Analysis of β‐blockers in groundwater using large‐volume injection coupled‐column reversed‐phase liquid chromatography with fluorescence detection and liquid chromatography time‐of‐flight mass spectrometry

Atenolol, nadolol, metoprolol, bisoprolol and betaxolol were simultaneously determined in groundwater samples by large‐volume injection coupled‐column reversed‐phase liquid chromatography with fluorescence detection (LVI‐LC‐LC‐FD) and liquid chromatography‐time‐of‐flight mass spectrometry (LC‐TOF‐MS). The LVI‐LC‐LC‐FD method combines analyte isolation, preconcentration and determination into a single step. Significant reductions in costs for sample pre‐treatment (solvent and solid phases for clean up) and method development times are also achieved. Using LC‐TOF‐MS, accurate mass measurements within 3 ppm error were obtained for all of the β‐blockers studied. Empirical formula information can be obtained by this method, allowing the unequivocal identification of the target compounds in the samples. To increase the sensitivity, a solid‐phase extraction step with Oasis MCX cartridge was carried out yielding recoveries of 79–114% (n=5) with RSD 2–7% for the LC‐TOF‐MS method. SPE gives a high purification of β‐blockers compared with the existing methods. A 100% methanol wash was allowed for these compounds with no loss of analytes. Limit of quantification was 1–7 ng/L for LVI‐LC‐LC‐FD and 0.25–5 ng/L for LC‐TOF‐MS. As a result of selective extraction and effective removal of coextractives, no matrix effect was observed in LVI‐LC‐LC‐FD and LC‐TOF‐MS analyses. The methods were applied to detect and quantify β‐blockers in groundwater samples of Almería (Spain).     

On-line liquid chromatography – gas chromatography for automated clean-up and analysis of polycyclic aromatic hydrocarbons

A fully automated system, comprising a liquid chromatograph (LC) coupled on-line to a gas chromatograph (GC) by means of a loop interface, has been constructed for clean-up and analysis of polycyclic aromatic hydrocarbons (PAH). An autosampler was utilized for sample injection into the LC. By the use of a back-flush technique in conjunction with an ordinary analytical aminopropylsilica column, PAH could be isolated by LC: a concurrent solvent evaporation injection technique was then used for on-line transfer of the PAH fraction to the GC, where the PAH analysis was completed. Compared with ordinary off-line LC clean-up followed by GC analysis, the sensitivity has been increased by a factor of 50–100, yielding a detection limit for individual PAH of a few nanograms per sample when using flame ionization detection. Further, irreproducible losses of low molecular weight PAH as a result of solvent evaporation steps in off-line clean-up procedures have been eliminated. Reproducibility of retention times and relative peak areas is high, facilitating automatic peak identification and calculation of concentrations, and the system can thus be used for automatic sample evaluation. The total time required for clean-up and analysis is only 1.5 hours, and the demand on personnel time for the analysis of PAH has been drastically reduced. The technique has been demonstrated with samples of urban air and of used automobile engine lubricating oil.     

On-line coupling of liquid chromatography,capillary gas chromatography and mass spectrometry for the determination and identification of polycyclic aromatic hydrocarbons in vegetable oils

Summary An on-line combination of liquid chromatography, gas chromatography and mass spectrometry has been realized by coupling a quadrupole mass spectrometer to an LC-GC apparatus. Liquid chromatography was used for sample pretreatment of oil samples of different origin. The appropriate LC fraction, containing polycyclic aromatic hydrocarbons, was transferred to the gas chromatograph using a loop-type interface. After solvent evaporation through the solvent vapour exit and subsequent GC separation, the compounds were introduced into the mass spectrometer for detection and identification. The GC column was connected to a short piece of deactivated fused silica that protruded into the ion source. The total analytical set-up allowed the direct analysis of oil samples after dilution in n-pentane without any sample clean-up. Detection limits are about 40 pg in the full scan mode and about 1 pg with selective ion monitoring, i.e. 20 ppb and 0.5 ppb respectively.     

