Wetting characteristics of aqueous rhamnolipids solutions

The wetting properties of surfactants on solid surfaces form the basis of many industrial and biological processes. The preferential adsorption of the surfactants from aqueous solutions onto solid surfaces alter the adhesion tension of the surface and this behavior may cause partial to complete wetting of the surfaces by the aqueous surfactant solutions. However, different types of surfactants show different wetting characteristics. To study the wetting properties of biologically produced rhamnolipids (RL), advancing contact angles of the aqueous solutions of the RL mixture of R1 and R2 in a ratio of R2/R1=1.1 were measured as a function of surfactant concentration. For a comparison of the wetting performance, sodium dodecyl sulfate (SDS) was chosen as the reference surfactant. A hydrophilic glass surface, a hydrophobic polymer, polyethylene terephthalate (PET), and gold surface were used as the solid surfaces to determine the wetting characteristics of rhamnolipids. At low surfactant concentrations (RL concentration <3x10(-5)M, SDS concentration<3x10(-4)M) contact angle (Theta) varied in a certain range depending on the character of the surfactant interactions with the surface. This was followed by a decrease in contact angle. Parallel to this behavior, at low surfactant concentrations the adhesion tension decreased, then remained constant and an increase at higher surfactant concentrations was obtained on hydrophobic surfaces. On hydrophilic surfaces a steady decrease in adhesion tension was observed with both surfactant solutions.     

Selective wetting of heterogeneous surfaces by solutions of surfactants

Selective wetting of dimethyldichlorosilane-modified glass plates by solutions of tetradecyltrimethylammonium bromide (TDTAB), a cationic surfactant, in p-xylene has been studied. When surfactant concentrations are lower than the critical micelle concentration (CMC), the contact angles under selective wetting conditions increase with increasing hydrophobic surface fraction. When surfactant concentrations are higher than CMC, contact angles are the same on all substrates studied. The adsorption of the surfactant on hydrophilic and hydrophobic regions of heterogeneous surfaces and the stability of wetting films are taken into account in interpreting the results.     

Measurement of the kinetic rate constants for the adsorption of superspreading trisiloxanes to an air/aqueous interface and the relevance of these measurements to the mechanism of superspreading

Super-spreading trisiloxane surfactants are a class of amphiphiles which consist of nonpolar trisiloxane headgroups ((CH3)3-Si-O)2-Si(CH3)(CH2)3-) and polar parts composed of between four and eight ethylene oxides (ethoxylates, -OCH2CH2-). Millimeter-sized aqueous drops of trisiloxane solutions at concentrations well above the critical aggregate concentration spread rapidly on very hydrophobic surfaces, completely wetting out at equilibrium. The wetting out can be understood as a consequence of the ability of the trisiloxanes at the advancing perimeter of the drop to adsorb at the air/aqueous and aqueous/hydrophobic solid interfaces and to reduce considerably the tensions of these interfaces, creating a positive spreading coefficient. The rapid spreading can be due to maintaining a positive spreading coefficient at the perimeter as the drop spreads. However, the air/aqueous and solid/aqueous interfaces at the perimeter are depleted of surfactant by interfacial expansion as the drop spreads. The spreading coefficient can remain positive if the rate of surfactant adsorption onto the solid and fluid surfaces from the spreading aqueous film at the perimeter exceeds the diluting effect due to the area expansion. This task is made more difficult by the fact that the reservoir of surfactant in the film is continually depleted by adsorption to the expanding interfaces. If the adsorption cannot keep pace with the area expansion at the perimeter, and the surface concentrations become reduced at the contact line, a negative spreading coefficient which retards the drop movement can develop. In this case, however, a Marangoni mechanism can account for the rapid spreading if the surface concentrations at the drop apex are assumed to remain high compared to the perimeter so that the drop is pulled out by the higher tension at the perimeter than at the apex. To maintain a high apex concentration, surfactant adsorption must exceed the rate of interfacial dilation at the apex due to the outward flow. This is conceivable because, unlike that at the contact line, the surfactant reservoir in the liquid at the drop center is not continually depleted by adsorption onto an expanding solid surface. In an effort to understand the rapid spreading, we measure the kinetic rate constants for adsorption of unaggregated trisiloxane surfactant from the sublayer to the air/aqueous surface. The kinetic rate of adsorption, computed assuming the bulk concentration of monomer to be uniform and undepleted, represents the fastest that surfactant monomer can adsorb onto the air/aqueous surface in the absence of direct adsorption of aggregates. The kinetic constants are obtained by measuring the dynamic tension relaxation as trisiloxanes adsorb onto a clean pendant bubble interface. We find that the rate of kinetic adsorption is only of the same order as the area expansion rates observed in superspreading, and therefore the unaggregated flux cannot maintain very high surface concentrations at the air/aqueous interface, either at the apex or at the perimeter. Hence in order to maintain either a positive spreading coefficient or a Marangoni gradient, the surfactant adsorptive flux needs to be augmented, and the direct adsorption of aggregates (which in the case of the trisiloxanes are bilayers and vesicles) is suggested as one possibility.     

