The simple and rapid spectrophotometric determination of trace chromium(VI) after preconcentration as its colored complex on chitin

Preconcentration method with collection of metal complexes on a chitin has been applied to the spectrophotometric determination of chromium(VI) in water. The chromium(VI) is collected as its 1,5-diphenylcarbazide(DPC) complex on a column of chitin in the presence of dodecyl sulfate as counter-ion. The Cr-DPC complex retained on the chitin is eluted with a methanol-1 M acetic acid mixture (7:3, v/v), and the absorbance of the eluent is measured at 541 nm. Beer's law is obeyed over the concentration range of 0.05-0.6 mug of chromium(VI) in 1 ml of the eluent. The apparent molar absorptivity is 3.5x10(4) dm(3) mol(-1) cm(-1). The tolerance limits for Fe(III) is low, i.e. ten times that of chromium(VI), but some metal ions and common inorganic anions do not interfere in concentration range of 100-10 000 times that of chromium(VI). The present method can be applied to the determination of chromium(VI) in natural water samples.     

Test Determination of Lead and Zinc in Water with the Use of Xylenol Orange Immobilized on Silica

Xylenol Orange immobilized on silica as a complex of iron(III) was used for the test determination of lead(II) and zinc(II) in drinking water over concentration ranges of 10–100 and 13–130 g/L, respectively. The maximum distribution coefficients were found to be 7.50 × 10³ mL/g for Pb and 3.75 × 10³ mL/g for Zn. The macro main trace components of water at a level of their maximum permissible concentrations caused no interference. Al(III), Fe(III), and Zn(II) in the presence of NH₄F did not interfere with the determination of Pb(II), whereas lead in the presence of acetate caused no interference with the determination of Zn(II).     

High-performance liquid chromatographic determination of uranium using solvent extraction and bis(salicylaldehyde) tetramethylethylenediimine as complexing reagent

The reagent bis(salicylaldehyde)tetramethylethylenediimine has been used for the determination of dioxouranium(VI), based on complexation in aqueous solution at pH 6, followed by extraction in chloroform and HPLC determination on a Hypersil ODS (3 μm) column. The complex was eluted with the ternary mixture methanol-acetonitrile-water (40:30:30, v/v/v), with UV detection at 260 nm. Oxovanadium(IV), iron(III), copper(II), cobalt(II), nickel(II) and palladium(II) were completely separated and did not interfere in the determination of uranium. The linear calibration range and detection limits have been obtained. The method has been applied to the determination of uranium together with copper, iron and nickel in mineral ore samples.     

Selective spectrophotometric determination of iron(III) with EDTA

A spectrophotometric determination of iron as its iron (III)-EDTA-H₂O₂-NH₃ complex is described; up to 10-fold amounts of metals that form EDTA complexes absorbing at the same wavelength do not interfere because hydrogen peroxide reacts with thciron(IIl)-EDTA complex but does not affect the EDTA complexes of coppcr(II), nickel(II), cobalt(ltl) and chromium(Ilt).     

Ion-exchanger colorimetry-III microdetermination of zinc in water

An ion-exchanger colorimetric method for the determination of zinc(II) with Zincon has been developed. Zinc in a water sample can be determined by sorption onto an anion-exchange resin from 2M chloride solution followed by transformation into a coloured complex with Zincon. With use of a 1-litre sample the sensitivity is 10 times greater than that for conventional colorimetry. Most metals, except cadmium(II), lead(II) and bismuth(III), do not interfere when present in up to 100 times the concentration of zinc. The zinc: Zincon ratio of the complex in the resin phase was found to be 1 : 1 by the molar ratio method.     

Determination of Iron (II) in Water by a Spectrophotometric Method After Preconcentration on an Organic Solvent-Soluble Membrane Filter

Abstract

A solvent-soluble membrane filter is proposed for a simple and rapid preconcentration and spectrophotometric determination of iron (II), which was collected on a nitrocellulose membrane filter as an ion-associate of the cationic complex of iron (II)-1,10-phenanthroline with an anionic surfactant of dodecyl sulfate. The ion-associate collected was dissolved in 5 ml of 2-methoxyethanol together with the filter. The color intensity due to the ion-associate in the resulting solution was measured at 510 nm against a reagent blank. Beer's law is obeyed in the range 1–15 μg Fe (II) in 5 ml of solvent with excellent reproducibility, and detection limits better than 0.5 μg dm^?3 as Fe (II) can be achieved. The diverse components normally present in water do not interfere when proper masking reagent is added. The proposed method has been applied to the analysis of water samples from several sources such as river water, ground water and tapwater samples, the recoveries of the iron (II) added to the samples are quantitative, and results found are satisfactory.     