Fast sample preparation involving MASE and coupled column normal phase liquid chromatography for the rapid trace analysis of dioxins in air-dust samples from fire catastrophe emissions

A new approach has been developed and tested for the urgent analysis of dioxins in samples of air-dust filters originating from catastrophe emissions. The procedure consists of a fast extraction of the sample with microwave solvent extraction (MASE) and acetone as solvent followed by a fast cleanup of the extract with normal phase coupled column liquid chromatography (LC/LC).

The multi-dimensional LC/LC system employs a 50 mm×4.6 mm i.d. column packed with 3 μm silica and a 150 mm×4.6 mm i.d. column packed with 5 μm PYE as the first and second analytical column, respectively. Iso-hexane is used on both columns to perform cleanup and dichloromethane to perform efficient back-flush elution of the compounds from the second column. The obtained polarity-based separation in the first dimension and molecular-structure based separation in the second dimension provides a fast and powerful cleanup.

Validation was done by analysing samples of homemade RIVM air-dust with aged residues (n=8, spiking level about 15 pg mg⁻¹ per compound) of dioxins/furans and samples of reference Urban Dust SRM 1649a (n=4) with both the new approach and the existing conventional procedure and were instrumentally analyzed with capillary gas chromatography and high resolution mass spectrometric detection (GC/HRMS).

In comparison to the existing conventional procedure, the new approach reduces sample processing from several days to several hours per sample.

As regards the aged-residue air-dust samples, the new method shows a good accuracy, precision and high selectivity providing a performance in good agreement with the existing procedure. In SRM air-dust, the concentration of a few compounds obtained by the new method was below (10–50%) the certified value.     

Identification and structural characterization of in vivo metabolites of ketorolac using liquid chromatography electrospray ionization tandem mass spectrometry (LC/ESI‐MS/MS)

In vivo metabolites of ketorolac (KTC) have been identified and characterized by using liquid chromatography positive ion electrospray ionization high resolution tandem mass spectrometry (LC/ESI‐HR‐MS/MS) in combination with online hydrogen/deuterium exchange (HDX) experiments. To identify in vivo metabolites, blood urine and feces samples were collected after oral administration of KTC to Sprague–Dawley rats. The samples were prepared using an optimized sample preparation approach involving protein precipitation and freeze liquid separation followed by solid‐phase extraction and then subjected to LC/HR‐MS/MS analysis. A total of 12 metabolites have been identified in urine samples including hydroxy and glucuronide metabolites, which are also observed in plasma samples. In feces, only O‐sulfate metabolite and unchanged KTC are observed. The structures of metabolites were elucidated using LC‐MS/MS and MSⁿ experiments combined with accurate mass measurements. Online HDX experiments have been used to support the structural characterization of drug metabolites. The main phase I metabolites of KTC are hydroxylated and decarbonylated metabolites, which undergo subsequent phase II glucuronidation pathways. Copyright © 2012 John Wiley & Sons, Ltd.     

Analysis of tocopherols in margarine by on-line HPLC–HRGC coupling

Tocopherol analysis in margarine is usually carried out by HPLC after saponification of the sample and extraction of the vitamin compounds; these steps consume both time and solvents. In this paper we propose an on-line HPLC–HRGC coupling method, which allows us to simplify the preparation of the analytical sample. The sample of margarine is solubilized in hexane in an ultrasonic bath in the dark; the filtered solution is then injected into the liquid chromatograph using a normal phase microbore column eluted with hexane–isopropanol 99.8:0.2. The α-tocopherol, which is eluted with some wax esters, is transferred on-line to the gas chromatograph, using a loop-type interface with the concurrent eluent evaporation and solvent vapor exit, thus it is separated from interfering compounds and determined using an Alltech RSL 300 column (22 m × 0.25 μm i.d., 0.2 μm film thickness). The β, γ, and δ–tocopherols are determined in the same LC run, using fluorimetric detection. The analysis was carried out in 50 min.     

Experimental design optimization of the separation of the aromatic compounds in petroleum cuts by supercritical fluid chromatography

A experimental design optimization method is demonstrated for evaluation of the resolution of the performance mixture used in the proposed ASTM test to determine the aromatic content of aviation fuels. The method uses a Doehlert experimental matrix test to optimize the resolution and analysis time by varying the pressure and temperature of the supercritical carbon dioxide mobile phase. The separation between saturated and aromatic compounds was optimized using only seven experiments. With this procedure, the analysis time required for determination of the total aromatic content of more complex samples can be reduced to less than 10 min.     