Model and experimental studies for contact angles of surfactant solutions on rough and smooth hydrophobic surfaces

Despite the practical need, no models exist to predict contact angles or wetting mode of surfactant solutions on rough hydrophobic or superhydrophobic surfaces. Using Gibbs' adsorption equation and a literature isotherm, a new model is constructed based on the Wenzel and Cassie equations. Experimental data for aqueous solutions of sodium dodecyl sulfate (SDS) contact angles on smooth Teflon surfaces are fit to estimate values for the adsorption coefficients in the model. Using these coefficients, model predictions for contact angles as a function of topological f (Cassie) and r (Wenzel) factors and SDS concentration are made for different intrinsic contact angles. The model is also used to design/tune surface responses. It is found that: (1) predictions compare favorably to data for SDS solutions on five superhydrophobic surfaces. Further, the model predictions can determine which wetting mode (Wenzel or Cassie) occurred in each experiment. The unpenetrated or partially penetrated Cassie mode was the most common, suggesting that surfactants inhibit the penetration of liquids into rough hydrophobic surfaces. (2) The Wenzel roughness factor, r, amplifies the effect of surfactant adsorption, leading to larger changes in contact angles and promoting total wetting. (3) The Cassie solid area fraction, f, attenuates the lowering of contact angles on rough surfaces. (4) The amplification/attenuation is understood to be due to increased/decreased solid-liquid contact-area.     

Aggregation work at polydisperse micellization: ideal solution and "dressed micelle" models comparing to molecular dynamics simulations

General thermodynamic relations for the work of polydisperse micelle formation in the model of ideal solution of molecular aggregates in nonionic surfactant solution and the model of "dressed micelles" in ionic solution have been considered. In particular, the dependence of the aggregation work on the total concentration of nonionic surfactant has been analyzed. The analogous dependence for the work of formation of ionic aggregates has been examined with regard to existence of two variables of a state of an ionic aggregate, the aggregation numbers of surface active ions and counterions. To verify the thermodynamic models, the molecular dynamics simulations of micellization in nonionic and ionic surfactant solutions at two total surfactant concentrations have been performed. It was shown that for nonionic surfactants, even at relatively high total surfactant concentrations, the shape and behavior of the work of polydisperse micelle formation found within the model of the ideal solution at different total surfactant concentrations agrees fairly well with the numerical experiment. For ionic surfactant solutions, the numerical results indicate a strong screening of ionic aggregates by the bound counterions. This fact as well as independence of the coefficient in the law of mass action for ionic aggregates on total surfactant concentration and predictable behavior of the "waterfall" lines of surfaces of the aggregation work upholds the model of "dressed" ionic aggregates.     

