MOCVD growth and optical properties of non-polar (1 1–2 0) a-plane GaN on (1 0–1 2) r-plane sapphire substrate

Non-polar a-plane GaN film with crystalline quality and anisotropy improvement is grown by use of high temperature AlN/AlGaN buffer, which is directly deposited on r-plane sapphire by pulse flows. Compared to the a-plane GaN grown on AlN buffer, X-ray rocking curve analysis reveals a remarkable reduction in the full width at half maximum, both on-axis and off-axis. Atomic force microscopy image exhibits a fully coalesced pit-free surface morphology with low root-mean-square roughness (∼1.5 nm). Photoluminescence is carried out on the a-plane GaN grown on r-plane sapphire. It is found that, at low temperature, the dominant emission at ∼3.42 eV is composed of two separate peaks with different characteristics, which provide explanations for the controversial attributions of this peak in previous studies.     

Effects of initial stages on the crystal quality of nonpolar a-plane AlN on r-plane sapphire by low-pressure HVPE

A 4–6 μm thick a-plane (1 1 2¯ 0) AlN was grown on r-plane sapphire substrate by low-pressure hydride vapor phase epitaxy (LP-HVPE), using a direct growth without any nitridation and buffer layer, a single-step nitridation growth, a two-step nitridation growth and a two-step buffer growth method. For the two-step buffer growth procedure, smoother surface is observed with the lower full widths at half maximum (FWHM) of X-ray rocking curves (XRC) compared with the other two kinds of nitridation procedures. A smaller FWHM of in-plane XRC peak anisotropy features are reversed, which is consistent with the smaller in-plane stress anisotropic distribution in a-plane AlN, when the two-step nitridation or buffer growth method is used. In four kinds of initial growth procedures, the two-step buffer method is the suitable method for the growth of a-plane AlN by HVPE with the high crystal quality and more isotropic distribution.     

Optical properties of MOVPE-grown a-plane GaN and AlGaN

a-Plane GaN and AlGaN were grown on r-plane sapphire by low-pressure metal-organic vapor epitaxy (LP-MOVPE), and the effects of reactor pressure (from 40 to 500 Torr) and growth temperature (from 1020 to 1100 °C) on the crystalline quality and surface morphology of a-plane GaN were studied. The a-plane GaN grown under 40 Torr had a smooth-surface morphology but a poor crystalline quality; however, the a-plane GaN grown under 500 Torr had higher crystalline quality and optical properties, whose full-width at half-maximum of the X-ray rocking curve (XRC-FWHM) and intensity of yellow luminescence (YL) were smaller. Furthermore, the optical properties of a-plane GaN were investigated by photoluminescence (PL) in detail. We also studied the emission properties of a-plane Al_0.35Ga_0.65N grown at room temperature.     

AlGaN epitaxial lateral overgrowth on Ti-evaporated GaN/sapphire substrate

AlGaN growth using epitaxial lateral overgrowth (ELO) by metalorganic chemical vapor deposition on striped Ti, evaporated GaN on sapphire, has been investigated. AlGaN/AlN films growth on GaN/AlGaN superlattices (SLs) structure on the Ti masks, with various SLs growth temperature (1030, 1060 and 1090 °C) were grown. With increasing the growth temperature, AlGaN surface became flat. The AlGaN film had a cathodoluminescence peak around 345 nm. However, in secondary ion mass spectrometry (SIMS) measurement, Ti signal was detected on the top of AlGaN surface when GaN/AlGaN SLs was grown on Ti striped masks. By inserting the AlN blocking layer on SLs, Ti diffusion was stopped at the AlN layer, and the AlGaN crystalline quality was improved.     

Effect of NH3 flow rate on m-plane GaN growth on m-plane SiC by metalorganic chemical vapor deposition

This paper reports a study of the effect of NH₃ flow rate on m-plane GaN growth on m-plane SiC with an AlN buffer layer. It is found that a reduced NH₃ flow rate during m-plane GaN growth can greatly improve the recovery of in situ optical reflectance and the surface morphology, and narrow down the on-axis (1 0 1¯ 0) X-ray rocking curve (XRC) measured along the in-plane a-axis. The surface striation along the in-plane a-axis, a result of GaN island coalescence along the in-plane c-axis, strongly depends on the NH₃ flow rate, an observation consistent with our recent study of kinetic Wulff plots. The pronounced broadening of the (1 0 1¯ 0) XRC measured along the c-axis is attributed to the limited lateral coherence length of GaN domains along the c-axis, due to the presence of a high density of basal-plane stacking faults, most of which are formed at the GaN/AlN interface, according to transmission electron microscopy.     

