Polymerization of Styrene Initiated by 1,4-Dimethyl-1,4-bis(p-anisyl)-2-tetrazene

Abstract

The polymerization of styrene (St) initiated by 1,4-dimethyl-1,4-bis(p-anisyl)-2-tetrazene (1a) was studied kinetically in benzene. The polymerization proceeds through a radical mechanism. The rate of polymerization is proportional to [1a]^0.5 and [St]^1.0. The overall activation energy for the polymerization is found to be 81.2 kJ/mol within the temperature range of 65 to 80°C. The activation parameters for the decomposition of 1a at 70°C are k_d = 1.88 × 10^?5s^?1, δH? = 133.1 kJ/mol, and δS? = 29.9 J/mol·deg.     

The Separation and Determination of Molybdenum by Electron Paramagnetic Resonance

Abstract

A procedure is described for the separation and quantitative determination of molybdenum by means of EPR. Molybdenum(VI) was precipitated from a hydrochloric acid solution (1.5 Molar) with α-benzoinoxime. The precipitate was separated by centrifugation and then the sample was dried in an oven at 105°C. Nitrogen was passed over the sample to complete the drying procedure. The precipitate was dissolved in acetonitrile which was 0.5 M in lithium perchlorate. Electrochemical reduction of the sample produced the molybdenum(V) species. The concentration of molybdenum(V) was determined directly from the intensity of the first derivative EPR signal. The range of linearity of the analytical curve was 1.00 × 10^?2 M to 1.00 × 10^?4 M, and a routine accuracy of less than 6% was obtained.     

A Dual-Enzyme Electrode for the Determination of Flavin Adenine Dinucleotide in the Presence of Riboflavin and Flavin Mononucleotide

Abstract

An electrode method has been developed for the determination of flavin adenine dinucleotide (FAD) using a potentiometric gas sensor and commercially available enzyme preparations. The construction of the FAD-sensitive electrode is based on immobilizing alkaline phosphatase (E.C. 3.1.3.1) and adenosine deaminase (E.C. 3.5.4.4) on the sensing tip of an ammonia gas sensor. Alkaline phosphatase enzymatically catalyzes the hydrolysis of FAD to adenosine which is subsequently converted to ammonia by adenosine deaminase. The response of the dual-enzyme electrode is linear between 8 × 10^?5 M and 4 × 10^?3 M FAD with a slope of 43 mV/decade concentration at pH 8.5 and 37[ddot]C. The optimum buffer system is 0.5 M diethanolamine, 1 × 10^?3 M Tris-HCl and 1 × 10^?3 M MgCl₂. Electrodes constructed with enzymes immobilized by cross-linking with glutaraldehyde and bovine serum albumin showed longer life times than electrodes using enzymes entrapped by a dialysis membrane. The electrode is highly selective over riboflavin and flavin mononucleotide, but it does respond to other nucleotides.     

Use of the Rotated Ring Disc Electrode for the Analytical Determination of Dithiaalcanediols in Aquo-Alcoholic Media and Its Rate of Oxidation with Bromine

Abstract

We used bromine generated and detected on the ring-dise electrode for the titration of aquo-alcoholic solution of dithiaalcanediol. The analysis of the ring current vs disc current curve provided a means of determination of the rate constant k of the second order homogeneous and fast reaction of bromine with each of the two sulfide groups of dithiaalcanediol. A value of (3+1)× 10^?6M^?1 _s ^?1 was found for k at 25°C.     

Arginine Determination with Ion-Selective Membrane Electrodes

Abstract

A new method for the determination of the amino acid arginine utilizes a dual enzyme catalyzed reaction monitored with an ammonium ion selective membrane electrode of the antibiotic type. The technique gives a linear correlation between arginine concentration and electrode response over the 3 × 10^?3 M to 3 × 10^?5 M range and a useful, but non-linear, response over a wider range. Major interferences are urea, K⁺, and NH₄ ⁺, but Na⁺ does not interfere in the physiological concentration range.     

Use of Catecholoxygenase for Determination of Catechol

Abstract

A cell extract from Trichosporon cutaneum containing catechol 1,2-oxygenase catalyzes the oxidation of catechol to cis,cis-muconic acid. The absorbance of the cis,cis-muconic acid at 260 nm can be correlated with the initial catechol concentration in the range 5 × 10^?6 M to 5 × 10^?5 M in aqueous solutions. This enzymatic assay has been applied to the determination of catechol in aqueous samples derived from coal processing.     