Surfactant solutions and porous substrates: spreading and imbibition

In Section 1, spreading of small liquid drops over thin dry porous layers is investigated from both theoretical and experimental points of view [V.M. Starov, S.R. Kosvintsev, V.D. Sobolev, M.G. Velarde, S.A. Zhdanov, J. Colloid Interface Sci. 252 (2002) 397]. Drop motion over a porous layer is caused by an interplay of two processes: (a) the spreading of the drop over already saturated parts of the porous layer, which results in an expanding of the drop base, and (b) the imbibition of the liquid from the drop into the porous substrate, which results in a shrinkage of the drop base and an expanding of the wetted region inside the porous layer. As a result of these two competing processes, the radius of the drop goes through a maximum value over time. A system of two differential equations has been derived to describe the evolution with time of radii of both the drop base and the wetted region inside the porous layer. This system includes two parameters, one accounts for the effective lubrication coefficient of the liquid over the wetted porous substrate, and the other is a combination of permeability and effective capillary pressure inside the porous layer. Two additional experiments were used for an independent determination of these two parameters. The system of differential equations does not include any fitting parameter after these two parameters are determined. Experiments were carried out on the spreading of silicone oil drops over various dry microfiltration membranes (permeable in both normal and tangential directions). The time evolution of the radii of both the drop base and the wetted region inside the porous layer were monitored. All experimental data fell on two universal curves if appropriate scales are used with a plot of the dimensionless radii of the drop base and of the wetted region inside the porous layer on dimensionless time. The predicted theoretical relationships are two universal curves accounting quite satisfactory for the experimental data. According to theory predictions [1]: (i) the dynamic contact angle dependence on the same dimensionless time as before should be a universal function, and (ii) the dynamic contact angle should change rapidly over an initial short stage of spreading and should remain a constant value over the duration of the rest of the spreading process. The constancy of the contact angle on this stage has nothing to do with hysteresis of the contact angle: there is no hysteresis in the system under investigation. These conclusions again are in good agreement with experimental observations [V.M. Starov, S.R. Kosvintsev, V.D. Sobolev, M.G. Velarde, S.A. Zhdanov, J. Colloid Interface Sci. 252 (2002) 397]. In Section 2, experimental investigations are reviewed on the spreading of small drops of aqueous SDS solutions over dry thin porous substrates (nitrocellulose membranes) in the case of partial wetting [S. Zhdanov, V. Starov, V. Sobolev, M. Velarde, Spreading of aqueous SDS solutions over nitrocellulose membranes. J. Colloid Interface Sci. 264 (2003) 481-489]. The time evolution was monitored of the radii of both the drop base and the wetted area inside the porous substrate. The total duration of the spreading process was subdivided into three stages-the first stage: the drop base expands until the maximum value of the drop base is reached; the contact angle rapidly decreases during this stage; the second stage: the radius of the drop base remains constant and the contact angle decreases linearly with time; the third stage: the drop base shrinks and the contact angle remains constant. The wetted area inside the porous substrate expends during the whole spreading process. Appropriate scales were used with a plot of the dimensionless radii of the drop base, of the wetted area inside the porous substrate, and the dynamic contact angle on the dimensionless time. Experimental data showed [S. Zhdanov, V. Starov, V. Sobolev, M. Velarde, Spreading of aqueous SDS solutions over nitrocellulose membranes. J. Colloid Interface Sci. 264 (2003) 481-489]: the overall time of the spreading of drops of SDS solution over dry thin porous substrates decreases with the increase of surfactant concentration; the difference between advancing and hydrodynamic receding contact angles decreases with the surfactant concentration increase; the constancy of the contact angle during the third stage of spreading has nothing to do with the hysteresis of contact angle, but determined by