Growth of high quality a-plane GaN epi-layer on r-plane sapphire substrates with optimization of multi-buffer layer

Nonpolar (1 1–2 0) a-plane GaN films have been grown using the multi-buffer layer technique on (1–1 0 2) r-plane sapphire substrates. In order to obtain epitaxial a-plane GaN films, optimized growth condition of the multi-buffer layer was investigated using atomic force microscopy, high resolution X-ray diffraction, and transmission electron microscopy measurements. The experimental results showed that the growth conditions of nucleation layer and three-dimensional growth layer significantly affect the crystal quality of subsequently grown a-plane GaN films. At the optimized growth conditions, omega full-width at half maximum values of (11–20) X-ray rocking curve along c- and m-axes were 430 and 530 arcsec, respectively. From the results of transmission electron microscopy, it was suggested that the high crystal quality of the a-plane GaN film can be obtained from dislocation bending and annihilation by controlling of the island growth mode.     

Hydrothermal growth of ZnO nanorods on a-plane GaN/sapphire template

ZnO nanorod arrays are grown on a-plane GaN template/r-plane sapphire substrates by hydrothermal technique. Aqueous solutions of zinc nitrate hexahydrate and hexamethylenetetramine were employed as growth precursors. Electron microscopy and X-ray diffraction measurements were carried out for morphology, phase and growth orientation analysis. Single crystalline nanorods were found to have off-normal growth and showed well-defined in-plane epitaxial relationship with the GaN template. The 〈0 0 0 1〉 axis of the ZnO nanorods were observed to be parallel to the 〈1 0 1¯ 0〉 of the a-plane GaN layer. Optical property of the as-grown ZnO nanorods was analyzed by room temperature photoluminescence measurements.     

One-sidewall-seeded epitaxial lateral overgrowth of a-plane GaN by metalorganic vapor-phase epitaxy

The selective regrowth of GaN during sidewall-seeded epitaxial lateral overgrowth was performed. In addition to adjusting the V/III ratio, control of offset angle of the sidewall was found to be effective for realizing one-sidewall-seeded a-plane (1 1 2¯ 0) GaN on r-plane (1 1¯ 0 2) sapphire. The number of coalescence regions on the grooves was reduced, and threading-dislocation and stacking-fault densities as low as 10⁶–10⁷ cm⁻² and 10³–10⁴ cm⁻¹, respectively, were successfully realized.     

Fabrication of freestanding m-plane GaN wafer by using the HVPE technique on an aluminum carbide buffer layer on an m-plane sapphire substrate

A freestanding m-plane GaN wafer is fabricated by using the hydride vapor-phase epitaxy (HVPE) technique on an aluminum carbide buffer layer on an m-plane sapphire substrate. X-ray pole-figure measurements show a clear m-plane orientation of the GaN surface. The full-width at half-maximum (FWHM) of GaN (1 1¯ 0 0) X-ray rocking curve (XRC) with the scattering vector along the [1 1 2¯ 0] direction is approximately 800 arcsec; this indicates good crystallinity. On the other hand, the FWHM for the case in which the scattering vector is oriented along the [0 0 0 1] direction is broad; this suggests the influence of structural defects along this direction. In fact, basal plane stacking faults (BSF) with a density of approximately 3×10⁵ cm⁻¹ is observed by transmission electron microscopy (TEM). The preparation of a 45-mm-diameter m-plane GaN wafer due to spontaneous separation of the GaN layer from the sapphire substrate is demonstrated.     

Epitaxial lateral overgrowth on (2 1¯ 1¯ 0) a-plane GaN with [0 1¯ 1 1]-oriented stripes

Epitaxial lateral overgrowth was applied to a-plane GaN on r-plane sapphire using SiO₂ stripe masks oriented parallel to [0 1¯ 1 1]. Coalescence and defect distribution was studied using scanning electron microscopy and cathodoluminescence. Defects, i.e., threading dislocations and basal plane stacking faults from the template propagate into the overgrown layer through the mask openings. Stacking faults spread into the whole overgrown layer, whereas threading dislocations are laterally confined in the region above the mask where a part of them is terminated at the inclined coalescence boundary. Lateral overgrowth and dislocation termination at the coalescence boundary leads to an improvement in luminescence intensity and crystal quality, in comparison to the template. The measured XRD rocking curve FWHM were 453″ with incidence along the [0 0 0 1] c-direction and 280″ with incidence along the [0 1 1¯ 0] m-direction.     

Polar dependence of impurity incorporation and yellow luminescence in GaN films grown by metal-organic chemical vapor deposition

We have investigated the unintentional impurities, oxygen and carbon, in GaN films grown on c-plane, r-plane as well as m-plane sapphire by metal-organic chemical vapor deposition. The GaN layer was analyzed by secondary ion mass spectroscopy. The different trend of the incorporation of oxygen and carbon has been explained in the polar (0 0 0 1), nonpolar (1 1 2¯ 0) and semipolar (1 1 2¯ 2) GaN by a combination of the atom bonding structure and the origin direction of the impurities. Furthermore, it has been found that there is a stronger yellow luminescence (YL) in GaN with higher concentration of carbon, suggesting that C-involved defects are originally responsible for the YL.     

