Kinetic spectrophotometric method for the determination of urinary cobalt based on its catalytic effect on the oxidation of -adrenaline hydrochloride by hydrogen peroxide

A catalytic for determination of nanomolar concentrations of Co(II), i.e., oxidation of -adrenaline hydrochloride with H₂O² in alkaline medium, is proposed. The reaction gives a low limit of detection of 2.5 × 10 ⁻⁹ M Co(II) in the reaction mixture, good reproducibility with a relative standard deviation (R.S.D.) of 4−5% in the Co(II) concentration range 8.0 × 10⁻⁹−8.0 × 10⁻⁸M and good selectivity. On the basis of this indicator reaction, a catalytic-spectrophotometric method for the determination of cobalt in small urine samples (5.00 ml) was elaborated. The analysis of 17 urine samples, taken from healthy persons of different ages, gave cobalt concentrations in the range 0.20–1.50 μmol 1⁻¹. The R.S.D. for ten replicate analyses of a urine sample with an average cobalt content of 0.63 μmol 1⁻¹ was 5.6%. The reliability of the method was verified by a comparative photometric method (r = 0.9755) and by a determination based on known additions of cobalt (r = 0.9894).     

Kinetic spectrophotometric determination of hydrazine

A sensitive kinetic method for determining low levels of hydrazine has been described. The method is based on the measurement of the rate of the reaction between hydrazine and Mo(VI) in the presence of hydrochloric acid. The redox reaction was monitored spectrophotometrically at 710 nm. The variable-time and fixed-time methods were used. The calibration graph was linear for hydrazine concentrations of 1.0 × 10⁻⁴-1.4 × 10⁻² M, using the fixed-time method of analysis. The method is simple, rapid, precise, sensitive and widely applicable.     

靛蓝胭脂红-溴酸钾体系催化光度法测定微量碘

研究了在室温及0．4mol/L H2SO4介质中碘离子对KBrO3氧化靛蓝胭脂红褪色反应的催化作用,建立了一种测定微量碘的新方法。碘离子浓度在0．20－2．0μg/mL范围内与△A呈线性关系,检测限为0．14μg/mL。多数常见离子无干扰。可用于海带中微量碘的测定。     

酶催化动力学光度法测定H2O2

H2O2能够氧化偶氮染料刚果红使之褪色,而模拟酶—血红蛋白对其具有催化作用。据此建立了一种以刚果红为指示剂的H2O2-刚果红-血红蛋白酶催化反应体系测定痕量H2O2的新方法。确定了反应的最佳条件,体系的酸度为pH10.7的NH3-NH4Cl缓冲溶液,最大吸收波长为497 nm。该法的线性范围为8.0×10^-8-8.0×10^-5mol/L,检出限为1.97×10^-9mol/L,表观摩尔吸光系数为4.6×10^4L.mol-1.cm^-1。该方法可用于雨水及消毒水中H2O2的测定。     

动力学光度法测定痕量甲醛

在稀硫酸溶液中,甲醛对KClO3氧化罗丹明6G褪色反应有催化作用,研究了其动力学条件,建立了测定痕量甲醛的动力学光度分析方法,线性范围为0.02～1.8μg/mL,检出限为1.5×10-8g/mL。该法用于湖水、饮料和漆料中痕量甲醛的测定,标准加入回收率为93.8%～108.5%,RSD为2.6%～3.4%。     

Effect of preparation methods on Pt/alumina catalysts for the hydrogen iodide catalytic decomposition

Three kinds of Pt/alumina catalysts were prepared by impregnation-hydrogen reduction,impregnation-hydrazine reduction and electroless plating methods.Their differences in the structures,specific areas and particle sizes were characterized by XRD,BET and TEM,respectively.Furthermore,their catalytic activities for the hydrogen iodide(HI)decomposition were evaluated in a fixed bed reactor.The results show that the catalyst 5%Pt/Al_2O_3 prepared by the electroless plating has the optimum catalytic properties...     

氧化酸性铬蓝K褪色动力学光度法测定微量芦丁

基于2 mmol/L的H2SO4介质中,微量芦丁催化H2O2氧化酸性铬蓝K(ACBK)的褪色反应,建立了测定微量芦丁的动力学光度法。方法的检出限为1.08μg/L,线性范围为3.6~400μg/L。实验讨论了酸度、反应物浓度、温度、反应时间、干扰离子等因素的影响,确定了该体系反应的最佳条件,并测定了一些动力学参数,催化反应的表观活化能为73.22 kJ/mol。在25 mL溶液中,测定10.0μg芦丁的相对标准偏差为1.6%(n=11)。方法用于测定槐米和芦丁片剂中的芦丁,相对标准偏差为1.0%~1.1%,标准加入回收率为98.0%~101.7%。     

Kinetic method for determination of nanogram amounts of copper(II) by its catalytic effect on hexacynoferrate(III)-citric acid indicator reaction