the hydrodynamic reasons. It is shown using independent spreading experiments of the same drops on nonporous nitrocellulose substrate that the static receding contact angle is equal to zero, which supports the conclusion on the hydrodynamic nature of the hydrodynamic receding contact angle on porous substrates. In Section 3, a theory is developed to describe a spontaneous imbibition of surfactant solutions into hydrophobic capillaries, which takes into account the micelle disintegration and the concentration decreasing close to the moving meniscus as a result of adsorption, as well as the surface diffusion of surfactant molecules [N.V. Churaev, G.A. Martynov, V.M. Starov, Z.M. Zorin, Colloid Polym. Sci. 259 (1981) 747]. The theory predictions are in good agreement with the experimental investigations on the spontaneous imbibition of the nonionic aqueous surfactant solution, Syntamide-5, into hydrophobized quartz capillaries. A theory of the spontaneous capillary rise of surfactant solutions in hydrophobic capillaries is presented, which connects the experimental observations with the adsorption of surfactant molecules in front of the moving meniscus on the bare hydrophobic interface [V.J. Starov, Colloid Interface Sci. 270 (2003)]. In Section 4, capillary imbibition of aqueous surfactant solutions into dry porous substrates is investigated from both theoretical and experimental points of view in the case of partial wetting [V. Straov, S. Zhdanov, M. Velarde, J. Colloid Interface Sci. 273 (2004) 589]. Cylindrical capillaries are used as a model of porous media for theoretical treatment of the problem. It is shown that if an averaged pore size of the porous medium is below a critical value, then the permeability of the porous medium is not influenced by the presence of surfactants at any concentration: the imbibition front moves exactly in the same way as in the case of the imbibition of the pure water. The critical radius is determined by the adsorption of the surfactant molecules on the inner surface of the pores. If an averaged pore size is bigger than the critical value, then the permeability increases with surfactant concentration. These theoretical conclusions are in agreement with experimental observations. In Section 5, the spreading of surfactant solutions over hydrophobic surfaces is considered from both theoretical and experimental points of view [V.M. Starov, S.R. Kosvintsev, M.G. Velarde, J. Colloid Interface Sci. 227 (2000) 185]. Water droplets do not wet a virgin solid hydrophobic substrate. It is shown that the transfer of surfactant molecules from the water droplet onto the hydrophobic surface changes the wetting characteristics in front of the drop on the three-phase contact line. The surfactant molecules increase the solid-vapor interfacial tension and hydrophilise the initially hydrophobic solid substrate just in front of the spreading drop. This process causes water drops to spread over time. The time of evolution of the spreading of a water droplet is predicted and compared with experimental observations. The assumption that surfactant transfer from the drop surface onto the solid hydrophobic substrate controls the rate of spreading is confirmed by experimental observations. In Section 6, the process of the spontaneous spreading of a droplet of a polar liquid over solid substrate is analyzed in the case when amphiphilic molecules (or their amphiphilic fragments) of the substrate surface layer are capable of overturning, resulting in a partial hydrophilisation of the surface [V.M. Starov, V.M. Rudoy, V.I. Ivanov, Colloid J. (Russian Academy of Sciences English Transaction) 61 (3) (1999) 374]. Such a situation may take place, for example, during contact of an aqueous droplet with the surface of a polymer whose macromolecules have hydrophilic side groups capable of rotating around the backbone and during the wetting of polymers containing surface-active additives or Langmuir-Blodgett films composed of amphiphilic molecules. It was shown that droplet spreading is possible only if the lateral interaction between neighbouring amphiphilic molecules (or groups) takes place. This interaction results in the tangential transfer of "the overturning state" to some distance in front of the advancing three-phase contact line making it partially hydrophilic. The quantitative theory describing the kinetics of droplet spreading is developed with allowance for this mechanism of self-organization of the surface layer of a substrate in the contact with a droplet.     

