Mössbauer effect study of the pseudo-binary system (Ti1−x Nb x )Fe2

Mössbauer spectroscopy and X-ray diffraction measurements have been done on (Ti_1–x Nb _x )Fe₂ compounds in order to investigate the effect of Nb on the magnetic properties of TiFe₂. The experimental results show that Nb enters the lattice by filling Ti sites, thereby forming a continuous phase over the whole range of Nb concentrations. The Mössbauer spectra at 80 K fitted with a magnetic hyperfine field distribution show a continuous decrease of the average magnetic hyperfine field with increasing Nb concentration, as well as several different magnetic configurations forx0.3.     

Properties of Fe–Ga based powders prepared by mechanical alloying

Alloys of Fe–Ga with starting compositions of 17, 19, 21, 23, and 25 at% Ga and Fe₈₁Ga₁₇Z₂ (Z=Si, Sn) have been prepared by mechanical alloying. Samples were milled in a SPEX Model 8000 mill with a ball to sample weight ratio of about 4:1. Phase formation as a function of milling time has been investigated for the 19 at% Ga sample and suggests that milling times of 12 h produce fully alloyed samples. Alloys have been studied by electron microprobe, X-ray diffraction, vibrating sample magnetometery and ⁵⁷Fe Mössbauer effect spectroscopy. Fully milled powders have measured compositions of Fe_100−xGa_x with x=15.7, 17.0, 19.0, 22.4, and 24.0 and Fe_83.1Ga_15.2Z_1.7 (for both Z=Si and Sn). X-ray diffraction showed the presence of a disordered bcc phase with no indication of an ordered D0₃ phase. However, the latter is difficult to observe with X-ray diffraction because of the low intensity of the fcc superlattice peaks. A bimodal Fe hyperfine field distribution as obtained from Mössbauer effect spectra indicated the presence of two discrete Fe environments. The results suggested a lower degree of Ga clustering than has been previously observed in Fe–Ga alloys, of similar composition, prepared by melt spinning. The microstructure is similar to that of Fe–Ga thin films prepared by combinatorial sputtering. Some samples have also been studied after annealing at 800 °C for 8 h. No changes were observed in X-ray diffraction patterns after annealing. However, Mössbauer effect studies show the formation of D0₃ and L1₂ order in annealed samples analogous to the phases observed in melt spun ribbons of similar composition.     

Thermal stability of Fe3Si-based nanocrystals

We studied the thermal stability of nanocrystalline (Fe₃Si)_0.95Nb_0.05 and Fe₃Si alloys prepared by high-energy ball milling. Alloys were characterized by Mössbauer spectrometry, as well as X-ray diffractometry and transmission electron microscopy. The Nb-containing alloy was considerably more stable against grain growth than was the binary Fe₃Si alloy. Mössbauer spectrometry showed that the Nb atoms segregated away from the DO₃ ordered domains, probably to grain boundaries, and thus provided a strong suppression on grain growth.     

Changes in the hyperfine interactions in the Fe80Nb3Cu1B16 metallic glass under tensile loading

The influence of tensile stress on the changes in hyperfine parameters obtained by Mössbauer spectroscopy of the ferromagnetic amorphous NANOPERM-type Fe₈₀Nb₃Cu₁B₁₆ alloy has been investigated. The bulk changes are obtained by Mössbauer spectroscopy in a transmission geometry using γ-rays; the surface properties are studied in a scattering geometry using conversion electrons. The Mössbauer spectra are analyzed by two distributions of hyperfine inductions, which result in high-field and low-field components corresponding with a model of clusters formed by predominantly iron atoms and intermediate phase containing mainly the Nb, Cu and B atoms. The obtained results are completed by the bulk and surface magnetic measurements, with observations of surface morphology by AFM and microstructure by SEM. The investigations yield approximately linear increase of hyperfine parameters and slight deterioration of the bulk as well as surface magnetic characteristics with tensile loading.     

X-ray and Mössbauer study of rapidly solidified Ce20Fe80 ribbons; effect of the quenching rate

Ce₂₀Fe₈₀ ribbons have been produced by planar flow casting under an He atmosphere at linear wheel velocities between 19 and 29 m s^–1. Analysis of ribbons by X-ray diffraction and⁵⁷Fe Mössbauer spectrometry in the temperature range 77–300 K shows that the ribbons are crystallized. For higher velocities, the ribbon is constituted of the two equilibrium phases CeFe₂ and Ce₂Fe₁₇, but, for lower velocities, there appears a third iron metallic phase, which can be explained by the quenching rate of the melt. A coherent hyperfine parameter set was deduced from fitting Mössbauer spectra in the whole temperature range.     