This paper describes a highly sensitive, selective catalytic-kinetic-spectrophotometric method for the determination of copper(II) concentration as low as 6 ng ml⁻¹. The method is based on the catalytic effect of copper(II) on the oxidation of citric acid by alkaline hexacyanoferrate(III). The reaction was followed by measuring the decrease in absorbance of hexacyanoferrate(III) at 420 nm (λ_max of [Fe(CN)₆]³⁻, ∈ = 1020 dm³ mol⁻¹ cm⁻¹). The dependence of rate of the indicator reaction on the reaction variables has been studied and discussed to propose a suitable mechanism to get a relation between the reaction rate and [Cu²⁺]. A fixed time procedure has been used to obtain a linear calibration curve between the initial rate and lower [Cu²⁺] or log[Cu²⁺] in the range 1 × 10⁻⁷ to 4 × 10⁻⁴ mol l⁻¹ (6.35-25,400 ng ml⁻¹). The detection limit has been calculated to be 4 ng ml⁻¹. The maximum average error is 3.5%. The effect of the presence of various cations, commonly associated with copper(II) and some anions has also been investigated and discussed. The proposed method is sensitive, accurate, rapid and inexpensive compared to other techniques available for determination of copper(II) in such a large range of concentration. The new method has been successfully applied for the determination of copper(II) in various samples.     

Kinetic and maximum-absorbance spectrophotometric methods for the determination of olanzapine

Two simple and sensitive spectrophotometric methods were developed for the determination of olanzapine (OLZ) based on its oxidation with potassium iodate in a sulfuric acid medium to produce an intense violet-colored species exhibiting a maximum absorbance at 537 nm. The initial rate of formation and the maximum absorbance of the violet-colored oxidized product were monitored, in the first and second methods. The various experimental parameters affecting the rate of development and stability of the oxidized product were carefully studied and optimized. Beer’s law was obeyed up to 4.0 and 7.0 μg cm⁻³ OLZ with correlation coefficients of 0.998 and 0.996 (n = 6) and detection limits of 0.1 and 0.15 μg cm⁻³, for the initial rate and maximum absorbance methods. The proposed methods were conveniently applied to the determination of OLZ in its dosage forms and in spiked serum samples. Correspondence: Ashraf A. Mohamed, Department of Chemistry, Faculty of Science, King Faisal University, P.O. Box 1759, Al-Hassa-31982, Saudi Arabia.     

催化动力学光度法测定铬的研究

在稀HCl介质中,微量铬(Ⅲ)对K2S2O8氧化酸性大红GR的褪色反应有明显的催化作用。据此建立了催化动力学光度法测定微量铬(Ⅲ)的新方法。确定了反应的最佳条件,并讨论了动力学参数。方法线性范围为0.008~0.4mg/L,检出限为2.96×10-6g/L。方法已用于自来水、钢厂废水、污水中微量铬(Ⅲ)的测定。     

过氧化氢氧化灿烂甲酚蓝动力学光度法测定痕量铝

基于pH3.6的乙酸 乙酸钠缓冲介质中Al3 对过氧化氢氧化灿烂甲酚蓝(BCB)褪色反应的催化作用,提出了测定痕量铝的新的催化动力学光度法。研究了该法的适宜反应条件,方法的线性范围为0～100ng mL,检出限为0.9ng mL。方法已用于样品中痕量铝的测定。     

Kinetic–catalytic–spectrophotometric determination of low concentrations of molybdenum in white wines

The paper describes the determination of the molybdenum content in white wines based on its catalytical action on the kalium iodide oxidation by hydrogen peroxide in acid medium.

The optimum reaction conditions (the catalyst, KI and H₂O₂ concentrations, the pH value, the order of the reagent additions, the temperature) have been found by studying the effect of the reaction variables.

The influence of some metallic ions (Ca²⁺, Mg²⁺, Zn²⁺, Cd²⁺, Fe²⁺ and Fe³⁺) and complexing anions (F⁻, C₂O²⁻₄, EDTA⁴⁻) on the catalyzed reaction rate was elucidated.

The molybdenum concentration was estimated by the tangent, fixed-time and fixed-absorbance method. The obtained average values for molybdenum content in white wines are within the 1.77×10⁻⁷–1.83×10⁻⁷ mol l⁻¹ range.     

