Efficient adsorption and photocatalytic degradation of Congo red onto hydrothermally synthesized NiS nanoparticles

The influence of the length of the cation alkyl chain on the dispersibility by ultrasonic treatment of TiO₂ nanopowders in hydrophilic imidazolium-based room temperature ionic liquids was studied for the first time by dynamic light scattering and advanced rheology. TiO₂ nanopowders had been synthesized by chemical vapor synthesis (CVS) under varied conditions leading to two different materials. A commercial nanopowder had been used for comparison. Characterizations had been done using transmission electron microscopy, X-ray diffraction, nitrogen adsorption with BET analysis, and FT-IR spectroscopy. Primary particle sizes were about 6 and 8 nm for the CVS-based and 26 nm for the commercial materials. The particle size distribution in the dispersion was strongly influenced by the length of the cation alkyl chain for all the investigated powders with different structural characteristics and concentrations in the dispersion. It was found that an increase of the alkyl chain length was beneficial, leading to a narrowing of the particle size distribution and a decrease of the agglomerate size in dispersion. The smallest average nanoparticle sizes in dispersion were around 30 nm. Additionally, the surface functionality of the nanoparticles, the concentration of the solid material in the liquid, and the period of ultrasonic treatment control the dispersion quality, especially in the case of the ionic liquids with the shorter alkyl chain. The influence of the nanopowders characteristics on their dispersibility decreases considerably with increasing cation alkyl chain length. The results indicate that ionic liquids with adapted structure are candidates as absorber media for nanoparticles synthesized in gas phase processes to obtain liquid dispersions directly without redispergation.     

Influence of nano-SiO2 on dilational viscoelasticity of liquid/air interface of cetyltrimethyl ammonium bromide

An investigation was reported on the interfacial rheology of nano-SiO₂ dispersions in the presence of cetyltrimethyl ammonium bromide (CTAB). The interfacial dilational viscoelasticity had been measured as a function of the nano-particle concentration. The properties of the interface were affected by different processes such as the surfactants adsorption at the liquid or at the particle interfaces. It was found that the influence of nano-SiO₂ particles on the interfacial properties was evident and complex. The property of SiO₂ particles would change from hydrophilic to hydrophobic when CTAB molecules absorbed at their surface. The reorganization of surfactants and the participation of hydrophobic SiO₂ at the surface were offered to explain the process. In particular, the interaction between surfactants and particles, and the transfer of particles from bulk to the surface played an important role in changing the properties of the interface.     

Interleukin-12 plasmid DNA delivery using l-thyroxine-conjugated polyethylenimine nanocarriers

The influence of the hydrophilicity and length of the cation alkyl chain in imidazolium-based ionic liquids on the dispersability of ZnO nanoparticles by ultrasound treatment was studied by dynamic light scattering and advanced rheology. ZnO nanopowder synthesized by chemical vapor synthesis was used in parallel with one commercially available material. Before preparation of the dispersion, the nanoparticles characteristics were determined by transmission electron microscopy, X-ray diffraction, nitrogen adsorption with BET analysis, and FT-IR spectroscopy. Hydrophilic ionic liquids dispersed all studied nanopowders better and in the series of hydrophilic ionic liquids, an improvement of the dispersion quality with increasing length of the alkyl chain of the cation was observed. Especially, for ionic liquids with short alkyl chain, additional factors like nanoparticle concentration in the dispersion and the period of the ultrasonic treatment had significant influence on the dispersion quality. Additionally, nanopowder characteristics (crystallite shape and size as well as the agglomeration level) influenced the dispersion quality. The results indicate that the studied ionic liquids are promising candidates for absorber media at the end of the gas phase synthesis reactor allowing the direct preparation of non-agglomerated nanoparticle dispersions without supplementary addition of dispersants and stabilizers.     

