Investigation on properties of aqueous foams stabilized by aliphatic alcohols and polypropylene glycol

Foams stabilized by nonionic surfactants are usually moderately stable due to high drainage rate and intense bubble coalescence and coarsening. This study aimed to investigate comparatively the foam properties of aliphatic alcohols (methyl isobutyl carbinol (MIBC) and 2-octanol) and polypropylene glycol (PPG400). Experiments were conducted using the FoamScan method at various surfactant concentrations and gas flow rates where the foam volume, liquid content of foam and foam half-life were determined. The results showed that both foamability and foam stability of surfactant solution increased with increasing gas flow rate and surfactant concentration for all tested surfactants. PPG400 was an unusually strong surfactant having the largest surface activity compared with MIBC and 2-octanol, which exhibited the maximum foaming performance and foam stability at all tested gas flow rates and concentrations. The present study suggested that foam properties depended primarily on the type of surfactant and its concentration and secondarily on the gas flow rate. In addition, properties of interface are closely related to that of foam, which is a significant point if one wants to produce foams for specific applications.     

Sol–gel silica antireflective coating with enhanced abrasion-resistance using polypropylene glycol as porogen

Silica antireflective (AR) coatings with high transmittance and enhanced abrasion-resistance were synthesized by sol–gel process using polypropylene glycol (PPG) as porogen. The effects of molecular weight of PPG and weight ratio of PPG to SiO₂ on the refractive index and abrasion-resistance of the coating were systematically studied and compared with those of polyethylene glycol (PEG). Experimental data showed that the refractive index decreased with increasing the weight ratio to SiO₂ and molecular weight of both PEG and PPG, but PPG was much more effective than PEG. In the case of same molecular weight, PPG modified coating has the higher porosity than PEG modified one. When the weight ratio of PPG to SiO₂ is in a low level, the PPG-containing silica AR coatings exhibit the good abrasion-resistance. PPG is liquid at room temperature and the better solubility than PEG. These effective and economic AR coatings with enhanced abrasion-resistance have potential value in the field of solar thermal collectors.     

Marangoni effects in aqueous polypropylene glycol foams

The foam behavior of three polypropylene glycols covering the molecular weight range between 192 and 725 g/mol has been examined. Static and dynamic surface tension data, as well as bubble size distribution and retention time in the foam, were incorporated into a simple model of foam stability. The latter clearly indicates that surface tension differences between the plateau border and lamellar region adjacent to the bubble surface are the dominant factor in controlling foamability, causing liquid flow in the direction opposite to liquid drainage, a process termed the Marangoni effect.     

Protein foam application for enhanced oil recovery

Protein foam was explored as a foaming agent for enhanced oil recovery application in this study. The influence of salinity and oil presence on bulk stability and foamability of the egg white protein (EWP) foam was investigated. The results were compared with those of the classical surfactant sodium dodecyl sulfate (SDS) foam. The results showed that the EWP foam is more stable than the SDS foam in the presence of oil and different salts. Although, the SDS foam has more foamability than the EWP foam, however, at low to moderate salinities (1–3 wt% NaCl), both foam systems showed improvement in foamability. At a NaCl concentration of 4.0 wt% and above, foamability of the SDS foam started to decrease drastically while the foamability of the EWP foam remained the same. The presence of oil has a destabilizing effect on both foams but the EWP foam was less affected in comparison to the SDS foam. Moreover, increasing the aromatic hydrocarbon compound percentage in the added oil decreased the foamability and stability of the SDS foam more than EWP foams. This study suggests that the protein foam could be used as an alternative foaming agent for enhanced oil recovery application due to its high stability compared to the conventional foams.     

Estimation of the molecular weights of noncovalent columnar polymers based on β-cyclodextrin by the measurement of the aggregation rate of their polymer inclusion complexes with polypropylene glycol

Noncovalent columnar polymers (NCPs) based on cyclodextrins (CD) are polymeric assemblies of molecules that have continuous hollow channels, the width of which is determined by the diameter of the cavity of the initial CDs. The repeating fragment in an NCP is the CD molecule. For NCPs that were obtained by the exclusion of polymer backbone macromolecule from the corresponding inclusion complexes (ICs) based on β-cyclodextrin (NCP_excl), the polymer length, expressed as the number of macrocycles in a single chain (n) is determined by the size of the included ligand, polypropylene glycol (PPG), and is the PPG polymerization degree divided by two. The determination of the molecular weight of an NCP obtained by the precipitation method (NCP_prec) is rather difficult, since they are present in the aggregated state rather than in the form of individual molecules in solution. To estimate the molecular weight of NCP_prec, an indirect method is used, which is based on the determination of the aggregation rate of the ICs formed as a result of the interaction between an NCP and polypropylene glycol with a fixed molecular weight (MW), in this case PPG 1000. The comparison of the aggregation rates of the inclusion between NCP_excb (which were synthesized using PPGs with different molecular weights) and PPG 1000 with the aggregation rate of the inclusion complex on the basis of NCP_prec provided the estimation for the MWs of single polymer chains. The fact that the samples of NCPprec contain ∼30% of the monomeric β-CD was taken into account when constructing the calibration curve. It was demonstrated that the MW of the polypropylene glycol corresponding to NCP_prec is 1320 Da. Consequently, ∼11–12 molecules of β-CD are included in the single chains of NCP_prec.     

