聚对二甲苯纳米纤维阵列的CVD液晶模板法制备及降解性能

聚对二甲苯(PPX)具有优异的生物相容性和化学稳定性, 将其构建成仿细胞外基质结构的可降解纳米纤维在生物工程领域具有重要意义. 本文采用化学气相沉积(CVD)法, 以向列型热致液晶E7为模板, 以4-羟甲基-对二甲苯二聚体(PCP-CH₂OH)为聚-(4-羟甲基-对二甲苯)(PPX-CH₂OH)的前驱体, 通过在其分子链上引入 5,6-苯并-2-亚甲基-1,3-二氧杂环庚烷(BMDO)链段制备BMDO/PPX-CH₂OH共聚物纳米纤维阵列, 探讨了共聚物纳米纤维阵列形貌的影响因素, 分析得到了制备共聚物纳米纤维阵列的最佳反应条件, 并研究了BMDO/PPX-CH₂OH共聚物纳米纤维阵列的生物降解性能. 研究表明, 在液晶模板作用下, 通过CVD法成功地使PCP-CH₂OH与BMDO共聚, 并得到了BMDO/PPX-CH₂OH共聚物纳米纤维阵列; 其形貌主要受样品台的温度和沉积速率的影响, 而单体质量比影响较小; 经优化后CVD最佳条件为: 样品台温度-10 ℃, 沉积速率约为0.01 nm/s, 单体质量比为10∶1; 共聚物在37 ℃的0.1 mol/L Na₂CO₃/0.1 mol/L NaHCO₃的缓冲溶液体系下可有效降解, 当降解时间超过23 d后, 纳米纤维阵列中的酯基可完全分解; 当降解时间超过30 d时, 纳米纤维阵列基本降解完全, 总体呈碎片状.     

一种具有核-壳结构的聚合物纳米胶粒的制备及其药物运载性能

以丙烯酸异丁酯(IBA)、甲基丙烯酸二甲氨乙酯(DMAEMA)、丙烯酸羟乙酯(HEA)作为聚合单体,利用种子微乳液聚合制备了一种具有核-壳结构的聚合物纳米胶粒P(DMAEMA-co-IBA)/P(IBA-co-HEA);采用红外光谱仪、动态激光光散射仪、透射电镜分析了所得胶粒的结构和形貌;将叶酸成功嵌入聚合物胶粒,得到直径约293nm的球形载药胶粒,利用药物体外释放测定了药物运载性能.结果表明,所制备的共聚物纳米胶粒呈球形,直径约275nm,粒径分布较窄,并具有核-壳结构;其对药物具有缓释性和pH响应性.     

荧光双重敏感响应型水溶聚合物的合成及其发光性能研究

将丙烯酰氯与荧光素反应,合成出丙烯酸酯单体3-丙烯酰氧基荧光素(Ac-Flu),然后采用自由基溶液聚合法将Ac-Flu与丙烯酰胺(AM)共聚,制备得到含有荧光素生色团的水溶性荧光共聚物poly(Ac-Flu-co-AM).合成单体Ac-Flu和共聚物poly(Ac-Flu-co-AM)采用核磁(NMR),质谱(HR-MS),红外光谱(FTIR),示差扫描量热法(DSC),可见紫外分光光度仪(UV-Vis)等方法进行了结构表征,同时采用荧光光谱对共聚物poly(Ac-Flu-co-AM)的荧光极其荧光对温度和pH敏感响应性进行了测定研究.结果表明,poly(Ac-Flu-co-AM)的水溶液和薄膜在520 nm附近均具有较强的荧光发射.其中,水溶液荧光强度在0～60℃范围内随着温度的升高呈线性下降,表现出较好的温度敏感响应性质.同时,水溶液荧光强度在pH=4～10范围内随着碱性的增强而升高,表现出较好的pH敏感响应性质.     

含金刚烷基的N-异丙基丙烯酰胺共聚物水凝胶的制备和性能研究

合成了含金刚烷基的甲基丙烯酸金刚烷酯(AdMA)疏水单体,并通过与N-异丙基丙烯酰胺(NIPAM)共聚,制备了温敏性的(P(NIPAM-co-AdMA))共聚物水凝胶.用傅里叶变换红外光谱仪(FTIR)表征了凝胶的化学结构,用环境扫描电镜(ESEM)对凝胶断层结构的形貌进行了观察,用DSC测试了凝胶的体积相转变温度(LCST),并研究了共聚水凝胶的溶胀性能.结果表明,共聚物水凝胶的LCST能够高效地通过改变疏水单体的含量来调节,在实验所考察的范围内,LCST随AdMA含量的增加而线性降低;疏水单体的含量对凝胶的孔洞结构和溶胀性能存在一最优值,在最优的单体配比下,水凝胶具有均匀规整的大孔结构和超快的响应速率.如疏水单体含量为3%(AdMA∶NIPAM=3%)的共聚物水凝胶具有如渔网般均匀的多孔结构,当发生去溶胀时,在5min内就可以失去92%的水,不到10min的时间就可以完全达到去溶胀平衡,水保留率在4%以下.     