Probing the adsorption of methylimidazole at ionic liquids/Cu electrode interface by surface‐enhanced Raman scattering spectroscopy

Two kinds of room‐temperature ionic liquids, 1‐butyl‐3‐methylimidazolium bromide ([BMIM]Br) and 1‐butyl‐3‐methylimidazolium tetrafluoroboride ([BMIM]BF₄), were used as solvent, and the adsorption of the ionic liquids themselves and of N‐methylimidazole (NMIM) were investigated by electrochemical surface‐enhanced Raman scattering (SERS) over a wide potential window. The results revealed that the cation of ionic liquid adsorbed onto Cu surface with different configurations in different potential ranges. When the potential was changed from the negative to the positive range, the orientation underwent a change from flat to vertical, and the onset potential for the orientation change was dependent on the types of anion of the ionic liquid. The ionic liquid in bulk solution exhibited a remarkable effect on the adsorption of NMIM. The electrode surface structure changed from adsorbing the ionic liquid at the negative potential to coadsorbing the ionic liquid and NMIM at relative positive potential for the [BMIM]BF₄ liquids, and formed films of NMIM at extremely positive potential. Due to the strong specific adsorption of Br⁻, the coadsorption of ionic liquid and NMIM was not observed in the system [BMIM]Br. By simulating the electrode surroundings, two surface complexes [Cu(NMIM)₄Br]Br·H₂O and [Cu(NMIM)₄](BF₄)₂ were synthesized by the electrochemical method in the corresponding ionic liquids for modeling the surface coordination chemistry of NMIM. The surface coordination configuration of NMIM and ionic liquids is proposed. Copyright © 2009 John Wiley & Sons, Ltd.     

Continuous production of inorganic magnetic nanocomposites for biomedical applications by laser pyrolysis

Magnetic composites of Fe-based nanoparticles encapsulated in carbon/silica (C/SiO₂@Fe) or carbon (C@Fe) matrices were prepared by laser-induced pyrolysis of aerosols. The powders were dispersed in aqueous solutions at pH 7 resulting in biocompatible colloidal dispersions with a high resistance to biodegradation. Structural and magnetic properties and the suitability of aqueous dispersions as contrast agent for MRI were analyzed. The results of these characterizations and the NMR relaxivity data are very encouraging for application of laser pyrolysis products in the field of living tissues.     

Microstructural analysis of liquid and amorphous SiO2 nanoparticles

Microstructural properties of liquid and amorphous SiO₂ nanoparticles have been investigated via molecular dynamics (MD) simulations with the interatomic potentials that have weak Coulomb interaction and Morse-type short-range interaction under non-periodic boundary conditions. Structural properties of spherical nanoparticles with different sizes of 2, 4 and 6 nm obtained at 3500 K have been studied through partial radial distribution functions (PRDFs), coordination number and bond-angle distributions, and compared with those observed in the bulk. The core and surface structures of liquid SiO₂ nanoparticles have been studied in detail. We found significant size effects on structure of nanoparticles. Calculations also show that if the size is larger than 4 nm, liquid SiO₂ nanoparticles at the temperature of 3500 K have a lightly distorted tetrahedral network structure with the mean coordination number Z_Si-O≈4.0 and Z_O-Si≈2.0 like those observed in the bulk. Moreover, temperature dependence of structural defects and SiO_x stoichiometry in nanoparticles on cooling from the melt has been found and presented.     

The Study of Aggregation Processes in Colloidal Solutions of Magnetite–Silica Nanoparticles by NMR Relaxometry,AFM, and UV–Vis-Spectroscopy

Colloidal solutions of magnetic nanoparticles were studied as a promising magnetic resonance imaging (MRI) contrast agent. The problem of aggregative stability of solutions is considered. Sol-gel synthesis of magnetite colloidal solutions stabilized by silica is described. Transmittance spectra were measured to analyze sedimentation of nanoparticles in magnetite–silica solutions of different compositions and concentrations. It is shown that the synthesized nanoparticles can be used as MRI contrast agents. The surface morphology and particle size of Fe₃O₄/SiO₂ layers were estimated by atomic force mictroscopy (AFM) technique. The mechanism of magnetic-field-induced aggregation of Fe₃O₄/SiO₂ nanoparticles into chain-like and fractal structures is described.     

Femtosecond laser writing of nanostructures on bulk Al via its ablation in air and liquids

We report on the formation of self-organized nanostructures (NS) on bulk Al under its ablation in air and liquids with femtoseconds (fs) laser pulses. In case of exposure into liquids, NS are regularly formed on the Al surface with an average period of about 200 nm, independent of the laser polarization. A dispersion of Al nanoparticles (NPs) into the liquid additionally occurs. Irregular nano-bumps are produced when the irradiation is performed in air. NP dispersions as well as NS formed on Al surface show a characteristic absorption peak in the near UV which has been attributed to plasmon oscillation of electrons. The wings of this peak extending to the visible, lead to a distinct yellow coloration of the processed Al surface and the liquid dispersions. Ultrafast laser processing of bulk Al in liquids may be potentially a promising technique for efficient production of nanosized aluminum.     