Competitive Destabilization/Stabilization of β‐Lactoglobulin Foam by PEO‐PPO‐PEO Polymeric Surfactants

The effect on β‐lactoglobulin foamability and foam stability of the poly(ethylene oxide)‐poly(propylene oxide) block copolymers F127 (PEO₉₉‐PPO₆₅‐PEO₉₉), molecular weight 12500 g/mol, and P85 (PEO₂₆‐PPO₃₉‐PEO₂₆), molecular weight 4600 g/mol, has been investigated at constant protein concentration, 10 µM (0.2 mg/L), and varying block copolymer concentrations, ranging from 0.02 to 1600 µM. Foam was generated by means of air sparging and the foam volume and liquid volume of the foam were measured for one hour. It was found that foam stabilized by F127 or P85 in the concentration range 20–1600 µM contained a larger liquid volume initially than pure β‐lactoglobulin foam. Furthermore, β‐lactoglobulin foamability was only marginally affected by the presence of F127, while it was reduced in an interval of low P85 concentrations. The protein foam stability was retained in the presence of the larger polymer F127, whereas P85 largely reduced the stability, indicating that the size of the polymeric surfactant is important. The results are discussed in relation to surface rheological properties and forces acting across foam films. Steric repulsion generated between the surfaces of foam films is suggested to be the main stabilizing factor in dry foam containing F127. The instability of the mixed β‐lactoglobulin/P85 system is suggested to be caused by two effects. First, there are incompatible stabilization mechanisms of block copolymer and protein, as supported by previous surface rheological data. Second, there is a reduced importance of long‐range steric repulsion when P85 is added, compared to the case where F127 and β‐lactoglobulin are mixed.     

Dielectric secondary relaxations in polypropylene glycols

Broadband dielectric measurements of polypropylene glycol of molecular weight M(w)=400 g / mol (PPG 400) were carried out at ambient pressure over the wide temperature range from 123 to 353 K. Three relaxation processes were observed. Besides the structural alpha relaxation, two secondary relaxations, beta and gamma, were found. The beta process was identified as the true Johari-Goldstein relaxation by using a criterion based on the coupling model prediction. The faster gamma relaxation, well separated from the primary process, undoubtedly exhibits the anomalous behavior near the glass transition temperature (T(g)) which is reflected in the presence of a minimum of the temperature dependence of the gamma-relaxation time. We successfully applied the minimal model [Dyre and Olsen, Phys. Rev. Lett. 91, 155703 (2003)] to describe the entire temperature dependence of the gamma-relaxation time. The asymmetric double-well potential parameters obtained by Dyre and Olsen for the secondary relaxation of tripropylene glycol at ambient pressure were modified by fitting to the minimal model at lower temperatures. Moreover, we showed that the effect of the molecular weight of polypropylene glycol on the minimal model parameters is significantly larger than that of the high pressure. Such results can be explained by the smaller degree of hydrogen bonds formed by longer chain molecules of PPG at ambient pressure than that created by shorter chains of PPG at high pressure.     

Surface-assisted laser desorption/ionization mass spectrometry (SALDI-MS) of low molecular weight organic compounds and synthetic polymers using zinc oxide (ZnO) nanoparticles

We have developed surface-assisted laser desorption/ionization mass spectrometry using zinc oxide (ZnO) nanoparticles with anisotropic shapes (ZnO-SALDI-MS). The mass spectra showed low background noises in the low m/z, i.e. less than 500 u region. Thus, we succeeded in SALDI ionization on low molecular weight organic compounds, such as verapamil hydrochloride, testosterone, and polypropylene glycol (PPG) (average molecular weight 400) without using a liquid matrix or buffers such as citric acids. In addition, we found that ZnO-SALDI has advantages in post-source decay (PSD) analysis and produced a simple mass spectrum for phospholipids. The ZnO-SALDI spectra for synthetic polymers of polyethylene glycol (PEG), polystyrene (PS) and polymethylmethacrylate (PMMA) showed the sensitivity and molecular weight distribution to be comparable to matrix-assisted laser desorption/ionization (MALDI) spectra with a 2,5-dihydroxybenzoic acid (DHB) matrix. ZnO-SALDI shows good performance for synthetic polymers as well as low molecular weight organic compounds.     