苯胺与吡咯共聚物空心球的自组装制备及性能

以碱性溶液为反应介质,苯胺和吡咯为单体,采用稀释聚合法制备苯胺-吡咯共聚物自组装空心微球.研究了搅拌条件、共聚单体摩尔比、聚合反应介质和聚合时间对共聚物形貌的影响.采用扫描电子显微镜、透射电子显微镜、红外光谱、广角X射线衍射、热重分析仪和四探针技术表征了共聚物的形貌、结构和性能.研究结果表明,聚合反应条件对共聚物的形貌有重大影响,通过调整聚合反应条件,可以实现共聚物形貌的有效调控.共聚单体总摩尔浓度为0.05 mol/L,氨水溶液作为反应介质,在静态条件下反应24 h可以得到尺寸均一、平均外直径为610～863 nm,壳厚144～162 nm的自组装共聚物空心微球.同时,研究了共聚物对银离子的吸附性能,结果表明共聚物对银离子有还原作用,吸附后共聚物表面有纳米银的生成.     

磁场-温度双重响应性复合微球的制备与表征

采用部分还原共沉淀法制备了尺寸约为10 nm的Fe₃O₄磁性纳米粒子, 并用油酸对其进行表面改性, 通过无皂乳液聚合的方法将Fe₃O₄与温敏性N-异丙基丙烯酰胺-丙烯酰胺共聚物(PNIPAAm-co-Am)复合, 获得了具有磁场和温度双重响应的复合微球. 采用TEM, FTIR和XRD等方法研究了复合微球的结构与形貌, 分别采用动态激光光散射(DLS)和振动样品磁强计(VSM)表征了复合微球的温度响应性和磁场响应性. 结果表明, 所制备的Fe₃O₄/(PNIPAAm-co-Am)复合微球具有核壳结构, 尺寸约为100 nm, 该微球具有良好的磁响应性和温度响应性, 其最低临界溶解温度(LCST)约为40 ℃.     

聚烯丙基氯化铵模板对AM/AA共聚物结构的影响

采用IR,1H-NMR和13C-NMR研究了聚烯丙基氯化铵(PAAC)模板对丙烯酰胺(AM)/丙烯酸(AA)共聚产物结构的影响,发现这种模板对共聚物P(AM/AA)序列结构和分子量有重要影响.由于共聚合体系中AA单体在PAAC模板聚合物上预组装,使得模板体系共聚物比无模板体系共聚物的AA和AM序列长度显著增加.这种类似多嵌段结构得到pKa′测定的进一步验证.另外模板分子量大小,模板和AA单体摩尔比,AM和AA摩尔比对共聚物结构的影响也进行了研究.应当指出这种模板聚合产物分离模板后仍有少量不能分离掉的PAAC聚合物存在.     

P(MAA-co-AM)纳米水凝胶的制备与表征

利用单体对之间的氢键特殊相互作用,采用一步反应在水相中共聚甲基丙烯酸(MAA)、丙烯酰胺(AM)和交联剂乙二醇二甲基丙烯酸酯(EGDMA),制备了pH响应性共聚物P(MAAco-AM)纳米水凝胶。采用纳米粒度与电位分析仪、傅里叶红外光谱仪、透射电子显微镜、场发射扫描电镜等对P(MAA-co-AM)纳米水凝胶的尺寸、形貌、组成和结构进行了表征。系统研究了反应参数对P(MAA-co-AM)纳米水凝胶的影响。结果表明:当两单体等物质的量投料时所制备的P(MAA-co-AM)纳米水凝胶粒径分布最窄(〈Dh〉=129nm,PDI=0.095),且其粒径随着两单体用量的增加而增大。随着单体加入时间的延长或EGDMA用量的增加,P(MAA-co-AM)纳米水凝胶的粒径逐渐变小。P(MAA-co-AM)纳米水凝胶表现出极好的pH响应性:当介质的pH从4增加到8时,溶胀比高达7,体积扩张了343倍。     

