In-situ visualization of a super-accelerated synthesis of zinc oxide nanostructures through CO2 laser heating

A simple growth technique capable of growing a variety of zinc oxide (ZnO) nanostructures with record growth rates of 25 μm/s is demonstrated. Visible lengths of ZnO nanowires, nanotubes, comb-like and pencil-like nanostructures could be grown by employing a focused CO₂ laser-assisted heating of a sintered ZnO rod in ambient air, in few seconds. For the first time, the growth process of nanowires was videographed, in-situ, on an optical microscope. It showed that ZnO was evaporated and presumably decomposed into Zn and oxygen by laser heating, reforming ZnO nanostructures at places with suitable growth temperatures. Analysis on the representative nanowires shows a rectangular cross-section, with a [0 0 0 1] growth direction. With CO₂ laser heating replacing furnace heating used conventionally, and using different reactants and forming gases, this method could be easily adopted for other semiconducting inorganic nanostructures in addition to ZnO.     

The influences of O/Zn ratio and growth temperature on carbon impurity incorporation in ZnO grown by metal-organic chemical vapor deposition

The strong correlations between the O/Zn ratio and carbon impurity incorporation have been observed on the ZnO films grown using N₂O or O₂ as oxygen source in metal-organic chemical vapor deposition (MOCVD). From in-situ mass spectrometric measurements, the O/Zn ratio in the MOCVD reactor is found to decrease to a minimum value as the growth temperature increased till a critical growth temperature T_c, and then increased above T_c due to different dissociation rates of the oxygen and Zn sources. The strongest D and G modes, which are ascribed to carbon clusters sp² related modes, have been observed in Raman scattering spectroscopy for the ZnO samples grown at T_c, indicating the highest incorporation rate of carbon impurity in the samples grown at T_c. Compared with O₂, N₂O has a low dissociation rate and that leads to a lower value of O/Zn ratio, resulting in much stronger D and G modes and higher incorporation rate of carbon impurities in the samples grown at T_c. It is interesting to note that the lowest specific resistances from Hall effect measurements were also obtained on the samples grown at T_c, indicating possible electrical contributions from the formation of carbon clusters, which should be highly conductive regions in ZnO. Furthermore, ionization or addition of H₂ in the case of N₂O can significantly enhance the dissociation of N₂O, with film quality improved significantly. This study shows that a high O/Zn ratio is critical to suppress carbon impurity incorporation and to grow high quality ZnO by MOCVD, especially at low growth temperature.     

Suppression of phase separation in InGaN layers grown on lattice-matched ZnO substrates

Sapphire and SiC are typical substrates used for GaN growth. However, they are non-native substrates and result in highly defective materials. The use of ZnO substrates can result in perfect lattice-matched conditions for 22% indium InGaN layers, which have been found to suppress phase separation compared to the same growths on sapphire. InGaN layers were grown on standard (0 0 0 2) GaN template/sapphire and (0 0 0 1) ZnO substrates by metalorganic chemical vapor deposition. These two substrates exhibited two distinct states of strain relaxation, which have direct effects on phase separation. InGaN with 32% indium exhibited phase separation when grown on sapphire. Sapphire samples were compared with corresponding growths on ZnO, which showed no evidence of phase separation with indium content as high as 43%. Additional studies in Si-doping of InGaN films also strongly induced phase separation in the films on sapphire compared with those on ZnO. High-resolution transmission electron microscopy results showed perfectly matched crystals at the GaN buffer/ZnO interface. This implied that InGaN with high indium content may stay completely strained on a thin GaN buffer. This method of lattice matching InGaN on ZnO offers a new approach to grow efficient emitters.     

Properties of ZnO films grown on (0 0 0 1) sapphire substrate using H2O and N2O as O precursors by atmospheric pressure MOCVD