Characterization of Fe and Fe50Ni50 ultrafine nanoparticles synthesized by inert gas-condensation method

Nanoparticles of Fe and Fe₅₀Ni₅₀ were synthesized by inert gas-condensation method under pure helium atmosphere. The prepared nanoparticles samples were examined by high-resolution transmission electron microscopy, X-ray diffraction and Mössbauer spectroscopy. The synthesized nanoparticles consisted of core-shell type structure nearly spherical shape with a size comprised within the range 4-70 nm and they occur as clusters or chains. The Mössbauer measurements as well as X-ray diffraction showed, in both cases, the presence of iron-oxide phases.     

Comparison of ball milling of Fe/Cr powders and Fe-Cr crystalline alloy

Using the mechanical attrition technique (MA), we have prepared a Fe-Cr alloy starting with a mixture of elemental iron and chromium powders with a nominal composition of 28 at% of Fe and 72 at% of Cr. MA was also performed on solid solutions of Fe₂₈Cr₇₂ crystalline alloy. The Mössbauer effect of the mechanically alloyed powder from Cr and Fe metals has been compared with that from crystalline alloy.     

The influence of Cu and Nb on the crystallization products of annealed FeCuNbSiB

Depending on different Nb and Cu concentration, we studied the formation of nano- and microcrystalline phases in differently annealed samples of FeCuNbSiB. First, the kinetics of crystallization was explored by measuring the temperature-dependent electrical resistivity and magnetization. After this, we collected Mössbauer spectra and did an X-ray diffraction analysis of annealed samples at chosen temperatures to discover the different crystalline phases. It was found how the onset of crystallization had been shifted towards other temperatures. The analysis of Mössbauer spectra shows that building up the well-known DO₃ structure of Fe₃Si is disturbed in the alloy without Cu. At higher Nb content, we resolve two different crystallization steps in the formation of Fe₃Si and a new crystalline phase, probably being a structure like Fe₂₃B₆.     

Recoilless fraction, structural, magnetic and thermal properties of Fe73.5Cu1Nb3Si13.5B9 alloy

Differential scanning calorimetry, X-ray diffraction and room temperature Mössbauer spectrum measurements of Fe_73.5Cu₁Nb₃Si_13.5B₉ (Finemet) alloy have been carried out in order to study its structural and magnetic properties as a function of annealing temperature. The DSC profile of as-quenched Finemet showed two exothermic peaks at 530 and 702 °C, corresponding to two crystallization processes. The Finemet alloy remains amorphous at 450 °C with one broad peak in XRD pattern and one broad sextet in Mössbauer spectrum. When the Finemet alloy was annealed at 550 °C, only well indexed body-center-cubic phase was detected. After being annealed at 650 and 750 °C, the XRD patterns showed the coexistence of α-Fe(Si) and Fe-B intermetallic phases with the increase in XRD peak intensities, indicating the growth of crystallites and the decomposition of Fe_73.5Cu₁Nb₃Si_13.5B₉ alloy at elevated temperatures. The Mössbauer spectra of annealed Finemet alloy could be fitted with 4 or 5 sextets and one doublet at higher annealing temperatures, revealing the appearance of different crystalline phases corresponding to the different Fe sites above the crystallization temperature. The appearance of the nanocrystalline phases at different annealing temperatures was further confirmed by the recoilless fraction measurements.     

Characterization of Fe–Nb sputtered thin films

Structure, composition and chemical behavior of co-sputtered Fe–Nb thin films are analyzed by different techniques, as conversion electron Mössbauer spectroscopy, x-ray photoelectron spectroscopy and x-ray diffraction. It is shown that oxygen is determinative in hindering the Fe–Nb alloy formation and, as a result, Fe_1−xO and Nb₂O₅ occur in significant amounts, even in vacuum. In spite of the oxygen role, a Fe–Nb alloy is formed in little amounts, which increase as the Nb content is increased. The increase of the Nb content is also related with the increase of Fe_1−xO and with a decreasing of the metallic Fe present. Mössbauer data indicate the Fe–Nb phase present is the Fe₂Nb Laves phase.     

