Proton transport in polybenzimidazole blended with H3PO4 or H2SO4

Proton transport in H₃PO₄‐ and H₂SO₄‐blended polybenzimidazoles (PBIs) has been studied with both temperature‐ and pressure‐dependent dielectric spectroscopy. The influences of the acid concentration and temperature on the relative conductance and activation volume are discussed. An Arrhenius relation is used to model the temperature‐dependent conductivity at a constant acid content. The logarithm of the relative conductance for PBI blended with H₃PO₄ decreases linearly with increasing pressure. As the temperature increases, the activation volume becomes smaller for PBI blended with H₃PO₄. It is proposed that proton transport in acid‐blended PBI is mainly controlled by proton hopping and diffusion rather than a mechanism mediated by the segmental motions in the polymer. The conductivities of PBIs blended with H₃PO₄ and H₂SO₄ are compared. At a 1.45 molar acid doping concentration, the former has the higher conductivity. With water, the conductivity of H₃PO₄‐blended PBI increases significantly. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 663–669, 2002; DOI 10.1002/polb.10132     

Synthesis and self‐association behavior of poly[bis(2‐(2‐methoxyethoxy)ethoxy)phosphazene]‐b‐poly(propyleneglycol) triblock copolymers

Amphilic triblock copolymers with varying ratios of hydrophilic poly[bis (methoxyethoxyethoxy)phosphazene] (MEEP) and relatively hydrophobic poly(propylene glycol) (PPG) blocks were synthesized via the controlled cationic‐induced living polymerization of a phosphoranimine (Cl₃P?NSiMe₃) at ambient temperature. A PPG block can function as either a classical hydrophobic block or a less hydrophobic component by varying the nature of a phosphazene block. The aqueous phase behavior of MEEP‐PPG‐MEEP block copolymers was investigated using fluorescence techniques, TEM, and dynamic light scattering (DLS). The critical micelle concentrations (cmcs) of MEEP‐PPG‐MEEP block copolymers were determined to be in the range of 3.7–16.8 mg/L. The mean diameters of MEEP‐PPG‐MEEP polymeric micelles, measured by DLS, were between 31 and 44 nm. The equilibrium constants of pyrene in these micelles ranged from 4.7 × 10⁴ to 9.6 × 10⁴. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 692–699, 2009     

Effect of CO2 exposure on free volumes in polystyrene studied by positron annihilation spectroscopy

Free‐volume properties, size and distribution, in amorphous polystyrene exposed to CO₂ gases have been measured as a function of pressure to 800 psi (5.5 MPa), of time, and of temperature using positron annihilation lifetime spectroscopy. The free volume increases significantly and its distribution broadens as a function of pressure. The free volume relaxes as a function of time with a characteristic time of 15 h, and 5.7 h for 400, and 800 psi, respectively, after depressurizing under vacuum. A portion of free volume created by CO₂ exposure remains permanently in the polymer after CO₂ exposure. The glass transition temperature decreases significantly as a function of CO₂ pressure from the free‐volume data and is compared with the differential scanning calorimeter results. The observed free‐volume variations as a function of pressure, time, and temperature are discussed in terms of hole expansion, creation, free‐volume relaxation, plasticization, and hole filling in amorphous polymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 388–405, 2008     

Synthesis and characterization of block poly(ester‐ether‐urethane)s from bacterial poly(3‐hydroxybutyrate) oligomers

Telechelic hydroxylated poly(3‐hydroxybutyrate) (PHB‐diol) oligomers have been successfully synthesized in 90–95% yield from high molar mass PHB by tin‐catalyzed alcoholysis with different diols (mainly 1,4‐butanediol) in diglyme. The PHB‐diol oligomers structure was studied by nuclear magnetic resonance, Fourier transformed infrared spectroscopy MALDI‐ToF MS, and size exclusion chromatography, whereas their crystalline structures, thermal properties and thermal stability were analyzed by wide angle X‐ray scattering, DSC, and thermogravimetric analyses. The kinetic of the alcoholysis was studied and the influence of (i) the catalyst amount, (ii) the diol amount, (iii) the reaction temperature, and (iv) the diol chain length on the molar mass was discussed. The influence of the PHB‐diol molar mass on the thermal stability, the thermal properties and optical properties was investigated. Then, tin‐catalyzed poly(ester‐ether‐urethane)s (PEEU) of M_n = 15,000–20,000 g/mol were synthesized in 1,2‐dichloroethane from PHB‐diol oligomers (P_ester) with modified 4,4'‐MDI and different polyether‐diols (P_ether) (PEG‐2000, PEG‐4000, and PPG‐PEG‐PPG). The influence of the PHB‐diol chain length, the P_ether/P_ester ratio, the polyether segment nature and the PEG chain length on the thermal properties and crystalline structures of PEEUs was particularly discussed. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1949–1961     