Synthesis, characterization, and in vitro release of diclofenac sodium from hybrid nanostructured magnetite–calcium pectinate

CdS nanoparticles were prepared by reacting CdCl₂ and Na₂S in different microemulsions and several micellar media comprising combinations of ionic liquid, ionic, nonionic, zwitterionic amphiphiles, isopropyl alcohol, and isopropylmyristate as templates. This simple chemical method was found to be effective in the preparation of CdS dispersions mostly in the range of 3?C8?nm with moderate polydispersity. The dispersions were characterized by taking UV?CVis and fluorescence spectra as well as by DLS, EDX, SEM, and TEM methods. Globular, sharp-edged elongated flake-like, and wire type morphologies were witnessed by SEM. TEM results evidenced spherical nanoentities. The dispersions witnessed both fairly and weakly semiconducting varieties; insulator-type dispersions were also observed. They have shown characteristic fluorescence properties. The nanodispersions evidenced biocidal activities toward both gram-positive and gram-negative bacteria.     

Acoustic cavitation in 1-butyl-3-methylimidazolium bis(triflluoromethyl-sulfonyl)imide based ionic liquid

In this work, a comparison between the temperatures/pressures within acoustic cavitation bubble in an imidazolium-based room-temperature ionic liquid (RTIL), 1-butyl-3-methylimidazolium bis(triflluoromethyl-sulfonyl)imide ([BMIM][NTf₂]), and in water has been made for a wide range of cavitation parameters including frequency (140–1000 kHz), acoustic intensity (0.5–1 W cm⁻²), liquid temperature (20–50 °C) and external static pressure (0.7–1.5 atm). The used cavitation model takes into account the liquid compressibility as well as the surface tension and the viscosity of the medium. It was found that the bubble temperatures and pressures were always much higher in the ionic liquid compared to those predicted in water. The valuable effect of [BMIM][NTf₂] on the bubble temperature was more pronounced at higher acoustic intensity and liquid temperature and lower frequency and external static pressure. However, confrontation between the predicted and the experimental estimated temperatures in ionic liquids showed an opposite trend as the temperatures measured in some pure ionic liquids are of the same order as those observed in water. The injection of liquid droplets into cavitation bubbles, the pyrolysis of ionic liquids at the bubble-solution interface as well as the lower number of collapsing bubbles in the ionic liquid may be the responsible for the lower measured bubble temperatures in ionic liquids, as compared with water.     

Preparation of superhydrophobic poly(methyl methacrylate)-silicon dioxide nanocomposite films

Superhydrophobic poly(methyl methacrylate)-SiO₂ (coded as PMMA-SiO₂) nanocomposite films with micro-nanohierarchical structure were prepared via a simple approach in the absence of low surface-energy compounds. By spin-coating the suspension of hydrophobic silica (SiO₂) nanoparticles dispersed in PMMA solution, target nanocomposite films were obtained on glass slides. The wetting behavior of PMMA-SiO₂ nanocomposite films was investigated in relation to the dosage of SiO₂ nanoparticles dispersed in PMMA solution. It was found that hydrophilic PMMA film was transferred to superhydrophobic PMMA-SiO₂ nanocomposite films when hydrophobic SiO₂ nanoparticles were introduced into the PMMA solution at a high enough dosage (0.2 g and above). Resultant PMMA-SiO₂ nanocomposite films had a static water contact angle of above 162°, showing promising applications in selfcleaning and waterproof for outer wall of building, outer covering for automobile, sanitary wares, and so forth.     

A versatile method for the preparation of end-functional polymers onto SiO2 nanoparticles by a combination of surface-initiated ATRP and Huisgen [3 + 2] cycloaddition

A versatile method was developed for the chain-end functionalization of the grafted polymer chains for surface modification of nanoparticles with functionalized groups through a combination of surface-initiated atom-transfer radical polymerization (ATRP) and Huisgen [3 + 2] cycloaddition. First, the surface of SiO₂ nanoparticles was modified with poly(methyl methacrylate) (PMMA) brushes via the “grafting from” approach. The terminal bromides of PMMA-grafted SiO₂ nanoparticles were then transformed into an azide function by nucleophilic substitution. These azido-terminated PMMA brushes on the nanoparticle surface were reacted with alkyne-terminated functional end group via Huisgen [3 + 2] cycloaddition. FTIR and ¹H NMR spectra indicated quantitative transformation of the chain ends of PMMA brushes onto SiO₂ nanoparticles into the desired functional group. And, the dispersibility of the end-functional polymer-grafted SiO₂ nanoparticles was investigated with a transmission electron microscope (TEM).     