Effects of surfactant micelles on viscosity and conductivity of poly(ethylene glycol) solutions

The neutral polymer-micelle interaction is investigated for various surfactants by viscometry and electrical conductometry. In order to exclude the well-known necklace scenario, we consider aqueous solutions of low molecular weight poly(ethylene glycol) (2-20)x10(3), whose radial size is comparable to or smaller than micelles. The single-tail surfactants consist of anionic, cationic, and nonionic head groups. It is found that the viscosity of the polymer solution may be increased several times by micelles if weak attraction between a polymer segment and a surfactant exists, epsilon相似文献   

Spreading behavior of crude oil over limestone substrate

Wetting characteristics of crude oil droplets over limestone substrates in the presence of different aqueous solutions are investigated in terms of wetting length, droplet depth, contact angle, and spreading coefficient. A wide range of concentration of NaOH, Alcoflood polymer, and nonionic Triton X-100 surfactant are used as a continuous phase for the crude oil droplet. NaOH and Triton X-100 significantly enhanced the spreading characteristics of the crude oil droplet; however, AF1235 polymer caused a huge reduction in the spreading behavior of crude oil.     

Foaming and foam stability for mixed polymer-surfactant solutions: effects of surfactant type and polymer charge

Solutions of surfactant-polymer mixtures often exhibit different foaming properties, compared to the solutions of the individual components, due to the strong tendency for formation of polymer-surfactant complexes in the bulk and on the surface of the mixed solutions. A generally shared view in the literature is that electrostatic interactions govern the formation of these complexes, for example between anionic surfactants and cationic polymers. In this study we combine foam tests with model experiments to evaluate and explain the effect of several polymer-surfactant mixtures on the foaminess and foam stability of the respective solutions. Anionic, cationic, and nonionic surfactants (SDS, C(12)TAB, and C(12)EO(23)) were studied to clarify the role of surfactant charge. Highly hydrophilic cationic and nonionic polymers (polyvinylamine and polyvinylformamide, respectivey) were chosen to eliminate the (more trivial) effect of direct hydrophobic interactions between the surfactant tails and the hydrophobic regions on the polymer chains. Our experiments showed clearly that the presence of opposite charges is not a necessary condition for boosting the foaminess and foam stability in the surfactant-polymer mixtures studied. Clear foam boosting (synergistic) effects were observed in the mixtures of cationic surfactant and cationic polymer, cationic surfactant and nonionic polymer, and anionic surfactant and nonionic polymer. The mixtures of anionic surfactant and cationic polymer showed improved foam stability, however, the foaminess was strongly reduced, as compared to the surfactant solutions without polymer. No significant synergistic or antagonistic effects were observed for the mixture of nonionic surfactant (with low critical micelle concentration) and nonionic polymer. The results from the model experiments allowed us to explain the observed trends by the different adsorption dynamics and complex formation pattern in the systems studied.     

Hydrophobization of glass surface by adsorption of poly(dimethylsiloxane)

Silica or glass particles are introduced in a poly(dimethylsiloxane) (PDMS) matrix for various applications. A particular feature of these systems is that PDMS adsorbs on the surface of the dispersed particles, thus rendering them more hydrophobic with time. The mechanism of this process of in situ hydrophobization is still poorly understood. The major aims of the present study are (1) to quantify the rate of surface hydrophobization by PDMS and, on this basis, to discuss the mechanism of the process; (2) to compare the contact angles of surfaces that are hydrophobized by different procedures and are placed in contact with different fluid interfaces-PDMS-water, hexadecane-water, and air-water; and (3) to check how the type of surfactant affects the contact angles, viz., the effective hydrophobicity of the surface. We present experimental results for the kinetics of hydrophobization of glass surfaces, which are characterized by measuring the three-phase contact angle of glass-surfactant solution-PDMS. The data reveal two consecutive stages in the hydrophobization process: The first stage is relatively fast and the contact angle increases from 0 degrees to about 90 degrees within several minutes. This stage is explained with the physical adsorption of the PDMS chains, as a result of hydrogen-bond formation with the surface silanol groups. The second stage is much slower and hours or days are required at room temperature to reach the final contact angle (typically, 150-160 degrees). This stage is explained as grafting of the PDMS molecules on the surface by chemical reaction with the surface silanol groups. If the glass surface had been pretreated by hexamethyldisilazane (HMDS), so that CH(3) groups had blocked most of the surface silanol groups, the first stage in the hydrophobization process is almost missing-the contact angle slowly changes at room temperature from about 90 degrees up to 120 degrees. The experiments aimed to compare several hydrophobization procedures showed that PDMS ensures larger contact angle (more hydrophobic surface) than grafted alkyl chains. The contact angles at the PDMS-water and hexadecane-water interfaces were found to be very similar to each other, and much larger than that at the air-water interface. Interestingly, we found that the ionic surfactants practically do not affect the contact angle of PDMS-hydrophobized surface, whereas the nonionic surfactants reduce this angle. Similar trends are expected with silica surfaces, as well.     