Effect of soft segment component on moisture‐permeable polyurethane films

The effect of soft segment component and molecular weight combination on moisture‐permeable polyurethane films was studied. Moreover, water sorption phenomenon in films was observed with infrared analysis. As for soft segment components, PTMG/PEG and PTMG/PPG were used and molecular weight combinations were changed. Different tendency appeared in the experimental results corresponding to PEG system and PPG system. Moisture permeability P in PEG system increased with increasing PEG content, but P changed little in the case of PPG system. Both hydrogen‐bonded concentration by infrared measurement and the higher order term Δh of Mooney–Rivlin plot by stress–strain relationships indicate the existence of aggregate structure of hard segment. It is considered that ether group in PEG is more active than that in PPG. Therefore, small size of aggregate structure indicated as Δh appears in PEG system owing to inhibition of aggregate structure growth. Whereas, ether group in PPG system does not inhibit hydrogen bond in urethane group and large size of aggregate structure appears. From water affinity relationship analysis, hydrophilicity of samples with PTMG/PEG = 2000/2000 increased with increasing PEG content. Consequently, it is suggested that not only size but also hydrogen‐bonded concentration of urethane group in aggregate structure affects moisture permeability. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 573–583, 2006     

Vibrational spectroscopy analysis of ion conduction mechanism in dispersed phase polymer nanocomposites

A novel combination of dispersed phase polymer nanocomposite electrolyte based on PEO₈‐LiClO₄+ x wt % nano‐CeO₂ has been investigated. A model for ion transport mechanism has been proposed to account for substantial enhancement of its electrical conductivity by ～ 2 orders of magnitude at low volume fraction of the filler reinforcement in the polymer nanocomposite films. The strength of the proposed model is based on unambiguous evidences from FTIR, TEM, and conductivity analysis. The FTIR results provide clear role of nanofiller concentration on ion–ion interaction quantified in terms of the fraction of free anion and ion‐pairs present in the nanocomposite films and its excellent correlation with conductivity versus filler concentration. The presence of asymmetry in the ν₄(ClO₄^?) band observed at 625 cm^?1 is attributed to its resolved degeneracy suggesting the presence of both uncoordinated and cation‐coordinated ClO₄^? anion in the matrix due to ion–ion and ion–filler interactions assisted by Lewis acid–base interaction. The enhancement in conductivity at low concentration is possibly due to direct interaction of nano‐CeO₂ with both polymer host and anions resulting in the release of ionic charges. Drastic conductivity reduction at higher concentration is related to charge immobilization because of ion/ion‐pair entrapment by local clusters of filler as evidenced in TEM. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 60–71, 2009     

Novel amphiphilic triblocks fitted with photocrosslinkable termini,and their photocrosslinking to conetworks

Two new telechelic amphiphilic triblock copolymers, HE₃‐PEG‐b‐PDMS‐b‐PEG‐HE₃ and HE₃‐PEG‐b‐PDMS‐b‐PEG‐HE₃, i.e., sequence‐reversed triblocks of hydrophilic poly(ethylene glycol) (PEG) and hydrophobic polydimethylsiloxane (PDMS) segments fitted with photocrosslinkable tri[2‐(3,4‐cyclohexane oxide)ethyl‐dimethylsiloxy]silane (HE₃) termini, were synthesized, characterized, photocrosslinked to amphiphilic conetworks (APCNs), and the properties of the APCNs were analyzed. APCNs in which the crosslinking sites are located in the hydrophobic domains exhibited significantly better mechanical properties than those in which the crosslinks were in the hydrophilic domains. The stiff domains formed of the UV‐crosslinkable HE₃ chain‐end substituents provide not only crosslinking but reinforcement as well. The crosslinking/reinforcement efficiency was greatly enhanced by the addition of excess HE₃. Water‐swollen APCNs were optically clear and exhibited mechanical properties appropriate for biomedical application. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 174–185, 2008     