In this paper, we compare the properties of ZnO thin films (0 0 0 1) sapphire substrate using diethylzinc (DEZn) as the Zn precursor and deionized water (H₂O) and nitrous oxide (N₂O) as the O precursors, respectively in the main ZnO layer growth by atmospheric pressure metal–organic chemical vapor deposition (AP-MOCVD) technique. Surface morphology studied by atomic force microscopy (AFM) showed that the N₂O-grown ZnO film had a hexagonal columnar structure with about 8 μm grain diameter and the relatively rougher surface compared to that of H₂O-grown ZnO film. The full-widths at half-maximum (FWHMs) of the (0 0 0 2) and () ω-rocking curves of the N₂O-grown ZnO film by double-crystal X-ray diffractometry (DCXRD) measurement were 260 and 350 arcsec, respectively, indicating the smaller mosaicity and lower dislocation density of the film compared to H₂O-grown ZnO film. Compared to H₂O-grown ZnO film, the free exciton A (FX_A) and its three phonon replicas could be clearly observed, the donor-bound exciton A⁰X (I₁₀):3.353 eV dominated the 10 K photoluminescence (PL) spectrum of N₂O-grown ZnO film and the hydrogen-related donor-bound exciton D⁰X (I₄):3.363 eV was disappeared. The electron mobility (80 cm²/V s) of N₂O-grown ZnO film has been significantly improved by room temperature Hall measurement compared to that of H₂O-grown ZnO film.     

Effects of growth temperature on the properties of ZnO/GaAs prepared by metalorganic chemical vapor deposition

A series of ZnO films were grown on GaAs(0 0 1) substrates at different growth temperatures in the range 250–720°C by metalorganic chemical vapor depostion. Field emission scanning electron microscopy was utilized to investigate the surface morphology of ZnO films. The crystallinity of ZnO films was investigated by the double-crystal X-ray diffractometry. The optical and electrical properties of ZnO films were also investigated using room-temperature photoluminescence and Hall measurements. Arrhenius plots of the growth rate versus reciprocal temperature revealed the kinetically limited growth behavior depending on the growth temperature. It was found that the surface morphology, structural, optical and electrical properties of the films were improved with increasing growth temperature to 650°C. All the properties of the film grown at 720°C were degraded due to the decomposition of ZnO film.     

Local structural,magnetic, and optical properties of Zn1−xFexO thin films

High quality Zn_1−xFe_xO thin films were deposited on α-sapphire$\alpha \text{-sapphire}$ substrates by RF magnetron sputtering. X-ray absorption fine structure measurements showed that the chemical valence of Fe ions in the films was a mixture of 2+ and 3+ states, and Fe ions substituted mainly for the Zn sites in the films. DC-magnetization measurements revealed ferromagnetic properties from 5 to 300 K. The photoluminescence measurements at 15 K showed a sharp main transition peak at 3.35 eV along with a broad impurity peak at 2.45 eV. The structural and magnetization analyses of the Zn_1−xFe_xO films strongly suggested that the ferromagnetism was the intrinsic properties of the films.     

Effect of grain size on the electrical properties of ultraviolet photodetector with ZnO/diamond film structure

Highly c-axis-oriented ZnO films were successfully deposited on the nucleation sides of freestanding diamond films by RF reactive magnetron sputtering. I–V characteristics of ultraviolet (UV) photodetectors with ZnO/diamond structure were studied and a significant photoresponse was observed under UV light illumination. The dark-current and the photocurrent of the ZnO photodetectors were relative to the grain size and the quality of ZnO films. For the photodetector with a bigger grain size, a weaker dark current and a stronger photocurrent were obtained under 10 V bias voltage. The photocurrent rise and decay process confirmed the carrier-trapping effect.     

SIMS and Raman characterizations of ZnO:N thin films grown by MOCVD

Nitrogen was incorporated into ZnO films grown by metalorganic chemical vapour deposition (MOCVD) on ZnO substrates using DMZn-TEN, tert-butanol and diallylamine, respectively, as zinc, oxygen and doping sources. The carrier gas was either hydrogen or nitrogen and the partial pressure ratio (R_VI/II) was varied in order to favor the nitrogen incorporation and/or reduce carbon related defects. The ZnO films have been characterized by Micro-Raman scattering and SIMS measurements. SIMS measurements confirm the nitrogen incorporation with concentrations extending from ∼10¹⁹ cm⁻³ to ∼4×10²⁰ cm⁻³. Raman spectra show nitrogen local vibration modes in films grown at low R_VI/II ratio and using H₂ as carrier gas. However, a vibration band attributed to carbon clusters dominates the Raman spectra for films grown with N₂ carrier. The contribution of N complexes was discussed. The strain was calculated for the as-grown and annealed films and it changes from tensile to compressive after annealing.     

