Interfacial friction and adhesion of polymer brushes

A bead-probe lateral force microscopy (LFM) technique is used to characterize the interfacial friction and adhesion properties of polymer brushes. Our measurements attempt to relate the physical structure and chemical characteristics of the brush to their properties as thin-film, tethered lubricants. Brushes are synthesized at several chain lengths and surface coverages from polymer chains of polydimethylsiloxane (PDMS), polystyrene (PS), and a poly(propylene glycol)-poly(ethylene glycol) block copolymer (PPG/PEG). At high surface coverage, PDMS brushes manifest friction coefficients (COFs) that are among the lowest recorded for a dry lubricant film (μ ≈ 0.0024) and close to 1 order of magnitude lower than the COF of a bare silicon surface. Brushes synthesized from higher molar mass chains exhibit higher friction forces than those created using lower molar mass polymers. Increased grafting density of chains in the brush significantly reduces the COF by creating a uniform surface of stretched chains with a decreased surface viscosity. Brushes with lower surface tension and interfacial shear stresses manifest the lowest COF. In particular, PDMS chains exhibit COFs lower than PS by a factor of 3.7 and lower than PPG/PEG by a factor of 4.7. A scaling analysis conducted on the surface coverage (σ) in relation to the fraction (ε) of the friction force developing from adhesion predicts a universal relation ε ~ σ(4/3), which is supported by our experimental data.     

Effect of pendent chains on the interfacial properties of thin polydimethylsiloxane (PDMS) networks

The interfacial properties of end-linked polydimethylsiloxane (PDMS) films on silicon are examined. Thin cross-linked PDMS films (～10 μm thick) were synthesized over a self-assembled monolayer supported on a silicon wafer. By systematically varying the concentration of monofunctional PDMS in a mixture with telechelic precursor molecules, structures ranging from near-ideal elastic networks to poorly cross-linked networks composed of a preponderance of dangling/pendent chains were synthesized. Lateral force microscopy (LFM) employing bead probes was used to quantify the effect of network structure on the interfacial friction coefficient and residual force. Indentation measurements employing an AFM in force mode were used to characterize the elastic modulus and the pull-off force for the films as a function of pendent chain content. These measurements were complemented with conventional mechanical rheometry measurements on similar thick network films to determine their bulk rheological properties. All networks studied manifested interfacial friction coefficients substantially lower than that of bare silicon. PDMS networks with the lowest pendent chain content displayed friction coefficients close to 1 order of magnitude lower than that of bare silicon, whereas networks with the highest pendent chain content manifested friction coefficients about 3 times lower than that of bare silicon. At intermediate sliding velocities, a crossover in the interfacial friction coefficient was observed, wherein cross-linked PDMS films with the least amount of pendent chains exhibit the highest friction coefficient. These observations are discussed in terms of the structure of the films and relaxation dynamics of elastic strands and dangling chains in tethered network films.     

Interfacial friction and adhesion of cross-linked polymer thin films swollen with linear chains

The preparation and interfacial properties of a new type of tethered, thin-film lubricant coating are presented. These coatings are composed of three components: a dense self-assembled monolayer (SAM) underlayer that presents reactive vinyl groups at its surface; a cross-linked polydimethylsiloxane (PDMS) overlayer that is covalently tethered to the SAM; and free, mobile linear PDMS chains dispersed in the network. We investigate the influence of the molecular weight (Ms) and concentration of the free PDMS chains on the structure and equilibrium swelling properties of the cross-linked films. Using a bead-probe lateral force microscopy measurement technique, we also quantify the interfacial friction and adhesion characteristics of surfaces functionalized with these coatings. We find that both the volume fraction and the molecular weight of free PDMS molecules in the coatings influence their interfacial friction and adhesion properties. For example, the addition of short PDMS chains in dry, cross-linked PDMS thin films yields tethered surface coatings with ultralow friction coefficients (mu = 5.2 x 10(-3)). An analysis based on classical lubrication theory suggests that the reduction in friction force produced by free polymer is a consequence of the gradual separation of asperities on opposing surfaces and the consequent substitution of solid-solid friction by viscous drag of the free polymer chains in the network.     