H‐shaped (ABCDE type) quintopolymer via click reaction [3 + 2] strategy

H‐shaped quintopolymer containing different five blocks: poly(ε‐caprolactone) (PCL), polystyrene (PS), poly(ethylene glycol) (PEG), and poly(methyl methacrylate) (PMMA) as side chains and poly(tert‐butyl acrylate) (PtBA) as a main chain was simply prepared from a click reaction between azide end‐functionalized PCL‐PS‐PtBA 3‐miktoarm star terpolymer and PEG–PMMA‐block copolymer with alkyne at the junction point, using Cu(I)/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as a catalyst in DMF at room temperature for 20 h. The H‐shaped quintopolymer was obtained with a number–average molecular weight (M_n) around 32,000 and low polydispersity index (M_w/M_n) 1.20 as determined by GPC analysis in THF using PS standards. The click reaction efficiency was calculated to have 60% from ¹H NMR spectroscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4459–4468, 2008     

Synthesis,characterization, and nucleotidic chain cleavage ability of uncharged water soluble poly(ethylene glycol)‐fullerene derivatives with an amphiphilic character

Water‐soluble fullerenes containing two poly(ethylene glycol) branches [Full‐(PEG)₂] were prepared starting from commercial poly(ethylene glycol)‐monomethyl ethers and C₆₀ [Full‐(PEG)₂]s chemical characterization was made by FT‐IR, NMR, and MALDI‐TOF mass spectrometric analyses. Their thermal stability was determined by TGA experiments. The capability of C₆₀‐derivatives to induce oligonucleotide cleavage under visible light irradiation was also ascertained. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2154–2153, 2008     

Synthesis and hydrolytic stability of poly(oxyethylene‐H‐phosphonate)s

Poly(oxyethylene‐H‐phosphonate)s (POE‐H‐Ps), with different poly(oxyethylene) segment lengths, were synthesized via conventional two‐stage polycondensation reaction of dimethyl‐H‐phosphonate and poly(ethylene glycols) (PEGs), with nominal molecular weights of 400, 600, and 1000 Da. The changes in the composition of the reaction mixtures during the polycondensation process were followed by size‐exclusion chromatography (SEC) and NMR. It was found that the three PEG fragments yield reproducibly POE‐H‐Ps with the following molecular weights: ～3000 Da (PEG‐400), ～6000 Da (PEG‐600), and ～10,000 Da (PEG‐1000) as measured by SEC, NMR, and VPO. The hydrolytic behavior of POE‐H‐Ps upon storage and in aqueous media with pH 3, 7.4, and 8 was studied for the first time by a combination of NMR and SEC. It was found that the long‐term stability of the polymers in dry state depends on the length of the PEG fragments and decreased in the following order: POE‐H‐P_(PEG‐1000) > POE‐H‐P_(PEG‐600) > POE‐H‐P_(PEG‐400). The hydrolytic transformation of the polymers in aqueous media is affected mostly by the pH of the solution. The degradation products are PEG fragments containing phosphonate end groups—an important prerequisite for the usage of the POE‐H‐Ps as nontoxic drug delivery vehicles and in vivo precursors for PEGylated prodrugs. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4130–4139, 2008     

Packing manner of graft copolymers with rigid‐rod main chains and amorphous‐crystalline diblock copolymers as side chains

We have investigated the morphology and packing manner of graft copolymers consisting of rigid‐rod‐like poly(γ‐benzyl L ‐glutamate) (PBLG) main chains and grafted diblock copolymers of amorphous poly(propylene glycol) (PPG) and crystalline poly(ethylene glycol) (PEG). The results of differential scanning calorimetry and wide‐angle X‐ray scattering measurements for graft copolymers with higher side‐chain volume fractions suggest that the rodlike main chains and crystallized PEG chains exist in segregated domains. Small‐angle X‐ray scattering profiles for these samples show diffraction intensity maxima accompanied by higher order peaks, the positions of which suggest the formation of an ordered layered structure. From these observations, the graft copolymers are estimated to form repeated layered structure consisting of segregated PBLG, PPG, and PEG layers. A proposed model for molecular packing of the graft copolymers is consistent with the experimental observation that the repeating distance for the layered structure decreases with an increase in the volume fraction of side chains. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1904–1912, 2002     

