Synthesis and characterization of photocrosslinked poly(ε‐caprolactone)s showing shape‐memory properties

Poly(ε‐caprolactone) (PCL) with a pendent coumarin group was prepared by solution polycondensation from 7‐(3,5‐dicarboxyphenyl) carbonylmethoxycoumarin dichloride and α, ω‐dihydroxy terminated poly(ε‐caprolactone) with molecular weights of 1250, 3000, and 10,000 g/mol. These photosensitive polymers underwent a rapid reversible photocrosslinking upon exposure to irradiation with alternating wavelengths (>280/254 nm) without a photoinitiator. The thermal and mechanical properties of the photocrosslinked films were examined by means of differential scanning calorimetry and stress–strain measurements. The crosslinked films exhibited elastic properties above the melting temperature of the PCL segment along with significant decrease in the ultimate tensile strength and Young's modulus. Shape‐memory properties such as strain fixity ratio (R_f) and strain recovery ratio (R_r) were determined by means of a cyclic thermomechanical tensile experiments under varying maximum strains (ε_m = 100, 300, and 500%). The crosslinked ICM/PCL‐3000 and ‐10,000 films exhibited the excellent shape‐memory properties in which both R_f and R_r values were 88–100% for tensile strain of 100–500%; after the deformation, the films recovered their permanent shapes instantaneously. In vitro degradation was performed in a phosphate buffer saline (pH 7.2) at 37 °C with or without the presence of Pseudomonas cepacia lipase. The presence of the pendent coumarin group and the crosslinking of the polymers pronouncedly decreased the degradation rate. The crosslinked biodegradable PCL showing a good shape‐memory property is promising as a new material for biomedical applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2422–2433, 2009     

A novel shape memory poly(ε‐caprolactone) network via UV‐triggered thiol‐ene reaction

A facile method to prepare shape memory polymers crosslinked by SiO₂ is described. A series of biodegradable shape memory networks were obtained through thiol‐ene reaction triggered by UV irradiation between surface‐thiol‐modified SiO₂ nanoparticles and end‐acrylate poly (ε‐caprolactone) (PCL). The highly selective thiol‐ene reaction ensured a uniform distribution of PCL chains between crosslinkers, contributing well‐defined network architecture with enhanced mechanical and shape‐memory properties. Thiol‐functionalized silica nanoparticle was characterized by using FTIR and XPS analysis, and ¹H NMR spectra was used to confirm the successful modification of terminal hydroxyl group of PCL diol. Surface‐modified silica particles were found well dispersible in acrylate‐capped PCL supported by SEM. Thermal and crystalline behaviors of the obtained polymers were analyzed by DSC and XRD, and DMA measurement proved good mechanical property. The shape memory behavior and tensile strength was somewhat tunable by the length of PCL. Acceptably, sample SiO₂‐SMP2k presented 99% recovery ratio and 97% shape fixity, and its relatively high tensile strength showed an attractive potential for biomedical application. Finally, a possible molecular mechanism accounting for the shape memory property was illustrated. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 692–701     

Impact of poly(ɛ‐caprolactone) architecture on the thermomechanical and shape memory properties

We report the synthesis of linear‐ and brush‐type poly(?‐caprolactone) (PCL) networks and investigate their thermal, mechanical, and shape memory behavior. Brush‐PCLs are prepared by ring‐opening metathesis polymerization (ROMP) of a norbornenyl‐functionalized ?‐caprolactone macromonomer (MM‐PCL) of different molecular weights. The linear analog, diacrylate end‐functionalized PCL (linear‐PCL), having comparable molecular weight of side chain of brush‐PCL is also synthesized. These polymers are thermally cured by a radical initiator in the presence of poly(ethylene glycol) diacrylate crosslinker. Thermal and linear viscoelastic properties as well as shape memory performance of the resulting PCL networks are investigated, and are significantly impacted by the PCL architecture. Therefore, our work highlights that tailoring macromolecular architecture is useful strategy to manipulate thermal, mechanical, and resulting shape memory properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3424–3433     