Investigations on foamability of surface-chemically pure aqueous solutions of functionalized alkylaldonamides

The foamability of the aqueous solutions of functionalized, surface-chemically pure surfactants of the nonionic saccharide-type: N,N-di-n-alkylaldonamides, N-alkyl-N-(2-hydroxyethyl)aldonamides, and N-cycloalkylaldonamides, derivatives of D-glucono-1,5-lactone and/or D-glucoheptono-1,4-lactone, were investigated. The approach of Lunkenheimer and Ma?ysa for the characterization of the foamability and foam stability of these surfactant solutions was applied for these investigations. Using standard parameters related to the different physical stages of the foaming process, foam stability can be described in a simple and easy manner. In general, the investigated alkylaldonamides form foams of medium stability. However, for some homologues a transition from unstable to stable foam systems is observed with increasing concentration. Modifications of the molecular structure of the alkylaldonamides are distinctly reflected in their foam properties. This fact concerns not only changes of the hydrophobic moiety and its functionalization but also slight variations of the saccharide residue. Each homologous series reveals an exceptional foam behavior. In the case of the N,N-di-n-alkylaldonamides the increase of the n-alkyl chain length is accompanied by an increase of the foam stability. The aqueous solutions of the N-alkyl-N-(2-hydroxyethyl)aldonamides reveal most favorable foaming properties for homologues with average alkyl chain lengths. Moreover, it was found that the occurrence of a phase transition in the adsorption layers of the N-cyclooctylgluconamides previously observed by surface tension and surface potential measurements is also remarkably reflected in their foam stability.     

Effects of surfactant and molecular weight of polyol on grating formation and switching of holographic PDLC

The interposition of surfactants between polymer and liquid crystal (LC) droplets was theoretically predicted by the positive spreading coefficient (0 < λ₃₁) and utilized to interpret the morphology, grating formation kinetics, diffraction efficiency, and switching of the holographic polymer dispersed liquid crystal (HPDLC), prepared from various types (octanoic acid, poly oxyethylene octyl phenyl ether, and perfluoro‐1‐butanesulfonyl fluoride) and amounts (0–9 wt%) of surfactant and molecular weights of polyol (PPG). Regardless of the surfactant type, diffraction efficiency increased with the addition and increasing amount of surfactant, a tendency consistent with increasing value of spreading coefficient, which is determined by the formulations of grating formation. In contrast, diffraction efficiency showed a maximum with the polypropylene glycol (PPG) molecular weight. Surfactant effectively reduced the anchoring energy and electrically drove the film which otherwise was not driven. Overall, surfactant with greater λ₃₁ gave smaller droplet, greater diffraction efficiency, driving voltage, contrast ratio, and smaller response time. Copyright © 2008 John Wiley & Sons, Ltd.     

Desorption electrospray ionisation mass spectrometry and tandem mass spectrometry of low molecular weight synthetic polymers

A range of low molecular weight synthetic polymers has been characterised by means of desorption electrospray ionisation (DESI) combined with both mass spectrometry (MS) and tandem mass spectrometry (MS/MS). Accurate mass experiments were used to aid the structural determination of some of the oligomeric materials. The polymers analysed were poly(ethylene glycol) (PEG), polypropylene glycol (PPG), poly(methyl methacrylate) (PMMA) and poly(alpha-methyl styrene). An application of the technique for characterisation of a polymer used as part of an active ingredient in a pharmaceutical tablet is described. The mass spectra and tandem mass spectra of all of the polymers were obtained in seconds, indicating the sensitivity of the technique.     

FOAMABILITY OF PEO-PPO-PEO TRIBLOCK COPOLYMERS (P85 AND F108) AND ROLE OF THE FOAM FILMS

The foamability of two commercial PEO-PPO-PEO triblock copolymers (Synperonic P85 and F108, ICI) was studied and compared to the properties of single foam films. The volume of a steady-state foam column created with a combined pneumatic-mechanical device is used as a measure of the copolymers foamability. Experiments were carried out at bulk copolymer concentrations corresponding to full surface coverage, i.e. constant area per molecule, under equilibrium conditions. The foamability of F108 solutions was higher than that of P85 although the surface activity of both copolymers was similar. The foam volume increases with increasing the bulk copolymer concentration. Higher electrolyte concentration or lower pH caused the foam volume to diminish. A pronounced parallelism between the properties of dynamic foams and single microscopic foam films was observed: when thicker single foam films were formed (from F108 solutions) the steady     