Characteristics of silicon oxide thin films prepared by sol electrophoretic deposition method using tetraethylorthosilicate as the precursor

Silicon dioxide films were prepared on p-type Si (1 0 0) substrates by sol electrophoretic deposition (EPD) using tetraethylorthosilicate (TEOS) at low temperature. According to the variation of sol dipping conditions, we estimated the characteristics of SiO₂ films, such as composition, surface morphology, wet etch rate, breakdown voltage, etc. The growth rate of the film increased linearly with increasing TEOS quantity in solution. It increased exponentially with the increase in deposition time, and the film thickness was saturated at approximately 200 nm on hydrophilic Si surface after more than 6 days. The growth rate of the EPD SiO₂ films on the hydrophobic Si surface was much lower than that of the film on the hydrophilic Si surface.     

Fullerenes in molecular liquids. Solutions in “good” solvents: Another view

Brief review and update information concerning the state of “bare” (unmodified) fullerenes in different solvents, including organosols and hydrosols, is given. The hydrophobic nature of fullerene dispersions in aqueous media is discussed. The possibility of the existence of thermodynamic equilibrium in (fullerene + non-polar solvent) system is questioned. The modern data allow returning to the consideration of C₆₀ (C₇₀, etc.) molecules as colloidal (or sub-colloidal) species, inclined to aggregation. Recent publications support the idea of the solvophobic solvation of fullerene molecules even in “good” solvents. Hence, the solvophobic effect, in concert with the van-der-Waals attraction, seems to be driving forces of permanent (though sometimes very slow) aggregate formation, analogous to coagulation of nano-sized particles of common solvophobic colloidal systems.     

Improved performances on surface‐enhanced Raman scattering based on electrochemically roughened gold substrates modified with SiO2 nanoparticles

In this work, we use electrochemical oxidation–reduction cycles (ORC) methods to prepare surface‐enhanced Raman scattering (SERS)‐active gold substrates modified with SiO₂ nanoparticles to improve the corresponding SERS performances. Based on the modified substrates, the SERS of Rhodamine 6G (R6G) exhibits a higher intensity by 3‐fold of magnitude, as compared with that of R6G adsorbed on a SERS‐active Au substrate without the modification of SiO₂ nanoparticles. Moreover, the SERS enhancement capabilities of the modified and the unmodified Au substrates are seriously destroyed at temperatures higher than 250 and 200 °C, respectively. These results indicate that the modification of SiO₂ nanoparticles can improve the thermal stability of SERS‐active substrates. The aging in SERS intensity is also depressed on this modified Au substrate due to the contribution of SiO₂ nanoparticles to SERS effects. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation of luminescent ZnS:Cu nanoparticles for the functionalization of transparent acrylate polymers

Highly luminescent ZnS:Cu nanoparticles were synthesized in a coprecipitation route using aqueous salt solutions and thiopropionic acid as stabilizer. The method yields a stable, transparent particle dispersion in water and allows for a good control over particle size in the range of 3-10 nm as determined by dynamic light scattering, small angle X-ray scattering and transmission electron microscopy. Strong luminescence of the nanoparticles was observed under UV-excitation and emission colors could be adjusted in the range of blue to green by varying the Cu-doping concentration. The phase transfer of the ZnS:Cu nanoparticles into non-polar solvents using octylamine was used for a hydrophobic surface functionalization. The hydrophobic particles were used for the fabrication of transparent bulk nanocomposites via in situ-polymerization of dispersions in laurylacrylate. A high transparency of the composite materials, and the luminescence of the ZnS:Cu nanoparticles is retained during the phase transfer and the polymerization process allowing for the integration of a new luminescent functionality into the polymer material.     