Determination of microamounts of iron by hydroxamate resin colorimetry

Summary A new, sensitive chelating ion-exchanger colorimetric method has been developed for the determination of iron at the g/l level in water, based on the direct measurement of light absorption of iron hydroxamate resin complex. In 0.2 N perchloric acid solution, iron could be rapidly, selectively and quantitatively absorbed on the hydroxamate resin. The calibration curve for iron(III) of a 25 ml solution was linear in the concentration range 8.00×10^–6 to 5.00×10^–5 M. For iron(III) with larger sample volumes, the relative detection limit was increased. Most of the metals interfered negligibly, such as Ca(II), Co(II), Cu(II), Ni(II) and Zn(II), except for higher concentration of lead(II) and mercury(II) when present at up to 400 times the concentration of iron(III). The effects of EDTA, glycine, thiourea, phosphate, nitrate and chloride on the retention of iron(III) were also examined. Only thiourea significantly influenced the retention of iron(III). The presence of sodium chloride even at a concentration of 3.5×10⁴ times that of iron(III) did not interfere at all.

---

Bestimmung von Mikromengen Eisen durch Hydroxamatharz-Colorimetrie

     

Trace Analysis of Iron in Environmental Water and Snow Samples from Poland

Abstract

A voltammetric method for the determination of iron at detection limit of 4 μg/l is described, using the catalytic current of the reduction of the Fe(III)-triethanolamine (TEA) complex in the presence of bromate ions. the determination was performed at a mercury hanging drop electrode without preconcentration, using the TEA alkaline solution as a supporting electrolyte and the differential pulse technique. A peak current for the Fe(III)-TEA catalytic reduction was observed at a potential of-1.0 V (Ag/AgCl saturated electrode). the influence of TEA, BrO³ and NaOH concentrations on the peak height was studied. It was found that a 100-fold excess of Mn, a 50-fold excess of Cr(VI) and Zn did not interfere in the determination. This method was applied to the determination of iron in water, snow and waste water samples.     

Spectrophotometric determination of vanadium(IV) with nitrilotriacetic acid

A new and convenient spectrophotometric method for the estimation of vanadium(IV) with NTA is described. The minimum ratio of metal ion to ligand, working pH, wavelength for maximum absorbance of the complex ion, and the effect of various cations and anions are described. The complex ion obeys Beer's law in the concentration range 1–32 mmol/liter of the vanadium(IV) ion. It is observed that iron(II), cobalt(II), nickel(II), copper(II), and oxidizing anions such as chromate and nitrite interfere in this determination, whereas managanese(II), chromium(III), iron(III), and anions like nitrate, chloride, bromide, iodide, thiocyanate, sulfate, and sulfite do not have any effect. Excessive amounts of acetate, phosphate, oxalate, tartrate and thiosulfate must also be avoided in this determination. Anions and cations which interfere in the determination of vanadium(IV) by NTA should not be present in the system.     

Determination of trace amounts of iron by catalytic-adsorptive stripping voltammetry

A highly sensitive and selective voltammetric procedure is described for the determination of trace amounts of iron. The procedure is based on the adsorptive collection of an iron-thiocyanate-nitric oxide complex on a hanging mercury drop electrode. The adsorbed complex catalyzes the reduction of nitrite in solution, which gives a detection limit of 40 ppt iron (30 s accumulation). The stripping current increases linearly with iron concentration up to 80 ppb. The relative standard deviations are 4.2% and 1.6% at 0.5 ppb and 40 ppb respectively. Most of the common ions, except cobalt, do not interfere with the determination of iron. The procedure is applied to determine iron in biological samples, natural waters and analytical-grade chemicals.     