无规-类接枝共聚物自组装制备交联纳米微球

无规-类接枝共聚物(SFG)由大分子单体-己内酯改性丙烯酸酯(FA)、亲油性单体苯乙烯和甲基丙烯酸缩水甘油酯(GMA)共聚所得，SFG与聚苯乙烯在甲醇溶液中进行自组装，形成核壳结构纳米胶束，进一步对PGMA壳进行化学交联。最终得到具有核壳结构的纳米微球。动态激光光散射和透射电子显微镜表征结果显示SFG自组装形成了窄分布的纳米微球，微球粒径在100～200nm之间。     

六苯基取代联苯双酚/氢醌型共聚醚酮的研究

以 4 ,4′ 二氟二苯酮和不同比例的六苯基取代联苯双酚 /氢醌为单体 ,在温和条件下经溶液共缩聚合成了新型共聚醚酮 .采用13 C NMR技术测定共聚物中三种不同连接方式 (AKA ,DKD ,AKD)的平均链段长度(LA,LD) ,共聚物为短嵌段结构 .性能测试结果表明 ,新型共聚醚酮具有良好的溶解性、拉伸强度、较高的耐热性和良好的二氧化碳 /氮气和氧气 /氮气分离能力 .     

Controlled fabrication of one-dimensional polymer nanostructures via metallogel template polymerization

A facile method is reported to controllably fabricate one dimensional(1D) polymer nanostructures via metallogel template polymerization.The metallogel was prepared through coordination interactions between silver ions and a ligand(L) bearing three pyridyl groups in tetrahydrofuran(THF).The diameters of the metallogel nanofibers could be tuned by the gel concentration(GC).Due to its high thermal stability and facility of removal,the metallogel was used as the template for radical polymerization of diacryolyl-2,6-diaminopyridine(DADAP) to form poly-diacryolyl-2,6-diaminopyridine(PDADAP) nanostructures.The gradually eroding of the templates by PDADAP provided us an effective way to fabricate various nanostructures of the polymer.We have demonstrated that different 1D nanostructures,including nanoribbons,nanotubes and nanowires,could be selectively fabricated by adjusting polymerization time,monomer concentration and GC.The rheological properties of the gel samples were tested by a rheometer.As prolonging the reaction time,more and more polymers were formed and the strength of the resulting polymer gels became higher and higher.The simple preparation process,easy controlled microstructures and adequate gel strength would make it a facile synthetic method for different 1D polymer nanosturctures.     

Synthesis and characterization of poly (indene‐co‐pyrrole) nanofibers

Nanofibers of poly (indene‐co‐pyrrole) (CInPy) have been synthesized, using a facile chemical oxidative polymerization reaction. The effect of copolymerization was examined in view of the individually synthesized homopolymer nanostructures of polyindene (PIn) and polypyrrole (PPy). Morphological details of CInPy, studied using scanning electron microscopy (SEM) and transmission electron microscopy, (TEM) reveal the appearance of dense cottony mess, comprising of fine fibers with an average diameter of 5–10 nm. Chemical structural analysis of CInPy, conducted using ultraviolet‐visible (UV‐Vis), Fourier transform infrared (FTIR), and nuclear magnetic resonance (NMR) spectroscopic techniques, reveals that both PIn and PPy are involved in the formation of copolymer organization. Fluorescence properties of nanosized copolymer are observed in the blue region, with emission λ_max placed at 395 nm. Conductivity of copolymer nanofibers (2.4 × 10^?3 S/cm) is consistent with the morphology and thermal stability properties of integral homo‐polymers. Improved thermal stability and processability along with the enhanced optical and electrical properties of copolymer nanostructures outfit it as a better promising material in optoelectronic and light emitting nanodevices, with reference to nanosized PIn and PPy. Copyright © 2009 John Wiley & Sons, Ltd.     

Morphology and mechanical properties of binary triblock copolymer blends

The influence of the morphology on the mechanical properties of binary styrene–butadiene (SB) triblock copolymer blends of a thermoplastic block copolymer and a thermoplastic elastomer (TPE) with different molecular architectures was studied with bulk samples prepared from toluene. Both block copolymers contained SB random copolymer middle blocks, that is, the block sequence S–SB–S. The two miscible triblock copolymers were combined to create a TPE with increased tensile strength without a change in their elasticity. The changes in the equilibrium morphology of the miscible triblock copolymer blends as a function of the TPE content (lamellae, bicontinuous morphology, hexagonal cylinders, and worms) resulted in a novel morphology–property correlation: (1) the strain at break and Young's modulus of blends with about 20 wt % TPE were larger than those of the pure thermoplastic triblock copolymer; (2) at the transition from bicontinuous structures to hexagonal structures (～35 wt % TPE), a change in the mechanical properties from thermoplastic to elastomeric was observed; and (3) in the full range of wormlike and hexagonal morphology (60–100 wt % TPE), elastomeric properties were observed, the strength greatly increasing and high‐strength elastomers resulting. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 429–438, 2005     