Characterization of High‐Pressure Liquid Chromatography Columns using Chromatographic Methods

Abstract

A great variety of columns for liquid chromatography (LC) are available in dimensions ranging from industrial scale to micro‐bore, nano‐bore, and capillary size, and on‐chip columns. The columns may be used in various liquid chromatography modes or in capillary electrochromatography, depending on the support materials and stationary phase chemistry. Every year many new column types are introduced on the market, with improved selectivity and efficiency, long lifetime, and mobile phase compatibility, intended for general use, for liquid chromatography/mass spectrometry (LC/MS) applications, proteomic research, or for the analysis of other specific sample types. Considerable improvement in pH, high‐temperature, and high‐pressure stability of new column types, together with advances in the instrumentation, enabled introduction of capillary, high‐temperature, and ultra‐high‐pressure HPLC into routine practice. Even though reversed‐phase mode is still by the most widely used in contemporary LC, applications of other separation modes (such as ion, normal‐phase, or high‐interaction liquid chromatography (HILC)) have become more frequent recently, because of unique separation selectivity for certain sample types.

Characterization of column quality is not a simple task, because a number of factors should be taken into account, that affect the selectivity, efficiency and resolution of sample separation and the reproducibility of chromatographic data. These include the type of the support, the arrangement and density of the stationary phase on the adsorbent surface, the homogeneity of the chromatographic bed, etc. Various physicochemical techniques are used for characterization of the properties of column packings however, most of them are suitable for bulk materials only and cannot be directly applied for commercial columns without damaging them. Not to destroy the columns, often precious and expensive, practicing chromatographers can apply chromatographic methods to characterize columns and evaluate their analytical suitability under real‐life conditions, where the intermolecular interactions between the analytes, the stationary phase, and the mobile phases affect the retention. The present review reports various chromatographic tests and strategies available for column evaluation.     

Selective and sensitive detection of organic contaminants in water samples by on-line trace enrichment–gas chromatography–mass spectrometry

Liquid chromatographic (LC) type trace enrichment is coupled online with capillary gas chromatography (GC) with mass spectrometric (MS) detection for the analysis of aqueous samples. A volume of 1–10 ml of an aqueous sample is preconcentrated on a trace-enrichment column packed with a polymeric stationary phase. After cleanup with HPLC-grade water the precolumn is dried with nitrogen and subsequently desorbed with ethyl acetate. A fraction of 60 μl is introduced on-line into a diphenyltetramethyldisilazane-deactivated retention gap under partially concurrent solvent evaporation conditions and using an early solvent vapor exit. The analytes are separated and detected by means of GC–MS. The potential of the LC–GC–MS system for monitoring organic pollutants in river and drinking water is studied. Target analysis is carried out with atrazine and simazine as model compounds; the detection limits achieved under full-scan and multiple ion detection conditions are 30 pg and 5 pg, respectively. Identification of unknown compounds (non-target analysis), is demonstrated using a river water sample spiked with 168 pollutants varying in polarity and volatility.     

Identification and determination of the saikosaponins in Radix bupleuri by accelerated solvent extraction combined with rapid‐resolution LC‐MS

A method based on accelerated solvent extraction combined with rapid‐resolution LC–MS for efficient extraction, rapid separation, online identification and accurate determination of the saikosaponins (SSs) in Radix bupleuri (RB) was developed. The RB samples were extracted by accelerated solvent extraction using 70% aqueous ethanol v/v as solvent, at a temperature of 120°C and pressure of 100 bar, with 10 min of static extraction time and three extraction cycles. Rapid‐resolution LC separation was performed by using a C₁₈ column at gradient elution of water (containing 0.5% formic acid) and acetonitrile, and the major constituents were well separated within 20 min. A TOF‐MS and an IT‐MS were used for online identification of the major constituents, and 27 SSs were identified or tentatively identified. Five major bioactive SSs (SSa, SSc, SSd, 6″‐O‐acetyl‐SSa and 6″‐O‐acetyl‐SSd) with obvious peak areas and good resolution were chosen as benchmark substances, and a triple quadrupole MS operating in multiple‐reaction monitoring mode was used for their quantitative analysis. A total of 16 RB samples from different regions of China were analyzed. The results indicated that the method was rapid, efficient, accurate and suitable for use in the quality control of RB.     