The Effect of Macromolecules on Foam Stability in Sodium Dodecyl Sulfate/Cetylpyridinium Bromide Mixtures

Abstract

The effects of macromolecules, gelatin, and polyvinylpyrrolidone (PVP), on the properties of foam comprising sodium dodecyl sulfate (SDS) and cetylpyridinium bromide (CPDB) have been studied by measurements of foamability, foam stability, surface tension, and solution specific viscosity. The results indicate that foamability and foam stability are significantly improved when macromolecules are added into mixed systems. Both gelatin and PVP associate with SDS/CPDB surfactants and form aggregates. Electrostatic repulsion and steric stabilization between the two sides of the foam lamellae, due to aggregation, and prevention of drainage in the lamellae, achieved by the long chains of macromolecules are the reasons for increasing foamability and foam stability. The interactions between PVP and surfactants is weaker than those between gelatin and surfactants. The strongest association between macromolecules and surfactants occurs when the molar ratio of SDS/CPDB is 1:1. By comparing PVP with gelatin, the former is favored to increase foamability, and the latter is favored to increase foam stability.     

A multi point conductivity measurement system for characterisation of protein foams

Protein foams play an important role in both food and biotechnological processes. A sound understanding of foaming properties of proteins relevant to such processes is useful e.g. to allow adequate control of unwanted foams and appropriate choice of protein-physical system when foams of certain characteristics are required. In general, measurements of changes in foam volume (volumetric method) are used for foam characterisation. However, recently there has been increased interest in the use of measurement methods based on conductivity and capacitance. Simple relative techniques based on electrical conductivity measurements provide information on both foamability and foam stability. A multi point conductivity measurement system has been designed and used for characterisation of model protein foams (0.1 and 1.0 mg ml⁻¹ Bovine serum albumin, BSA). The solution of BSA was sparged with nitrogen or carbon dioxide gas at constant flow rate (90 cm³ min⁻¹) via a stainless steel sinter (0.5 or 2.0 μm in pore size). A comparison of foaming properties determined by volumetric and conductimetric techniques is provided. Both methods show that more stable foams are obtained for solutions at higher BSA concentrations. At all BSA concentrations, higher foamability and stability are achieved with a smaller sinter pore size. When nitrogen rather than carbon dioxide is used as a dispersed phase, higher foamability and foam stability are obtained. The conductivity measurements indicate that foamability is dependent on gas type, whereas, volumetric measurements do not show such differences.     

Grafting onto ultrafine ferrite particles: Reaction of isocyanate-capped polypropylene glycol with hydroxyl groups on the surface

The grafting of polypropylene glycol (PPG) onto an ultrafine ferrite by the reaction of hydroxyl groups on the surface with isocyanate-capped PPG (PPG-NCO), prepared by the reaction of an equimolecular amount of PPG with tolylene 2,4-diisocyanate, was investigated. When PPG-NCO (M _n=2.5×10³) was heated with the ferrite in bulk, the percentage of grafting onto the ferrite at 120 °C was increased up to 18.5%. On the contrary, the grafting by the reaction of PPG with hydroxyl groups on the ferrite at 120°C was scarcely observed. The grafted PPG onto the ferrite was removed by hydrolysis with a dilute methanol solution of potassium hydroxide. Therefore, it was considered that PPG was grafted onto the ferrite surface with urethane bond. The grafting of PPG onto the surface was also confirmed by infrared spectra. The reaction of PPG-NCO with the ferrite was accelerated by the addition of-picoline as a catalyst. PPG-grafted ferrite was found to produce a stable colloidal dispersion in organic solvents. Furthermore, the effect of molecular weight of PPG-NCO on the grafting onto the ferrite was discussed.     

Plasticization of biodegradable stereocomplex polylactides with poly(propylene glycol)

The plasticization of stereocomplex polylactide (scPLA) with poly(propylene glycol) (PPG) is described. The poly(L-lactide) (PLLA), poly(D-lactide) (PDLA) and PPG were completely blended in chloroform before film casting to prepare scPLA/PPG blend films. The PLLA/PDLA ratio was fixed at 50/50 (w/w). The PPG blending enhanced the stereocomplex formation of the scPLA films. The stereocomplex crystallinities of the scPLA films increased as the PPG blend ratio increased, the PPG molecular weight decreased and the PDLA molecular weight decreased. The PPG blending significantly decreased the T _g and film transparency, and improved the elongation at break of the scPLA films. The results indicated that the PPG blending had an effect on the stereocomplexation and it improved the flexibility of the scPLA films.     