Nanocrystalline Pr-doped ZnO insulator for metal–insulator–Si Schottky diodes

Pr-doped ZnO (ZnO:Pr) insulating thin films were prepared on glass and Si substrates by oxidation in air. The films were characterised by X-ray diffraction (XRD), energy dispersion X-ray fluorescence (EDXRF), and optical absorption spectroscopy. The molar ratio Pr/Zn of the samples was determined by the EDXRF method. The XRD study shows the formation of nanocrystalline (26–50 nm) nc-Pr-doped ZnO. The optical and electrical conduction were explained by a slight change of stoichiometric composition. The nc-ZnO:Pr/Si heterojunctions are being Schottky barrier diodes (SBDs) and exhibited high rectification behaviour. The parameters describe the current pass through those SBDs were determined according to the available models.     

Preparation and characterization of fiber-textured SrAl2O4:Eu films grown using a homo-buffer layer

This paper describes the preparation and characterization of fiber-textured SrAl₂O₄:Eu films on a quartz glass substrate using a homo-buffer layer. The effect of the buffer layer on the crystallinity and adhesion was investigated by cross-section transmission electron microscopy and X-ray diffraction (XRD). The results show that the prepared film was not only well crystallized but also highly textured. The preferred orientation of this textured film was confirmed to be (0 3 1) by pole figure measurement. In addition, this film exhibits excellent optical transparency, with an average transmittance of more than 80% in the visible range.     

Solvothermal growth of ZnO

The growth of ZnO single crystals and crystalline films by solvothermal techniques is reviewed. Largest ZnO crystals of 3 inch in diameter are grown by a high-pressure medium-temperature hydrothermal process employing alkaline-metal mineralizer for solubility enhancement. Structural, thermal, optical and electrical properties, impurities and annealing effects as well as machining are discussed. Poly- and single-crystalline ZnO films are fabricated from aqueous and non-aqueous solutions on a variety of substrates like glass, (100) silicon, -Al₂O₃, Mg₂AlO₄, ScAlMgO₄, ZnO and even some plastics at temperatures as low as 50 °C and ambient air conditions. Film thickness from a few nanometers up to some tens of micrometers is achieved. Lateral epitaxial overgrowth of thick ZnO films on Mg₂AlO₄ from aqueous solution at 90 °C was recently developed. The best crystallinity with a full-width half-maximum from the (0002) reflection of 26 arcsec has been obtained by liquid phase epitaxy employing alkaline-metal chlorides as solvent. Doping behavior (Cu, Ga, In, Ge) and the formation of solid solutions with MgO and CdO are reported. Photoluminescence and radioluminescence are discussed.     

Zinc oxide quantum dots embedded films by metal organic chemical vapor deposition

Zinc oxide (ZnO) quantum dots (QDs) were fabricated on silicon substrates by metal organic chemical vapor deposition. Formation of QDs is due to the vigorous reaction of the precursors when a large amount of precursors was introduced during the growth. The size of the QDs ranged from 3 to 12 nm, which was estimated by high-resolution transmission electron microscopy. The photoluminescence measured at 80 K showed that the emission of QDs embedded film ranged from 3.0 to 3.6 eV. The broad near-band-edge emission was due to the quantum confinement effect of the QDs.     

Decisive role of Au layer on the oriented growth of ZnO nanorod arrays via a simple aqueous solution method

Vertically aligned arrays of ZnO nanorod were synthesized on the Au/SiO₂/Si(1 0 0) substrate by a simple aqueous solution growth process, without pre-prepared ZnO seed layer. For comparison, glass and SiO₂/Si were also used as substrates, and the results show that the Au layer plays a decisive role in orienting the growth of the ZnO nanorod. The effects of other growth parameters, including Zn²⁺ concentration and growth time, on morphology, density, and orientation of the ZnO nanostructure were also studied and with longer reaction time, a new structure namely ZnO nanotip was obtained. Moreover, the growth mechanism of ZnO nanorod arrays grown on the Au/SiO₂/Si substrate was proposed.     

Heteroepitaxial growth of Cu2O thin film on ZnO by metal organic chemical vapor deposition

Cuprous oxide (Cu₂O) thin films were grown epitaxially on c-axis-oriented polycrystalline zinc oxide (ZnO) thin films by low-pressure metal organic chemical vapor deposition (MOCVD) from Copper(II) hexafluoroacetylacetonate [Cu(C₅HF₆O₂)₂] at various substrate temperatures, between 250 and 400 °C, and pressures, between 0.6 and 2.1 Torr. Polycrystalline thin films of Cu₂O grow as single phase with [1 1 0] axis aligned perpendicular to the ZnO surface and with in-plane rotational alignment due to (2 2 0)_Cu2O(0 0 0 2)_ZnO; [0 0 1]_Cu2O[1 2¯ 1 0]_ZnO epitaxy. The resulting interface is rectifying and may be suitable for oxide-based p–n junction solar cells or diodes.     