Volume dependence of thermal conductivity and bulk modulus for poly(propylene glycol)

The thermal conductivity λ and heat capacity per unit volume of poly(propylene glycol) PPG (0.4 and 4.0 kg·mol⁻¹ in number-average molecular weight) have been measured in the temperature range 150–295 K at pressures up to 2 GPa using the transient hot-wire method. At 295 K and atmospheric pressure, λ = 0.147 W m⁻¹K⁻¹ for PPG (0.4 kg·mol⁻¹) and λ = 0.151 W m⁻¹K⁻¹ for PPG (4.0 kg·mol⁻¹). The temperature dependence of λ is less than 4 × 10⁻⁴ W m⁻¹K⁻² for both molecular weights. The bulk modulus has been measured in the temperature range 215–295 K up to 1.1 GPa. At atmospheric pressure, the room temperature bulk moduli are 1.97 GPa for PPG (0.4 kg·mol⁻¹) and 1.75 GPa for PPG (4.0 kg·mol⁻¹). These data were used to calculate the volume dependence of $ \lambda ,g\, = - \left( {\frac{{\partial \lambda /\lambda }}{{\partial V/V}}} \right)_T $. At room temperature and atmospheric pressure (liquid phase) we find g = 2.79 for PPG (0.4 kg·mol⁻¹) and g = 2.15 for PPG (4.0 kg·mol⁻¹). The volume dependence of g, (∂g/∂ log V)_T varies between −19 to −10 for both molecular weights. Under isochoric conditions, g is nearly independent of temperature. The difference in g between the glassy state and liquid phase is small and just outside the inaccuracy of g of about 8%. The theoretical model for λ by Horrocks and McLaughlin yields an overestimate of g by up to 120%. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 345–355, 1998     

A study on free volume of acrylonitrile‐styrene copolymer and methyl methacrylate‐styrene copolymer by using positron annihilation

The o‐Ps lifetime τ₃ and the intensity I₃ of ST‐AN copolymers and ST‐MMA copolymers have been determined by using the positron annihilation technique. The average free volume hole radius R is estimated according to Tao's and Eldrup's model. The result shows that the average free volume hole size mainly attributes to lateral group volume and polarity of macromolecular chain as well as polymerizing temperature, and the o‐Ps intensity I₃ to the effect of the lateral group volume and the polarity. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 465–472, 1999     

One‐pot synthesis of star‐block copolymers using double click reactions

3‐Arm star‐block copolymers, (polystyrene‐b‐poly(methyl methacrylate))₃, (PS‐b‐PMMA)₃, and (polystyrene‐b‐poly(ethylene glycol))₃, (PS‐b‐PEG)₃, are prepared using double‐click reactions: Huisgen and Diels–Alder, with a one‐pot technique. PS and PMMA blocks with α‐anthracene‐ω‐azide‐ and α‐maleimide‐end‐groups, respectively, are achieved using suitable initiators in ATRP of styrene and MMA, respectively. However, PEG obtained from a commercial source is reacted with 3‐acetyl‐N‐(2‐hydroxyethyl)‐7‐oxabicyclo[2.2.1]hept‐5‐ene‐2‐carboxamide (7) to give furan‐protected maleimide‐end‐functionalized PEG. Finally, PS/PMMA and PS/PEG blocks are linked efficiently with trialkyne functional linking agent 1,1,1‐tris[4‐(2‐propynyloxy)phenyl]‐ethane 2 in the presence of CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) at 120 °C for 48 h to give two samples of 3‐arm star‐block copolymers. The results of the peak splitting using a Gaussian deconvolution of the obtained GPC traces for (PS‐b‐PMMA)₃ and (PS‐b‐PEG)₃ displayed that the yields of target 3‐arm star‐block copolymers were found to be 88 and 82%, respectively. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7091–7100, 2008     