Structural and magnetic correlation of Finemet alloys with Ge addition

The correlation between saturation magnetization and the magnetic moment per Fe atom in the nanocrystalline state is studied for Finemet-type alloys. These studies were performed on nanocrystalline ribbons whose compositions were Fe_73.5Si_13.5−xGe_xNb₃B₉Cu₁ (x=8, 10 and 13.5 at%). We used a simple lineal model, X-ray diffraction and Mössbauer spectroscopy data to calculate the magnetic contribution of the nanocrystals and the results were contrasted with the measured saturation magnetization of the different alloys. The technique presented here provides a very simple and powerful tool to compute the magnetic contribution of the nanocrystalline phase to the alloy. This calculus could be used to determine the volume fraction of nanocrystalline and amorphous phases in the nanocrystallized alloy, without using a very sophisticated microscopy method.     

Evolution of structure, microstructure and hyperfine properties of nanocrystalline Fe50Co50 powders prepared by mechanical alloying

Nanostructured Fe₅₀Co₅₀ powders were prepared by mechanical alloying of Fe and Co elements in a vario-planetary high-energy ball mill. The structural properties, morphology changes and local iron environment variations were investigated as a function of milling time (in the 0-200 h range) by means of X-ray diffraction, scanning electron microscopy (SEM), energy dispersive X-ray analysis and ⁵⁷Fe Mössbauer spectroscopy. The complete formation of bcc Fe₅₀Co₅₀ solid solution is observed after 100 h milling. As the milling time increases from 0 to 200 h, the lattice parameter decreases from 0.28655 nm for pure Fe to 0.28523 nm, the grain size decreases from 150 to 14 nm, while the meal level of strain increases from 0.0069% to 1.36%. The powder particle morphology at different stages of formation was observed by SEM. The parameters derived from the Mössbauer spectra confirm the beginning of the formation of Fe₅₀Co₅₀ phase at 43 h of milling. After 200 h of milling the average hyperfine magnetic field of 35 T suggests that a disordered bcc Fe-Co solid solution is formed.     

Structure and magnetic properties of FeMnAl alloys investigated by Mössbauer spectroscopy and X-ray diffraction

The system (Fe_0.88Mn_{0.12 1–x} Al _x has been investigated in a concentration range from 5 to 14 at.% Al. We applied Mössbauer spectroscopy in the temperature range from 4 up to 900 K and X-ray diffractometry at room temperature. The as-cast samples show a bcc phase for all concentrations and exhibit broadened six-line Mössbauer spectra typical for disordered alloys. The Mössbauer spectra during a high temperature treatment show dramatic changes. These are due to ordering processes appearing at temperatures above 700 K. As an example of the observed changes, we present results obtained for the alloy withx= 14 at.% Al.     

Mössbauer and X-ray diffraction studies of mechanically alloyed Fe-Al

Powder samples of Fe₂₅Al₇₅ were prepared by the mechanical alloying method. Mössbauer effect, X-ray diffraction and DSC measurements indicate that Fe and Al crystalline powder transform into Fe-Al amorphous powder with increasing milling time. The X-ray diffraction patterns of the milled Fe₂₅Al₇₅ do not clearly show a sign of the existence of the intermetallic phases or Fe-Al solid solution. However, Mössbauer measurements reveal two sites with hyperfine magnetic fields 30.2 and 26.0 T. These sites form locally during the milling process and then they disappear.     

Study of nanocrystalline and amorphous powders prepared by mechanical alloying

The process of mechanical alloying consists of intimate mixing and mechanical working of elemental powders in a high-energy ball mill. It has been well established that this process is able to produce nanocrystalline and amorphous material. In this study, the structural effects of mechanical alloying of pure Fe, Fe₅₀W₅₀ and Fe₅₀Mo₅₀ powders were investigated by X-ray diffraction and Mössbauer spectroscopy. For all cases, nanocrystalline and/or amorphous fractions were found after milling. The resulting particle size was determined by X-ray diffraction. Pure Fe does not amorphize even after prolonged milling times. For the nanocrystalline powder, significant changes in the linewidth and the hyperfine field are found. Powder mixtures of Fe₅₀Mo₅₀ and Fe₅₀W₅₀ are completely amorphous after milling times of 10 h, as seen by Mössbauer spectroscopy, but nanocrystalline fractions of the non-iron part are still found in X-ray diffraction. Also in the amorphous state, further changes in the hyperfine parameters are found with increasing milling time.     