The effects of annealing on non-polar (1 1 2¯ 0) a-plane GaN films

Non-polar a-plane (1 1 2¯ 0) GaN films were grown on r-plane sapphire by metal–organic vapor phase epitaxy and were subsequently annealed for 90 min at 1070 °C. Most dislocations were partial dislocations, which terminated basal plane stacking faults. Prior to annealing, these dislocations were randomly distributed. After annealing, these dislocations moved into arrays oriented along the [0 0 0 1] direction and aligned perpendicular to the film–substrate interface throughout their length, although the total dislocation density remained unchanged. These changes were accompanied by broadening of the symmetric X-ray diffraction 1 1 2¯ 0 ω-scan widths. The mechanism of movement was identified as dislocation glide, occurring due to highly anisotropic stresses (confirmed by X-ray diffraction lattice parameter measurements) and evidenced by macroscopic slip bands observed on the sample surface. There was also an increase in the density of unintentionally n-type doped electrically conductive inclined features present at the film–substrate interface (as observed in cross-section using scanning capacitance microscopy), suggesting out-diffusion of impurities from the substrate along with prismatic stacking faults. These data suggest that annealing processes performed close to film growth temperatures can affect both the microstructure and the electrical properties of non-polar GaN films.     

Growth of (1 0 1¯ 3¯ ) semipolar GaN on m-plane sapphire by hydride vapor phase epitaxy

The crystalline, surface, and optical properties of the (1 0 1¯ 3¯) semipolar GaN directly grown on m-plane sapphire substrates by hydride vapor phase epitaxy (HVPE) were investigated. It was found that the increase of V/III ratio led to high quality (1 0 1¯ 3¯) oriented GaN epilayers with a morphology that may have been produced by step-flow growth and with minor evidence of anisotropic crystalline structure. After etching in the mixed acids, the inclined pyramids dominated the GaN surface with a density of 2×10⁵ cm⁻², revealing the N-polarity characteristic. In the low-temperature PL spectra, weak BSF-related emission at 3.44 eV could be observed as a shoulder of donor-bound exciton lines for the epilayer at high V/III ratio, which was indicative of obvious reduction of BSFs density. In comparison with other defect related emissions, a different quenching behavior was found for the 3.29 eV emission, characterized by the temperature-dependent PL measurement.     

Growth and characterization of c-plane AlGaN on γ-LiAlO2

This study demonstrates a pure c-plane AlGaN epilayer grown on a γ-LiAlO₂ (1 0 0) (LAO) substrate with an AlN nucleation layer grown at a relatively low temperature (LT-AlN) by metal-organic chemical vapor deposition (MOCVD). The AlGaN film forms polycrystalline film with m- and c-plane when the nucleation layer grows at a temperature ranging from 660 to 680 °C. However, a pure c-plane AlGaN film with an Al content of approximately 20% can be obtained by increasing the LT-AlN nucleation layer growth temperature to 700 °C. This is because the nuclei density of AlN increases as the growth temperature increases, and a higher nuclei density of AlN deposited on LAO substrate helps prevent the deposition of m-plane AlGaN. Therefore, high-quality and crack-free AlGaN films can be obtained with a (0 0 0 2) ω-rocking curve FWHM of 547 arcsec and surface roughness of 0.79 nm (root-mean-square) using a 700-°C-grown LT-AlN nucleation layer.     

Structural and electrical properties of Si-doped a-plane GaN grown on r-plane sapphire by MOVPE

Approximately 2-μm-thick Si-doped a-plane GaN films with different doping concentrations were grown on approximately 8-μm-thick undoped a-plane GaN/r-sapphire by metal organic vapor phase epitaxy (MOVPE). The structural and electrical properties of the Si-doped a-plane GaN films were investigated by high-resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM) and temperature-dependent Hall measurement. The results showed that a small amount of Si doping can improve the surface morphology and decrease the density of pits. Upon increasing the CH₃SiH₃ flow rate, the crystalline quality of the (0 0 0 2) plane was slightly improved. The highest room-temperature mobility of 83.4 cm²/Vs was obtained at a carrier density of 6.2×10¹⁸ with a CH₃SiH₃ flow rate of 10 sccm.     