煌焦油蓝-溴酸钠体系催化动力学光度法测定痕量甲醛

基于H2SO4介质中甲醛催化NaBrO3氧化煌焦油蓝的褪色反应,建立了测定痕量甲醛的催化动力学分析方法。探讨了该方法的反应机理,对其反应条件进行了研究。测定线性范围为0．16～2．00μg／mL,检出限为8ng／mL。方法已应用于海产品水发液中痕量甲醛的测定。     

Kinetic spectrophotometric determination of amodiaquine and chloroquine

Abstract  Two simple, sensitive, and selective spectrophotometric methods were developed for determining amodiaquine (AQ) and chloroquine (CQ) based on their oxidation with potassium iodate and potassium bromate, respectively. The initial rates of oxidation of AQ and CQ were monitored at 342 and 343 nm, the wavelengths of maximum absorptions of the two drugs. The various experimental parameters affecting oxidation reactions were thoroughly studied and optimized. Beer’s law was obeyed for 0.2–4.0 and 0.5–5.0 μg cm⁻³, with correlation coefficients of 0.9999 and 0.9998 (n = 6) and a detection limit (based on the 3S _b -criterion) of 0.04 and 0.06 μg cm⁻³ for AQ and CQ. The proposed methods were conveniently applied to determining AQ and CQ in pure and dosage forms. Graphical abstract        

Kinetic catalytic determination of trace levels of iodide based on the oxidation of basic dyes with hydrogen peroxide monitored potentiometrically using simple PVC electrodes

Four sensitive catalytic potentiometric methods have been developed for trace levels determination of iodide based on its catalytic effects on the oxidation of four dyes: viz. variamine blue (VB), rhodamine B (RB), methylene blue (MB) and malachite green (MG), with H₂O₂ in H₃PO₄ medium at 25 ± 0.5 °C. The catalyzed reaction rates were estimated potentiometrically by monitoring the potential of the corresponding dye-PVC ion selective electrodes. To select the optimized reaction conditions offering the highest sensitivity of the method, parallel studies were carried out on each dye catalyzed reaction including: the effect of reactant concentration, reaction medium and temperature. The working calibration curves were linear over the concentration range from 0.32 to 2.54 mg L⁻¹ iodide for VB method and from 3.2 to 12.7 mg L⁻¹ for other ones. The tolerance limits of more than 20 interfering species were listed indicating the high selectivity of the method. Trace iodide in edible salt and pharmaceutical samples was determined without the need for separation or preconcentration procedures.     

Kinetic spectrophotometric determination of Tween 80

A novel kinetic spectrophotometic method for the determination of Tween 80 based on its interaction with 5(p-dimethylaminobenzylidene)rhodanine (PDR) in alkaline media is reported. The effect of variable on the rate of interaction of Tween 80 and PDR was investigated in order to establish the optimum conditions. The interaction was monitored spectrophotometically and change in absorbance (ΔA) of PDR at 464 nm at times of 30 and 270 s was used as an analytical parameter. Tween 80 can be measured in the range of 2.5×10⁻⁵ to 1.25×10⁻³ M with detection limit of 1.5×10⁻⁵ M. The relative standard deviation for eight replicate determinations of 2×10⁻⁴ and 1×10⁻³ M of Tween 80 solution was 4.08 and 3.88%, respectively. This method was used to determine Tween 80 in biscuit and multivitamin syrup.     

Kinetic spectrophotometric determination of bromide in clidinium-c drug

A simple,rapid and sensitive method has been described for the determination of the trace amounts of bromide.The method is based on the catalytic effect of bromide ion on the oxidation of methylene blue by bromate in sulfuric acid media.The reaction is monitored spectrophotometrically by measuring the decrease in the absorbance of methylene blue at 665 nm. Bromide was determined in the range of 0.05-1.90μg/mL with the detection limit of 0.03μg/mL.The relative standard deviations of five replicate determinations of 0.20 and 10.0μg/mL of bromide were 2.4%and 1.8%,respectively.The influence of potential interfering ions and substances was studied.The method is applied to the analysis of bromide in clidinium-c tablet as a real sample.     

Kinetic spectrophotometric method for rapid determination of trace formaldehyde in foods

A simple and sensitive kinetic-spectrophotometric method was developed for the determination of ultra trace amount of formaldehyde in food samples. The method was based on the oxidation of rhodamine B (RhB) by potassium bromate in sulfuric acid medium (formaldehyde as catalyst). The reaction was monitored by measuring the decrease in absorbance of the dye at 515 nm after 6 min. The developed method allowed the determination of formaldehyde in the range of 10–100 μg L⁻¹ with good precision, accuracy and the detection limit was down to 2.90 μg L⁻¹. The relative standard deviations for the determination of 10 and 60 μg L⁻¹ of formaldehyde were 3.0% and 1.9% (n = 10), respectively. The method was found to be sensitive, selective and was applied to the determination of formaldehyde in foods with satisfactory results.     

催化动力学光度法测定超痕量银的研究

催化动力学光度法测定超痕量银的研究张志琪，陈世荣，陈党教，张根绪（陕西师范大学化学系，西安，７１００６２）关键词银，罗丹明Ｂ，催化褪色反应，动力学分析法，催化光度法在催化动力学分析法研究领域，新的高灵敏度的指示反应的研究具有重要的现实意义［１］。前文...