Chains anisotropy in PDMS networks due to friction on gold surfaces

In this article, we describe an experimental friction study of poly(dimethyl siloxane) (PDMS) networks on metallic substrates such as gold-coated slides, and under different conditions. The friction generates a transfer of a thin layer of PDMS and a preferential orientation of the polymer chains at the interface. However, the characterization of this layer is complicated, given the small amount of matter and the contact with a metallic surface. The polarization-modulation infrared reflexion-absorption spectroscopy (PM-IRRAS), which is an excellent tool for anisotropy and orientation studies, was used to characterize the PDMS transferred layer. Our results showed an induced anisotropy due to the friction, and in which PDMS chains are lying parallel to the gold substrate surface. Our spectroscopic analyzes allowed us to imagine a scheme of PDMS transfer on the gold surface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2348–2353, 2004     

Permeability and thermal properties of PDMS/LDPE multilayer composite membranes

This work reports on the preparation and properties of polydimethylsiloxane (PDMS)/low‐density polyethylene (LDPE) multilayer composite polymer membranes (MCPM) for gas separation applications. The membranes were produced by combining sequential coating with melt‐extrusion/salt leaching techniques. In particular, the gas sorption and permeation properties at different pressure (40–90 psig) and temperature (27–55 °C) are reported with morphology and thermogravimetric properties. The results show that a 20 μm PDMS layer was able to penetrate the microporous LDPE surface layer substrate leading to improved interfacial adhesion. Based on the different gases (CO₂, CH₄, and C₃H₈) solubility, permeability, and diffusivity obtained, these membranes are seen as good candidates for industrial gas separations. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1045–1052     

Molecular simulation of the frictional behavior of polymer-on-polymer sliding

Molecular simulations of the sliding processes of polymer-on-polymer systems were performed to investigate the surface and subsurface deformations and how these affect tribological characteristics of nanometer-scale polymer films. It is shown that a very severe deformation is localized to a band of material about 2.5 nm thick at the interface of the polymer surfaces. Outside of this band, the polymer films experience a uniform shear strain that reaches a finite steady-state value of close to 100%. Only after the polymer films have achieved this steady-state shear strain do the contacting surfaces of the films show significant relative slippage over each other. Because severe deformation is limited to a localized band much thinner than the polymeric films, the thickness of the deformation band is envisaged to be independent of the film thickness and hence frictional forces are expected to be independent of the thickness of the polymer films. A strong dependency of friction on interfacial adhesion, surface roughness, and the shear modulus of the sliding system was observed. Although the simulations showed that frictional forces increase linearly with contact pressure, adhesive forces contribute significantly to the overall friction and must therefore be accounted for in nanometer-scale friction. It is also shown that the coefficient of friction is lower for lower-density polymers as well as for polymers with higher molecular weights.     

Step-growth synthesis and interfacial friction properties of surface dendron coatings

We report a new procedure for synthesizing self-assembled two-tiered coatings comprised of a tethered carbosilane dendron canopy layer over an alkylsilane sublayer. The sublayer is anchored to a silicon substrate, and the areal density of the canopy can be controlled by changing the concentration of reactive vinyl groups on the sublayer surface. The structure of the dendron layer is characterized by angle-resolved X-ray photoelectron spectroscopy (ARXPS), water contact angle, and ellipsometry. Steric hindrance due to close packing of functional groups has a strong effect on the reaction efficiency, and dendron structure can be obtained only in canopies with low areal densities. Lateral force microscopy (LFM) is used to study interfacial friction and adhesion properties of the coatings. Structural variations in the canopy layer are found to play a crucial role in interfacial friction properties of these coatings.     