Irreversible temperature‐responsive formation of high‐strength hydrogel from an enantiomeric mixture of starburst triblock copolymers consisting of 8‐arm PEG and PLLA or PDLA

Starburst triblock copolymers consisting of 8‐arm poly(ethylene glycol) (8‐arm PEG) and biodegradable poly(L ‐lactide) (PLLA) or its enantiomer poly(D ‐lactide) (PDLA), 8‐arm PEG‐b‐PLLA‐b‐PEG ( Stri‐L ), and 8‐arm PEG‐b‐PDLA‐b‐PEG ( Stri‐D ) were synthesized. An aqueous solution of a 1:1 mixture ( Stri‐Mix ) of Stri‐L and Stri‐D assumed a sol state at room temperature, but instantaneously formed a physically crosslinked hydrogel in response to increasing temperature. The resulting hydrogel exhibited a high‐storage modulus (9.8 kPa) at 37 °C. Interestingly, once formed at the transition temperature, the hydrogel was stable even after cooling below the transition temperature. The hydrogel formation process was irreversible because of the formation of stable stereocomplexes. In aqueous solution, gradual hydrolytic erosion was observed because of degradation of the hydrogel. The combination of rapid temperature‐triggered irreversible hydrogel formation, high‐mechanical strength, and degradation behavior render this polymer mixture system suitable for use in injectable biomedical materials, for example, as a drug delivery system for bioactive reagents or a biodegradable scaffold for tissue engineering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6317–6332, 2008     

Y‐shaped poly(ethylene glycol) and poly(trimethylene carbonate) amphiphilic copolymer: Synthesis and for drug delivery

New Y‐shaped (AB₂‐type) amphiphilic copolymers of poly(ethylene glycol) (PEG) with poly(trimethylene carbonate) (PTMC), PEG‐b‐(PTMC)₂, were successfully synthesized by the ring‐opening polymerization (ROP) of TMC with bishydroxy‐modified monomethoxy‐PEG (mPEG). First, a bishydroxy functional ROP initiator was synthesized by esterification of acryloyl bromide with mPEG, followed by Michael addition using excess diethanolamine. A series of Y‐shaped amphiphilic PEG‐(PTMC)₂ block copolymers were obtained via ROP of TMC using this PEG with bishydroxyl end groups as macroinitiator and ZnEt₂ as catalyst. The amphiphilic block copolymers with different compositions were characterized by gel permeation chromatography (GPC) and ¹H NMR, and their molecular weight was measured by GPC. The results showed that the molecular weight of Y‐shaped copolymers increased with the increase of the molar ratio of TMC to mPEG‐(OH)₂ initiator in feed while the PEG chain length was kept constant. The Y‐shaped copolymer mPEG‐(PTMC)₂ could self‐assemble into micelles in aqueous medium and the critical micelle concentration values of the micelles decrease with increase in hydrophobic PTMC block length of mPEG‐(PTMC)₂. The in vitro cytotoxicity and controlled drug release properties of the Y‐shaped amphiphilic block copolymers were also investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8131–8140, 2008     

An H‐shaped polymer bonding β‐cyclodextrin at branch points: Synthesis and influences of attached β‐cyclodextrins on physical properties

We report on the synthesis of an H‐shaped polymer bonding β‐cyclodextrin (β‐CD) at branch points and influences of attached β‐CD on physical properties. First, a poly(ethylene glycol)(PEG)‐based functional macroinitiator bearing two azidos and four chlorines at chain‐ends (PEG‐2N₃(‐4Cl)) was prepared via terminal modification reactions. Then, PEG‐2N₃(‐4Cl) was applied to initiate the atom transfer radical polymerization of N‐isopropylacrylamide, leading to the synthesis of an H‐shaped block polymer with PEG as the central chain and poly(N‐isopropylacrylamide) (PNIPAM) as side‐arms (PEG‐2N₃(‐4PNIPAM)). Azido groups were at the branch points of the polymer. Finally, the click reaction between PEG‐2N₃(‐4PNIPAM) and alkynyl monosubstituted β‐cyclodextrin (β‐CD) afforded another H‐shaped polymer with two β‐CDs bonding at the polymer branch points (PEG‐2CD(‐4PNIPAM)). The glass transition temperature (T_g) and lower critical solution temperature (LCST) of the H‐shaped polymer increased after the attachment of β‐CD. The self‐assembly and thermal responsive behaviors, as well as the encapsulation behaviors of PEG‐2CD(‐4PNIPAM) were also altered. When temperature was below the LCSTs, PEG‐2N₃(‐2PNIPAM) dissolved in water molecularly, whereas PEG‐2CD(‐4PNIPAM) could self‐assemble into nano‐sized micelles. After the LCST transitions, PEG‐2N₃(‐4PNIPAM) aggregated into micron‐sized unstable particles, whereas PEG‐2CD(‐4PNIPAM) transformed into PNIPAM‐cored nanomicelles. Besides, PEG‐2CD(‐4PNIPAM) can encapsulate doxorubicin below its LCST due to the formation of micelles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Preparation,structure, and property of polyoxymethylene/carbon nanotubes thermal conducive composites