DCTA Titration of iron(III) with p-aminosalicylic acid and sodium azide as indicators

Iron(III) has been determined by DCTA titration with p-aminosalicylic acid and sodium azide as indicator at pH 1.4-3.5. The titrations are rapid, simple, accurate and reversible and as little as 0.15 mg of iron(III) can be determined in the presence of up to 100 times as much of certain ions. Cadmium, zinc, lead, copper(II), aluminium, thorium, oxalate, phosphate, fluoride and sulphide interfere. The method is utilized for determination of iron(III) in presence of copper(II) or lead and in limestone, cement and haemetite.     

The spectrophotometric determination of trace molybdenum (VI) after collection and elution as molybdate ion on protonated chitin

Collection and elution method for inorganic anion on protonated chitin has been applied to the spectrophotometric determination of molybdenum (VI). The molybdenum (VI) is collected as molybdate ion on a column of chitin in weak acidic medium which is easily eluted with a small volume of 0.1 M ammonia buffer solution (pH 10). The molybdenum (VI) in the eluent is determined by bromopyrogallol red-Zephiramine method spectrophotometrically. Beer's law is obeyed over the concentration range of 0.1-0.8 mug of molybdenum (VI) in 1 ml of eluent at 634 nm. The apparent molar absorptivity is 6x10(4) dm(3) mol(-1) cm(-1). The tolerance limits for WO(4)(2-), VO(3)(-), CrO(4)(2-) and Fe (III) is low, that is, 1-100 times that of molybdenum (VI), but some metal ions and common inorganic anions do not interfere in concentration range of 1000-5000 times that of molybdenum (VI). The present method can be applied to the determination of molybdenum (VI) in natural water samples.     

Spectrophotometric determination of Rauwolfia alkaloids: estimation of reserpine in pharmaceuticals.

A simple, sensitive and economically viable spectrophotometric method for the determination of some Rauwolfia alkaloids (ajmaline, ajmalicine, reserpine and yohimbine-HCl) has been developed. The method involves the oxidation of Rauwolfia alkaloids by iron(III) and subsequent complexation of iron(II) with 1,10-phenanthroline, forming a red-colored complex having the maximum absorbance at 510 nm. The method is applied to the determination of reserpine in tablets of pharmaceutical formulations. The common excipients do not interfere with the proposed method. A statistical comparison of these results with those of a reported method shows good agreement and indicates no significant difference in the precision.     

Determination of bismuth(III) by direct potentiometry and potentiometric titration, with an electrode sensitive to Bi(3+)

A liquid-state ion-exchange electrode containing the chelate bismuth(III) complex with 5-mercapto-3-(naphthyl-2)-1,3,4-thiadiazole-2-thione in tetrachloroethane is applied to the determination of bismuth(III) by direct potentiometry and potentiometric titration. The influence of various interfering cations is discussed. In the presence of potassium cyanide as masking agent, Ni(II), Co(II), Cu(II), Ag(I) and Hg(II) do not interfere in the potentiometric EDTA titration. Satisfactory results have been obtained for the determination of bismuth(III) in Wood's metal and two pharmaceuticals.     

Separation and determination of trace amounts of aluminium(III), vanadium(V), iron(III), copper(II) and nickel(II) with CALKS and PAR by RP-HPLC.

An RP-HPLC method for the separation and determination of aluminium(III), vanadium(V), iron(III), copper(II) and nickel(II) with CALKS (Chromazol KS) and PAR ([4-(2-pyridylazo)resorcinol]) chelating on a YWG-ODS column was developed. A mixture of methanol-tetrahydrofuran(THF)-water (60:5:35 v/v) containing 0.2 mol/L LiCl, 5 x 10(-5) mol/L CALKS, 5 x 10(-5) mol/L PAR and acetate buffer solution (pH 4.9) was selected as mobile phase. The method has high sensitivity, with the detection limits being 6 ng/mL for aluminium(III), 3.5 ng/mL for vanadium(V), 10.4 ng/mL for iron(III), 6.3 ng/mL for copper(II) and 8.7 ng/mL for nickel(II). It also has good selectivity, so that most foreign metal ions do not interfere under the optimum conditions. The method can be applied to the simultaneous determination of trace amounts of aluminium, vanadium, iron, copper and nickel in rice and flour samples.     