Free Radical Ring-Opening Polymerization of 4-n-Hexyl- and 4-n-Decyl-2-methylene-1,3-dioxolanes

Two alkyl-substituted cyclic ketene acetals, 4-n-hexyl-2-methylene-1,3-dioxolane (4) and 4-n-decyl-2-methylene-1,3-dioxolane (6), were shown to undergo free radical ring-opening polymerization with the introduction of an ester group into the backbone of an addition polymer. The spontaneous polymerization of 4 (presumable by an ionic mechanism) produced a polymer containing no ring-opened units; furthermore 4 and 6 could be stabilized with respect to spontaneous polymerization by the addition of small amounts of pyridine. On the other hand, the polymerization of 4 in a 50% (by weight) benzene solution at 110°C with di-tertbutyl peroxide as the catalyst gave quantitative ring opening to give a polyester containing both possible isomeric ring-opened units. Bulk polymerization of 4 at 60°C at 53% conversion gave 50% ring opening which was divided 31% to 19% between cleavage to give the intermediate secondary free radical and the intermediate primary radical. Copolymerization of 4 with equimolar quantities of styrene at 110°C gave at 56% conversion a copolymer consisting of 67% styrene units, 22% ester-containing units resulting from cleavage to form a secondary radical, 7% of the isomeric ester-containing units, and 4% nonring-opened units. Polymerization studies with monomer 6 gave results very similar to those obtained with 4.     

Studies on Aqueous Polymerization of Acryionitriie Initiated by Ce(IV)-Amino Acid Redox Pair

Aqueous polymerization of acryionitriie initiated by the Ce(IV)-glycine redox pair was studied at 35°C under nitrogen. The rate of polymerization, R_p, was found to be approximately proportional to the square of the monomer concentration within the range of 0.140s–1.268 M. R was also found to increase with glycine concentration in the interval 0.1 to 0.4 M and decrease with cerie ion concentration. The activation energy was estimated to be 25.8 kcal/mol. A suitable kinetic scheme was proposed and explained in the light of these experimental findings. The end-group in the polymer was characterized by IR spectra, and the average molecular weight of the polymer was found to be 84,100.     

Asymmetric Synthesis of Phosphinous Tungsten Complexes

Abstract

The asymmetric synthesis of phosphinous compounds from diheterophosphacycloal kane-1,3,2 was investigated in a transition metal complex series. Complexes 1 and 2 were prepared from diaminophosphine, (?)-ephedrine and W (CO)₅ THP (1: δ³¹ P=+147,6 ppm; J_PW=313 Hz M^.+=595;2 δ³ p=+156 ppm J_PW=304 Hz M^.+=533; 90%dp) in two steps. Methyl lithium reacted with 1 to give stereospecific 3 (83%Yield) by P-O linkage (3 δ³¹ P=+64 ppm; J_PW =261 Hz; M^.+ ? 28=583). The aminophosphine complex 3 was stereochemically stable and was used for studies of synthetic applications. HCL gas reacted with 3 in CH₂Cl₂ to give the non optically active chlorophosphine complex 4 (δ³¹ P=+103,6 ppm; J_PW=290 Hz; M^.+ =482). This compound immediately gave salt 6 (δ³¹ P=+66,7 ppm; J_PW =240 Hz) by reaction with (?)-menthol and triethylamine. The acid methanolysis of 3 gave a mixture of 5 and 6 and the unchanged (?)-ephedrine salt [5:30% yield; δ³¹ P=+114 ppm; J_pw=280 Hz; [α]_D=+1,2° (CH₂Cl₂); M^.+=478; 6 : 60% yield; δ³¹p=+102,9 ppm; J_PW=264 Hz; [α]_D =+16,9° (CH₂Cl₂); M^.+=464]. Compound 6 was thus obtained with a 80% yield and a specific rotation of + 20,2° (CH₂Cl₂) in isopropanol/H₂SO₄ 5M medium. The enantiomeric excess of 6 was determined by RMN³¹P. Acid hydrolysis of 3 or the reaction with CH₃SO₃H, gave phosphinous acid complex 6 with an optical rotation of + 4,8° or ?1,8° respectively. These results provide precious informations about the stereochemistry and reactivity of the P-N linkage in this aminophosphine transition metal series, which differs notably from that of the corresponding (PO) N bond.     