Synthesis and properties of photocurable biodegradable multiblock copolymers based on poly(ε‐caprolactone) and poly(L‐lactide) segments

Photocurable biodegradable multiblock copolymers were synthesized from poly(ε‐caprolactone) (PCL) diol and poly(L ‐lactide) (PLLA) diol with 4,4′‐(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender derived from adipoyl chloride and 4‐hydroxycinnamic acid, and they were characterized with Fourier transform infrared and ¹H NMR spectroscopy, gel permeation chromatography, wide‐angle X‐ray diffraction, differential scanning calorimetry, and tensile tests. The copolymers were irradiated with a 400‐W high‐pressure mercury lamp from 30 min to 3 h to form a network structure in the absence of photoinitiators. The gel concentration increased with time, and a concentration of approximately 90% was obtained in 90–180 min for all the films. The photocuring hardly affected the crystallinity and melting temperature of the PCL segments but reduced the crystallinity of the PLLA segments. The mechanical properties, such as the tensile strength, modulus, and elongation, were significantly affected by the copolymer compositions and gel concentrations. Shape‐memory properties were determined with cyclic thermomechanical experiments. The CAC/PCL and CAC/PCL/PLLA (75/25) films photocured for 30–120 min showed good shape‐memory properties with strain fixity rates and recovery rates of approximately 100%. The formation of the network structure and the crystallization and melting of the PCL segments played very important roles for the typical shape‐memory properties. Finally, the degradation characteristics of these copolymers were investigated in a phosphate buffer solution at 37 °C with proteinase‐k and Pseudomonas cepacia lipase. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2426–2439, 2005     

Shape‐memory effect in hyperbranched poly(ethyleneimine)‐modified epoxy thermosets

A series of shape‐memory epoxy thermosets were synthesized by crosslinking diglycidyl ether of bisphenol A with mixtures of commercially available hyperbranched poly(ethyleneimine) and polyetheramine. Thermal, mechanical and shape‐memory properties were studied and the effect on them of the content and structure of the hyperbranched polymer was discussed. Measurements showed that the glass transition temperature can be tailored from 60 °C to 117 °C depending on the hyperbranched polymer content, and all formulations showed an appropriate glassy/rubbery storage modulus ratio. Shape‐memory programming was carried out at TgE′ given the excellent mechanical properties of the materials, with maximum stress and failure strain up to 15 MPa and 60%, respectively. The resulting shape‐memory behavior was excellent, with maximum shape recovery and shape fixity of 98% as well as a fast shape‐recovery rate of 22%/min. The results show that hyperbranched poly(ethyleneimine) as a crosslinking agent can be used to enhance mechanical and shape‐memory properties with different effects depending on the crosslinking density. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 924–933     

Effect of comonomer on thermal/mechanical and shape memory property of L‐lactide‐based shape‐memory copolymers

In this study, three kinds of L ‐lactide‐based copolymers, poly(lactide‐co‐glycolide) (PLGA), poly(lactide‐co‐p‐dioxanone) (PLDON) and poly(lactide‐co‐caprolactone) (PLC), were synthesized by the copolymerization of L ‐lactide (L) with glycolide (G), or p‐dioxanone (DON) or ε‐caprolactone (CL), respectively. The copolymers were easily soluble in common organic solvents. The compositions of the copolymers were determined by ¹H‐NMR. Thermal/mechanical and shape‐memory properties of the copolymers with different comonomers were compared. Moreover, the effect of the chain flexibility of the comonomers on thermal/mechanical and shape‐memory properties of the copolymers were investigated. The copolymers with appropriate lactyl content showed good shape‐memory properties where both the shape fixity rate (R_f)and the shape recovery rate (R_r) could exceed 95%. It was found that the comonomers with different flexible molecular chain have different effects on their thermal/mechanical and shape‐memory properties. Among them, PLGA has the highest mechanical strength and recovery rate while PLC copolymer has high recovery rate when the lactyl content exceeded 85% and the lowest transition temperature (T_trans). Copyright © 2007 John Wiley & Sons, Ltd.     