Structural and magnetic properties of rapidly solidified (Ce0.2Fe0.8)1-x Al x ribbons determined by X-ray diffraction and Mössbauer spectrometry

(Ce_0.2Fe_0.8)_1-x Al _x (0 x 0.9) ribbons have been prepared by planar flow casting under an He atmosphere with a linear velocity of 29 m s^-1. Analyses of the ribbons by X-ray diffraction and⁵⁷Fe Mössbauer spectrometry in the temperature range 4–300 K show that all the ribbons are crystalline. With increasingx, the observed phases are Ce(Fe, Al)₂, Ce₂(Fe, Al)₁₇, CeFe_4+y,Al_8-y and the single fcc aluminium phase. For the different phases, the line intensities of the Mössbauer spectra agree with previous results on the preferential substitution sites for aluminium. A coherent hyperfine parameters set was deduced from fitting spectra in the temperature range 4–300 K.     

Dependence of Magnetic Properties on Composition of Nanocrystalline Fe–M–B–Cu (M: Zr,Nb, Mo,Ti, Ta) Alloys

The specialized rf-Mössbauer technique is used to elucidate the magnetic properties of NANOPERM-type nanocrystalline alloys. The influence of alloy composition on the soft magnetic properties is studied for the Fe₈₀M₇B₁₂Cu₁ (M: Ti, Ta, Nb, Mo, Zr) alloys. The rf-Mössbauer experiments allowed us to distinguish magnetically soft nanoclusters from magnetically harder microcrystalline phases. The measurements performed as a function of the rf field intensity allowed the determination of the distribution of anisotropy fields related to the size distribution of bcc nanoclusters. Smaller anisotropy fields in the nanocrystalline phase were found in Nb-, Zr-, and Mo-containing alloys as compared with the alloys which contain Ti and Ta. The Mössbauer measurements were supplemented by X-ray diffraction determination of the size of nanocrystalline grains.     

Mössbauer Spectroscopy Studies of Some Intermetallics in the Zr–Nb–Fe System

Samples with the following compositions: Zr₆₂Nb₁₄Fe₂₄, Zr₆₅Nb₁₀Fe₂₅ and Zr₅₂Nb₁₀Fe₃₈ were studied by Mössbauer spectroscopy. All of them showed a ternary cubic Ti₂Ni-type phase (QS: 0.30±0.02, IS: –0.14±0.01) and traces of Zr₂Fe phase (QS: 0.86±0.03, IS: –0.29±0.01). Zr phase (QS: 0.22±0.01, IS: –0.11±0.01) was also detected except in the case of the richer Fe sample. In addition to these expected phases, a hexagonal MgZn₂-type phase was determined. The assigned parameters for this phase are: QS: 0.38±0.04, IS: –0.28±0.02. These results suggest a revision of the diagram.     

Mixed valence of iron in natural vonsenite

The exchange of electrons between adjacent ions in different oxidation states in vonsenite was observed using Mössbauer spectroscopy. The Mössbauer spectra of a series of naturally occurring vonsenite were recorded over a temperature range of 120–773 K. Four quadrupole doublets were resolved by computer fitting and assigned to Fe²⁺(Fel), Fe²⁺(Fe3), Fe³⁺(Fe2, Fe4) and Fe²⁺-Fe³⁺(Fe2–Fe4). The percentage of iron sites participating in an electron exchange process increases from 17% between 120 and 298 K to 27% between 573 and 773 K.     

Structural characterization and magnetoimpedance effect in amorphous and nanocrystalline AlGe-substituted FeSiBNbCu ribbons

Two series of rapidly solidified FINEMET (Fe_73.5Si_13.5B₉Nb₃Cu₁) alloys with and without partial substitution of Al (1.5 at%)/Ge (1 at%) were prepared by melt-spinning technique. The nanocrystallization process was carried out by the heat treatment of the as-spun ribbons at 560 °C for 1 h in a vacuum furnace. X-ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimeter (DSC), Mössbauer spectroscopy, and magnetoimpedance (MI) measurements were conducted on the as-quenched and heat-treated alloys to investigate their structural and magnetic properties. The average crystallite sizes obtained for the heat-treated samples were in the range of 10–12 nm as confirmed by our XRD and TEM data. The ultrasoft magnetic behavior observed for the Al/Ge-substituted nanocrystalline alloys was confirmed both by our magnetic data and magnetoimpedance ratio (MIR%) results. A twofold increase in the magnitude of the MIR% (99%) was observed for the Al/Ge-substituted nanocrystalline alloy against that of the pure FINEMET alloy (∼48%) measured at 5.5 MHz. This is believed to be related to the decrease of the magnetocrystalline anisotropy as well as magnetostriction decline due to the Al substitution for Fe atoms in this nanostructured alloy.