Polyoxymethylene (POM)/multiwalled carbon nanotubes (MWNTs) nanocomposites were prepared through a simple solution‐evaporation method assisted by ultrasonic irradiation. To enhance the dispersion of MWNTs in POM, MWNTs were chemically functionalized with PEG‐substituted amine (MWNT‐g‐PEG), which exhibited strong affinity with POM due to their similar molecular structure. The thermal conductivity and the mechanical properties of the composites were investigated, which showed that the thermal conductive properties of POM were improved remarkably in the presence of MWNTs, whereas reduced by using MWNT‐g‐PEG due to the heat transport barrier of the grafted‐PEG‐substituted amine chain. A nonlinear increase of the thermal conductivity was observed with increasing MWNTs content, and the Maxwell‐Eucken model and the Agari model were used for theoretical evaluation. The relatively high effective length factor of the composite predicted with mixture equation indicated that there were few entangles of MWNTs for the samples of MWNT‐g‐PEG in the composites. The mechanical strength of the composites can be improved remarkably by using suitable content of such functionalized MWNTs, and with the increase of the aliphatic chain length of PEG‐substituted amine, the toughness of the composites can be enhanced. Transmission electron microscope result indicated that MWNT‐g‐PEG exhibited strong affinity with POM and a good dispersion of MWNTs was achieved in POM matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 905–912, 2010     

Highly soluble green‐emitting Ir(III) complexes with 9‐(6‐phenyl‐pyridin‐3‐ylmethyl)‐9H‐carbazole ligands and their application to polymer light‐emitting diodes

Highly organic soluble Ir(III) complexes with 9‐(6‐phenyl‐pyridin‐3‐ylmethyl)‐9H‐carbazole were simply synthesized, and the solubility of the new complex was significantly improved when compared with the conventional green‐emitting Ir(ppy)₃. Since a carbazole group is tethered through a nonconjugated methylene spacer, the photophysical properties of new complexes are almost identical with those of conventional Ir(ppy)₃. The pure complexes were utilized to prepare electrophosphorescent polymer light‐emitting diodes (PLEDs). The device performances were observed to be relatively better or comparable with those of Ir(ppy)₃ based poly(N‐vinylcarbazole) systems. The integration of rigid hole‐transporting carbazole and phosphorescent complex provides a new route to design highly efficient solution‐processable complex for electrophosphorescent PLED applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7419–7428, 2008     

Effect of ammonia on the temperature‐dependent conductivity and thermopower of polypyrrole

We report the first measurements of the effect of ammonia gas on the temperature dependence of the conductivity and thermoelectric power of polypyrrole films. Our data are for samples of very different conductivities, extending down to a temperature of 200 K for low‐conductivity polypyrrole gas sensors, and down to 4.2 K for more highly‐conducting PPy(PF₆) samples. We demonstrate that (except for the most metallic case) our polypyrrole samples show greater sensitivity to ammonia as the temperature is lowered (i.e. the fractional reduction in conductivity is greater at lower temperatures). Remanent decreases in conductivity are present after the removal of ammonia for higher pressure exposures, and remanent increases in the metal‐like thermoelectric power for the PPy(PF₆) for samples grown at higher temperatures. Our results indicate that the mechanism of this conductivity decrease in PPy(PF₆) is that ammonia causes a reduction in the size of metallic regions as disordered barrier regions are thickened. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1331–1338, 2006