Polyimide polydimethylsiloxane triblock copolymers for thin film composite gas separation membranes

This article demonstrates the successful fabrication of thin‐film‐composite (TFC) membranes containing well‐defined soft‐hard‐soft triblock copolymers. Based on “hard” polyimide (PI) and “soft” polydimethylsiloxane (PDMS), these triblock copolymers (PDMS‐b‐PI‐b‐PDMS), were prepared via condensation polymerization, and end‐group allylic functionalization to prepare the polyimide component and subsequent “click” coupling with the soft azido functionalized PDMS component. The selective layer consisted of pure PDMS‐b‐PI‐b‐PDMS copolymers which were cast onto a precast crosslinked‐PDMS gutter layer which in turn was cast onto a porous polyacrylonitrile coated substrate. The TFC membranes' gas transport properties, primarily for the separation of carbon dioxide (CO₂) from nitrogen (N₂), were determined at 35 °C and at a feed pressure of 2 atm. The TFC membranes showed improvements in gas permselectivity with increasing PDMS weight fraction. These results demonstrate the ability for glassy, hard polymer components to be coated onto otherwise incompatible surfaces of highly permeable soft TFC substrates through covalent coupling. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3372–3382     

Synthesis of thermally degradable epoxy adhesives

We have developed a new strategy for the synthesis of epoxide‐containing polymers where the pendant reactive groups are connected to the main backbone via thermally labile oxonorbornene groups. The polymers were synthesized by radical 1,4‐polymerization of the appropriate bicyclic diene monomer. The produced polymers can be crosslinked in the presence of a diamine and de‐crosslinked by thermal treatment at 160 °C, which induces retro‐Diels–Alder reaction and cleaves pendant groups from the polymer backbone, as confirmed by differential scanning calorimetry. The potential for the utilization of this polymer as a thermally removable adhesive was demonstrated by a simple adhesion test. This method provides access to thermally cleavable epoxy networks that can be quickly and irreversibly disintegrated into nonvolatile components upon heating to a specified temperature. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4992–4997     

Supercrystal structures of polyhedral PbS nanocrystals

We analyzed the interaction between chemically grafted polysaccharide layers in aqueous solutions. To fabricate such layers, an end-terminated dextran silane coupling agent was synthesized and the polydextran was grafted to oxidized silicon wafers and to silica particles. This resulted in the formation of a 28 nm thick layer (in air) and a grafted amount of 40 mg/m(2) as determined by ellipsometry. The physical properties of the grafted layer were investigated in aqueous solutions by atomic force microscope imaging and colloidal probe force measurements. Surface and friction forces were measured between one bare and one polydextran coated silica surface. A notable feature was a bridging attraction due to affinity between dextran and the silica surface. Surface interactions and friction forces were also investigated between two surfaces coated with grafted polydextran. Repulsive forces were predominant, but nevertheless a high friction force was observed. The repulsive forces were enhanced by addition of sodium dodecyl sulfate (SDS) that associates with the tethered polydextran layers. SDS also decreased the friction force. Our data suggests that energy dissipation due to shear-induced structural changes within the grafted layer is of prime importance for the high friction forces observed, in particular deformation of protrusions in the surface layer.     

Effect of rate retardation in RAFT grafting polymerization from silicon wafer surface

Polystyrene and poly(butyl acrylate) were grafted from silicon wafer surface by reversible addition‐fragmentation chain transfer (RAFT) polymerization. Three RAFT agents were immobilized onto silicon wafer through their leaving/initiating groups (R group). Grafting polymerization of butyl acrylate (BA) and styrene (St) was then carried out from the immobilized RAFT agents. The immobilization of the RAFT agents and the subsequent grafting polymerization of St and BA were evaluated by ellipsometry and X‐ray photoelectron spectroscopy. It was found that type of monomer, structure of RAFT agent, and local RAFT concentration on the surface have dramatic influences on the thickness of grafted polymer layer. The grafting polymerization with more severe rate retardation effect yielded thinner polymer films on the silicon wafer. Selection of a RAFT agent with little rate retardation was critical in the grafting polymerization to achieve thick films. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 970–978, 2008     

XPS and resistive studies on thin films of a copper(II)‐based coordination polymer deposited on functionalized interdigital electrodes

A symmetrical 2‐thiopyrimidine based molecule with an expanded π‐electron system is synthesized and used to form a self‐assembled monolayer (SAM) on gold surfaces. Utilizing chemical vapor deposition a monolayer of (3‐mercaptopropyl)triethoxysilane is formed on silicon dioxide substrates. Both of these SAM coated substrates are characterized by X‐ray photoelectron spectroscopy and the growth of a coordination polymer built up from 5,5′‐(ethyne‐1,2‐diyl)bis(2‐hydroxyacetophenone) and copper(II) on dual SAM coated transducers is studied. After the deposition procedure on interdigital electrodes the electrical properties of the polymer are investigated performing resistive measurements. A significant change of the resistance, which depends on the surrounding atmosphere, proves the sensing behavior of the synthesized coordination polymer. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 335–344     