Reaction-induced microphase separation in epoxy resin containing polystyrene-block-poly(ethylene oxide) alternating multiblock copolymer

Polystyrene-block-poly(ethylene oxide) alternating multiblock copolymer (PS-alt-PEO) was synthesized with the combination of atom transfer radical polymerization (ATRP) and Huisgen 1,3-dipolar cycloaddition (i.e., click chemistry). The copolymer has been characterized by means of Fourier transform infrared spectroscopy (FTIR), ¹H nuclear magnetic resonance spectroscopy (NMR), gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). The PS-alt-PEO alternating multiblock copolymer was incorporated into epoxy resin to investigate the behavior of reaction-induced microphase separation, which has been compared to the case of the thermosets containing PS-b-PEO diblock copolymer. The morphology of epoxy thermosets containing PS-alt-PEO alternating multiblock copolymer were investigated by means of atomic force microscopy (AFM), and small-angle X-ray scattering (SAXS) and the nanostructures were detected in all the thermosetting blends investigated. In marked contrast to the case of the thermosets containing PS-b-PEO diblock copolymer, the thermosets containing PS-alt-PEO multiblock copolymer displayed disordered nanostructures, which have been interpreted on the basis of the restriction of the alternating multiblock topology of the block on the formation of the nanostructures via reaction-induced microphase separation.     

一种有机酰腙类配体及其金属凝胶的结构及性能

设计合成了一种带有长链烷基和配位基团的新型有机配体2-吡啶甲醛-4'-十二烷氧基苯甲酰腙(简称L),并采用核磁(1H-NMR)、红外(FTIR)、电喷雾质谱(ESI-MS)和元素分析确认其结构.在乙醇和水的混合溶剂中,配体L可使溶剂凝胶化,并可与多种金属离子(Co(Ⅱ),Ni(Ⅱ),Zn(Ⅱ)和Cu(Ⅱ)作用,形成金属凝胶.采用扫描电镜分析表明,L自身形成的凝胶及金属凝胶的微观形貌均为相互搭接的纤维状结构.采用紫外光谱分析表明在乙醇溶液中L分子形成了聚集体.采用平板流变仪分析表明引入金属离子可提高凝胶的强度.进一步合成了L与Cu(Ⅱ)的配合物,通过对比配合物与金属凝胶的红外光谱和紫外光谱,证明金属凝胶中配体L与金属离子间形成了配位作用.     

Growth mechanism of penniform BaWO4 nanostructures in catanionic reverse micelles involving polymers

The formation of penniform BaWO4 nanostructures made of nanowires or nanobelts under the direction of a block copolymer in catanionic reverse micelles has been studied in detail. On the basis of the experimental results obtained from the BaWO4 crystallization in aqueous polymer solutions and careful transmission electron microscopy (TEM) observations of BaWO4 nanostructures formed in reverse micelles containing polymers, a detailed two-stage growth mechanism has been proposed for the formation of the penniform nanostructures in reverse micelles, which involves the polymer-controlled shaft formation (Stage 1) and the mixed surfactants-controlled barb growth (Stage 2). During Stage 1, poly(ethylene glycol)-block-poly(methacrylic acid) (PEG-b-PMAA) induced the formation of c-axis-oriented shuttle-like nanocrystals and the subsequent oriented attachment of these shuttle-like nanocrystals resulted in the formation of [100]-oriented shafts with many parallel [001]-oriented pricks. During Stage 2, [001]-oriented nanowires or nanobelts grew gradually from the pricks into barbs, leading to the formation of well-defined penniform BaWO4 nanostructures with the barb morphology essentially determined by the mixing ratio r of the anionic to cationic surfactants (i.e., nanowires were formed at r=1 while nanobelts were formed at r deviating from 1). The current understanding of the growth mechanism of penniform BaWO4 nanostructures in catanionic reverse micelles involving polymers may be potentially applied for designing a new synthesis system for the controlled synthesis of other hierarchical 1D nanostructures with desired architectures.     