The Synthesis of Magnetic and Fluorescent Bi-functional Silica Composite Nanoparticles via Reverse Microemulsion Method

In this paper, a simple synthesis method of small-size( about 50 nm in diameter), high magnetic and fluorescent bi-functional silica composite nanoparticles were developed, in which water-soluble Fe₃O₄ magnetic nanoparticlels (MNs) and CdTe quantum dots (QDs) were directly incorporated into a silica shell by reverse microemulsion method. The high luminescent QDs can be used as luminescent marker, while the high magnetic MNs allow the manipulation of the bi-functional silica composite nanoparticles by external magnetic field. Poly (dimethyldiallyl ammonium chloride) was used to balance the electrostatic repulsion between CdTe QDs and silica intermediates to enhance the fluorescence intensity of MNs-QDs/SiO₂ composite nanoparticles. The optical property, magnetic property, size characterization of the bi-functional composite nanoparticles were studied by UV-Vis and PL emission spectra, VSM, TEM, SEM. The stabilities toward time, pH and ionic strength and the effect of MNs on the fluorescence properties of bi-functional silica composite nanoparticles were also studied in detail. By modifying the surface of MNs-QDs/SiO₂ composite nanoparticles with amino and methylphosphonate groups, biologically functionalized and monodisperse MNs-QDs/SiO₂composite nanoparticles can be obtained. In this work, bi-functional composite nanoparticles were conjugated with FITC labeled goat anti-rabbit IgG, to generate novel fluorescent-magnetic-biotargeting tri-functional composite nanoparticles, which can be used in a number of biomedical application.     

Experimental study on the coalescence process of SiO2 supported colloidal Au nanoparticles

We report on an experimental study of the coalescence-driven grow process of colloidal Au nanoparticles on SiO₂ surface. Nanoparticles with 30, 50, 80, 100 nm nominal diameters on a SiO₂ substrate were deposited, from solutions, by the drop-casting method. Then, annealing processes, in the 573–1173 K temperature range and 900–3600 s time range, were performed. Using scanning electron microscopy analyses, the temporal evolution of the nanoparticles sizes has been studied. In particular, for all classes of nanoparticles, the experimental-obtained diameters distributions evidenced double-peak shapes (i. e. bimodal distributions): a first peak centered (and unchanged changing the annealing temperature and/or time) at the nominal diameter of the as-deposited nanoparticles, 〈D₀〉, and a second peak shifting at higher mean diameters, 〈D_C〉, increasing the annealing temperature and/or time. This observation suggested us a coalescence-driven growth process of a nanoparticles sub-population. As a consequence, the temporal evolution of 〈D_C〉 (for each class of nanoparticles and each annealing temperature), within the well-established particles coalescence theoretical framework, has been analyzed. In particular, by the analyses of the experimental data using relations as prescribed by the theoretical model, a characteristic size-dependent activation energy for the Au nanoparticles coalescence process has been evaluated.     

Multifunctional TiO2‐Based Particles: The Effect of Fluorination Degree and Liquid Surface Tension on Wetting Behavior

A systematic investigation into the influence of the degree of fluorination on the static and dynamic wetting behavior of TiO₂‐based nanobelt (TNB) particles with various liquids is described. The effect of the degree of fluorination and the surface tension of the liquid on the occurrence and stability of liquid marbles, foams or dispersions are studied and the wetting behavior and arrangement of particles at the air–liquid surface are observed. Using contact angle (θ) measurements, the relation between the type of particle‐stabilized material and θ is established. For liquids of relatively high tension like water or formamide which do not wet the fluorinated particles, a powder‐like material (marble) is formed. For polar oils of intermediate tension (35–50 mN m^?1), which partially wet the fluorinated particles, stable air‐in‐oil foams can be prepared in which particles form a close‐packed layer enveloping air bubbles. Liquids of relatively low tension, e.g., ethanol or polydimethylsiloxane, wet the particles forming a uniform dispersion and partial sedimentation. By contrast, the as‐prepared hydrophilic TNB particles are rapidly wetted by all the liquids as expected due to their high surface energy. The stable cross‐stacked TNB particles with fluoroalkylsilane (FAS) modification could be a versatile platform in a wide range of applications, especially for fluidic devices (e.g., biofluids, gas sensing, and lab‐on‐a‐chip devices). In a proof‐of‐concept study, the oil–water separation performance of fabrics with chemically stable TNB/FAS coating and the liquid isolation by a TNB/FAS shell for highly sensitive gas sensing or reagent assays are investigated.