Diazonium salts for surface‐confined visible light radical photopolymerization

The surface chemistry of aryl diazonium salts has progressed at a remarkable pace in the last two decades, and opened many avenues in materials science. These compounds are excellent coupling agents for polymers to surfaces via several surface‐confined polymerization methods. For the first time, we demonstrate that diazonium salts are efficient for surface initiating radical photopolymerization in the visible light of methyl methacrylate (MMA) and 2‐hydroxyethyl methacrylate (HEMA) taken as model monomers. To do so, 4‐(dimethylamino)benzenediazonium salt was electroreduced on gold plates or flexible ITO sheets to provide 4‐(dimethylamino)phenyl (DMA) hydrogen donor layers; while excited state camphorquinone acted as the free hydrogen abstractor. In the same way, we co‐polymerized HEMA and MMA with ethylene glycol dimethacrylate in order to obtain crosslinked polymer grafts. We demonstrate by XPS that gold was efficiently screened by the polymer layers and that the wettability of the surfaces accounts for the hydrophilic or hydrophobic characters of the tethered polymers. Homo‐ and crosslinked PMMA grafts were found to resist removal by the paint stripper methyl ethyl ketone. The grafted DMA/camphorquinone system operating in the visible light holds great promises in terms of adhesion of in situ designed continuous or patterned polymer coatings on various substrates. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3506–3515     

Scratching behavior of elastomeric poly(dimethylsiloxane) coatings

Scratch testing has been performed on elastomeric poly(dimethylsiloxane) (PDMS) coatings on stainless steel with a spherical indenter. The friction coefficient (horizontal‐to‐normal force ratio) during scratching decreases with increasing normal load. This result can be explained by assuming that during scratching the contact area is determined by elastic deformation and the horizontal force is proportional to the contact area. With increasing driving speed, the friction coefficient increases, but the rate of increase decreases; this suggests that the scratching of the PDMS coating is a rate process and that the viscoelastic property of the coating influences its frictional behavior. Below a critical normal load, which increases with the coating thickness, the PDMS coating recovers elastically after being scratched so that there are no scratch marks left behind. Above the critical normal load, the coating is damaged by a combination of delamination at the coating/substrate interface and through‐thickness cracking. When the coating is damaged, there is an increase in the friction coefficient, and the friction force displays significant fluctuations. Furthermore, the critical normal load increases with the driving speed; this implies that time is needed to nucleate damage. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1530–1537, 2002     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

Amphiphilic and hydrophobic surface patterns generated from hyperbranched fluoropolymer/linear polymer networks: Minimally adhesive coatings via the crosslinking of hyperbranched fluoropolymers

Hyperbranched fluoropolymers (HBFPs), based on benzyl ether linkages and having a large number of pentafluorophenyl chain ends, were crosslinked by a reaction with diamino-terminated poly(ethylene glycol) (PEG) or diamino-terminated poly(dimethyl siloxane) (PDMS) to form hyperbranched–linear copolymer networks of different compositions, structures, and properties. The crosslinking reactions involved the nucleophilic aromatic substitution of the pentafluorophenyl para-fluorines of HBFP by the amine functionalities of the respective telechelic linear segments. The contact angles, differential scanning calorimetry, thermogravimetric analysis, tensile measurements, and atomic force microscopy (AFM) were used to characterize the resulting network film samples. The surface wettability of the crosslinked materials was affected by the nature and amount of the linear polymer crosslinking agent employed. Amphiphilic polymer networks were formed by the incorporation of diamino-terminated PEG as a crosslinker, whereas diamino-terminated PDMS produced polymer networks of a hydrophobic character. The mechanical properties improved upon crosslinking, as measured by tensile testing. The mechanical integrity of the films was also found to improve upon crosslinking, as measured by AFM machining protocols. The AFM images revealed topographical morphologies that appeared to be the result of phase segregation of HBFP from PEG or PDMS; the dimensions of the phase-segregated domains were dependent on the stoichiometry of HBFP to the linear polymer and the thickness of the coating. As the content of PEG increased, fouling by human fibrinogen, used as a model protein, decreased. Further studies are in progress to determine the effects of the surface composition, morphology, and topography on the biofouling characteristics. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3531–3540, 2003     