Influence of programming strain rates on the shape‐memory performance of semicrystalline multiblock copolymers

Multiblock copolymers named PCL‐PIBMD consisting of crystallizable poly(ε‐caprolactone) segments and crystallizable poly[oligo(3S‐iso‐butylmorpholine‐2,5‐dione)] segments coupled by trimethyl hexamethylene diisocyanate provide a versatile molecular architecture for achieving shape‐memory effects (SMEs) in polymers. The mechanical properties as well as the SME performance of PCL‐PIBMD can be tailored by the variation of physical parameters during programming such as deformation strain or applied temperature protocols. In this study, we explored the influence of applying different strain rates during programming on the resulting nanostructure of PCL‐PIBMD. Programming was conducted at 50 °C by elongation to ε_m = 50% with strain rates of 1 or 10 or 50 mm min^?1. The nanostructural changes were visualized by atomic force microscopy (AFM) measurements and investigated by in situ wide and small angle X‐ray scattering experiments. With increasing the strain rate, a higher degree of orientation was observed in the amorphous domains. Simultaneously the strain‐induced formation of new PIBMD crystals as well as the fragmentation of existing large PIBMD crystals occurred. The observed differences in shape fixity ratio and recovery stress of samples deformed with various strain rates can be attributed to their different nanostructures. The achieved findings can be relevant parameters for programming the shape‐memory polymers with designed recovery forces. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1935–1943     

Compatibilized poly(ϵ‐caprolactone)/poly(L‐lactide) blends for biomedical uses

A binary poly(L ‐lactide)/poly(ε‐caprolactone) (PLLA/PCL) (70/30 w/w) blend and a ternary PLLA/PCL/PLLA‐PCL‐PLLA blend of the same composition which contains 4 wt.‐% of a triblock PLLA‐PCL‐PLLA copolyester as compatibilizing agent were prepared by melt mixing at 200°C. Investigation of the thermal and mechanical properties of the blends and scanning electron microscopy of their fracture surfaces showed in the case of the ternary blend a better state of dispersion of PCL in the PLLA matrix and an improved toughness.     

Recovery stress and work output in hyperbranched poly(ethyleneimine)‐modified shape‐memory epoxy polymers

In this study a series of hyperbranched modified shape‐memory polymers were subjected to constrained shape recoveries in order to determine their potential use as thermomechanical actuators. Materials were synthesized from a diglycidyl ether of bisphenol A as base epoxy and a polyetheramine and a commercial hyperbranched poly(ethyleneimine) as crosslinker agents. Hyperbranched polymers within the structure of the shape‐memory epoxy polymers led to a more heterogeneous network that can substantially modify mechanical properties. Thermomechanical and mechanical properties were analyzed and discussed in terms of the content of hyperbranched polymer. Shape‐memory effect was analyzed under fully and partially constrained conditions. When shape recovery was carried out with fixed strain a recovery stress was obtained whereas when it was carried out with a constraining stress the material performs mechanical work. Tensile tests at Tg^E′ showed excellent values of stress and strain at break (up to 15 MPa and almost 60%, respectively). Constrained recovery performances revealed rapid recovery stress generation and unusually high recovery stresses (up to 7 MPa) and extremely high work densities (up to 750 kJ/m³). The network structure of shape‐memory polymers was found to be a key factor for actuator‐like applications. Results confirm that hyperbranched modified‐epoxy shape memory polymers are good candidates for actuator‐like shape‐memory applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1002–1013     

Thermo‐/moisture‐responsive shape‐memory effect of poly(2‐ethyl‐2‐oxazoline) networks