Synergism in the spreading of hydrocarbon-chain surfactants on polyethylene film-anionic and cationic mixtures by a two-step procedure

A study has been made of the adsorption, interaction, and spreading of mixtures of anionic and cationic surfactants at the aqueous solution/polyethylene (PE) interface. When a drop of an aqueous solution of an anionic or cationic hydrocarbon-chain surfactant is placed on a highly hydrophobic PE film (contact angle of water > 90 degrees ), it spreads to an area very little larger than that of a drop of water of the same volume. If the anionic and cationic hydrocarbon-chain surfactant solutions are mixed prior to being applied to PE film, synergism is small, if any, and the reproducibility of the experimental results is poor. However, when the cationic and anionic aqueous solutions are applied on the PE film in a sequential manner, a remarkable synergism in spreading is observed and the results are very reproducible. The area spread by an aqueous solution of the anionic-cationic mixture may be more than 400 times that of aqueous solutions of the same volume and surfactant concentration of the individual surfactant components. Previous work in this laboratory on surfactant systems showing synergism in spreading on PE film, but only weak interaction at the aqueous solution/air interface, showed that the synergy was due to changes at the aqueous solution/PE interface and not to the changes at the aqueous solution/air or PE/air interface. Investigation of the adsorption behavior at the aqueous solution/solid interface of two of the anionic-cationic mixtures studied here indicates the reason for differences in spreading behavior observed with different anionic-cationic mixtures. The more similar the adsorption tendencies at the solid/aqueous solution interface of the anionic and cationic surfactants, and the closer their adsorption to an equimolar monolayer there, the stronger their interaction there and the greater their enhancement of the spreading. A mechanism is proposed for the synergy in spreading observed, based upon the difference between the surface tension in the precursor film at the spreading interface and that at the top of the spreading drop.     

Wetting of Solids by Aqueous Solutions of Surfactant Binary Mixtures: 1. Wetting of Low-Energy Surfaces

Wetting of low-energy surfaces (polymers, hydrophobized glass) by the aqueous solutions of binary mixtures of nonionic (Triton X-100) and cationic (cetyltrimethylammonium bromide) surfactants at the molar fraction of cationic surfactant = 0.2, 0.5, and 0.8 was studied in the wide concentration range. It was shown that the contact angles of mixed solutions at low-energy surfaces could be predicted on the basis of surface tension isotherms. Concentration ranges of wetting synergism were determined.     

Spreading of Surfactant Solutions over Hydrophobic Substrates

The spreading of surfactant solutions over hydrophobic surfaces is considered from both theoretical and experimental points of view. Water droplets do not wet a virgin solid hydrophobic substrate. It is shown that the transfer of surfactant molecules from the water droplet onto the hydrophobic surface changes the wetting characteristics in front of the drop on the three-phase contact line. The surfactant molecules increase the solid-vapor interfacial tension and hydrophilize the initially hydrophobic solid substrate just in front of the spreading drop. This process causes water drops to spread over time. The time of evolution of the spreading of a water droplet is predicted and compared with experimental observations. The assumption that surfactant transfer from the drop surface onto the solid hydrophobic substrate controls the rate of spreading is confirmed by our experimental observations. Copyright 2000 Academic Press.     

Contact angles of liquid drops on super hydrophobic surfaces: understanding the role of flattening of drops by gravity

Measurement of contact angles on super hydrophobic surfaces by conventional methods can produce ambiguous results. Experimental difficulties in constructing tangent lines, gravitational distortion or erroneous assumptions regarding the extent of spreading can lead to underestimation of contact angles. Three models were used to estimate drop shape and perceived contact angles on completely nonwetting super hydrophobic surfaces. One of the models employed the classic numerical solutions from Bashforth and Adams. Additionally, two approximate models were derived as part of this work. All three showed significant distortion of microliter-sized drops and similar trends in perceived contact angles. Liquid drops of several microliters are traditionally used in sessile contact angle measurements. Drops of this size are expected to and indeed undergo significant flattening on super hydrophobic surfaces, even if the wetting interactions are minimal. The distortion is more pronounced if the liquid has a lesser surface tension or greater density. For surfaces that are completely nonwetting, underestimation of contact angles can be tens of degrees. Our modeling efforts suggest that accurate contact angle measurements on super hydrophobic surfaces would require very small sessile drops, on the order of hundreds of picoliters.     