Physical organogels composed of amphiphilic block copolymers and 1,3:2,4-dibenzylidene-D-sorbitol

The 1,3:2,4-dibenzylidene-D-sorbitol (DBS) molecule is capable of self-organizing into nanoscale fibrils through intermolecular forces such as hydrogen bonding and pi interactions. At sufficiently high concentrations (typically less than approximately 2 wt%), the nanofibrils can form a network that promotes physical gelation of the matrix medium. Previous studies have investigated the mechanism of DBS-induced gelation and the features of DBS-containing gels in poly(ethylene glycol) (PEG) and poly(propylene glycol) (PPG). In this work, we examine the effect of adding DBS to a series of amphiphilic PPG-b-PEG-b-PPG triblock copolymers differing in composition and molecular weight. Dynamic rheological measurements reveal that the resultant gels are thermoreversible (i.e., they exhibit comparable mechanical properties before dissolution and after reformation under quiescent conditions), exhibiting a maximum in the elastic modulus (G') at temperatures near the gel dissolution (T(d)) and formation (T(f)) temperatures. Both T(d) and T(f) tend to increase with increasing DBS concentration and PPG content, and their difference decreases with increasing PPG fraction in the copolymer. The magnitude of G' is sensitive to copolymer composition and polymer identity at low DBS concentrations, but becomes polymer-independent as the DBS network saturates at concentrations in excess of approximately 1 wt%.     

Stabilization of nonaqueous foam with lamellar liquid crystal particles in diglycerol monolaurate/olive oil system

Nonaqueous foams stabilized by lamellar liquid crystal (L alpha) dispersion in diglycerol monolaurate (designated as C12G2)/olive oil systems are presented. Foamability and foam stability depending on composition and the effects of added water on the nonaqueous foaming behavior were systematically studied. It was found that the foamability increases with increasing C12G2 concentration from 1 to 3 wt% and then decreases with further increasing concentration, but the foam stability increases continuously with concentration. Depending on compositions, foams are stable for a few minutes to several hours. Foams produced by 10 wt% C12G2/olive oil system are stable for more than 6 h. In the study of effects of added water on the foaming properties of 5 wt% C12G2/olive oil system, it was found that the foamability and foam stability of 5 wt% C12G2/olive oil decreases upon addition of 1 wt% water, but with further increasing water, both the foamability and foam stability increase. Foams with 10% water added system are stable for approximately 4 h. Phase behavior study of the C12G2 in olive oil has shown the dispersion of L alpha particles in the dilute regions at 25 degrees C. Thus, stable foams in the C12G2/olive oil system can be attributed to L alpha particle, which adsorb at the gas-liquid interface as confirmed by surface tension measurements and optical microscopy. Laser diffraction particle size analyzer has shown that the average particle diameter decreases with increasing the C12G2 concentration and, hence, the foams are more stable at higher surfactant concentration. Judging from foaming test, optical micrographs, and particle size, it can be concluded that stable nonaqueous foams in the studied systems are mainly caused by the dispersion of L alpha particles and depending on the particle size the foam stability largely differs.     

Structural effects on polyether cationization by alkali metal ions in matrix-assisted laser desorption/ionization

Structural effects on polyether cationization in matrix-assisted laser desorption/ionization (MALDI) are investigated using three different polyethers: PEG (polyethylene glycol), PPG (polypropylene glycol), and PTHF (polytetrahydrofuran). This study was performed using equimolar cesium and lithium chlorides as the cationizing agent. It was observed that the polyether structure variation led to a substantial change in polyether selectivity for alkali metal ion complexation. Moreover, it was found that like PEG, PPG displays a different selectivity for Cs⁺ and Li⁺ with different matrices. Discussion of these results and their implication in MALDI are given.     

Shape memory polyurethanes based on recycled polyvinyl butyral. I. Synthesis and morphology

Shape memory polyurethanes (SMPUs) were synthesized by 4,4′-diphenylmethane diisocyanate (MDI), hexane-1,6-diol (HD), polypropylene glycol (PPG), and recycled polyvinyl butyral (PVB). Dynamic mechanical analysis, differential scanning calorimetry and Fourier transformation infrared attenuated total reflection spectroscopy was used to characterize the poly (vinylbutyral-urethanes). Micro-phase domain separation of hard and soft segments and phase inversion were investigated. Increasing the hard segment content, i.e., average hard segment molecular weight, leads to an increase in the degree of micro-phase separation, hard domain order and crystallinity. The crystalline hard segment structures combined with the elastic nature of soft segment matrix provide enough physical and chemical crosslinks to have shape memory effect.