Determination of target fat‐soluble micronutrients in rainbow trout's muscle and liver tissues by liquid chromatography with diode array‐tandem mass spectrometry detection

This paper describes an analytical approach, based on LC‐diode array detector‐MS/MS (LC‐DAD‐MS/MS), for characterizing the fat‐soluble micronutrient fraction in rainbow trout (Oncorhynchus mykiss ). Two different procedures were applied to isolate the analytes from liver and muscle tissue: overnight cold saponification to hydrolyze bound forms and to simplify the analysis; matrix solid‐phase dispersion to avoid artifacts and to maintain unaltered the naturally occurring forms. Analytes were separated on a C₃₀ analytical column by using a nonaqueous reversed mobile phase compatible with the atmospheric pressure chemical ionization. Compared to other works, the most relevant advantage of the here illustrated method is the large amount of information obtained with few analytical steps: nine fat‐soluble vitamins (3,4‐dehydroretinol, retinol, cholecalciferol, ergocalciferol, α‐tocopherol, γ‐tocopherol, δ‐tocopherol, phylloquinone, and menaquinone‐4) and eight carotenoids (all‐trans ‐lutein, all‐trans ‐astaxanthin, all‐trans ‐zeaxanthin, all‐trans ‐β‐cryptoxanthin, all‐trans ‐canthaxanthin, all‐trans ‐ζ‐carotene, all‐trans ‐β‐carotene, and all‐trans ‐γ‐carotene) were quantified after the method validation, while other untargeted carotenoids were tentatively identified by exploiting the identification power of the LC‐DAD‐MS/MS hyphenation.     

Direct-injection high performance liquid chromatography ion trap mass spectrometry for the quantitative determination of olanzapine,clozapine and N-desmethylclozapine in human plasma

A specific and sensitive direct-injection high performance liquid chromatography electrospray ionization tandem mass spectrometry (HPLC/ESI-MS/MS) method has been developed for the rapid identification and quantitative determination of olanzapine, clozapine, and N-desmethylclozapine in human plasma. After the addition of the internal standard dibenzepin and dilution with 0.1% formic acid, plasma samples were injected into the LC/MS/MS system. Proteins and other large biomolecules were removed during an online sample cleanup using an extraction column (1 x 50 mm i.d., 30 microm) with a 100% aqueous mobile phase at a flow rate of 4 mL/min. The extraction column was subsequently brought inline with the analytical column by automatic valve switching. Analytes were separated on a 5 microm Symmetry C18 (Waters) analytical column (3.0 x 150 mm) with a mobile phase of acetonitrile/0.1% formic acid (20:80, v/v) at a flow rate of 0.5 mL/min. The total analysis time was 6 min per sample. The inter- and intra-assay coefficients of variation for all compounds were <11%. By eliminating the need for extensive sample preparation, the proposed method offers very large savings in total analysis time.     

Silver-ion reversed-phase comprehensive two-dimensional liquid chromatography combined with mass spectrometric detection in lipidic food analysis

The triacylglycerol (TAG) profiles present in real world lipidic samples are usually quite complex and, as such, monodimensional high-performance liquid chromatographic (HPLC) techniques are inadequate when challenged with such matrices. In this respect, the complementary use of silver-ion (Ag) and non-aqueous (NA) reversed-phase (RP) HPLC can be exploited if thorough TAG separations are required. The present investigation reports the employment of a newly developed comprehensive LC (LC x LC) system, based on the different separation mechanisms of the aforementioned techniques, and applied to a rice oil sample. The approach was successful in the separation of a high number of solutes, otherwise unachievable through monodimensional LC. Furthermore, the use of atmospheric pressure chemical ionization mass spectrometry (APCI-MS), as detection system, provided a third analytical dimension boosting the identification power of the comprehensive chromatographic method.     