The use of surface tension to predict the formation of 2D arrays of latex spheres formed via the Langmuir-Blodgett-like technique

Highly ordered hexagonal arrays of latex spheres on highly ordered pyrolytic graphite (HOPG) have been prepared from a Langmuir-Blodgett-like (LB-like) technique using both polymers and surfactants as spreading agents. The role of spreading agent concentration in forming a well-ordered, stable monolayer at the air-liquid interface was studied by means of atomic force microscopy, scanning electron microscopy, optical microscopy, and surface tension measurements for three different systems: a nonionic surfactant, octylphenoxy poly(ethyleneoxy)ethanol (Igepal CO 630); an anionic surfactant, sodium dodecyl sulfate; and a low-molecular-weight, water-soluble polymer, polyacrylamide. For both the anionic surfactant and the water soluble polymer, a correlation was found between a unique feature in surface tension measurements of the latex-spreading agent mixture and the concentrations at which hexagonal arrays of latex spheres form on the surface of HOPG. For the nonionic surfactant, no ordered structures were found on HOPG for any surfactant concentration, consistent with no appearance of the unique feature in surface tension measurements. These results show that a tensiometer can be used to determine the conditions under which well-ordered latex films have the possibility of forming on a substrate using the LB-like technique; however, other factors, such as pulling speed and surface chemistry, play a role as well.     

Interaction between polymer and anionic/nonionic surfactants and its mechanism of enhanced oil recovery

Various experimental methods were used to investigate interaction between polymer and anionic/nonionic surfactants and mechanisms of enhanced oil recovery by anionic/nonionic surfactants in the present paper. The complex surfactant molecules are adsorbed in the mixed micelles or aggregates formed by the hydrophobic association of hydrophobic groups of polymers, making the surfactant molecules at oil-water interface reduce and the value of interfacial tension between oil and water increase. A dense spatial network structure is formed by the interaction between the mixed aggregates and hydrophobic groups of the polymer molecular chains, making the hydrodynamic volume of the aggregates and the viscosity of the polymer solution increase. Because of the formation of the mixed adsorption layer at oil and water interface by synergistic effect, ultra-low interfacial tension (～2.0?×?10^?3 mN/m) can be achieved between the novel surfactant system and the oil samples in this paper. Because of hydrophobic interaction, wettability alteration of oil-wet surface was induced by the adsorption of the surfactant system on the solid surface. Moreover, the studied surfactant system had a certain degree of spontaneous emulsification ability (D50?=?25.04?µm) and was well emulsified with crude oil after the mechanical oscillation (D50?=?4.27?µm).     

Superspreading driven by Marangoni flow

The spontaneous spreading (called superspreading) of aqueous trisiloxane ethoxylate surfactant solutions on hydrophobic solid surfaces is a fascinating phenomenon with several practical applications. For example, the ability of trisiloxane ethoxylate surfactants to enhance the spreading of spray solutions on waxy weed leaf surfaces, such as velvetleaf (Abutilion theophrasti), makes them excellent wetting agents for herbicide applications. The superspreading ability of silicone surfactants has been known for decades, but its mechanism is still not well understood. In this paper, we suggest that the spreading of trisiloxane ethoxylates is controlled by a surface tension gradient, which forms when a drop of surfactant solution is placed on a solid surface. The proposed model suggests that, as the spreading front stretches, the surface tension increases (the surfactant concentration becomes lower) at the front relative to the top of the droplet, thereby establishing a dynamic surface tension gradient. The driving force for spreading is due to the Marangoni effect, and our experiments showed that the higher the gradient, the faster the spreading. A simple model describing the phenomenon of superspreading is presented. We also suggest that the superspreading behavior of trisiloxane ethoxylates is a consequence of the molecular configuration at the air/water surface (i.e. small and compact hydrophobic part), as shown by molecular dynamics modeling. We also found that the aggregates and vesicles formed in trisiloxane solutions do not initiate the spreading process and therefore these structures are not a requirement for the superspreading process.     