The structure of cis and trans lsomers of 1-(p-Bromobenzylidene)-2-indanone

Abstract

In this communication we wish to report an interesting case of the isolation and characterization of the cis and trans isomers of 1-(p-bromobenzylidene)-2-indanone and their ketals. Prior to this work, Hoogstreen and Trenner² had reported on the cis and trans isomers of 1-(p-chlorobenzylidene)-2-methyl-5-methoxyindenylacetic acid. The condensation of 2-(N-morpholinyl)-indene (1, prepared by the reaction of 2-indanone³ and morpholine) with P-bromobenzaldehyde was conducted by refluxing them in the presence of acetic acid for 4 hours. Acid hydrolysis of the reaction mixture followed by dry column chrcmatography over sillica gel using a fraction collector afforded two iscmeric monobenzylidenes, compounds 2(36.6%, mp 110–111°)and 3(1.3%, mp 115–116°) and a dibenylidene, compound 4 (8.7%, mp 205°). The relative rations of the mono- and dibenzylidenes seemed to depend on the reaction conditions. Higher yields of the monobenzylidenes 2 and 3 were obtained by conducting the reaction in the presence of UV light. The structures of these monobenzylidenes were established as cis and trans isomers of 1-(p-bromobenzylidenes)-2-indanone on the Basis of elemental analyses and ir and nmr spectroscopy. The ir spectra⁴ (CHCl₃)

of compounds 2 [1725 (c=0), 1620 (c=c)cm^?1] and 3[1710 (c=o), 1570, 1600 (c=c) cm^?1] were consistent with the structures. The molecular ion peaks as well as the fragmentation patterns in the mass spectra of both these compounds were consistent with the assigned structures. Before going into the omr discussion it should be pointed out that treatment of compound 2 with athylene glycol in the presence of p-toluene sulfonic acid produced two ketals, 5 (38.3% mp, 118–120°) and 6 (30.6% mp, 125–126°). As depicted; the ketals 5and 6 were also found (by omr) to be related to each other as cis and trans isomers. Furthermore, each of them could be hydrolyzed with acid to the corresponding monobenzylidenes 2 and 3 without any isomerization. However, UV irradiation of compounds 2 and 3 gave equilibrium mixtures containing both the isomers, indicating isomerization had occurred under photolytic conditions.     

Extraction-Photometric Determination of Niobium(V) by Reaction with Pyrocatechol and Thenoyltrifluoracetone

Abstract

The possibility of formation of mixed complex compound niobium(V)-pyrocatechol (PC)-thenoyltrifluoracetone (TTA) has been shown. Optimum conditions for the formation of such a compound have been found (7.5 M HCI, 0.3 MTTA, 0.4 MPC) and the molar ratio Nb (V):PC:TTA=1:2:2 has been established by the equilibrium shift method. The absorption spectrum of the chloroform extract of the Nb-PC-TTA compound has a maximum at 414 nm, ε= (7.7±0.2) × 10³. The influence of other ions on extraction-photometric determination of niobium (V) with PC and TTA is discussed.     

Highly Selective Potassium Ion Responsive Liquid-Membrane Electrode

Abstract

The performance of a new liquid-membrane electrode using valinomycin as membrane component is described with respect to selectivity, working range, speed of response and accuracy. The electrode makes possible the measurement of potassium ion activities in the range of 10^?1 M to at least 10^?6 M in unbuffered systems with a selectivity of potassium over sodium ions of more than 4,000. The electrode was used for the direct titration of potassium ions.     

Oxygenation of Trimethylsilylallenes Readily Obtainable from Organoboranes. Syntheses of 1-Trimethylsilyl-1-alkyn-3-ones and 1-Trimethylsilyl-1-alkyn-3-ols

Abstract

Recently we have reported that the reaction of sodium methoxide with ate-complexes (1) readily prepared from trimethyl-silylpropargyl phenyl ether and organoboranes gives trimethyl-silylallenes (2) selectively (eq. 1).¹ In an attempt to find a new synthetic application of such silylallenes (2), the oxidation of 2 was examined. Although the usual oxidants such as m-chloro-perbenzoic acid were found to be unsuitable for the oxidation of the silylallenes, it was discovered that 2 was autoxidized at room temperature to propargylic hydroperoxide (3) (eq. 2). For example, the acidified starch-iodine test² strongly suggested the presence of the organic hydroperoxide in the reaction mixture obtained from 1,2-heptadienyltrimethylsilane (2, R=Bu) and oxygen. The hydroperoxide (3, R=Bu) was isolated in a 40% yield by distillation, 45–48 [ddot]C/0.1 mmHg. In the infrared spectrum, the OH stretching frequency appears at 3430 cm^?1 and the C°C at 2180 cm,^?1     

Photoinduced Graft Copolymerization. V. Graft Copolymerization of Methyl Methacrylate onto Cellulose in the Presence of N-Bromosuccinimide as Initiator

Abstract

The photoinduced graft copolymerization of methyl methacrylate onto cellulose was studied using N-bromosuccinimide as the photoinitiator. The formation of graft copolymer increases with an increasing amount of cellulose. The graft copolymerization increases with increasing initiator concentration up to 1,25 × 10^?2 M and thereafter it decreases. The percentage of graft increases with increasing monomer concentration up to 46.9 × 10^?2 M and thereafter it decreases. The percentage graft-on increases with increasing temperature. The overall activation energy was computed to be 8.40 kcal/mol. The percentage graft was investigated using different water-miscible organic solvents. The graft copolymerization was also investigated using differently modified cellulose. A possible mechanism for the photo-graft copolymerization onto cellulose is suggested.     