Selective retention of some polyaromatic hydrocarbons by highly crosslinked polymer networks

Highly crosslinked polymer networks were characterized in terms of structural differences based on the crosslinked network structures with their chromatographic molecular retentivity for some polyaromatic hydrocarbons (PAHs). Because PAHs and some sterically bulky solutes were used in the chromatographic characterization, tiny differences in the crosslinked polymer networks were observed in terms of the chromatographic molecular retentivity. Ethylene dimethacrylate afforded molecular retentivity for anthracene, and this recognition ability changed with the polymerization time. In addition, 1,4‐butanediol dimethacrylate afforded molecular retentivity for pyrene, and this retentivity was larger than that for anthracene. The polymerization methods also affected the resulting polymer networks drastically. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2556–2566, 2005     

Synthesis,characterization, and permeability evaluation of hybrid organic–inorganic films

The preparation and characterization of hybrid organic–inorganic films based on poly(dimethylsiloxane), PDMS, crosslinked with nanoclusters obtained from pentaerythrithol triacrylate (PETA) and 2‐aminoethyl‐3‐aminopropyltrimethoxysilane (AS), are reported. The introduction of silica nanoclusters, obtained from tetraethoxysilane as an additional crosslinker, improved the mechanical stability of the films and also produced a noticeable decrease in the solvent sorption and in the distance between the nodes of the polymeric networks. The performance of these films as membranes for gas separation processes was similar to those reported for commercial PDMS, although they presented polar organic PETA/AS crosslinker nuclei. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4281–4292, 2004     

Densely crosslinked polycarbosiloxanes. II: Thermal and mechanical properties

The thermal and mechanical properties of two densely crosslinked polycarbosiloxane systems were investigated in relation to the molecular structure. The networks were prepared from functional branched prepolymers and crosslinked via a hydrosilylation curing reaction. The prepolymers having only vinyl functionalities (poly[phenylmethylvinyl]siloxanes) were crosslinked by using crosslinking agents with reactive silicon–hydrogen groups. In prepolymers having both silicon–vinyl and silicon–hydrogen groups (poly[phenylmethylvinylhydro)]siloxanes crosslinking took place intermolecularly. The thermal and mechanical properties of the polymer networks were found to be dependent on the phenyl  Si O_3/2 (branches) content in the prepolymer, the number of elastically effective crosslinks, the elastically effective network chain density and molecular weight between crosslinks, length of the chain segments introduced by the hydrosilylation crosslinking reaction, and the number of dangling ends. As a consequence of the dense crosslinking, the mechanical properties were also strongly dependent on the glass transition temperature. A tough–brittle transition was observed around the glass transition temperature of the polymer networks. The properties of the poly(phenylmethylvinylhydro)siloxane networks were found to be superior to those of the poly(phenylmethylvinyl)siloxane networks. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1311–1331, 1997     

Adhesion and friction of PDMS networks: molecular weight effects

The objective of this work is to find relations between adherence and friction behaviors of elastomer networks. The chosen approach is based on the parallel study of the initial molecular weight (i.e., the degree of cross-linking) dependence of both adherence and friction. The polymers used are cross-linked polydimethylsiloxane (PDMS) and the substrate is a smooth glass plate. The experimental procedure uses both friction (pin on disk tribometer) and adhesion (tack test) measurements, associated with surface analysis and mechanical and rheological characterizations. Tack results show that high molecular weight PDMS exhibits the greater adherence energy. This can be explained by the role of both chain length and free and pendant chains: more numerous and longer free chains favor the substrate wetting (at a molecular scale) and increases the energy dissipation during separation (extraction and reptation mechanisms). However, friction results indicate a higher friction resistance for low molecular weight PDMS. This result could be quite surprising. An explanation based on interfacial sliding properties of free and pendant chains can be proposed. Elsewhere, for the lower molecular weight polymer, elastic contact present during friction is able to act as a forced wetting, constraining the network and consequently leading to a greater energy dissipation.