In this work, poly(2‐ethyl‐2‐oxazoline) (PEtOx) is crosslinked to realize a moisture‐ and thermo‐responsive shape‐memory polymer. The obtained PEtOx networks exhibit excellent shape‐memory properties with storable strains of up to 650% and recovery values of 100% over at least 10 shape‐memory cycles. The trigger temperature (T_trig) of 68 °C of a PEtOx network at a relative humidity (RH) of 0% decreases with increasing moisture and equals room temperature at an RH of 40%. Thus, programmed PEtOx networks trigger sensitively on a certain temperature/moisture combination and, further, can be programmed as well as triggered at room temperature exclusively by varying humidity. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1053–1061     

Shape memory behavior of carbon nanotube‐reinforced trans‐1,4‐polyisoprene and low‐density polyethylene composites

Shape memory composites of trans‐1,4‐polyisoprene (TPI) and low‐density polyethylene (LDPE) with easily achievable transition temperatures were prepared by a simple physical blending method. Carbon nanotubes (CNTs) were introduced to improve the mechanical properties of the TPI/LDPE composites. The mechanical, cure, thermal, and shape memory properties of the TPI/LDPE/CNTs composites were investigated in this study. In these composites, the cross‐linked network generated in both the TPI and LDPE portions acted as a fixed domain, while the crystalline regions of the TPI and LDPE portions acted as a domain of reversible shape memory behavior. We found that CNTs acted as not only reinforced fillers but also nucleation agents, which improved the crystalline degree of the TPI and LDPE portions of the composites. Compared with the properties at the other CNT doses, the mechanical properties of the TPI/LDPE composites when the CNT dose was 1 phr were improved significantly, showing excellent shape memory properties (R_f = 97.85%, R_r = 95.70%).     

Biodegradable thermoset shape‐memory polymer developed from poly(β‐amino ester) networks

The purpose of this study was to develop a degradable thermoset shape‐memory polymer from poly(β‐amino ester) (PBAE) networks. PBAE was chosen to be the crosslinker as it is biodegradable and has been projected as a potential material for biomedical applications. The low glass transition temperature of PBAE was increased to a biomedically relevant range using methyl methacrylate and methyl acrylate as the linear chain builders. The thermo‐mechanical properties of the networks were tailored such that they exhibited onset of glass transition temperature in between the room temperature (22 °C) and the body temperature (37 °C). Free‐strain recovery tests under heating and isothermal conditions were performed to quantify shape‐memory behavior. Testing showed that sampled programmed at 10 °C initiated deformation recovery at a lower temperature and a faster rate as compared to programming at 60 °C. Higher thermal conductivity of water enabled the samples to recover faster in water than in air. Samples with higher PBAE crosslinking densities exhibited higher normalized mass loss under regular and accelerated conditions. The amount of water absorption in the networks also increased with the crosslinker concentration independent of the testing conditions. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Thermoreversibly Crosslinked Poly(ε‐caprolactone) as Recyclable Shape‐Memory Polymer Network

A new concept to build shape memory polymers (SMP) combining outstanding fixity and recovery ratios (both above 99% after only one training cycle) typical of chemically crosslinked SMPs with reprocessability restricted to physically crosslinked SMPs is demonstrated by covalently bonding, through thermoreversible Diels–Alder (DA) adducts, star‐shaped poly(ε‐caprolactones) (PCL) end‐functionalized by furan and maleimide moieties. A PCL network is easily prepared by melt‐blending complementary end‐functional star polymers in retro DA regime, then by curing at lower temperature to favour the DA cycloaddition. Such covalent network can be reprocessed when heated again at the retro DA temperature. The resulting SMP shows still excellent shape memory properties attesting for its good recyclability.

