer from an excited dye to a coinitiator, and that the resulting oxygen‐centered radical initiates the polymerization process. The chemical mechanism was investigated by steady state photolysis and nanosecond laser flash photolysis experiments. Photoinitiating activity of new photoinitiators for initiation of polymerization of trimethylolpropane triacrylate in the UV‐blue light region was compared with photoinitiating ability of selected commercially available initiators. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2840–2850     

Synthesis of amphiphilic graft copolymer brush and its use as template film for the preparation of silver nanoparticles

A microphase‐separated, amphiphilic graft copolymer consisting of a poly (vinyl chloride) (PVC) backbone and poly(oxyethylene methacrylate) (POEM) side chains, (PVC‐g‐POEM at 62:38 wt %) was synthesized via atom transfer radical polymerization (ATRP). Nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM) clearly revealed that the “grafting from” method using ATRP was successful and that the graft copolymer molecularly self‐assembled into discrete nanophase domains of continuous PVC and isolated POEM regions. The self‐assembled graft copolymer film was used to template the growth of silver nanoparticles in solid state by introducing a AgCF₃SO₃ precursor and a UV irradiation process. The in situ formation of silver nanoparticles in the graft copolymer template film was confirmed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering. FTIR spectroscopy and X‐ray photoelectron spectroscopy also demonstrated the selective incorporation and in situ formation of silver nanoparticles within the hydrophilic POEM domains, presumably due to strong interactions between the silver and the ether oxygen in POEM. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3911–3918, 2008     

Synthesis of well‐defined polymeric activated esters

Monomers bearing an activated ester group can be polymerized under various controlled polymerization techniques, such as ATRP, NMP, RAFT polymerization, or ROMP. Combining the functionalization of polymers via polymeric activated esters with these controlled polymerization techniques generate possibilities to realize highly functionalized polymer architectures. Within this highlight two different research areas of activated esters in polymer science will be discussed: (i) the preparation of defined reactive polymer architectures by controlled polymerization techniques and (ii) the preparation of defined reactive thin films. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6677–6687, 2008     

Synthesis and characterization of a novel polymer based on anthracene moiety for organic thin film transistor

We have designed and synthesized a new polymer, which could be used in the organic thin film transistor (OTFT). Poly[2,6‐bis(3′‐dodecythiophene‐2′‐yl)anthracene] (PDTAn), which is composed with anthracene moiety and dodecyl alkyl thiophene, was synthesized by oxidative polymerization using iron (III) chloride. The mole ratio of FeCl₃ and monomer (4.2:1), keeping low temperature during the initiation reaction, amount of solvent, and dropping order were very important for oxidative polymerization without crosslinking. The molecular weight of the polymer (M_w) was measured to be 40,000 with 2.85 of polydispersity index by GPC. The physical and optical properties of the polymer were characterized by differential scanning calorimetry (DSC), cyclic voltammetry (CV), and optical absorption and photoluminescence (PL) spectroscopy. A field‐effect mobility of 1.1 × 10^?4 cm² V^?1 S^?1, a current on/off ratio of 10⁵, and the V_th at ?15.2 V had been obtained for OTFTs using this polymer semiconductor by solution coating. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5115–5122, 2008     

Studies on the thermal polymerization of substituted benzoxazine monomers: Electronic effects

To evaluate the influence of the electronic effects on the polymerization temperature, we looked at several 3‐phenyl‐3,4‐dihydro‐2‐H‐1,3‐benzoxazine monomers with electron‐withdrawing or electron‐donating groups in the 6 and 4′ positions. The monomers were synthesized and characterized using different synthetic methods to achieve the best possible results. The thermal polymerization of these benzoxazine monomers was analyzed by differential scanning calorimetry, and the polymerization behavior and the polymer characteristics were related to the electronic character of the substituent and the polymerization mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3353–3366, 2008