Organization of amphiphiles: XII. Evidence in favor of formation of hydrophobic complexes in aqueous solution

The effects of nonionic surfactants OP-10 and OP-30 (polyoxyethylated octyl phenols with 10 and 30 oxyethylene groups, respectively) in surfactant mixtures with ionic surfactants hexadecyltrimethylammonium bromide (CTAB) and sodium dodecyl sulphate (SDS) have been investigated by a conductometric method in conjunction with fluorescence, surface tension, zeta potential, and DLS measurements. The interactions are found to be antagonistic in nature for each of the systems; i.e., micellization of CTAB as well as SDS is hindered on addition of the nonionic surfactants. The antagonism is found to be more prominent in the presence of OP-10 compared to that of OP-30. Two types of mechanistic paths, path A operating below the critical micellar concentration and path B operating beyond the critical micellar concentration of nonionic surfactants, have been suggested. In path A, the retardation in micellization has been attributed to a decrease in monomeric concentration of the ionic surfactants from solution as a result of the formation of a hydrophobic complex between nonionic and ionic surfactants. In path B, the decrease in monomer concentration is due to the solubilization of the ionic surfactant in micelles of the nonionic surfactants in a 1:1 stoichiometric ratio. A theoretical treatment to the interaction in each ionic-nonionic pair yields a positive value of the interaction parameter supporting the concept of antagonism. The formation of the hydrophobic complex is supported by fluorescence and surface tension measurements. A schematic representation of the stabilization of these hydrophobic complexes has been suggested. The association of ionic surfactants by nonionic micelles is suggested by zeta potential and DLS studies.     

Interactions between nonpolar surfaces in mixed solutions of cationic and nonionic surfactants

The interaction energy between hydrophobic SiO₂ particles in aqueous solutions of a cationic surfactant (dodecylpyridinium bromide, DDPB), a nonionic surfactant (Triton X-100, TX-100), and their mixed solutions was measured as a function of concentration. Synergism has been observed in mixed surfactant solutions: the surfactant concentration required for achieving the set interaction energy in the mixed solutions was lower than in the solutions of the individual surfactants. The molecular interaction parameters in surfactant mixtures were calculated using the Rosen model. Chain-chain interactions between nonionic and cationic surfactants were suggested as the main reason for the synergism.     

Pulmonary surfactant adsorption is increased by hyaluronan or polyethylene glycol

In acute lung injuries, inactivating agents may interfere with transfer (adsorption) of pulmonary surfactants to the interface between air and the aqueous layer that coats the interior of alveoli. Some ionic and nonionic polymers reduce surfactant inactivation in vitro and in vivo. In this study, we tested directly whether an ionic polymer, hyaluronan, or a nonionic polymer, polyethylene glycol, enhanced adsorption of a surfactant used clinically. We used three different methods of measuring adsorption in vitro: a modified pulsating bubble surfactometer; a King/Clements device; and a spreading trough. In addition we measured the effects of both polymers on surfactant turbidity, using this assay as a nonspecific index of aggregation. We found that both hyaluronan and polyethylene glycol significantly increased the rate and degree of surfactant material adsorbed to the surface in all three assays. Hyaluronan was effective in lower concentrations (20-fold) than polyethylene glycol and, unlike polyethylene glycol, hyaluronan did not increase apparent aggregation of surfactant. Surfactant adsorption in the presence of serum was also enhanced by both polymers regardless of whether hyaluronan or polyethylene glycol was included with serum in the subphase or added to the surfactant applied to the surface. Therefore, endogenous polymers in the alveolar subphase, or exogenous polymers added to surfactant used as therapy, may both be important for reducing inactivation of surfactant that occurs with various lung injuries.