     

Semi‐interpenetrating polymer networks composed of diisocyanate‐bridged 4‐arm star‐shaped l‐lactide oligomers and poly(ε‐caprolactone)

Semi‐interpenetrating polymer networks (semi‐IPNs) were prepared by reactions of 2,4‐tolylene diisocyanate (TDI) and hydroxy‐terminated 4‐arm star‐shaped l ‐lactide oligomers (H4LAO_n's) with the degrees of polymerization of lactate unit per one arm, n = 3, 5, and 10 in the presence of poly(ε‐caprolactone) (PCL). Morphologies, thermal, and mechanical properties of the TDI‐bridged H4LAO_n (TH4LAO_n)/PCL semi‐IPNs were evaluated by comparing with those of poly(l ‐lactide) (PLA)/PCL blends. Compatibility between the two components of the TH4LAO_n/PCL semi‐IPN with a PCL content not more than 50 wt % was much better than those of the PLA/PCL blends with the same PCL content. All the TH4LAO_n networks were substantially amorphous and their tan δ peak or glass transition temperatures increased with decreasing n value. Most of the semi‐IPNs did not show clear glass transition temperature related to both the components. Tensile toughness and elongation at break for all the TH4LAO_n/PCL semi‐IPNs were much higher than those for the PLA/PCL blends with the same PCL content. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1420–1428     

Electrospun poly(ε‐caprolactone)‐based composites using synthesized β‐tricalcium phosphate

Non‐woven hybrid membranes based on poly(ε‐caprolactone) (PCL) and as‐synthesized β‐tricalcium phosphate (β‐TCP) were obtained by the electrospinning technique. A wide range of composition was investigated, the filler content spanning between 2 and 60 wt%. The synthesis of the β‐TCP powder was accomplished by titration of calcium hydroxide with phosphoric acid followed by calcination of the resulting precipitate at 1100°C. The as‐dried calcium phosphate was characterized by Inductive Coupled Plasma (AES‐ICP), thermal analysis (TG‐DTA), Fourier Transform Infrared Spectroscopy (FT‐IR), Scanning Electron Microscopy (SEM), and high temperature X‐ray diffraction analysis (HT‐XRD). The specific surface area (SSA) was evaluated by N₂ adsorption. Microstructure of PCL/TCP membranes was investigated by SEM, energy dispersion spectroscopy (EDS), XRD analysis, and SSA measurements. The average fiber diameter ranged between 1 and 2 µm, the porosity was 80–90%, and the SSA 16 m²/g. Mechanical properties were determined by uniaxial tensile test. A remarkable enhancement of the tensile modulus was observed for composites containing up to 4 wt% β‐TCP. The ultimate tensile strength ranged between 2 and 3 MPa for samples loaded up to 8 wt%. For most of the samples, the elongation at break was in the range 100–150%. Copyright © 2010 John Wiley & Sons, Ltd.     

Organic‐montmorillonite modified shape memory epoxy composite

A series of organic‐montmorillonite (OMMT) modified shape memory epoxy (SMEP) composites were prepared for the purpose of application on space deployable structures. Tensile test, dynamic mechanical analysis (DMA), X‐ray diffraction (XRD), scanning electron microscope (SEM), and fold‐deploy shape memory test methods were used to characterize the mechanical, structure, and shape memory properties of these materials. The results showed addition of OMMT could improve the composites' toughness, tensile strength, transition temperature, and shape recovery speed, while shape recovery ratio was unaffected. Composite with 3wt%. OMMT had the optimum combination property. It could fully recover its original shape in about 2 min at 185°C under the maximum bending angle of 180°. Its elongation at break and tensile strength were increased by 835 and 17.4%, respectively, compared to that of neat SMEP. The transition temperature also slightly increased. Copyright © 2010 John Wiley & Sons, Ltd.     