Spectrophotometric estimation of cobalt(II) with nitrilotriacetic acid

A convenient and efficient method for the estimation of cobalt(II) ions in the presence of other metal ions is described. Interference of metal ions such as iron(II), iron(III), nickel(II), manganese(II), and copper(II) have been investigated. Only iron(III) ions seriously affect this determination. Copper(II) and nickel(II) ions do not interfere if present in a molar-ratio less than 1:2 in the cobalt(II) ion solution. Cobalt(II)-nickel(II) and cobalt(II)-copper(II) binary mixtures can be efficiently analyzed at selective wavelengths.     

Simultaneous determination of iron(II) and iron(III) in aqueous solution by kinetic spectrophotometry with tiron

A kinetic spectrophotometric method that requires no prior measurement of rate constants is developed for the simultaneous determination of iron(II) and iron(III). The method is based on the aerial oxidation of iron(II) in the presence of tiron and acetate ions. The iron(III) formed is subsequently complexed with tiron and the absorbance/time relation is evaluated. The concentrations of iron(III) and iron(II) are obtained from the absorbance values at the start and at equilibrium, respectively, calculated by non-linear least-squares fitting. A linear calibration graph is obtained up to 12 μg ml^?1 iron(II)/iron(III). The method is applied to iron-rich ground water.     

Spectrophotometric determination of Fe(II) with 2,4,6-tri(2'-pyridyl)-1,3,5-triazine in the presence of large quantities of Fe(III) and complexing ions

A spectrophotometric method for the determination of Fe(II) in the presence of large amounts (up to 800 mg/l.) of Fe(III) is suggested. The Fe(III) is effectively masked by complexing with fluoride at pH 2.0-2.4 before development of the violet Fe(II) complex with 2,4,6-tri(2'-pyridyl)-1,3,5-triazine. The absorbance is measured at 595 nm. Various commonly occurring ions which complex with Fe(II) and/or Fe(III) do not interfere.     

Etude analytique et dosage de micro- et submicro-traces de manganese par polarographie inverse

A method is proposed for the determination of manganese(II) by anodic stripping polarography. A systematic study was made of the various factors affecting the course of pre-electrolysis as well as the anodic stripping. A procedure is given for the determination of i ng of manganese with a precision of ± 12.7%. The selectivity of the method was studied in the presence of 14 cations ; hydrogen ions interfere at pH <5, Co²⁺ interferes at concentrations equal to that of Mn²⁺, and Mo⁷⁺ and V⁵⁺ at concentrations ?50 times that of Mn²⁺. The other ions studied do not interfere at concentrations 100–1000 times higher. An application to pharmaceutical analysis is described.     

Spectrophotometric and derivative spectrophotometric determination of aluminium with Hydroxynaphthol Blue

The reaction of aluminium(III) with Hydroxynaphtol Blue (HNB) in aqueous media at apparent pH 5.5 results in a red complex that is stable for at least 4 hr. Beer's Law is obeyed up to 1.6 microg/ml of aluminium(III) with an apparent molar absorptivity of 1.66 x 10(4) l.mol(-1). cm(-1) at 569 nm. This paper proposes procedures for aluminium(III) determination by ordinary and first-derivative spectrophotometry. The results demonstrated that the linear dynamic range is 0.03-1.60 microg/ml for ordinary spectrophotometry and 11.8-320.0 ng/ml for first derivative spectrophotometry. The HNB is not selectivity for aluminium, but the addition of EDTA allows the aluminium determination in the presence of accepted amounts of Ca(II), Mg(II), Mn(II), Ba(II), Sr(II), Cd(II), Pb(II), La(III), In(III), Bi(III) and Zn(II). The interference of Cu(II) and Hg(II) can be masked by thiosulphate. Ions such as UO(2)(II), Mo(VI), Co(II), Ti(IV) and PO(4)(III) do interfere seriously. This method was applied for aluminium determination in copper-base alloy, zinc-base alloy, magnesium-base alloy, iron ore, manganese ore, cement, dolomite, feldspar and limestone. The results indicated high accuracy and precision.