Vapour phase growth of epitaxial silicon carbide layers

After a brief overview of different epitaxial layer growth techniques, the homoepitaxial chemical vapour deposition (CVD) of SiC with a focus on hot-wall CVD is reviewed. Step-controlled epitaxy and site competition epitaxy have been utilized to grow polytype stable layers more than 50 μm in thickness and of high purity and crystalline perfection for power devices. The influence of growth parameters including gas flow, C/Si ratio, growth temperature and pressure on growth rate and layer uniformity in thickness and doping are discussed. Background doping levels as low as 10¹⁴ cm⁻³ have been achieved as well as layers doped over a wide n-type (nitrogen) and p-type (aluminium) range.

Furthermore the status of numerical process simulation is mentioned and SiC substrate preparation is described. In order to get flat and damage free epi-ready surfaces, they are prepared by different methods and characterised by atomic force microscopy and by scanning electron microscope using channelling patterns. For the investigation of defects in SiC high purity CVD layers are grown. The improvement of the quality of bulk crystal substrates by micropipe healing and so-called dislocation stop layers can further decrease the defect density and thus increase the yield and performance of devices. Due to its high growth rate functionality and scope for the use of multi-wafer equipment hot-wall CVD has become a well-established method in SiC-technology and has therefore great industrial potential.     

Analysis of the growth of RF sputtered ZnO thin films using the optical reflective second harmonic generation

Reflective second harmonic generation (RSHG) is used to analyze the growth condition of poly crystal zinc oxide (ZnO) film with a c-axis orientation, grown on the Si substrate by RF magnetron sputtering technique. It elucidates physical phenomena exhibited by growing ZnO thin films. Connecting with analytical results of the characteristic parameters derived from the X-ray patterns and SEM images, the relationship between the RSHG intensity and the substrate temperature reveals that the effect of the grain boundaries is the domination of the RSHG mechanism. The inclined structures of ZnO films on the Si substrate are explained with reference to these RSHG patterns.     

Fabrication of Zn/ZnO nanocables through thermal oxidation of Zn nanowires grown by RF magnetron sputtering

Fabrication of Zn/ZnO nanocables by thermal oxidation of Zn nanowires grown by RF magnetron sputtering is reported. Single crystalline Zn nanowires could be grown by controlling supersaturation of source material through the adjustment of temperature and Zn RF power. X-ray diffraction and high-resolution transmission electron microscopy showed that surfaces of these Zn nanowires, grown along the [0 1 0] direction, gradually oxidized inward the Zn core to form coaxial Zn/ZnO nanocables in the subsequent oxidation at 200 °C. In the Zn/ZnO nanocable, epitaxial relations of [1 0 0]_Zn//[1 0 0]_ZnO, and (0 0 1)_Zn//(0 0 1)_ZnO existed at the interface between the Zn core and ZnO shell. A number of dislocations were also observed in the interface region of the Zn/ZnO nanocable, which are attributed to large differences in the lattice constants of Zn and ZnO. With further increasing the oxidation temperature over 400 °C, Zn nanowires were completely oxidized to form polycrystalline ZnO nanowires. The results in this study suggest that coaxial Zn/ZnO nanocable can be fabricated through controlled thermal oxidation of Zn nanowires, yielding various cross-sectional areal fractions of Zn core and ZnO shell.     

Hydrothermal growth of ZnO nanorods on a-plane GaN/sapphire template

ZnO nanorod arrays are grown on a-plane GaN template/r-plane sapphire substrates by hydrothermal technique. Aqueous solutions of zinc nitrate hexahydrate and hexamethylenetetramine were employed as growth precursors. Electron microscopy and X-ray diffraction measurements were carried out for morphology, phase and growth orientation analysis. Single crystalline nanorods were found to have off-normal growth and showed well-defined in-plane epitaxial relationship with the GaN template. The 〈0 0 0 1〉 axis of the ZnO nanorods were observed to be parallel to the 〈1 0 1¯ 0〉 of the a-plane GaN layer. Optical property of the as-grown ZnO nanorods was analyzed by room temperature photoluminescence measurements.