MOVPE of AlN-free hexagonal GaN/cubic SiC/Si heterostructures for vertical devices

The heterostructures of GaN/SiC/Si were prepared without using AlN or AlGaN buffer layers (AlN buffers) in the metalorganic vapor phase epitaxy of GaN on SiC. GaN (0 0 0 1) with specular surface was obtained. The AlN buffers are usually used in the conventional growth of GaN on SiC due to the poor nucleation of GaN on SiC. Instead, the nucleation of GaN was controlled by varying the partial pressure of H₂ in the carrier gas, the mixture of H₂ and N₂, during the low-temperature (600 °C) growth of GaN (LT-GaN). After the LT-GaN, the high-temperature (1000 °C) growth of GaN was performed using pure H₂ as the carrier gas. The epitaxial film of cubic SiC (1 1 1) on a Si (1 1 1) substrate was used as the SiC template. Increasing the partial pressure of H₂ in the carrier gas decreased the coverage of SiC surface by LT-GaN. It is suggested that the hydrogen atoms adsorbed on the surface of SiC is preventing the nucleation of GaN.     

Influence of AlGaN/GaN/InGaN superlattice on the characteristics of LEDs grown by metalorganic chemical vapor deposition

This study examined the influence of strain-compensated triple AlGaN/GaN/InGaN superlattice structures (SLs) in n-GaN on the structural, electrical and optical characteristics of LEDs by analyzing the etch pits density (EPD), stress measurement, high-resolution X-ray diffraction (HRXRD), sheet resistance, photoluminescence (PL) and light–current–voltage (L–I–V). EPD, stress measurement and HRXRD studies showed that the insertion of AlGaN/GaN/InGaN SLs during the growth of n-GaN effectively distributed and compensated for the strong compressive stress, and decreased the dislocation density in n-GaN. The operating voltage at 20 mA for the LEDs grown with SLs decreased to 3.18 V from 3.4 V for the LEDs grown without SLs. In addition, a decrease in the spectral blue shift compared to the LEDs grown without SLs was observed in the LEDs grown with the SLs.     

Low-pressure HVPE growth of crack-free thick AlN on a trench-patterned AlN template

A thick AlN layer was grown on a trench-patterned AlN/sapphire template by low-presssure hydride vapor phase epitaxy (LP-HVPE). Compared with the AlN layer grown on a flat AlN/sapphire template, the AlN layer grown on the trench-patterned AlN/sapphire template had a crack-free and smooth surface. The typical full-widths at half-maximum (FWHMs) of X-ray rocking curves (XRC) for the (0 0 0 2), (1 0 1¯ 2), and (1 0 1¯ 0) diffractions of the AlN layer on the trench-patterned AlN/sapphire template were 132, 489, and 594 arcsec, respectively. In addition, atomic steps were observed on the AlN layer on the trench-patterned AlN/sapphire template, and the root-mean-square (RMS) roughness of the AlN layer was determined to be 0.602 nm by atomic force microscopy (AFM).     

Influence of off-cut angle of r-plane sapphire on the crystal quality of nonpolar a-plane AlN by LP-HVPE

The effect of the off-cut angle of an r-plane sapphire substrate has been investigated on the growth of a-plane AlN thick layer by low-pressure hydride vapor phase epitaxy (LP-HVPE). The off-cut angle (θ) was changed from +5.0° (close to c-axis) to −5.0° (close to m-axis). Results show that the crystalline quality and surface morphology are very sensitive to the sign of θ off-angle. The plus θ off-angle is found to be dramatically reduce the full-widths at half-maximum (FWHM) of X-ray rocking curves (XRC), compared with the minus θ off-angle. In-plane FWHM anisotropic feature marked as M- or W-shape dependence on azimuth angle was observed for a-plane AlN. The shape and degree of anisotropy depend on the sign of θ off-angle, while the plus of θ off-angle will leads to the W-shape and the decreased anisotropy. The minimum crystal tilts and twists of the films are observed for the vicinal sapphires with the plus off-angles of +0.2° to +1.0°.     

Growth of a-plane GaN on r-plane sapphire by self-patterned nanoscale epitaxial lateral overgrowth

We report on the use of a novel technique to grow the nonpolar a-plane GaN on r-plane sapphire by metal–organic chemical vapor deposition. A thin InGaN interlayer was deposited on the substrate followed by a low temperature (LT) GaN buffer layer. A stripe-like template was obtained by annealing the LT GaN/InGaN layers at 1100 °C for 2 min. This special template facilitated the nanoscale epitaxial lateral overgrowth of a-plane GaN. Scanning electron microscopy shows that the surface morphology was rather flat for a 1 μm-thick sample. The improvement in crystalline quality was also demonstrated by high-resolution x-ray diffraction, room temperature Raman spectroscopy and photoluminescence measurements. Compared with the traditional epitaxial lateral overgrowth technique, our technique greatly simplified the template preparing process and the crystalline quality of a-plane GaN was improved.