Investigation of the Mechanism Behind Conductive Fluorescent and Multistimuli‐responsive Li+‐enriched Metallogel Formation

A fluorescent metallogel (2.6 % w/v) has been obtained from two non‐fluorescent components viz. phenyl‐succinic acid derived pro‐ligand H₂PSL and LiOH (2 equiv.) in DMF. Li⁺ ion not only plays a crucial role in gelation through aggregation, but also contributed towards enhancement of fluorescence by imposing restriction over excited state intramolecular proton transfer (ESIPT) followed by origin of chelation enhanced fluorescence (CHEF) phenomenon. Further, the participation of CHEF followed by aggregation‐caused quenching (ACQ) and aggregation‐induced emission (AIE) in the gelation process have been well established by fluorescence experiments. Transmission electron microscopy (TEM) analysis disclosed the sequential creation of nanonuclei followed by nanoballs and their alignment towards the generation of fibers of about 3, 31 and 40 nm diameter, respectively. The presence of a long‐range fibrous morphology inside the metallogel was further attested by scanning electron microscopy (SEM). Rheological studies on the metallogel showed its true gel‐phase material nature. Nyquist impedance study shows a resistance value of 7.4 kΩ for the metallogel which upon applying ultrasound increased to 8.5 kΩ, while an elevated temperature of 70 °C caused reduction in the resistance value to 4.8 kΩ. The mechanism behind metallogel formation has been well established by using FTIR, UV‐vis, SEM, TEM, PXRD, ¹H NMR, fluorescence and ESI‐MS.     

Co-templating synthesis of highly dispersed 1D ZnO nanostructures in amorphous SiO2 under hydrothermal condition

One-dimensional (1D) ZnO nanostructures were grown in amorphous SiO₂ matrix by a co-templating method under hydrothermal condition. Using ethylenediamine (EDA) groups grafted mesoporous silica MCM-41 as a co-template, the growth of 1D ZnO nanostructures was oriented by soft EDA groups and confined inside the hard mesochannels of MCM-41. The microstructure and morphology of the 1D-ZnO-nanostructures/SiO₂ composite were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy (EDS). All these results indicate that the 1D ZnO nanostructures were synthesized and highly dispersed in the amorphous SiO₂ matrix. Blue-shifted exciton absorption was observed from the co-templating synthesized sample.     

Reversible Photoswitching in Poly(2-oxazoline) Nanoreactors

This contribution reports light responsive catalytic nanoreactors based on poly(2-oxazoline) diblock copolymers. The hydrophobic block of the copolymer is a random copolymer consisting of a spiropyran functionalized 2-oxazoline (SPOx) and 2-(but-3-yn-1-yl)-4,5-dihydrooxazole (ButynOx), while the hydrophilic block is based on 2-methyl-2-oxazoline (MeOx). The block copolymer is terminated with tris(2-aminoethyl) amine (TREN) that serves as catalyst in a Knoevenagel condensation. Four block copolymers with different ButynOx/SPOx and hydrophilic/hydrophobic ratios are synthesized and self-assembled through solvent exchange. Micelles and vesicles of various sizes are observed by TEM, which undergo morphological and size changes in response to irradiation with UV light. We hypothesize that these transformations in the nanostructures are caused by increases in the hydrophilicity of the hydrophobic block when spiropyran (SP) isomerizes to merocyanine (MC) in the presence of UV light. The reversible transition from micellar to vesicular nanoreactors resulted in increased reaction kinetics through improved substrate accessibility to the catalytic site, or termination of the catalytic reaction due to polymer precipitation. These nanoreactors present a promising platform towards photoregulating reaction outcomes based on changes in nanostructure morphology.     

Metallogel of bis(tetrazole)-appended pyridine derivative with CoBr2 as a chemoprobe for volatile gases containing chloride atom

A bis(tetrazole)-appended ligand 1 formed the metallogel efficiently by mixing with Co²⁺ ion. Interestingly, the metallogel 1 with CoBr₂ showed the orange yellow colour, which has octahedral structure. The rheological properties of metallogel obtained with CoBr₂ were ca. 1.5-fold larger than that for the metallogel obtained with CoCl₂. Upon addition of HCl, SOCl₂, (COCl)₂ and COCl₂ containing chloride atoms in the metallogel 1 prepared with CoBr₂ changed from orange yellow to blue-green colour. These results indicate that the octahedral structure of metallogel was converted into the tetrahedral structure. On the other hand, no significant colour changes were observed in the presence of an excess of other anions, namely HF, HBr, HI, HNO₃ and H₂SO₄. These findings indicate that the metallogel 1 with CoBr₂ is useful as a chemoprobe for gases containing chloride atom.