磁流变体的制备及性能

对以羰基铁粉、硅油和烃类油为悬浮相和悬浮介质,通过适当添加剂和工艺制备的磁流变体材料,制备方法、磁流变性能及影响因素进行了研究,认为是具有良好综合性能的磁流变体材料。制备的磁流变体具有较低的零场粘度（0．4－1．5Pas),较高的剪切应力（τ=50-75kPa)和良好的稳定性及阻尼性能。     

Radiation Vulcanization of Magnetorheological Elastomers Based on Silicone Rubber

介绍了两种制备磁流变弹性体的硫化方法即高温硫化和辐射硫化. 研究中采用动态力学分析仪(DMA)测量了样品的动态力学特性.特别是对样品的磁流变效应和耐久性进行了详细的测试. 实验结果表明,经过辐射硫化的样品具有更大的零场模量和磁致模量,以及更好的磁流变效应和耐久性. 为了解释这些结果,文章对样品的体积形变和增塑剂渗出都作了详细的分析. 在硫化过程中样品的体积保持稳定是辐射硫化样品具有大磁致模量的重要原因,而增塑剂渗透性小也是辐射硫化样品具有高磁流变效应和耐久性的重要因素.     

Kerr介质中V型三能级原子与双模奇偶纠缠相干光场相互作用的纠缠特性

运用量子约化熵研究了Kerr介质中V型三能级原子与双模奇偶纠缠相干光场相互作用系统中场熵的演化特性.分析了Kerr介质、失谐量和光场的初始平均光子数对场熵的影响.结果表明:Kerr介质与光场的耦合系数对场熵的振荡特性有调制作用,增大失谐量,场熵的最大值减小,振荡频率增大,由初始时刻的零值增大到最大值所需的时间也增大;光场的平均光子数太大或太小都不利于原子与光场之间的纠缠.     

轻质磁性材料的制备及在磁流变液中的应用

研究了使用化学镀的方法在轻质载体上包覆具有磁性的镍、钴等物质。该材料具有密度低的优点（有效密度为2-3g/cm^3）。对比于几种羰基镍粉制备的磁流变液的沉降稳定性,使用该轻质磁性材料制备的磁流变液不用加防沉剂,其稳定性类似于加入较多防沉剂的羟基镍粉磁流变液。其在磁场下表观粘度比零磁场下的粘度有几十倍的变化。因此,使用该轻质磁性材料有望解决磁流变液普遍存在的沉降问题,得到综合性能良好的产品。     

光学镜面磁流变确定性修形的实现

磁流变确定性修形具有高精度、高效率、高表面质量以及近零亚表面损伤的特点。介绍了磁流变修形技术的基本原理和方法,并对磁流变修形中涉及的关键技术进行了讨论。在自研的磁流变修形设备上采用水基磁流变抛光液对一块直径80mm的K9玻璃平面进行了磁流变修形实验。经过一次迭代修形(4.39min)使其面形精度峰谷(PV)误差由初始的0.144λ改善到0.06λ(λ=632.8nm),均方根(RMS)误差由初始的0.031λ改善到0.01λ,面形收敛率达到2.81,表面粗糙度RMS值达到0.345nm。实验结果表明,采用磁流变进行光学表面修形,面形收敛快,面形精度高,表面质量好,可广泛应用于高精度光学镜面加工。     

磁流变液构成的类梯度结构振动传递特性

提出了一种磁流变液构成的类梯度结构,并通过理论建模、数值计算和实验研究了该结构的振动传递特性.磁流变液在磁场作用下具有液固转换的特殊理化性质,而液固转换过程就是磁流变液的振动传递阻抗变化过程.因此,基于磁流变液的这一特性,通过控制磁场,构建了类梯度结构.基于弹性波传递的一维波动方程,建立了垂直入射的弹性波在类梯度结构中传递的波动方程.然后,使用连续介质的离散化方法和传递矩阵法进行求解,得到振级落差的表达式,对其进行数值计算,分析类梯度结构的振级落差随弹性波频率和磁场强度的变化趋势.最后,对类梯度结构的振动传递特性进行了实验研究,分析了磁场强度对类梯度结构振动传递特性的影响.研究结果表明,与均匀场作用的磁流变液相比,类梯度结构对弹性波的衰减效果更好,且该结构具备良好的可调控特性.     

Metamaterials电磁特性的数值仿真研究

利用HFSS软件，对电磁波在左手材料中的后向波传输、平板成像特性和近零折射率媒质的定向辐射特性进行了全波仿真研究，分别验证了左手材料与近零折射率媒质的上述特性。利用AnsoftDesigner软件，对去掉并联电感和去掉串联电容的、基于微带线的两种简化的左右手复合传输线构成的具有磁单负和电单负特性介质的电磁特性进行了仿真研究，验证了电磁波在匹配的MNG-ENG介质对结构的隧穿特性。     

碳化硅基底改性硅表面的磁流变抛光EI北大核心CSCD

为克服传统抛光方法在硅改性的碳化硅表面抛光存在的不足,采用磁流变抛光在精抛光阶段实现面形误差高效去除和快速收敛。基于实际应用中的对磁流变抛光液的需求,提出了磁流变液的性能要求,并配制了适合改性硅表面抛光的磁流变抛光液,检测所配制的抛光液体的流变特性和分散稳定性,证明了液体具有良好的性能。对口径为130 mm(有效口径为120 mm)的硅改性的同轴非球面碳化硅工件进行实际抛光。经过两个周期约3 h的抛光,面形误差均方根(RMS)从0.051λ(λ=632.8 nm)快速收敛至0.012λ,粗糙度Ra达0.618 nm。验证了所配制的磁流变抛光液满足碳化硅基底改性硅表面的抛光需求,证明了磁流变抛光技术在镜面硅改性后精抛光阶段具有独特的优势。     

碳化硅基底改性硅表面的磁流变抛光

为克服传统抛光方法在硅改性的碳化硅表面抛光存在的不足,采用磁流变抛光在精抛光阶段实现面形误差高效去除和快速收敛。基于实际应用中的对磁流变抛光液的需求,提出了磁流变液的性能要求,并配制了适合改性硅表面抛光的磁流变抛光液,检测所配制的抛光液体的流变特性和分散稳定性,证明了液体具有良好的性能。对口径为130 mm(有效口径为120 mm)的硅改性的同轴非球面碳化硅工件进行实际抛光。经过两个周期约3 h的抛光,面形误差均方根(RMS)从0.051λ(λ=632.8 nm)快速收敛至0.012λ,粗糙度Ra达0.618 nm。验证了所配制的磁流变抛光液满足碳化硅基底改性硅表面的抛光需求,证明了磁流变抛光技术在镜面硅改性后精抛光阶段具有独特的优势。     

永磁流变抛光纳米精度非球面技术研究

利用永磁流变抛光技术制造高精度光学元件是一项极具前景的超精密制造技术。对一台五轴联动磁流变数控抛光系统的结构特点、功能特色及关键部件的设计进行了阐述。在此基础上,结合装置开展基础试验,对磁流变抛光过程中的主要控制参量如抛光轮下压量、抛光轮速度等对材料去除特性的影响进行了研究。开展了磁流变抛光对提高工件(K9玻璃)表面粗糙度效果的抛光试验,结果证明该套系统具有良好的磁流变抛光特性,抛光23min后工件表面粗糙度降低到0 6739nm。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.