Click coupled graphene for fabrication of high‐performance polymer nanocomposites

An effective technique of using click coupled graphene to obtain high‐performance polymer nanocomposites is presented. Poly(ε‐caprolactone) (PCL)‐click coupled graphene sheet (GS) reinforcing fillers are synthesized by the covalent functionalization of graphene oxide with PCL, and subsequently the PCL‐GS as a reinforcing filler was incorporated into a shape memory polyurethane matrix by solution casting. The PCL‐click coupled GS has shown excellent interaction with the polyurethane matrix, and as a consequence, the mechanical properties, thermal stability, thermal conductivity, and thermo‐responsive shape memory properties of the resulting nanocomposite films could be enhanced remarkably. In particular, for polyurethane nanocomposites incorporated with 2% PCL‐GS, the breaking stress, Young's modulus, elongation‐at‐break, and thermal stability have been improved by 109%, 158%, 28%, and 71 °C, respectively. This click coupling protocol offers the possibility to fully combine the extraordinary performance of GSs with the properties of polyurethane. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Preparation and characterization of biodegradable poly(lactic acid)‐ block‐poly(ε‐caprolactone) multiblock copolymer

Biodegradable copolymers of poly(lactic acid)‐block‐poly(ε‐caprolactone) (PLA‐b‐PCL) were successfully prepared by two steps. In the first step, lactic acid monomer is oligomerized to low molecular weight prepolymer and copolymerized with the (ε‐caprolactone) diol to prepolymer, and then the molecular weight is raised by joining prepolymer chains together using 1,6‐hexamethylene diisocyanate (HDI) as the chain extender. The polymer was carefully characterized by using ¹H‐NMR analysis, gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR). The results of ¹H‐NMR and TGA indicate PLA‐b‐PCL prepolymer with number average molecular weights (M_n) of 4000–6000 were obtained. When PCL‐diols are 10 wt%, copolymer is better for chain extension reaction to obtain the polymer with high molecular weight. After chain extension, the weight average molecular weight can reach 250,000 g/mol, as determined by GPC, when the molar ratio of –NCO to –OH was 3:1. DSC curve showed that the degree of crystallization of PLA–PCL copolymer was low, even became amorphous after chain extended reaction. The product exhibits superior mechanical properties with elongation at break above 297% that is much higher than that of PLA chain extended products. Copyright © 2009 John Wiley & Sons, Ltd.     

Aligned poly (glycolide‐lactide) fiber membranes with conducting polypyrrole

Electroactive polypyrrole (PPy) are highly attractive for a number of biomedical applications such as tissue engineering. To improve interfacial compatibility of PPy with biopolyesters, poly (?‐caprolactone) grafted PPy (PPy‐g‐PCL) are synthesized in this work and characterized with Fourier transform infrared and nuclear magnetic resonance. PPy‐g‐PCL exhibits good conductivity and electrochemical activity. It is also blended with poly (glycolide‐lactide) to make aligned fiber membranes via drum at the speed of 1500 r/min. The relationships of blending ratio with the fibrous structure, thermal stability, wettability, and mechanical properties are clarified. The results show that blending PPy‐g‐PCL has no significant effect on the fibrous morphology, but fibers trends aligned architecture as the blend ratio of poly (glycolide‐lactide)/PPy‐g‐PCL exceeds 70/30. The membranous thermal and mechanical stability are modified. The membranous hydrophilicity significantly enhances with PPy‐g‐PCL amount increasing. Then the fiber membrane with topographical and electrical cues is qualified as the application of tissue engineering. Copyright © 2016 John Wiley & Sons, Ltd.     

High modulus ratio shape‐memory polymers achieved by combining hydrogen bonding with controlled crosslinking

A new type of poly(methyl acrylate)‐co‐(acrylic acid) (PMA‐AA) networks obtained by combining hydrogen bonding with controlled crosslinking exhibit full and rapid shape‐memory recovery. The structure, thermal properties, dynamical mechanical properties and shape‐memory effects of these networks were presented. High modulus ratios were achieved for the series of PMA‐AA networks based on intense self‐complementary hydrogen bonding in poly(acrylic acid) (PAA) segments. This lead to excellent shape‐memory effects with strain‐recovery ratio above 99%. Meanwhile, faster recovery speed was achieved by the synergistic effect of hydrogen bonding and controlled crosslinking compared to the linear PMA‐AA copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1241–1245, 2011