A Stereoselective and Regioselective Total Synthesis of (π)-Trichodiene

Trichodiene (1), a sesquiterpene hydrocarbon, was isolated and characterized by Nozoe and Machida in 1970.¹ Trichodiene (1) has been shown to be the biogenetic precursor of the trichothecane family of sesquiterpenoids characterized by the cytotoxic fungal metabolite (–)-trichodermin (2).^2,3 We recently reported a total synthesis of (±)-trichodiene (1) via lactone 3.⁴ Now, we wish to report another stereoselective total synthesis of (±)-trichodiene (1) via lactone 3 which is highly regioselective.     

New Homologation Procedures of Carbonyl Compounds by Means of Diethyl[trimethylsilylethoxymethyl]phosphonate

Abstract

The lithiated carbanion of the phosphonate 1 prepared by means of s-BuLi at -78°C in THF can be treated with C1Si(CH₃)₃ transforming 1 into its α-Si(CH₃₎₃ substituted derivative 2. Whereas the anion of 1 is thermally unstable at temperatures exceeding -70°C the preparation of the corresponding carbanion of 2 by means of s-BuLi and the subsequent reaction with carbonyl compounds can be carried out at temperatures about -30°C illustrating the carbanion stabilizing effect of the α - silyl group. The phosphonate 2 is very suitable to effect conversion of many aldehydes and ketones via the vinylphosphonate-type 3 (applying a Peterson elimination) either to the homolocles esters 4 or the special α -hydroxyesters 5.     

A Total Synthesis of (±)-Trichodiene

Trichodiene (1), a sesquiterpene hydrocarbon, was isolated from the extract of mycelium of Trichothecium roseum. The structure of trichodiene (1) was elucidated by Nozoe and Machida in 1970 via degradation and spectroscopy.¹ Trichodiene (1) has been shown to be the biogenetic precursor of the trichothecane family of sesquiterpenoids as characterized by the cytotoxic fungal metabolite (-)-trichodermin (2).^2,3 The structure and absolute stereochemistry of (-)-trichodermin (2) were determined by X-ray diffraction and, therefore, the structure and absolute stereochemistry of trichodiene (1) are now firmly established.⁴ We wish to report a total synthesis of (±)-trichodiene (1) via previously reported lactone 3.^5,6     

An Improved Total Synthesis of (±) - Podocarpic Acid by a Cyclialkylation Route

A number of total syntheses of (±) - podocarpic acid (i) have been described¹ King, King and Topliss² first identified one of the products from nonstereo-selective cyclization of (4) with polyphosphoric acid as (±)- ethyl-O-methylpodocarpate (2) and correlated that with the corresponding acid (3), prepared in an extremly poor yield (ca 0.4%)³ by Bhattacharyya³, and Haworth and Moore⁴ by cyclization of (5) with a mixture of sulfuric acid and acetic acid. More recently Mancini, Fringuelli and Taticchi⁵ prepared (3) (in 4.8% yield) by repeating Howorth¹ s cyclization of (4). In continuation of our studies on cyclialky-     

A Total Synthesis of the Antifungal Mold Metabolite (±)-LL-Z1271α

The mold metabolite (-)-LL-Z1271α (10a) was isolated from the fermentation products of an Acrostalagmus species and was found to exhibit antifungal activity toward several pathogenic fungi.¹ We wish to report a total synthesis of (±)-LL-Z1271α (10a).²     

Human Isoionic Hemoglobin: Preparation and Kinetic Properties

Abstract

Much of the data on hemoglobin-gas interactions which have accumulated in the literature is difficult to interpret because the hemoglobin preparations contained extraneous ligands and salts. In order to obtain hemoglobin which is completely free of 2, 3-DPG and other ionic substances, we have developed a method for isolating isoionic hemoglobin. These data serve as a baseline against which other data obtained with added ligands and salts can be compared.

Specifically, isoionic hemoglobin had these properties: Second-order rate constant for combination with 0₂: 2.2 × 10⁷ M^?1S^?1; p₅₀ at 20^[ddot] was 0.87mm Hg at heme concentration of 10^?4 M.