Preventing false negatives with high-resolution mass spectrometry: the benzophenone case

Benzophenone (BP) is one of the many contaminants reported as present in foodstuffs due to its migration from food packaging materials. Liquid chromatography/tandem mass spectrometry (LC/MS/MS) is acknowledged in the literature as the method of choice for this analysis. However, cases have been reported where the use of this methodology was insufficient to unambiguously confirm the presence of a contaminant. In previous work performed by the authors, the unequivocal identification of BP in packaged foods was not possible even when monitoring two m/z transitions (precursor ion – product ion), since ion ratio errors higher than 20% were obtained. In order to overcome this analytical problem a fast, sensitive and selective liquid chromatography/high‐resolution mass spectrometry (LC/HRMS) methodology has been developed and applied to the analysis of BP in packaged foods. A direct comparison between LC/HRMS and LC/MS/MS data indicated better selectivity when working with LC/HRMS at a resolving power of 50 000 FWHM (full width at half maximum) than when monitoring two m/z transitions by LC/MS/MS. The resolving power used enabled the detection and identification of Harman as the compound impeding the confirmation of BP by LC‐MS/MS. Similar quantitative results were obtained by an Orbitrap mass analyser (Exactive?) and a triple quadrupole mass analyser (TSQ Quantum Ultra AM?). Copyright © 2011 John Wiley & Sons, Ltd.     

高效液相色谱-气相色谱在线联用同时测定土壤中饱和烃和芳香烃

为加强对土壤中石油烃类污染物的风险管控,生态环境部已将石油烃类列为土壤中的重点监测项目。石油烃源于石油与合成油,是涵盖一定碳数范围的碳氢化合物,主要分为饱和烃和芳香烃两大类。芳香烃通常是高度烷基化的单环、双环与多环芳烃,其对人和动物的毒性较饱和烃大很多,因此,仅仅测定土壤中总石油烃含量难以准确评估其环境毒性。目前环境领域的标准方法尚未区分土壤中饱和烃和芳香烃。该研究针对土壤样品的基质干扰特点,对样品的提取和净化环节进行了优化,并且应用高效液相色谱-气相色谱在线联用(HPLC-GC)技术,建立了同时测定土壤中饱和烃和芳香烃的方法。其中,提取方法选择正己烷-乙醇(1∶1, v/v)以固液比1∶4常温振荡提取1 h,然后水洗去除乙醇,取正己烷层提取液净化;净化方法选择自制硅胶柱,以正己烷-二氯甲烷(8∶2, v/v)洗脱;洗脱液经浓缩注入HPLC-GC分析,以内标法同时测定试液中的饱和烃和芳香烃,方法的定量限为0.4 mg/kg。该方法经过土壤石油烃标准物(SQC-116)验证,测定值在证书提供的可信区间内,相对误差(RE)为10.6%,相对标准偏差(RSD)为1.4%,说明方法准确可靠且精密度达到分析要求。最后,该文采用建立的方法检测了北京地区的5个土壤样品,结果表明:5个样品均含有饱和烃(C₁₀~C₄₀),其含量范围为3.3~32.1 mg/kg;其中4个样品中检出芳香烃(C₁₀~C₄₀),其含量范围为0.8~4.3 mg/kg;此外,通过谱图分析还可以初步判别烃类物质的污染来源。     

Analysis of polychlorinated biphenyls in transformer oils by automated on-line coupling reversed phase liquid chromatography-gas chromatography using the through oven transfer adsorption desorption (TOTAD) Interface

An automated method for the direct analysis of polychlorinated biphenyls (PCBs) in transformer oil is presented. The proposed method uses the TOTAD (through oven transfer adsorption desorption) interface for the on-line coupling of reversed phase liquid chromatography and gas chromatography (RPLC-GC). In this fully automated system, the oil is injected directly with no sample pre-treatment step other than dilution with n-propanol and filtration. In the LC step, PCBs are separated from other components of the oils using methanol/water (90:10 v/v) as mobile phase, at a flow rate of 1?mL?min^?1. The LC fraction containing the PCBs is automatically transferred to the GC by the TOTAD interface and GC analysis enables the separation of the PCB congeners. The proposed method is compared with two other methods: the European Norm (UNE-EN-61619) and that of the American Society for Testing and Materials (ASTM) (D4059-00). The proposed method practically eliminates the time-consuming sample preparation step and avoids errors caused by sample manipulation. The total PCB concentrations obtained with the three methods are similar.     

Liquid chromatographic trace enrichment with on-line capillary gas chromatography for the determination of organic pollutants in aqueous samples

Trace enrichment for the GC analysis of a series of chlorinated pesticides and polychlorinated biphenyls (PCBs) in aqueous samples has been achieved through a simple on-line technique involving sorption on an LC micro-precolumn followed by direct elution into a gas chromatograph with hexane. A 5-m retention gap coupled to the capillary GC column served as the recipient of a relatively large sample volume (ca. 100 μl) introduced into the GC. Partially concurrent solvent evaporation during sample introduction allowed a large sample capacity. Recoveries of more than 95% were observed for the majority of the compounds studied. Using 1.0 ml aqueous samples, detection limits of less than 1 ppt were found. The applicability of the developed method was demonstrated for a river water sample.     

Polar solvents for the desorption of a liquid chromatographic precolumn coupled on-line with a capillary gas chromatograph

Coupling column liquid chromatography and gas chromatography on-line is becoming more important in analytical chemistry. Especially when large amounts of polar solvents can be introduced into the gas chromatograph without any problem, the technique will offer new possibilities. With a DPTMDS retention gap, evaporation rates and flooded zones of some solvents have been determined. Two modes of operation using partially concurrent solvent evaporation conditions are discussed: (1) injecting a sample via a loop of an LC valve followed by introduction into the gas chromatograph with an LC pump; (2) trace enrichment on a precolumn followed by on-line desorption with n-propanol into the gas chromatograph. Preliminary results for a splitter system, inserted between the retention gap and the analytical column which allows a considerable increase of the evaporation rate are also presented.     

Comparison of LC and LC/MS methods for quantifying <Emphasis Type="Italic">N</Emphasis>-glycosylation in recombinant IgGs

High-performance liquid chromatography (LC) and liquid chromatography/electrospray ionization time-of-flight mass spectrometry (LC/ESI-MS) methods with various sample preparation schemes were compared for their ability to identify and quantify glycoforms in two different production lots of a recombinant monoclonal IgG1 antibody. IgG1s contain a conserved N-glycosylation site in the fragment crystallizable (Fc) subunit. Six methods were compared: (1) LC/ESI-MS analysis of intact IgG, (2) LC/ESI-MS analysis of the Fc fragment produced by limited proteolysis with Lys-C, (3) LC/ESI-MS analysis of the IgG heavy chain produced by reduction, (4) LC/ESI-MS analysis of Fc/2 fragment produced by limited proteolysis and reduction, (5) LC/MS analysis of the glycosylated tryptic fragment (293EEQYNSTYR301) using extracted ion chromatograms, and (6) normal phase HPLC analysis of N-glycans cleaved from the IgG using PNGase F. The results suggest that MS quantitation based on the analysis of Fc/2 (4) is accurate and gives results that are comparable to normal phase HPLC analysis of N-glycans (6).     

Cyclic polyamide oligomers extracted from nylon 66 membrane filter disks as a source of contamination in liquid chromatography/mass spectrometry

Background interferences are perhaps an unavoidable part of analytical detection schemes, particularly when analyzing trace level samples or when using detectors with high levels of sensitivity. In liquid chromatography, mobile phase solvents are routinely filtered using membrane filter disks to trap particulates in hopes of minimizing contamination, providing improvements in data output and instrumental operation. In this study, we report that one such filter disk leads to a significant level of contamination in LC and LC/MS experiments. Extractable compounds from nylon membrane filters generate significant background signals in UV absorption chromatograms at 214 nm, and are also detected by electrospray ionization mass spectrometry, with nominal m/z values of 453 and 679. It is shown that rinsing the nylon membranes before their use can reduce, but will not eliminate, the extractable contaminants from the mobile phase. Through MS and tandem MS analysis, we have identified these contaminants as cyclic oligomers of polyamide 66. Based on these results, it is recommended that nylon membrane filters be avoided when conducting trace level analysis, particularly when conducting LC/MS experiments.